Itunes won't recognize my ipod nano 2nd gen anymore?

itunes won't recognize my ipod nano 2nd gen anymore. it just charges it???

Refer to this article:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538

Similar Messages

  • ITunes and my PC won't recognize my iPod Nano (2nd gen.)

    Just this morning, my iPod nano (2nd gen.) stopped getting recognized in my iTunes and on my computer hard drive. It still charges when it's plugged into the computer, but the device is not recognized otherwise. What is going on?? Thanks!

    p.s. I also connected it to my husband's laptop and his iTunes wouldn't recognize the device either (if that helps).

  • Itunes won't recognize my ipod nano 5th gen. it's recognized by the computer, but I get a message from itunes that says an ipod has been detected, but it couldn't be identified properly. i did all of the steps on the ipod assistant. unistalled and reinsta

    Itunes will not recognize my Ipod Nano 5th g. It shows up on my computer. But Itunes gives me a message that says "An ipod has been detected, but it could not be identified properly. I did all the steps in the ipod assistant. Unistalled and reinstalled drivers and itunes. restarted ipod and even erased everything. It is recognized by other computers. And itunes recognizes my iphone fine.  please help.

    Have you restarted your computer?  iTunes updated? 

  • Itunes won't recognize my ipod nano 4th gen (or any other ipod) as a device

    i've had my ipod nano 4th gen for as long as 4th gen's have been around.  never had a problem with it or itunes.  until now.  all of a sudden, when i plug my ipod in to sync the new music purchased, itunes doesn't even recognize my ipod.  "devices" never even comes up.  "sync ipod" under file isn't highlighted.  my ipod only shows as charging.  since this problem occurred, i've tried my husband's ipod and it isn't recognized.  i've used numerous cords in both USB ports.  i've uninstalled and reinstalled itunes.  nothing is working!  any suggestions would be greatly appreciated!!!!

    Here'sa link that might help
    p://support.apple.com/kb/TS1363

  • My computer doesn't recognize my ipod nano 2nd gen

    My computer running Windows 7 doesn't recognize my ipod nano 2nd gen.  Also my ipod not seen in my itunes.  I did all the reset stuff and nothing works.  Do you think it is just shot???

    Make sure you have the latest version of iTunes. Are you a Mac or PC user?
    Hm so have you also tried completely erasing your iPod?

  • ITunes no longer recognizes my iPod nano 5th gen.  When plugged into macbook usb it appears as my iPhone.  Previously both devices had individual identities. Have reset iPod and turned macbook off/on.

    iTunes no longer recognizes my iPod nano 5th gen.  When plugged into macbook usb it appears as my iPhone.  Previously both devices had individual identities. Have reset iPod and turned macbook off/on.

    Hello BPeery,
    I would go through ALL the steps here:
    iPod not recognized in 'My Computer' and in iTunes for Windows
    Let us know how it goes.
    Hope this helps.
    ~Julian

  • TS1591 How do I get Itunes 11.0 to recognize my IPOD Nano 2nd gen

    How do I get Itunes 11.o to recognize my Ipod Nano 2nd gen

    Same question here with iPod nano 1st gen and 3rd gen. They all stopped working with the iTunes 11 upgrade.

  • Computer does not recognize my ipod nano (2nd gen.)

    Hi!
    I'm having a problem with my 2nd generation ipod nano. My ipod itself works fine! The thing is that my computer won't recognize it. It says something about there being some "malfunction" or other. Also, for some reason it doesn't want to charge right. Can someone please help me with this?

    First of all, try another port on your computer. Some ports are not connected direct to the motherboard and do not recognize the iPod as well as those that are. Reset the iPod each time you connect it to another port.
    Then try with the iPod in forced disk mode.
    Putting iPod into disk mode.
    Still no joy, see if any of these articles help.
    Windows XP cannot detect an iPod.
    USB drivers are not installed properly or are out of date.
    iTunes doesn't recognize the iPod.
    Your Windows PC doesn't recognize iPod

  • Itunes 7.5 doesn't recognize by iPod nano (2nd gen)

    After upgrading to iTunes 7.5, my Macs won't recognize the presence of my iPod nano. The iPod knows its connected, because the battery is charging, but iTunes doesn't know it's there and so can't sync. Any ideas?

