IVR Setup (MPLS to Data network & PSTN netowrk)

Dear Friends,
Please provide me great full support any body....
I have a requirement of IVR call center config....
My resources ...
1. I have a 2 Mbps MPLS bandwidth at my office,
2. I have Cisco 867VAE-K9 Router,
3. I have a server & client setup for IVR
4. I have Linephone syntal (VOIP Phones)
5. I have a L2 switches.....
My requirement.......
Please find the attached screen shot & I wanted to config data network & parallel do the PSTN config for IVR Setup on the same router (Cisco 867) from MPLS Line... as shown on image.
Kindly advice me for data & pstn line how can I config....
Is do required any voice channel creating on C867, if required please help me with config.....
Could you explain me what is cpe router & media gateway on attached pic,
what type of physical connectivity is required from CPE Router to PSTN via media gateway.....
Thanks & Regards,
Srinivas. N. 

Hi,
Let me explain terms CPE and Media gateway based on your topology
CPE (Customer Premises  Equipment) : This is a router which will be placed in customer site by ISP to terminate MPLS connection or lease lines.
Media gateway: It is device which is used to convert digital voice signal from ISDN PRI line to IP packet . see Wikipedia for correct explanation.
Solution for Voice,
In your pic, PRI line is terminating on media gateway. So you should register this media gateway with call manager using either MGCP or H.323 protocol. I would prefer MGCP because of less overhead to configure.
Configuration required in Media gateway.( Assuming media gateway is a cisco router and you have cisco call manager)
You can connect CPE with media gateway using Ethernet cable.
Basic IP configuration which should be reachable from your call manager.
ISDN PRI configuration in E1 port.
MGCP Backhaul configuration.
Register this router in Call Manager as a MGCP gateway.
Follow the link for the configuration example
https://supportforums.cisco.com/document/90521/mgcp-gateway-integration-cucm-and-pstn-service-provider
Configuration Required in CPE router.
You only need to do WAN ip, LAN ip and static routing configuration in CPE router which will normally doing by service provider. No need to do any voice related  configuration.
Rest all the configuration in IVR server and Call manager. Also you need  to register IP Phone with Call manager and as well as agent configuration required in IVR server for this phones.
HTH,
Regards,
Naisam

Similar Messages

  • Cannot install APN configurations profile for H2O data network

    I am helping a friend of mine with his new unlocked iPhone he got from apple. It is not Jailbroken. In order to get to the data network, he has to install a profile to setup the APN configurations. The phone refuses to install because their can only be one APN configurations profile at a time. This issue should be solved by removing any old profiles that may cause the conflict. The problem is that there are no other profiles installed on the phone at all. In fact, I couldn't even make the profile option show up before installing another profile.
    I read in the internet that sometimes, if you update your phone the system may hide any old profiles it doesn't like. Is this true? If it is, is there away to remove the hidden profiles without doing a full reset to the device and wipe everything I have in there?
    iPhone 4 with iOS 4.3.2

    Hello,
    you don't need to sign the MDM profile with the APNS-certificate, and to my best knowledge you shouldn't even do it. The APNS-certificate is solely for the purpose of authenticate the MDM-commands your server sends to Apple's Push notification service.
    The installed MDM-profile on your device can be unsigned or signed with a SSL-webservercertificate from one of the trusted standard-CAs like Verisign or Thawte.
    You should make sure that your MDM-server either delivers it unsigned (which is failsafe and works) or upload a trusted SSL-certificate (together with the private key, usually in .PFX-format) for this task.
    One of the initial obstacle in Apple-MDM is to understand which classes of certificate are required and to understand their respective purpose.
    Best regards,
    Detlev

  • Having issues with picture messaging get told to go to settings, then general, then network then cellular  data network. my problem is there is no such option my  phone is a 3gs

    having issues with MMS messaging instruction for setup,  are to gotto settings, then general, then network then cellular data network.My problem is there is no cellular data network optiion on this page have tried resetting phone , no good .Help.

    That option does not exist depending on who the carrier is.
    Who is the carrier?  Are they a supported carrier?
    Have you tried Settings > General > Reset > Reset Network Settings?

  • "Data network not found" message

    I've had my phone for about 3 weeks now. Yesterday, I'm on the road and the phone will not pick up a data network signal. I figured it was just a bad area, but then I roamed all over Boston and could not pick up a data signal even though the bars were full. Went out of town and same problem. Later, I realized that I couldn't make or receive calls either. Finally, I turned off the phone then turned it back on, which fixed the phone call issue (and all these messages came up), but then I tried using Safari and the message came up again. What's more, once that message came up I couldn't make calls anymore either until I restarted the phone! Now I'm back in my apartment and it's as if nothing happened. What gives? I saw a post about resetting the network. Does this happen often to other people?

