IW 292: No configurable material can be assigned to th order

Hi,
When I am assigning configurable material in service order as components I am getting as error "no configurable material can be assigned to the order'
If anyone byepasssed the error please let me share.
Regarsd
Sendil

Hi Sendil,
Service and maintenance orders can't handle configurable components. Technically, the service and maintenance order is derived from a PP order. Within a PP-order, configurable components are allowed and they are used to create suborders. An example for that scenario is an order to produce a configurable car: A customer ordered a red car with four wheel drive. So an order is created for a car with (at least) two configurable components: a configurable bodywork (characteristic is "Red") and a configurable drive (characteristic is "four wheels"). After entering these components, two suborders are to be created because the bodywork and the drive have to be produced, too.
This is standard, and unfortunately it will not be changed within the
next releases. Message was introduced with note 72404.
Regards
Amber

Similar Messages

CS-No configurable material can be assigned to the order

Hi,
Can someone please assist me with the following problem? I am creating a Refurbishment Order in Customer Service using an Equipment created by an action in VMS. The material maintained in the Equipment is a configuration material and I get an error "No configurable material can be assigned to the order" when I use this equipment to create the order.
Your assistance is highly appreciated.
Regards
Vogie

Dear Tiaan,
We have exactly the same issue. Apparently SAP has blocked this posibility. The SAP solution doens't support configurable materials on Service Orders goes for 4.6, 4.7 and 6.0. To my understanding this is a very big miss in the SAP solution. I hope that we by listing it here can inform SAP that it makes no business sence not to be able to provide service on configurables materials. We will most likely go for a modification in the source, since SAP doesn't support this.
Best Regards
Klaus

Configurable Material as BOM component in SALES Order BOM

Hi Gurus
I have following
1. Material ABC is a configurable material (variant)
2. BOM of this ABC has further configurable materials
Is it possible to maintain requried charasterstic of the compoents which are configurble at the time of SALES ORDER BOM CREATION.
If yes, how. please explain.
Thanks in advance
sunil

Dear Sunil,
Please refer to the following link:
http://sap-img.com/sap-sd/sales-bom-implementation.htm
I will suggest you to visit http://sap-img.com/sap-sd.htm. It will give you the overview of SAP SD module.
Moreover there is a separate section of FAQs with answers which will help you in great deal.
Do let me know in case of any queries.
Hope this helps you.
Do award points if you found them useful.
Regards,
Rakesh

How an AUC asset class can be assigned to internal order type

Hi
We want to create new AUC asset class for our requirement. For that purpose we want to use existing internal order type of my new AUC asset class also. When we create internal order in KO01 and create AUC in same step new asset class should be picked up. Please explain me how we assign internal ordet type to AUC.
Regards
Padma

Hi Padma
Do the following configuration steps for AuC scenario.
1. Asset under Construction
1.1 Define Screen Layout for Asset Master Data
IMG Investment Management Internal Orders as Investment Measures
Master Data Assets under Construction Define Screen Layout for
Asset Master Data
1.2 Define Asset Classes
IMG Investment Management Internal Orders as Investment Measures
Master Data Assets under Construction Define Asset Classes
2. Asset under Construction
2.1 Define Model Orders
IMG Investment Management Internal Orders as Investment Measures
Master Data Orders Define Model Orders
2.2 Define Order types (KOT2_OPA)
IMG Investment Management Internal Orders as Investment Measures
Master Data Orders Define Order Types
2.3 Define Investment Profile and Assign
IMG Investment Management Internal Orders as Investment Measures
Master Data Define Investment Profile
3 Settlements
3.1 Maintain Allocation structure
IMG Investment Management Internal Orders as Investment Measures
SettlementMaintain Allocation Structures
1.2 Maintain Settlement Profile
IMG Investment Management Internal Orders as Investment Measures
SettlementMaintain Settlement Profile
3.3 Maintain Number Ranges for Settlement Documents
IMG Controlling Internal Orders Actual Postings Settlement
If you want budgetary control also do the following steps:
3 Planning and Budgeting
3.1 Maintain Planning Profiles
IMG Investment Management Internal Orders as Investment Measures
Planning and Budgeting Maintain Planning Profiles
3.2 Maintain Budget Profile
IMG Investment Management Internal Orders as Investment Measures
Planning and Budgeting Maintain Budget Profile
3.3 Define Tolerance Limits for Availability Control
IMG Investment Management Internal Orders as Investment Measures
Planning and Budgeting Define Tolerance Limits for Availability Control
Regards
Kiran

