IVI error will not run PXI cards calibration
I had an NI automatic update done a week or so ago and it wiped out my ability to run NIMAX, Calibration Executive, and see any of my PXI card plugins. I am using a PXI-1033 mainframe and calibrating multipe PXI cards. I was able to fix NIMAX and I can now see my mainframe and cards in the mainframe, but I cannot communicate with the cards. When I start my computer I get a "found new hardware wizard" looking for a PCI Device but have no luck when I downloaded all the drivers once again. In MAX the card is there but says "windows does not have a driver associated with my device" even after installing it three times. When I tried running Calibration Executitve I get the error message "ProcessModel\QueryDriverVersions\specificDrivers\cex_Read_NI_SCOPEVersion.viat step QueryDriver Versions LabView: The VI is not executable. Most likely the VI is broken or one of its VIs cannot be located. OPen the VI in labview using flie>>Open and verify it is runable."
Here is the report for what I am seeing when I first start up MAX. The error code said “NI Service Locator is not running”, See attachment.
I use this NI Software to calibrate PXI cards listed below using a NI PXI-1033 mainframe. PXI cards are:
PXI-4070
PXI-4461
PXI-5441
PXI-5600
PXI-5610
PXI-5620
When I run Calibration Executive to calibrate a PXI-5600, I see the error code “Error-603 occurred at Open RegistryKey.vi at step Query Driver Versions.
Possible reasons: LabVIEW: Specified key or value does not exist.
When I run Calibration Executive to calibrate a PXI-5620, PXI-5122, I see the error code “Error 1003 occurred at Open VI Reference in cex_ReadDriverVersion.vi-
>cex_FindProcedureINIAndGetVersionInfo. Vi-
>cex_FindProcedureINIAndGetVersionInfo. Vi.ProxyCaller
VI Path: C:\Program Files\National Instruments\Calibration Executive\Source\vi.lib\
ProcessModel\QueryDriverVersions\specificDrivers\cex_Read_NI_SCOPE_Version.vi
At step Query Driver Versions
LabVIEW: The VI is not executable. Most likely the VI is broken or one of its subVIs cannot be located. Open the VI in LabVIEW using File>>Open and verify that it is runnable.
Possible Reasons:
LabVIEW: The VI is not executable. Most likely the VI is broken or one of its subVIs cannot be located. Open the LabVIEW using file>> Open and verify that it is runable.
When I run Calibration Executive to calibrate a PXI-5620, I see the error code “Error 1003 occurred at Open VI Reference in cex_ReadDriverVersion.vi-
>cex_FindProcedureINIAndGetVersionInfo. Vi-
>cex_FindProcedureINIAndGetVersionInfo. Vi.ProxyCaller
VI Path: C:\Program Files\National Instruments\Calibration Executive\Source\vi.lib\
ProcessModel\QueryDriverVersions\specificDrivers\cex_Read_NI_DMM_Version.vi
At step Query Driver Versions
LabVIEW: The VI is not executable. Most likely the VI is broken or one of its subVIs cannot be located. Open the VI in LabVIEW using File>>Open and verify that it is runnable.
Possible Reasons:
LabVIEW: The VI is not executable. Most likely the VI is broken or one of its subVIs cannot be located. Open the LabVIEW using file>> Open and verify that it is runable.
When I run Calibration Executive to calibrate a PXI-5610, I see the error code “Error 1003 occurred at Open VI Reference in cex_ReadDriverVersion.vi-
>cex_FindProcedureINIAndGetVersionInfo. Vi-
>cex_FindProcedureINIAndGetVersionInfo. Vi.ProxyCaller
VI Path: C:\Program Files\National Instruments\Calibration Executive\Source\vi.lib\
ProcessModel\QueryDriverVersions\specificDrivers\cex_Read_NI_RFSG_Version.vi
At step Query Driver Versions
LabVIEW: The VI is not executable. Most likely the VI is broken or one of its subVIs cannot be located. Open the VI in LabVIEW using File>>Open and verify that it is unable.
Possible Reasons:
LabVIEW: The VI is not executable. Most likely the VI is broken or one of its subVIs cannot be located. Open the LabVIEW using file>> Open and verify that it is runable.
