IVR NAT - can someone explain how this works?

The CLI config guide, cookbook, and other things I have found do not explain exactly what is getting translated to what with regards to IVR NAT. I setup a simple scenario, and its all working but I am trying to understand how virtual domains and NAT in general is making it all work.
I setup two switches, MDS1 and MDS2. I put VSAN 10 on MDS1 with a single HOST and VSAN 20 on MDS2 with a single DISK. I made a common transit VSAN between them, VSAN 99 via FCIP. Here is my confused take on what is happening.
HOST can only communicate with DISK if it were in its own VSAN10, which its not. So a FCID is created in VSAN10 of 0x9a6e9f so it can talk to it. This is using domain 9a, which is a virtual domain, not an actual domain so when traffic is directed to it, the MDS re-writes it to 0x736ef8 which is a virtual domain fcid, then the far side mds notices it can get to that pwwn and maps it back to the real fcid in vsan 20 of 0x0900ef. Is this even close? I just want to understand how the "routing" is really working. I understand there is a topology table built, which in this case it is:
MDS1 10,99
MDS2 20,99
(I am using auto topology). Below I have outputs I captured. I had to type these in by hand as there was no way to cut/paste of of the lab I was using. I appreciate any help on this, sorry for the marathon of posts here lately.
MDS1
HOST VSAN10
MDS2
DISK VSAN20
I setup an IVRZoneset so that the HOST and the DISK could see eachother. I am using CFS and IVR NAT as well.
So it works great, the HOST can see the DISK. But I am trying to find out about the translations, here are the tables:
P26-MDS-1# show fcns database
VSAN 10:
FCID TYPE PWWN (VENDOR) FC4-TYPE:FEATURE
0x9a6e9f N 22:6e:00:0c:50:17:26:00 (Seagate) scsi-fcp:target
0xbd0000 N 21:00:00:e0:8b:07:4c:5a (Qlogic) scsi-fcp:init
Total number of entries = 2
VSAN 99:
FCID TYPE PWWN (VENDOR) FC4-TYPE:FEATURE
0x736ef8 N 22:6e:00:0c:50:17:26:00 (Seagate) scsi-fcp:target
0xa85c9f N 21:00:00:e0:8b:07:4c:5a (Qlogic) scsi-fcp:init
Total number of entries = 2
P26-MDS-1# show flogi data
INTERFACE VSAN FCID PORT NAME NODE NAME
fc1/5 10 0xbd0000 21:00:00:e0:8b:07:4c:5a 20:00:00:e0:8b:07:4c:5a
Total number of flogi = 1.
P26-MDS-2# show fcns database
VSAN 20:
FCID TYPE PWWN (VENDOR) FC4-TYPE:FEATURE
0x0900ef N 22:6e:00:0c:50:17:26:00 (Seagate) scsi-fcp:target
0x385c50 N 21:00:00:e0:8b:07:4c:5a (Qlogic) scsi-fcp:init
VSAN 99:
FCID TYPE PWWN (VENDOR) FC4-TYPE:FEATURE
0x736ef8 N 22:6e:00:0c:50:17:26:00 (Seagate) scsi-fcp:target
0xa85c9f N 21:00:00:e0:8b:07:4c:5a (Qlogic) scsi-fcp:init
P26-MDS-2# show flogi data
INTERFACE VSAN FCID PORT NAME NODE NAME
fc1/6 20 0x0900ef 22:6e:00:0c:50:17:26:00 22:6e:00:0c:50:17:26:00
Total number of flogi = 1.
P25-MDS-1# sh ivr virtual-domain
VSAN # Domains IVR Virtual Domains
10 1 154
99 2 115,168

You found the correct command to view how the FCID is rewritten as the frame is transferred from 1 VSAN to another. The re-writes for data frame headers are done by the line cards at wire rate. Some control frames that contain the FCID in the payload are routed to the supervisor so that the payload can be updated with the new FCIDs as well.
- Mike

Similar Messages

  • Can anyone explain how this works (vlans and bridge groups)