Production order without referance to sales order in configurable material

Dear all,
I am trying to create a production order for a configurable material. I dont have a sales order for that. And I can not even create a sales order for some reason.
While creating a production order the system asks for a account assignment (either a sales order or WBS).
The error which comes while creation is ,
Standard production only allowed with ref. to indivual customer stock
Message no. CO542
Diagnosis
Direct order creation for a material to be configured is only possible if it takes place in relation to sales order stock since a configurable material only allows production for sales order stock. A sales order or a WBS element can serve as sales order stock.
Procedure
You should enter a sales order or a WBS element for account assignment.
How to solve this.
Thanks in advanmce.
Sumeet

Hi
1.Create a CIR with transaction with md61
2.You will get a reference number
3. with that reference number you will be able to create a Produ tion order.
check and let us know if you have any issues
reg
DsK

Fico configuration material

Hi,
I need fico configuration material .can anyone mail it to me on my mail id [email protected]
thxs
sapna

Hi
You can find the fi config steps insap-img.com
Nevertheless , Iam hereiwth giving you the basic fi configuration, this will help you to some extent
List of the Basic 24 Steps for FI configuration.
1.define company
2.define company code
3.assign company code to company
4.define business area
5.define fiscal year variant
6.assign fiscal year to company code
7.define posting period variant
8.define opening & closing posting period variant
9.assign company code to posting perid variant
10.define number ranges
11.define tolerance limit for employees
12.define field status variant
13.assign company code to field status variant
14.define chart of accounts
15.assign company code to chart of accounts
16.define retained earnings
17.define tax procedure
18.assign country to tax procedure
19.enter global parameters
20.define account groups.
21.define document numbers ranges
22.edit chart of account list
23.define open posting period varient
24.assign company to field status variant
Thanks
Aravindan.M.R

BAPI/FM in ECC to create a sales order with variant configurable material

Hi all,
I need to create a function module that creates a sales order in ECC with a variant configurable material.
can some one tell me if there is a in built function module or BAPI that i can make use of to create a sales order with variant configurable material in ECC.
Regards,
Jessica Sam

Thanks MxG,
I dont know how to use this BAPI. .Can you suggest me a sample code.
My reqmnt is, i have
Sold to party, ship to party, bill to party , VC config material and all char values that should be populated while creating a sales order.
please help me with what values should i populate in i/p paramters and and how to use this BAPI with some sample code if posible.
Regards,
Jessica.

Problems during filling of the material which is assigned to REAL_SUBs

Hello everybody,
During the filling(DGE5) with the materal which is assigned to several real substances(each real substance has a reference to a substance of dangerous goods classification), there is a problem coming out.
When I checked the filling logs, it shows:
" Material 200-270 is assigned to several real substances
Message no. DGA412
Diagnosis
You attempted to fill data records in the dangerous goods master with data from data records in specification management.
However, the material 200-270 is assigned to several real substances.
System Response
The material 200-270 is not filled.
Procedure
Ensure that the material-real substance assignment is unique and start filling again."
I did the assignments according to the information here: http://help.sap.com/saphelp_45b/helpdata/en/3e/60957d0d1311d286e7080009b98822/frameset.htm
" Filling the Dangerous Goods Master "
and " DG Classification (Classification Key) "
Here says, the material-real substances assignment can be m:n relationship. (If I understood correctly)
I'm quite confused now. Who can help me?
Regards,
Li
Edited by: Li Cheng on Mar 30, 2010 12:00 AM