        Inner exception type: Microsoft.SqlServer.Configuration.Sco.SqlRegistryException
            Message:
                    The network path was not found.
            Data:
              WatsonData = [email protected]rror
    Above message says that your registry is not consistent and some of the parameters are missing from registry.Or
    Account installing SQL server does not have permission to access this. I think case can be here that account with which you logged into your system to install SQL Server might not have certain privileges. Can you take help
    of domain admin account add it as a local administrator in this machine always right click on setup file and select run as administrator. Before this make sure you  remove all SQL Server components from add remove program
    I strongly recommend you to have a good look at below thread
    http://support.microsoft.com/kb/2000257/en-us
    Please mark this reply as answer if it solved your issue or vote as helpful if it helped so that other forum members can benefit from it.
    My TechNet Wiki Articles

  • "Could not activate cellular data network" message after ISO 4.1 update

    I updated my iPhone yesterday just like millions of other people, but since the update was completed, I haven't been able to use the data network. Wi-Fi works without any problems, but when I've been out of the house yesterday and today, I haven't been able to establish any connection to the data network and have received the "Could not activate cellular data network" message each time. Is anyone else having this issue too? So much for a flawless update.

    Hi,
    This happens to me everytime I do a f/w update but for me its for a simple reason and is easy to fix.
    I am using a non iPhone Contract SIM in my iPhone and as such is does not like the default iPhone contract APNs for cellular data, hence the message. These reset when you do a f/w upgrade.
    I have to go into Settings/General/Network/Cellular Data Network and set the APNs (for data and MMS) to ones given to me by my provider, in this case O2 UK for a non iPhone SIM/Contract - all is then well.
    Perhaps you are in a similar situation ?? It shuold be easy to resolve by checking the APNs for your SIM against the ones in the iPhone itself. I found mine by Googling for iPhone O2 APNs. In fact in the end O2 published the setup on their website.
    Hope this helps.
    Radar.

  • Cannot reach PBX system using data network

    Good day Cisco people,
    I am Simon and I have a big situation. My company recently expanded to one of our branches. Now this branch houses 100-150 employees. They are using computers and IP phones.
    Currently, Our voice and data are integrated into one network.( With no configuration for voice and data vlan on the 5 Cisco switches that distributes the broadcast). We have a Cisco 1941 router used for DHCP for our local data lan and for VPN connection to our Head Office, It's network id is 192.168.65.0/24. Then for the IP Telephony we have Avaya 500 v2 for the PBX, It's network id is 192.168.42.0/24.
    Now here is the problem and the questions.
    1. I cannot reach the Avaya PBX from the Cisco Router even though I added a static route from the router. ( Do I need to add the route also from the PBX to the router? I want to add that I don't have any experience in voice networking only in data networking.) And is there a way/or is it possible that I could add a route from PBX to router?
    2. If I am going to configure two vlans on the switches for the data and voice vlan? Do i need to configure router on the stick on the router? How about the interface that the PBX is connected to? what should I configure it? Should I configure it as a voice vlan only? a trunk port? access port?
    3. Lastly, what could be possibly go wrong if ever I configured this on a production environment? And is it that hard to integrate voice with data?
    Thank you for your support. I hope you understand. I don't have experience yet in handling both voice and data. Only data networks.
    Note: Attached also is a simple network diagram for reference. Thank you.
    Have a nice day,
    Simon

    Hi Simon,
    I assume your phones are using static IP addresses to allow them to talk to the PBX?
    If your switches have no VLAN configuration then you will have both layer 3 subnets running over the same layer 2 VLAN.
    You could do a quick test and put a 192.168.42.X IP address on the interface of the 1941 that connects to your LAN, but use the ‘secondary’ option. This means the router will have both a 192.168.65.X address and a 192.168.42.X address.
    You should then be able to PING the PBX from the router.
    You will need to configure either a route or default gateway on the PBX of the 192.168.42.X address you have setup on the router to allow it to route packets between the data and voice networks.
    A better practice idea as you suggested would be to setup a new VLAN for your voice network. You would need to create a trunk link from the switch to your routers inside interface then configure a sub-interface on the router for both VLANs.
    Hope that helps
    Matty

  • How to setup a small office network

    Hello,
    I am looking to setup a small office network comprising 6 G4 macs (existing computers) that have been upgraded to the newest OS version. What is the best way to go about networking these computers together in terms of being able to share files, internet connection, access to peripherals and also implementing a firewall.
    Any suggestions or help would be greatly appreciated.
    Thank you