    Can someone please explain how this works...I have started to have problems but nothing changed. My problems are vlan1 and 1000 getting blocked on the switchport where the root bridge is attached.
    ROOT BRIDGE:
    ssid state
    station-role root bridge
    rts threshold 4000
    concatenation
    interface Dot11Radio0.1
    encapsulation dot1Q 1 native
    no ip route-cache
    no snmp trap link-status
    bridge-group 1
    bridge-group 1 spanning-disabled
    interface Dot11Radio0.911
    encapsulation dot1Q 911
    no ip route-cache
    no snmp trap link-status
    bridge-group 5
    interface Dot11Radio0.1000
    encapsulation dot1Q 1000
    no ip route-cache
    no snmp trap link-status
    bridge-group 2
    bridge-group 2 spanning-disabled
    interface Dot11Radio0.2001
    encapsulation dot1Q 2001
    no ip route-cache
    no snmp trap link-status
    bridge-group 253
    bridge-group 253 spanning-disabled
    interface Dot11Radio0.2120
    encapsulation dot1Q 2120
    no ip route-cache
    no snmp trap link-status
    bridge-group 7
    interface Dot11Radio0.2330
    encapsulation dot1Q 2330
    no ip route-cache
    no snmp trap link-status
    bridge-group 3
    bridge-group 3 spanning-disabled
    interface Dot11Radio0.2336
    encapsulation dot1Q 2336
    no ip route-cache
    no snmp trap link-status
    bridge-group 4
    interface Dot11Radio0.2350
    encapsulation dot1Q 2350
    no ip route-cache
    no snmp trap link-status
    bridge-group 6
    interface Dot11Radio0.2901
    encapsulation dot1Q 2901
    no ip route-cache
    no snmp trap link-status
    bridge-group 255
    bridge-group 255 spanning-disabled
    interface Dot11Radio0.2902
    encapsulation dot1Q 2902
    no ip route-cache
    no snmp trap link-status
    bridge-group 254
    bridge-group 254 spanning-disabled
    interface FastEthernet0
    no ip address
    no ip route-cache
    interface FastEthernet0.1
    encapsulation dot1Q 1
    no ip route-cache
    no snmp trap link-status
    interface FastEthernet0.911
    encapsulation dot1Q 911
    no ip route-cache
    no snmp trap link-status
    bridge-group 5
    interface FastEthernet0.1000
    encapsulation dot1Q 1000 native
    ip address 10.0.32.10 255.255.255.0
    no ip route-cache
    no snmp trap link-status
    bridge-group 1
    interface FastEthernet0.2001
    encapsulation dot1Q 2001
    no ip route-cache
    no snmp trap link-status
    bridge-group 253
    bridge-group 253 spanning-disabled
    interface FastEthernet0.2120
    encapsulation dot1Q 2120
    no ip route-cache
    no snmp trap link-status
    bridge-group 7
    interface FastEthernet0.2330
    encapsulation dot1Q 2330
    no ip route-cache
    no snmp trap link-status
    bridge-group 3
    interface FastEthernet0.2336
    encapsulation dot1Q 2336
    no ip route-cache
    no snmp trap link-status
    bridge-group 4
    interface FastEthernet0.2350
    description 81 River Rd - Labor
    encapsulation dot1Q 2350
    no ip route-cache
    no snmp trap link-status
    bridge-group 6
    interface FastEthernet0.2901
    encapsulation dot1Q 2901
    no ip route-cache
    no snmp trap link-status
    bridge-group 255
    bridge-group 255 spanning-disabled
    interface FastEthernet0.2902
    encapsulation dot1Q 2902
    no ip route-cache
    no snmp trap link-status
    bridge-group 254
    bridge-group 254 spanning-disabled
    interface BVI1
    ip address 10.0.32.10 255.255.255.0
    no ip route-cache
    ip default-gateway 10.0.32.1