    This sounds like what my iPod Classic was doing a few weeks ago (before the 7.5 release of iTunes.) In my case, it turned out to need a simple reset of my iPod...
    Read http://docs.info.apple.com/article.html?artnum=61705 and see if that helps any. If not, take a look at which version of the iPod software yours is running... I know there were a few bum version numbers out for a short while... at least for the Classic.
    -Case

  • My computer & itunes won't recognize my ipod nano is connected

    So my brother got an ipod nano, the the original version with only the colored front panel or whatever, and then I got am ipod nano, the second or newer version and we run them off of the same computer. Well his is no loger in use since it went through the washing machine, anyways I tried to import a cd on my itunes, it worked but itunes wouldn't let me sync (or whatever its called) the songs onto the ipod. So I went back to some little fold up booklet that came with the ipod and it said to put songs from a cd onto your ipod that you have to click on ipod under devices. but the only thing that shows up under devices is the cd that i'm importing not the ipod even though it's connected it also said was that when you plug your ipod into itunes it will show automatically come up. it doesn't. the ipod only charges. so it could be many different things: 1. my itunes isn't compatible with the newer version ipod. 2. it could be my computer. although its only 3 years old and its a Windows XP or 3. its just the ipod. The ipod nano works completely normal, no problems. This is the first time i've ever tried putting on songs from a cd before. I also tried uninstalling itunes from my computer and then re-installing to see if the newer version ipod nano would work by itself. but that didn't work either. under file, edit, options, or something (one of the headings) I went to preferences and clicked on ipod and it said "not connected" but it was. I have no idea what's wrong. i only have 18 songs so far on it too so it's not overused or anything. I also forgot to mention that I installed itunes from the disc that came with my ipod nano, not from this website. at this point in time i don't have itunes installed on my computer because there's really no point. If anyone understands my really confusing issue, help me!! Simplified: My computer doesn't recognize that my ipod nano is plugged in and I've tried two different USB cables so that's not it.
    Philips   Windows XP  

    Try: http://discussions.apple.com/thread.jspa?threadID=743515&tstart=15

  • Itunes won't recognize my ipod nano, and my computer is only recognizing it as a storage device. How do I fix this? I want to add music...

    I have tried reinstalling itunes, but it didn't help. ANy suggestions?

    iPod not recognized in 'My Computer' and in iTunes for Windows
    Call U.S. iPod and Mac technical support: 1-800-APL-CARE (1-800-275-2273) to register your iPod Nano.

  • Itunes won't recognize new Ipod Nano 8GB

    Hi, help someone please. The error I'm receiving is: "An Ipod has been detected, but it could not be identified properly. Please disconnect and reconnect the ipod, then try again".
    Tried this several times and even reinstalled itunes... didn't work. Tried using a different USB port as well.
    All other ipods are working fine when connected. I'm using Windows XP. HELLLPPP please !! it's my kids new Christmas present

    I had exactly the same problem - heres the procedure I used - hope it helps ?
    It looks a bit daunting but only takes a couple of minutes.
    Disconnect iPod
    Go into Start - Control Panel - Add/Remove programs
    Select iTunes and remove ( don't worry all your music should be safe - mine was still there when I reinstalled )
    Next go to apple website, disable your antivirus ( not sure if this is needed, but it's what worked for me) and download and install latest iTunes 9.0.
    After installation - close iTunes
    Reboot your P.C. and then restart your antivirus.
    Next
    Go into Control Panel again, then administrative tools( if you can't see admin tools select classic view from the left panel.
    Then select computer management - then device manager
    Scroll down the list in the right hand panel and expand the universal serial bus controllers section.
    Connect your ipod nano - you should hear a bleep and then the details in the USB controllers list should change ( if iTunes starts just close it )
    From the USB controllers list select the new addition - it'll either say apple ipod usb or Mass storage device something like that( whichever one has just appeared on connection of your ipod )
    Right click on the new entry and select uninstall - at the warning message select ok
    wait for it to complete the removal.
    Right click the entry again and select scan for hardware changes, keep your ipod connected.
    The computer should now find your ipod and reinstall the necessary usb drivers for you.
    Next
    disconnect your ipod
    start iTunes
    on your ipod - press and hold centre button and menu for about 8 seconds - apple logo will appear, - then press and hold centre button and rewind for 6 - 8 seconds- ipod will go into a diagnostic mode.
    a list will appear on ipod screen
    press the centre button and it will select the first parameter on the list then press menu - you will be returned to the diagnostic list but you will be on the second item in the list - once again press the centre button to access, then press menu to return to the list - repeat until you reach the last item on the list "restore". press the centre button and the ipod should restore - apple logo will appear and the ipod will reboot(wait for a minute or so for this to complete )
    Now connect to iTunes - hopefully your ipod will show up on the left hand side ( mine did )
    click on your ipod on the list - you should now have a screen showing your ipod - it may prompt you to download a newer version of software - click don't download.
    on this summary screen select enable disk usage and then click apply - now wait it can take a little while to complete.
    When it is finished the apple logo will be back at the top of iTunes.
    O.k. this is the fun bit and needs to be done quite quickly !
    Read this next section completely before you start
    click restore on iTunes.
    it will say something like download and restore, click this.
    a progress bar will appear - saying extracting software
    followed by another progress bar, restoring "your name" iPod
    my progress bar then showed 3 or 4 blue dots traveling across the progress bar without actually making any progress.
    while this is happening unplug your iPod
    press and hold centre button and menu for 8 seconds - apple logo appears
    then press and hold centre button and play until it says disk mode.
    reconnect your ipod - the progress bar should now slowly complete and at the end say something like ipod will show up on itunes when it reboots.
    wait for the apple logo to appear on your ipod, followed by the start screen ( select language )
    disconnect
    select the language you want to use as from new.
    reconnect and then sync as normal - everything should now work.
    This is what worked for me - it's a bit long winded but so far so good.
    I hope this helps you - it took me about six hours of searching and messing around to finally get this working - my 2 daughters were driving me mad as their new Nano's wouldn't work !!!!