    1, Get a cable internet ISP account; depending on your service you should be able to secure a 5Mbps down and 2Mbps up on the cable e.g. Cox or Comcast.
    2. Get a good router. The mass market Linksys and Netgear routers aren't very good in terms of reliability. I use a ZyXEL P-330W router is the best I've ever seen. Its reliable and very efficient in terms of throughout. The Apple Airport Extreme is good.
    3. Set up the router to support UPnP. This way all computers will be able to share iChatAV video conferencing. If you enabled "port forwarding" only one Mac would be able to use iChatAV video conferencing.
    4. Set up your router for DHCP to dynamically issue Internet address to all your computers.
    5. Setup the wireless router for encryption such as WPA. This will encrypt wireless communication.
    6. Setup the wireless router for only your computers. You'll have to get the MAC/AirPort ID network addresses as expressed in terms of an xx:xx:xx:xx address. You can get this thru your Systems Preferences -> Network window -> AirPort (in the sidebar) -> Advanced button.
    7. If you have Ethernet in your office then skip steps 5 and 6 above.
    8. On each computer open up the System Preferences -> Sharing and check-off the File Sharing. Set your user access preferences appropriately.
    9. Get a Network enabled All-in-one printer and setup Printer Sharing options. Hook-it up to your network and add your printer by clicking on the "+" sign in your "Print and Fax" Preferences.
    10. Don't enable Apple Firewall on each Mac. The router will be the Firewall.
    Ok. That's the short-hand.. plug it all in and go!

  • Can't view Cellular Data network on legally unlocked iPhone 3GS

    I bought an iphone from Singapore and those phones come as unlock. Now that I am in the States, I was hoping to use my corporate AT&T sim card for data surfing and all. While I am able to make calls, it says that I am not registered for cellular data network. I was able to surf the web using the same SIM on this other HTC phone.
    I was hoping to change the APN settings but that appears to be missing. How can I change the settings to that of AT&T?
    Thanks!

    Do you know the data plan rate your employer is paying for your HTC phone or for whatever phone the data plan is for?
    AT&T's enterprise data plan for the iPhone costs $45/mo.
    Sounds like you or your employer will need to contact AT&T customer support.

  • I had my iphone 3gs unlocked so i could use it in Oz, however although i can phone works ok, i cant get internet, but i the option of Cellular Data Network does not appear with the new sim? Can anyone help pls?

    Hi Just wondered if anyone can help with the above question? I had O2 phone unlocked and bought a local sim card, but although the calls are fine i have no option for internet etc.  I have done searches and got the info details from the sim provider to activate, but  instructions say i go to : Settings; General; Network and then Celluar Data Network, but I dont get that option ?  When i put back my O2 sim card, the option reappears?
    Can anyone help me please? Off to Australia again soon and really could do with it working properly this time.
    Thanks everyone
    Ronnie

    Hi Ronnie, was wondering what brand sim card you bought?
    Was it from Telstra, Optus, Vodafone, Virgin or Mayasim?
    I have a 4 S running iOS 5.01 is there an option in Settings - Network - Carrier? As this should be set to the supplier of the sim card. In my Settings - Network there is no option for Celluar Data Network.
    What version of the iOS are you using?
    Some prepaid sim cards may not have a lot of data, so I suggest searching the companies websites for the best deals before you come here. Telstra usually have good plans. If you take your phone to the shop you purchased the sim card from they will usually set it up for you. 
    Telstra runs on a different frequency to others and offers the best coverage in Australia.
    Just for the record I am not an employee of any mobile company.

  • Data network errors when manually switching from 3g to 2g

    Hi everyone,
    Apologies if this has been posted before but im running out of ideas! - Got my iphone 4 a couple of weeks ago and have noticed a rather irritating problem with it. For some reason, if i manually switch from 3g to 2g the data connection drops.. I get 'cannot activate cellular data network' errors and i have to toggle airplane mode on/off to reset the connection. Is this a network issue? - I live in London and am with Vodafone... Their tech support are useless as all they suggest is resetting the phone or getting it replaced. Its my third handset in 2 weeks and im getting close to calling it a day and sending the phone back to Apple. Anyone out there in a similar situation? - Advice??

    Bump
    So no-one has suffered this issue? - Not even fellow vodafone uk users?

  • X10 not connecting to mobile data networks after upgrade to Android 2.3

    My X10 does not connect to GPRS / EDGE / 3G / HSDPA after the upgrade to 2.3. Wifi is no problem, though.
    I used the SIM card in another X10 with Android 2.1, no problem, got an HSDPA connection. And yes, all the boxes are checked: "Data Enabled" and "Data Roaming";
    I had problems before the upgrade to connect to data networks when roaming, but never in my home network. Now, it doesn't seem to work at all.
    Any advice?

    go to settings -> sony ericsson -> data download
    or
    settings -> wireless & networks -> mobile networks -> access point names -> MENU -> add New -> enter the APN info -> MENU -> Save
    "I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

  • My brother used his Verizon Wireless SIM to activate my factory unlocked iphone 5s.  Now, I can't access the cellular data network option to change APN settings for my new carrier.  Already tried configuration utility and factory resets.