    NON-ROOT BRIDGE#2:
    ssid state
    station-role non-root bridge
    rts threshold 4000
    concatenation
    infrastructure-client
    interface Dot11Radio0.1
    encapsulation dot1Q 1 native
    no ip route-cache
    bridge-group 1
    bridge-group 1 spanning-disabled
    interface Dot11Radio0.1000
    encapsulation dot1Q 1000
    no ip route-cache
    bridge-group 254
    bridge-group 254 spanning-disabled
    interface Dot11Radio0.2001
    encapsulation dot1Q 2001
    no ip route-cache
    bridge-group 252
    bridge-group 252 spanning-disabled
    interface Dot11Radio0.2336
    encapsulation dot1Q 2336
    no ip route-cache
    bridge-group 251
    bridge-group 251 spanning-disabled
    interface Dot11Radio0.2901
    encapsulation dot1Q 2901
    no ip route-cache
    bridge-group 253
    bridge-group 253 spanning-disabled
    interface Dot11Radio0.2902
    encapsulation dot1Q 2902
    no ip route-cache
    bridge-group 255
    bridge-group 255 spanning-disabled
    interface FastEthernet0
    no ip address
    no ip route-cache
    hold-queue 80 in
    interface FastEthernet0.1000
    encapsulation dot1Q 1000 native
    no ip route-cache
    bridge-group 1
    interface FastEthernet0.2001
    encapsulation dot1Q 2001
    no ip route-cache
    bridge-group 252
    bridge-group 252 spanning-disabled
    interface FastEthernet0.2336
    encapsulation dot1Q 2336
    no ip route-cache
    bridge-group 251
    bridge-group 251 spanning-disabled
    interface FastEthernet0.2901
    encapsulation dot1Q 2901
    no ip route-cache
    bridge-group 253
    bridge-group 253 spanning-disabled
    interface FastEthernet0.2902
    encapsulation dot1Q 2902
    no ip route-cache
    bridge-group 255
    bridge-group 255 spanning-disabled
    interface BVI1
    ip address 10.0.32.11 255.255.255.0
    no ip route-cache
    ip default-gateway 10.0.32.1

  • EFax. Can anyone explain how this works and on what printers?

    HP and eFax are rather mum on how this works. Can you set the 6500a + to save incoming faxes? What are the printers that can use this?

    Hello mistercrowley,
    Currently eFax is only available on the Hp Photosmart eStation e All in One Printer C510a. The OfficeJet 6500a Plus has the standard analog fax.
    **Click the KUDOS star on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
    (Although I am employed by HP, I am speaking for myself and not for HP)

  • Can Someone Explain How Xorg Works Like This?

    My friend uses Ubuntu, and this is his xorg.conf .
    # xorg.conf (X.Org X Window System server configuration file)
    # This file was generated by dexconf, the Debian X Configuration tool, using
    # values from the debconf database.
    # Edit this file with caution, and see the xorg.conf manual page.
    # (Type "man xorg.conf" at the shell prompt.)
    # This file is automatically updated on xserver-xorg package upgrades *only*
    # if it has not been modified since the last upgrade of the xserver-xorg
    # package.
    # Note that some configuration settings that could be done previously
    # in this file, now are automatically configured by the server and settings
    # here are ignored.
    # If you have edited this file but would like it to be automatically updated
    # again, run the following command:
    # sudo dpkg-reconfigure -phigh xserver-xorg
    Section "Device"
    Identifier "Configured Video Device"
    EndSection
    Section "Monitor"
    Identifier "Configured Monitor"
    EndSection
    Section "Screen"
    Identifier "Default Screen"
    Monitor "Configured Monitor"
    Device "Configured Video Device"
    EndSection
    I know it says
    # Note that some configuration settings that could be done previously
    # in this file, now are automatically configured by the server and settings
    # here are ignored.
    but still. Can someone enlighten me?

    I may be missing something but it seems that your friend doesn't need an xorg.conf at all (if that xorg.conf works for him). In fact, until the recent Xorg upgrade, my desktop didn't need an xorg.conf either. What, exactly, is the cause of your bewilderment?
    Last edited by string (2008-12-04 23:07:42)

  • HT5463 In my opinion, when the Silence setting is "only when the device is locked", it contradicts the settings you set above, like Manual. Can someone explain how these settings work together?

    Can someone explain how these settings work together? Manual seams to contraduct the SILENCE setting at the bottom of the Do Not Disturb page. It's very confusing.

    You should have seen information in the support document that you linked from. It used to be with the first version of Do Not Disturb that it would only function when the device was locked. That changed with iOS 7, and not it can be active all of the time. With it on Manual, it is on, but if you have the device "awake" that you can still receive calls/texts, etc. Sort of like you have the phone awake, so it isn't a problem for you to receive things. If you set the settings for Always, this means you can be doing things on the phone and not be disturbed by anything else. Does that make sense?

  • Can someone explain how .prel files work?