When I run Calibration Executive to calibrate a PXI-5441, I see the error code “Error 1003 occurred at Open VI Reference in cex_ReadDriverVersion.vi-
>cex_FindProcedureINIAndGetVersionInfo. Vi-
>cex_FindProcedureINIAndGetVersionInfo. Vi.ProxyCaller
VI Path: C:\Program Files\National Instruments\Calibration Executive\Source\vi.lib\
ProcessModel\QueryDriverVersions\specificDrivers\cex_Read_NI_FGEN_Version.vi
At step Query Driver Versions
LabVIEW: The VI is not executable. Most likely the VI is broken or one of its subVIs cannot be located. Open the VI in LabVIEW using File>>Open and verify that it is runnable.
Possible Reasons:
LabVIEW: The VI is not executable. Most likely the VI is broken or one of its subVIs cannot be located. Open the LabVIEW using file>> Open and verify that it is runable.
I can successfully calibrate a:
PXI-4461
Attachments:
ni_support.zip 1184 KB
Similar Messages
-
Bridge CC on opening gives "Adobe Bridge CC has stopped working" Uninstalled, re-installed same error, will not run. "check online for a solution" does nothing.
Bridge worked great for a while then started to fail when starting. Old Bridge CS6 still works fine. HELP ... please.You problem is in the Fault Module MSVCR80.dll
Do a web search for this. Here is one LINK -
Because of a problem, I uninstalled Firefox once, reinstalled it and it ran. I had a problem so I uninstalled/reinstalled it again. Now it will not run. I get an error message saying that firefox is running and you can only run one at a time. I have uninstalled multiple times and can't figure out what is running. The is only one Firefox installed and it is not open. What does this mean and how do I fix it?
If you use ZoneAlarm Extreme Security then try to disable Virtualization.
*http://kb.mozillazine.org/Browser_will_not_start_up#XULRunner_error_after_an_update
See also:
*[[/questions/880050]] -
After failed update of itunes yesterday, now will not run with error message "MSVCR80.dll not found" APSDaemon.exe will not run. itunes will not now run.
Go to Control Panel > Add or Remove Programs (Win XP) or Programs and Features (later)
Remove all of these items in the following order:
iTunes
Apple Software Update
Apple Mobile Device Support (if this won't uninstall move on to the next item)
Bonjour
Apple Application Support
Reboot, download iTunes, then reinstall, either using an account with administrative rights, or right-clicking the downloaded installer and selecting Run as Administrator.
The uninstall and reinstall process will preserve your iTunes library and settings, but ideally you would back up the library and your other important personal documents and data on a regular basis. See this user tip for a suggested technique.
Please note:
Some users may need to follow all the steps in whichever of the following support documents applies to their system. These include some additional manual file and folder deletions not mentioned above.
HT1925: Removing and Reinstalling iTunes for Windows XP
HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
tt2 -
Itunes will not run on my pc after update: see error messageProblem Event Name: BEX
Itunes will not run on my pc after update, i get this error message:
Problem Event Name: BEX
Application Name: itunes.exe
Aplication Version 10.7.0.21
Application Time Stamp 504d85d9
Fault mode Name: Quicktime.qts_unloaded
Any Ideas on a fix??Fault mode Name: Quicktime.qts_unloaded
Try updating your QuickTime Player to the most recent version. Does that clear up the launch errors? -
I just put itunes upeate 11 on and now itunes will not run. I get an error that sys iTunes has stopped and windows is sutting it down. I reinstalled 10.7 and it will not run eather now.
C Mawle wrote:
Thanks. I have followed all the instructions as recommended and nothing has worked so it looks like the restore/update may have been interrupted - would loss of internet connection do this?
Yes it would, possibly even brick it.
Have successfully connected my ipod nano with iTunes so looks like the device driver is working.
Can I use my ipod nano USB connector to check?
It is not much help to you, since the device that you need still not recognized.
Anyway looks like I may have to swallow the loss of data. Have set-up a call for tomorrow with Apple support so will wait until after this before doing the factory restore!
Good luck, but if you expect miracle from that call good luck again. -
I have put Netflix on my Macbook Pro but Silverlight will not run.I receive a black screen that says "player error." Does anyone have a solution for this. Netflix support is not so hot.I can use Netflix straming thru my Blueray on my TV but it will not run on my Pro. Thanks
Try running Safari in 32 bit mode. In get info box for Safari,
check open in 32 bit mode. There have been some oddities
on some systems that can cause some issues.
I had thought MS had fixed this, but may not have. -
When upgrading quicktime, I get an error code: -3, and itunes will not run.
when upgrading quicktime, I get an error code: -3, and itunes will not run. How do I fix?
i 'm very interest because on 3 PC , i have the same problem and i work at tv producer...