    So as the title says, after I got my iPhone 5s from apple, factory unlocked, my brother used his sim card in it for a moment to allow it to be registered and usable on WIFI until I made it to Japan.  Now that I have a data SIM card, I have to input specific APN settings, which are located in settings>cellular>cellular data network, however, cellular data network is not available as an option. I have reset the phone multiple times with and without backups and with and without the new sim in the phone.  I have also used the configuration utility to try to put the APN settings in the phone.  I contacted Apple and they didn't really have an answer as to what i should do.  My brother checked his Verizon account and my phone does not show up as one of his devices, so right now I'm stuck with and incredibly expensive iPod.  Does anyone have any idea what I can do to remedy this?  I am unable to contact Verizon via telephone myself as I have no phone service.  Any help would be greatly, greatly appreciated.

    You only have to clone your mac when using certain cable modem.  You don't clone your mac when using dsl.
    Greetings from Northern Ontario, Canada

  • Why has my ipad lost connectivity to the AT&T cellular data network after upgrading to iOS 8.1.2?  My iPad is model #MD367LL/A, 32 GB WIFI + Cellular, about 2-1/2 years old.

    Why has my ipad lost connectivity to the AT&T cellular data network after upgrading to iOS 8.1.2?  My iPad is model #MD367LL/A, 32 GB WIFI + Cellular, about 2-1/2 years old. It;s been working perfectly up until now.  I have no problem on my home WIFI, or through personal hotspot working through my iPhone 5.
    I have worked with AT&T, replaced the SIM card with a new one, and done a backup/restore to factory settings, all with the same result that when I turn Cellular
    Data on, with or without Enable LTE, it goes into "searching" mode, or reports "no service".  My iPhone 5 works perfectly on iOS 8.1.2, on Cellular.  I've browsed the blogs and have tried Apple's suggested fix, all to no result. 
    Oddly enough, every once in a while I do get connected to the network for a short ime (minutes), but it always returns to "searching".
    I've filed a report with Apple, along with a request that they contact me, but no results yet.
    Help? (and thank you).

    Hello razmee209.  Thank you for your response.  I spent the better part of yesterday working with Apple Support.  They tried their best, to include backing up photos to my HP laptop, backing up the iPad to iCloud, then resetting the iPad in total.  Same problem.  I restored from the cloud to recover my apps, same problem.
    AT&T installed a new sim card - same problem.  I spent time with AT&T Support yesterday, too.  In both cases, (Apple and AT&T) the support techs who worked with me were extremely polite, courteous and helpful to the best of their abilities, but I think the problem lies deeper, and nobody at Apple is admitting they have a problem with iOS 8, that I'm aware of.
    I didn't have this issue before I upgraded to iOS 8.1.2.
    Everything else with the iPad works fine:  WIFI, Personal Hotspot, email, all my apps, etc.
    In browsing the web for this issue I see that many other folks have the same problem.  I filed a report with Apple this morning, requesting that they contact me, but no word yet.  I was going to go to iPhone 6, and had been considering the iPad Air 2, but I see reports of this problem with those units as well.
    At this point I don't think I'll be spending any more money with Apple, at least not till this issue is resolved.
    Thanks again for your response and suggestions.

  • Data network not working unless i restart my 3g

    i have an iphone 3g on chatr(owned by rogers)
    my data service is active and i also have a voice plan. i had to input certain information in the cellular data network tab in the phone, which i did. every so often the data part of the phone will stop working and give me a message that it cannot connect to the internet and then sometimes it says that im not subscribed to a data network. i am though. i've called chatr and they have resent certain signals to my phone. i've done a hard reset(press and hold both buttons on phone til it goes black and even just turning the phone off) when i do turn the phone off the data will work but then after a while it will stop working again... chatr hasnt been much help at all. their site says the 3g is compatible with chatr and when i call they say sometimes it works and sometimes it doesnt. they registered my imei number, yet it still doesnt work. i have no idea what else to do. my phone is jailbroken on the 4.2.1 OS.i was told that jailbreaking the phone has nothing to do with this problem. i have no idea what to do. i cant keep turning my phone off and on to make the data work. any tips would be greatly appreciated.

    My only suggestion is to post this in the iPhone forums, since this one is for older iPods.
    https://discussions.apple.com/community/iphone
    B-rock

  • HT4623 My new iPad can no longer connect to the 3G network. I keep getting the message "could not activate cellular date network".

    I updated my new iPad to the iOS 6 while connected to wifi. However, it will no longer connect to the 3G network. I keep getting the message "could not activate cellular data network" even though the 3G symbol appears normal. I have tried rebooting, but it still doesn't work. Please help!

    No. You can't

Maybe you are looking for