    Can someone explain how .prel files work?  My C drive is O/S and programs, my D drive is storage and the project file(s) (the .prel file) are on my E drive. 
    How is this supposed to be more efficient/faster?  P.E. (C drive) has to constantly communicate back and forth across drives with the .prel file and all the files in the subfolders?  It seems like it would be slower. 
    As I mentioned in a previous post; my zooms in/out of the Timeline are VERY slow.  It is almost 1 second before the Timeline gets bigger/smaller.  Any info would be great,thanks!
    Elwood
    Windows 7 64 bit, i7 980x @333 6 core processor, 12 GB ram DDR 1600, Radeon 5850 GPU PE 9

    By using multiple HDD's, one is spreading the I/O (Input/Output) load over various HDD's. The controller is faster than a single HDD, being tasked to read/write from/to multiple places. One of the first laws of physics is that an object cannot be in more than one place, at the same time. The heads on a HDD are no different. If requests for multiple reads are made, the heads will position themselves over on place on the platters, read, and then move to the next requested location, and so on. However, with multiple HDD's, and a good, fast controller, the heads of each HDD will be placed, where necessary, so reads are done at once, from multiple locations.
    For ultimate performance, a good setup would be as follows:
    C:\ system OS and programs (more reading being done here, than writing)
    D:\ Project files (PREL's in this case)
    E:\ RAID 0 Scratch Disks for Media Cache, but not Render files (both reading and writing)
    F:\ RAID 0 Media files (more reading, but also writing)
    G:\ RAID 0 Export/Share and Render files
    Some go so far as to separate out Audio Assets from Video Assets, and use a separate RAID 0 for each
    The downside of that "ultimate performance" setup, is that when a Project is completed, to clean up, one has to go to many HDD's, and locations. There can also be issues when Archiving a Project, because things are scattered about.
    I get "good performance" by having my Project, Copies of my Assets and all Scratch Disks on one HDD. What I give up in performance, I make up for with housekeeping chores, when the Project is done. I still spread my OS/programs from my Projects, with separate physical HDD's.
    Good luck, and hope that this helps,
    Hunt
    PS - Above, I mention RAID 0, but even greater speed can be achieved via many HDD's in the Array, and perhaps a RAID 50. RAID 0 is just two physical HDD's. Also, for RAID, I recommend a dedicated RAID controller card, and NOT software, or the MoBo's RAID capability.

  • I have just downlaoded the color burst app, can someone explain how to use it?

    I have just downlaoded the color burst app, can someone explain how to use it??
    There is no help in the app and i can't log onto the smart solutions..it is really frustrating me because it is propably a really simple app...can someone please help???

    I posted in this thread an example that illustrates how to use the 3d graph to do surfaces ac lines.
    The type of data that you present to the 3d graph depends on which mthod you are using. In general you want to present a set of points that need plotted. These points are defined by taking one value for each of the XYZ and sometimes W arrays.
    Explanation:
    You want to plot a surface that is defined by four point (X0,Y0,Z0,W0), (X1,Y1,Z1,W1), etc. You can present the values using (4) 2-d arrays each of which have four values at index (o,o), (0,1), (1,0) and (1,1).
    Thie first point plotted would be the point that is defined by taking (0,0) from each of the arrays.
    So as you can see from the above all of your arrays should be of the same size and dimensions for this to work.
    Look at the Example i posted in the other thread and try some small experiments with small data sets before you jump to anything complicated.
    I hope that helps,
    Ben
    Ben Rayner
    I am currently active on.. MainStream Preppers
    Rayner's Ridge is under construction

  • Please can someone explain how to delete email addresses?  I have people who when I type in their name it comes up with the correct email address but then when you hit return to confirm it promptly changes the name to someone else (always the same someone

    Please can someone explain how to delete and email address that when typed in brings up one name but when you hit return to confirm it jumps to another name.  I can't find them in my contacts list but they do come up when you type the first few letters of a name.
    EG If I type xyz and the name of the person comes up, when I press return to confirm that's the one I want then it jumps to [email protected],  always the same def address.
    I can't fathom it out.
    Thanks
    Terri

    Try this:
    Start a new email.  In the To address bar, type in xyz like you normally do, press return to confim, and when the address you want to remove shows up in the address bar, move your cursor over the address you want to delete.
    A small triangle next to the name will show up.  click on it, a drop down menu will open, click Remove from Previous Recipients List.  Then do the drop down menu again and Remove Address.
    Good luck.

  • Recently updated Numbers to Version 3.5.2 and now also seem to have Numbers Version 2.0 on my launchpad? Can anyone explain how this has happened - how do I get rid of it?

    Recently updated Numbers to Version 3.5.2 and now also seem to have Numbers Version 2.0 on my launchpad? Can anyone explain how this has happened - how do I get rid of it? Not able to move to Trash.