  • The iTunes that still accepts Windows 2000 won't show my iPod Nano (2nd gen

    Help!

    p.s. I also connected it to my husband's laptop and his iTunes wouldn't recognize the device either (if that helps).

  • My Itunes won't recognize my Ipod nano 6th, did the troubleshooting

    Hey,
    So I have an Iphone 4s and I had the same problem with it and solved it by the "verify that the apple mobile device usb driver is installed". It wasn't installed and I installed it by the steps and now it works.
    Tried to do the same to my Ipod nano 6th, and when I'm trying to install the driver (as I did with the Iphone, and as it says in the troubleshooting) I get the next message: "the folder you specified doesn't contain a compatible software driver for your device. If the folder contains a driver, make sure it is designed to work with windows for 64x-based systems".
    I did tried all the other steps as well and nothing worked. I guess the problem is with the driver (as I had the same problem exactly with my Iphone), but it doesn't say in the troubleshooting what to do with this error message.
    Thanks for your help.
    M

    Hey,
    So I have an Iphone 4s and I had the same problem with it and solved it by the "verify that the apple mobile device usb driver is installed". It wasn't installed and I installed it by the steps and now it works.
    Tried to do the same to my Ipod nano 6th, and when I'm trying to install the driver (as I did with the Iphone, and as it says in the troubleshooting) I get the next message: "the folder you specified doesn't contain a compatible software driver for your device. If the folder contains a driver, make sure it is designed to work with windows for 64x-based systems".
    I did tried all the other steps as well and nothing worked. I guess the problem is with the driver (as I had the same problem exactly with my Iphone), but it doesn't say in the troubleshooting what to do with this error message.
    Thanks for your help.
    M

  • ITunes freezes when transferring to iPod Nano (2nd gen)

    Hi All - Slightly atypical issue. I purchased a refurbished 2nd-gen iPod nano, but am having continued difficulty getting music onto it. I am not auto-synching but adding them manually.
    The nano connects fine, iTunes sees it fine. However, when I start transferring songs, iTunes will randomly freeze up. What's strange is that I CANNOT shut iTunes down, even trying to end-task in Task Manager. I have to hard reboot my system, and as soon as the freeze happens, the iPod loses the "DO NOT DISCONNECT" screen and returns to the menu, as if the connection has been broken.
    As of Today, October 21st 2007 I am running the most current versions of both iTunes as well as the iPod software.
    Any advice? I have a very large (130GB+) iTunes library that I've painstakingly manicured to include all obscure artwork, correct genres, etc so I'd rather avoid re-installing everything from scratch.
    Thanks in advance! This is driving me crazy!

    I have the same problem on my nano (gen 1). I have done everything it says in the book, and nothing helps. I have restored several times, but it seems to make no difference. Sometimes everything is recorded, sometimes hardly anything. At this moment it made it through about 3/4 of my songs and has stalled. I don't even know if the Itunes program needs reinstalling or my Ipod is at fault.
    I find it hard to believe this problem is not on the trouble shooting list.
    a2papa

Maybe you are looking for

  • Disable delete button in PO Modify transaction

    Hi I am new to SAP. I want certain user to prevent deleting PO line item in ME22N transaction (either by disabling delete button). Please let me know how go about it. thanks

  • I need to know which install disk to buy for my mac serial number 17*****ZE4

    Need to know which install disk to buy since I lost my original. <Edited by Host>

  • Sounds on facebook and twitter

    Since I bought a iphone 5, I am having trouble with sounds in FB and twitter.  I have rechecked the settings over and over and I can't seem to get notifications to sound or the "tweet" sound when I send a tweet.  What I want is a sound so I know when

  • Table for "Planned Total" in CJ40

    Hi Gurus, I got all the other information but for the Planned Total value in CJ40. Can anyone help me with the table in which this value is stored. Is it directly available or we need to sum the other values ? thanks in advance. Regards, Vinodh

  • PCD Eventing

    Hi, Is it possible for the PCD low level API's of create / modify / delete to send out events, that can be subscribed to, for instance using a portal service? Alternatively is it possible to listen to any change in the PCD? I need to run a few report