-
I can't install the trial version of Adobe Acrobat because the AdobeDownloadAssistant.exe will not run. I get this error:
"This application cannot be installed because this installer has been mis-configured. Please contact the application author for assistance."
I completed the trial questionnaire & all seemed well. Can anyone help?Downloadable installation files available:
Suites and Programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
Acrobat: XI, X | 9,8 | 9 standard
Premiere Elements: 13 | 12 | 11, 10 | 9, 8, 7 win | 8 mac | 7 mac
Photoshop Elements: 13 |12 | 11, 10 | 9,8,7 win | 8 mac | 7 mac
Lightroom: 5.7.1| 5 | 4 | 3
Captivate: 8 | 7 | 6 | 5.5, 5
Contribute: CS5 | CS4, CS3
Download and installation help for Adobe links
Download and installation help for Prodesigntools links are listed on most linked pages. They are critical; especially steps 1, 2 and 3. If you click a link that does not have those steps listed, open a second window using the Lightroom 3 link to see those 'Important Instructions'. -
Just attempted to download current update of Itunes into my HP computer with Windows 7. I've never had trouble before but now it will not run. Runtime Error R6034 an app has make an attempt to load the C runtime library incorrectly. Itunes Error 7
Click here and follow the instructions. You may need to completely remove and reinstall iTunes and all related components, or run the process multiple times; this won't normally affect its library, but that should be backed up anyway.
(99714) -
148:3, is showing up as an error and my program will not run, what to do ?
148:3, is showing up as an error and my program will not run, what to do ?
Error 148:3 is a licensing error for Adobe Paid apps like Photoshop or Flash Professional...
WHERE exactly are you seeing this error? -
Firefox hangs with an error message something like - Script not complete or still running.
I cannot uninstall Firefox with the uninstall program routine in the Control Panel and the Mozilla uninstall helper.exe program will not run either. How do I completely uninstall Firefox so I can make a clean reload?
== This happened ==
Every time Firefox opened
== Not sure but I think it was after the updateThanks for the reply.
I am very new to these forums (or is it fora?).
I didn't know there was a Tomcat forum.
How to I find it.
Ta much & best regards,
Pete -
We are trying to install elements 11 but the program will not run error 213:11
we are trying to install elements 11 but the program will not run error 213:11
http://helpx.adobe.com/creative-suite/kb/error-store-does-not-allow.html
-
Itunes error 45075, itunes will not run help
from a system clean up and deletion of restore points!! iTunes ill not run I have tied reinstalling, repairing, uninstalling following with an install and still it will not run! I have obviously deleted something relatively important and now the computer has no restore point which will resolve my issue.
Help is greatly appreciated.The 2096 erro may be associated with running in compatabilty mode, see:
http://docs.info.apple.com/article.html?artnum=305212
None of the tick boxes on the compatability tab should be checked.
It is also worth checking iTunes.exe in c:Program Files\iTunes. -
Delighted with the new iMac but I have had an old version of CS4 for years now and it will not run on the new machine. I have tried Adobe customer care chat but it seems that nobody is available right now. Can anyone help?
I cannot locate the Flexnet folder by the way.... and the License recovery tool tells me that ....
You can’t open the application “LicenseRecoveryLauncher” because PowerPC applications are no longer supported.
Where do I go from here please?
Maybe you are looking for
-
Six-month-old MacBook Pro acting up.
Hello, My mid-2012 13-inch MacBook Pro is running very slow and hot now. Sometimes, it speeds up a little but it msotly is very slow. It booted up to a sort of "question mark/folder" logo on Friday - right after I brought it home from AppleCare - but
-
Java Heap Space error while reading from Excel
Hello, I have a data flow which reads from excel and updates records in an oracle table. When the data flow tries to read the excel I get a java Heap space Error. Error preparing to read <SUPP_STG3_FILE1>: <Java heap space>. Data flow <DF_SUPP_STG3_U
-
No one is creator so no one can kick?
Does anyone know a solution to this? I was creator of a CHAT and I left the chat and got invited back. Now this unwanted person joined and now we have no creators/admins/mods to kick him. Is there a command where people can solve this problem?
-
Network folder opens/closes/disappears/reappears on its own (really)!
I have an external drive hanging off my Airport Extreme and accessed wirelessly. I just created a new folder on the drive to save some files I want to share with another machine on my local network. I copied some files to it (which didn't appear in F
-
my Visa was charged for a purchase thru compaq. if i have my credit card company file a complaint would you be able to trace the shipping address??