    What is strange however is that my iMac is only a few months old and they all were upgraded to V3.x just a few months ago - with all Apps for iWork removed at that time.
    Unless you did something specific to remove the old versions of the iWork apps (not advisable) then, as Wayne points out, they were not actually removed from your Mac, just moved into that subfolder within your main Applications folder.
    I originally downloaded Numbers 2.x from the App Store (i.e. didn't install from a disk). I still have it on my Mac.  But only Numbers 3.x appears in Launchpad.
    I don't know whether this will help, but in Mac App Store you might try clicking 'Account' under 'Quick Links' on the right, signing in with your password, and clicking the 'Reset' button to the right of 'Reset all warnings for buying and downloading'.  Sometimes the App Store gets a little confused. It's possible Launchpad may be taking its cue from the App Store in showing that old version of Numbers.
    By Launchpad I assume you really mean Launchpad, not the Dock.  I usually use the Dock. If that's what you're using too, then of course you can just drag the icon for the old Numbers off the Dock and it will vanish. (But the Numbers 2.3 application will still be there in that subfolder when you need it.)
    SG

  • HT1665 I am trying to connect my Samsung Bluetooth device with my new Iphone 4S.  Can anyone explain how this is done?

    I am trying to connect my Samsung Bluetooth device to my new Iphone 4s. Can anyone explain how this is don?

    Which Samsung Bluetooth device?
    Please note that the iPhone will not pair with other phones, tablets, etc for purposes of file transfer.

  • Can someone explain how the visit count works? Why would it say I visited a site over 600 times? Anyone know how this counts these visits?

    I'm trying to do a detailed log of my computer history. Most of the sites I visited have a visit count of 1, but then I will come across a page that will list 77 or 683 as the visit count. Just wondering if someone can explain how this tracker counts the visits and over what duration of time. Is there a way I can look this up myself?
    == This happened ==
    Not sure how often

    Jneklason wrote:
    ~snip~
    I know this email is confusing and really hard to understand...perhaps now you will know how i've been feeling--lost and confused with all the mis-information, with a hit and miss phone, and out of time with all the 1 1/2 hr to 2 hrs EACH wasted on this issue.
    On top of all this, I can't even find out how to file a complaint with anyone higher up than Customer Service.
    I hate to tell you this, but you didn't write an email. You wrote a discussion post on the Verizon Wireless Community forum which is a public peer to peer forum. Unfortunately since you didn't mark your post as a question, the VZW reps that roam this community won't ever see your post. Before you re-post it, don't. Duplicate posts get removed from the community.
    I see there were several missteps both by the reps and yourself in your post. First you should have insisted on returning the phone within the 14 day return policy period. Second which Samsung Galaxy mini model did you purchase? The S3 mini or the S4 mini? Did you do any research prior to deciding on this device. The reps at that time deflected the easiest course of action, by trying to get you to replace the phone under insurance instead of returning the phone. The Early Edge payment option requires the current phone on the line using the early Edge must be returned to Verizon Wireless. Did you once considered going to a third party site like Swappa to purchase a gently used device for your daughter?

  • Can someone explain how to set up an administrator account so that I can have my phone and my daughters have separate apple ids?

    I mistakenly updated to the latest version of iOS and ever since then I can send messages to my daughter and I receive them but she does not.  She has an iphone also and her phone is under my apple id also.  Someone told me that I could set up an Administrator Account so that she can still be under my account but she has her own ID and that will fix the problem with text/imessages.  I can't find anything on the website that explains how to do that.  Can someone explain that to me?
    Thanks!

    I'm still not clear on what you are trying to accomplish. If you have an iPhone and she does as well you should have your own Apple IDs.
    If you want to pay for any purchases she makes with her phone as far as apps/music goes than that is what Family sharing is for.
    In my case my Wife and I are setup for family sharing. When she purchases music/apps it charges my credit card. This setup also allows me to share my past music/app purchases with her and vice versa.

  • Can someone explain how data is fed to the usage details screen in My Verizon?