Hello Jayakumar,
I know what you said " For DGfilling to work -- One material should be linked to one REAL Substance " is in accordance with the truth which I've met.
But I still don't understand what " SAP Online Help " describes:
http://help.sap.com/saphelp_45b/helpdata/en/3e/60957d0d1311d286e7080009b98822/frameset.htm
" DG Classification (Classification Key) "
" The realationship between material and REAL substance is m:n "
Is this realationship carried out using material-substance assigenment?
Just like what another " SAP Online Help " page describes:
http://help.sap.com/saphelp_45b/helpdata/en/3e/60957d0d1311d286e7080009b98822/frameset.htm
" Filling the Dangerous Goods Master "
"Assignments between materials and substances of substance category Real substance or Dangerous goods classification are carried out using material-substance assignment. "
Is that means, one material can be assigned to several REAL substances with have their own reference of Dangerous Goods Classificaiton (the realationship between REAL substance and Dangerous Goods Classification is 1:1 ) ??
Thanks a lot!
Li

About configurable material

hello,
any body pls explain me. i am facing to issues pls provide me solution
1) my scenario is make to order with configurable material.
when i am creating sales order in configuration i have maintined characteristic which were mainly required and status is showing green but when i am going to save it showing inconsistency check message and showing the same material again and asking for enter the data.again means it showing twice then only its allowing to save. i dont have any sales order BOM i have only PROD BOM and component is recursive.
2) i have maintained dependency in BOM.
dependy is procedure.
formula is $self.qty = width*thickness.
when the time of check i didn't get any error and released.
but when MRP run i haven't get result on base of my dependency. just which qty i have maintained in BOM only i am getting. pls suggest me where i am doing wrong. actually now we r in GOLIVE.
THANKS & REGARDS
Bhakta

thanks for ur reply
actually i have maintained dependency formula mentoined below
Z_WOOD_CROSS_QTY:
10$self.z_QTY_JSSL = (((((32.5(WIDTH/25.4))/(121212))6)
20 NO_OF_Pallets))
30 if packing = 'hisexp' or packing = 'ownexp' and length > 3000,
40$self.z_QTY_JSSL = (((((32.5(WIDTH/25.4))/(121212))5)
50 NO_OF_Pallets))
60 if packing = 'hisexp' or packing = 'ownexp' and length > 2000
70and length <= 3000,
80$self.z_QTY_JSSL = (((((32.5(WIDTH/25.4))/(121212))4)
90NO_OF_Pallets))
100 if packing = 'hisexp' or packing = 'ownexp' and length > 1000
110 and length <= 2000,
120$self.z_QTY_JSSL = (((((32.5(WIDTH/25.4))/(121212))3)
130NO_OF_Pallets))
140 if packing = 'hisexp' or packing = 'ownexp' and length <= 1000,
150
160$self.z_QTY_JSSL = (((((32.5(WIDTH/25.4))/(121212))3)
170NO_OF_Pallets))
I have maintained
Thickness: 0.6mm
Width:1250mm
Length: 2010
When I am doing MRP run it should consider line 40-70
But it considering line 80 - 110 only
Its giving result as 1.64 in place of 2.04
Pls help me to resolve this issue. .
THANKS & REGARDS
CH.Bhaktavatsalam

Assignment of production order to network

Hi,
How can we assign a production order to the network or vice versa.
I know the WBS can be assigned to production order through assignment tab in production order.
Thanks,
Santhosh

Thanks for your response
however while creating the planned order iam encountering the below message
"Account assignment category N invalid"
Message no. 61143
suggest me which planned order profile to be used while creating planned order with transaction MD11
Please also explain me where to assign the network in production order
Thanks,
Santhosh
Edited by: SANTHOSHCH on Aug 14, 2010 8:56 AM

Assigning of Prodn Order

Hi Experts,
Can we assign the production order to the particuler employee?.
If yes, how?.
Can we get the details about production orders which is assigned to the particular employee?.
If yes, How?.
Please explain me.
thanks,
Vijay.