    Can someone explain to me how I can view my data usage for a past date today and when I look at the same date a few days from now there will be additional data. Customer support were adamant that the data usage details come directly from my device so I commented that my device must be saving usage and sending it to Verizon arbitrarily to which I was met with silence on the line.
    Here's an example - on 4/1 I checked my data usage details for the date of 3/21 and it looked like this:
    03/21/12
    08:43:00 PM
    0.02518
    03/21/12
    09:17:00 AM
    0.01475
    03/21/12
    07:20:00 AM
    0.01730
    then on 4/7 when I checked my data usage details for the date 3/21 it looked like this:
    03/21/12
    11:45:00 PM
    1.15382
    03/21/12
    11:38:00 PM
    0.24853
    03/21/12
    08:43:00 PM
    0.02518
    03/21/12
    07:50:00 PM
    1.03191
    03/21/12
    06:55:00 PM
    1.18499
    03/21/12
    06:10:00 PM
    1.03968
    03/21/12
    09:17:00 AM
    0.01475
    03/21/12
    07:20:00 AM
    0.01730
    The red rows have been added between 4/1 & 4/7, but where did they come from? This is just one example, it's happening all over my bill and Verizon cannot justify the anomaly and certainly won't consider removing the $40 in overage charges I have this month. Which brings up another question, why doesn't Verizon offer more than 10GB for the mifi? If I want to use more data and am willing to pay for it, I have to go to another provider?

    Hi kellieh,
    When you had your data overage (and the additional spurious charges), how did Verizon respond to you?
    I have just reported a 2x discrepancy between individual device data usage (.89 GB total) and the reported 1.5 GB for my account.  They claim it will take 72 hours to get back to me after they research the problem.
    What avenues did you pursue to make contact?
    I caled 611, then emailed tech support, then sent a private message to Verizon Wireless support.

  • Can someone explain me this?

    Can someone explain me why LabVIEW embeds the graphic in sheet 1 if i specify location as "prueba"? The vi is for LV 5.0.1f1 and Excel 2000, it just creates a workbook, adds some data and creates a chart. I've tried to ask a NI engineer but i receive no answer.
    Thanks,
    Gorka
    Attachments:
    Untitled.llb ‏430 KB

    Hi Gorka,
    I am not sure if this helps but the help file for the add Sheets method says
    "Add Method (Sheets Collection)
    Creates a new worksheet, chart, or macro sheet.
    Syntax
    expression.Add(Before, After, Count, Type)
    expression Required. An expression that returns a Sheets object.
    Before Optional Variant. An object that specifies the sheet before which the new sheet is added.
    After Optional Variant. An object that specifies the sheet after which the new sheet is added.
    Count Optional Variant. The number of sheets to be added. The default value is one.
    Type Optional Variant. Specifies the sheet type. Can be one of the following XlSheetType constants: xlWorksheet, xlChart, xlExcel4MacroSheet, or xlExcel4IntlMacroS
    heet. The default value is xlWorksheet.
    Remarks
    If Before and After are both omitted, the new sheet is inserted before the active sheet.
    *******" (I added asterisks for emphesis).
    the help for the "location method" says,
    "Add Method (Sheets Collection)
    Creates a new worksheet, chart, or macro sheet.
    Syntax
    expression.Add(Before, After, Count, Type)
    expression Required. An expression that returns a Sheets object.
    Before Optional Variant. An object that specifies the sheet before which the new sheet is added.
    After Optional Variant. An object that specifies the sheet after which the new sheet is added.
    Count Optional Variant. The number of sheets to be added. The default value is one.
    Type Optional Variant. Specifies the sheet type. Can be one of the following XlSheetType constants: xlWorksheet, xlChart, xlExcel4MacroSheet, or xlExcel4IntlMacroSheet. The default value is xlWorksheet.
    Remarks
    If Before and After
    are both omitted, the new sheet is inserted before the active sheet.
    Just trying to help,
    Ben
    Ben Rayner
    I am currently active on.. MainStream Preppers
    Rayner's Ridge is under construction

  • How much does this cost? & I still can't understand how this work

    How much does this cost? & I still can't understand how this work

    Hello mkopti,
    ePrint is a free feature include on most of our wireless printers that are e-all-in-one enabled. It allows you to register your printer on HP's website http://www.eprintcenter.com and create an account. Once an account has been created you can enable the web services feature, after connecting to a valid network with internet access, which will print off a registration code you can use to add the printer to your account and customize an email address for the printer. This allows you to print to the printer from virtually anywhere simply by sending an email to the printers email address and when it is received it will print.
    Most of these printers are also Airprint enabled meaning you can print locally from the same network on the iPad, iPod, and iPhone (version 4.3.2 and higher) by using the built in "Print" command in the idevices.
    If you have any other questions or need clarification feel free to reply to this post and I will try to answer any questions you have.
    If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
    Although I work for HP, my posts and replies are my own opinion and not those of HP.

Maybe you are looking for