Hi mani&febi,
Thanks for your clear ideas.
It is giving clear picture.
thanks,
Vijay.

Can anyone say me the Configuration material for the ECC 6.0 FI/CO

Hi everybody
Can anyone say me the Configuration material for the ECC 6.0 FI/CO
thanks n regards
venuprasad

Hi
please refer
http://www.sap-img.com/
http://www.surya-padhi.net
hope this helps
pushkaraj

Equipment configuration data can't be deleted?

Hello fellow EAM friends,
I have putted in the equipment tabpage a configurable material. However this was not correct. Now I want to delete it. Unfortenately it is greyed out, so I can not delete it.
What would be the process to get the configurable material number be deleted from the view. I already checked the customzing of the fields.
Thanks in advance for your answer in this.
Regards,
Pascal

Hello Pete,
I have done some testing. I created a simple material which is configurable. No object dependencies are vailable.
The moment I add that material in the config view of the equipment and save the equipment, I can still delete the material which is mentioned in the equipment.
However, the moment I choose a characteristic value, the field turns grey, and cannot be deleted. Even if delete the assigned value in the configuration, the fields stays grey.
It seems the moment the field EQUI-CUOBJ has a value, you cannot delete the material entered.
I supose it is standard SAP. I wiill look in notes if I can find something.
Kind regards,
Pascal
Edited by: Pascal Posthuma on Sep 20, 2010 12:09 PM

Issue in consumption of forecast for configurable material

Hi,
we have a issue in consumption of forecast by sales order for a configurable material.
Please find the below details for the settings maintained and the steps followed.
Please let me know how we can overcome this issue.
settings in R/3
1. Class and characterisitcs are created in R/3
2. standard material was created and class assigned
3. planning strategy used is 56
4. material, class, characteristics,ATP check, ATP customizing , sales order were integrated to APO
Settings in APO
1. CBF table, CBF profile, Consumption group were created in APO
2. Consumption group is attached to the product master
following steps were followed.
1. Forecast was created in DP for a certain characterstics ansd relaesed to SNP/PPDS
2. forcast is visible in product view
3. sales order was created in R/3
4. slaes order is visible in APO but it is not consuming the foreacast for the same set of characteristics.
Please let me know how we can overcome this..are we missing any customization ...?
Thanks
Ram

Hi Srinivas,
thanks for your response.
The forecast consumption problem was solved after correcting the entries in requirement strategy.
have one more query.
when the sales order for a configurable material is transferred from R/3 to APO, we should be able to see the values under "descriptive characteristics tab" in APO product view.(when we click on the green triangle representing the configuration).
However, we could see the values under "descriptive characteristics tab" for some of the characterisitcs and not for other characteristics.
we tried comparing the characteristics but could not figure out the reason.
any pointers / clues to come over this issue would be helpful.
thanks
Ram

Error message while creating configurable material for variant configuration.

Dear All,
I want to create configurable material for the purpose of variant configuration. When trying to create configurable material using mm 01 or mm k1, it is displaying an error message that internal number assignment is not possible for the material type configurable materials as well in using external number also. Can anyone specify the steps to be done in creating the configurable material. Thank you all.
Regards
Akula Sivaji Kumar Madhu Kiran

If you want to set these material type to another group (Which has a internal number and external number range), then you can do it.
In MMNR, Click on the Edit Group.
Then select the material type and click select element.
Then mark a tick option in another group and then press Element/Group.
Then you can see the material type will come under this group.
Now save your entry, and create a material with this material type.

IW 292: No configurable material can be assigned to th order

Similar Messages

Maybe you are looking for