IWeb continuously does not respond to commands.

iWeb continuously does not respond to commands and I end up having to force quit. I cannot update my website, I can't do anything with iWeb anymore. What should I do? Help!

Try the following:
delete the iWeb preference file, com.apple.iWeb.plist, that resides in your Home() /Library/Preferences folder.
go to your Home()/Library/Caches/com.apple.iWeb folder and delete its contents.
launch iWeb and try again.
OT

Similar Messages

My aux input does not work. When i put in my headphones my mac does not respond, and my speakers just continues as normal. What to do?

My aux input does not work. When i put in my headphones my mac does not respond, and my speakers just continues as normal. What to do?

I had the same issue. Initially i thought i need to take it to apple for replacing the aux port. But luckily I was able to fix it by resetting the PRAM . To reset the PRAM
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Immediately press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.Continue holding the keys down until the computer restarts, and you hear the startup sound for the second time.
Release the keys.
Resetting PRAM may change some system settings and preferences. Use System Preferences to restore your settings.
You can try this before you take to apple store. It may work if you are lucky. Good luck

" device does not respond to is base address, do you want to continue ?" OR " Le périphérique ne répond pas à l'adresse de base"

Environment :
NI-DAQ 6.9.3
PCI-6025 E Card
LabPC1200 Card
PCI serial interface card
AGP video Card
Measurement & Automation explorer 2.0
After using the PCI-6025 E during an hour with the Measurement & Automation explorer 2.0 software, the message :�Le périphérique ne repond pas à l�adresse de base, voulez vous continuer?� or « the device does not respond to is base address, do you want to continue ? »
All the informations , even in the System Configuration Panel, seem to be in order. It seems that the problem occurs after I have tried to use also the Lab PC 1200 by the way of the Measurement & Automation explorer 2.0.
I have tried to:
� restart the software,
� stop the PC and restart it after a while,
� uninstall NI-DAQ 6.9.3 and all NI softwares
� Install NI-DAQ 7
The same problem was always here.
� stop the PC remove all the Cards except the video card
� restart the PC
� stop the PC and put only the PCI-6025E Card
The same problem was always here.
� uninstall NI-DAQ 7 and all the NI softwares
� stop the PC and remove the PCI-6025E Card
� Install NI-DAQ 6.9.3
� Stop the PC and install the PCI-6025E Card in another PCI Slot.
The same problem was always here.
I have each time try to change the number of the card by the use of Measurement and automation explorer 2.0 but with no success.
How can I do to use again this card?
I really thank you for any response.
NICOLAS Gabriel.

Hey Nicolas,
Try opening up the Reset Device.vi inside of LabVIEW and execute the VI. All you have to do is set the correct device number and check that the error returned is 0 and not another error number. In many cases a crashed program can cause the devices to enter into an unsafe state that they need to be reset from.
It is possible that you damaged the device and that it will need to be sent in for repair, but in most cases a reset will fix the issue. Also, try opening up MAX and right-click on Traditional NI-DAQ Devices under Devices and Interfaces and click on reset Traditional NI-DAQ. If that doesn't work try the Device reset under DAQmx as well.
I hope this helps out.
Joshua P.
National Instruments

HT1343 shutdown dialouge box is open, mouse does not respond, command keys do not respond, how to restart?

shutdown dialouge box is open, mouse does not respond, command keys do not respond, how to restart?

Hold the power button down for an extended amount to force quit. .

Recently my track pad (in my Mac Book Pro) does not respond to 'clicking' commands.

Recently my track pad (in my Mac Book Pro) does not respond to 'clicking' commands. It does just fine with a USB cable mouse. What do I do?

Are you tapping to click or physically clicking? If you're clicking, does the trackpad button go down all the way?

My screen does not respond to any touch commands on new 4S

The screen on my new 4S does not respond to swiping in order to configure. In addition, when I try to turn it off, it will not respond to cancel or swiping. I have tried to reset to no avail. Is there something else to try?

Try a reset:
Hold the Sleep and Home button down for about 10 second until you see the Apple logo.

I am suddenly unable to open mail from the dock. dock shows mail is up and running, but stamp does not respond when clicked, and will not quit. help?

I am suddenly unable to open mail from the dock. dock shows mail is up and running, but stamp icon does not respond when clicked, there is no mail window opened, and will not quit. when double clicked, get new mail is not an option and I get no response with other actions.
I am retrieving mail on my phone with no problem. this just began happening, no updates or problems with anything else.
help?

command-option-esc keys and force quit Mail. Then relaunch.

Customize toolbar does not respond.

I was trying to add and remove some icons on my safari toolbar and found out that it no longer responds. I cannot drag and drop icons, or remove icons. The only thing that I can do is right click on an icon and "add icon" but as far as removing them it does not respond. Can somebody help ?
Thank You

Have you tried restarting or running Disk Utility/Repair permissions? You may need to delete the .plist from your user folder. Hold down the option key and use the Go To Folder command from the Finder. It should reveal you user library.

IMac A1311 does not respond to any keyboard or mouse

Hello,
My iMac A1311 does not respond to any keyboard or mouse.
I can restart it. It starts without a problem, but I can't enter my account password or move the cursor.
I have tried using four different keyboards including the original bluetooth keyboard and mouse, an Apple wired keyboard, a generic wired keyboard and a wireless keyboard. I also tried resetting PRAM as well as NVRAM. I even tried to start it in Target Mode and tried to start it with a start-up disk (The disk remained inside the computer). Unfortunately, it all seems to originate with the same problem. The computer does not recognize the mouse or the keyboard. I believe I could rule out a problem with the USB port since the original keyboard/mouse uses Bluetooth.
Any suggestions would be greatly appreciated.
Thanks in advance...

Is this a wake from sleep problem, or after only after a restart?
If it is a 'wake from sleep' issue then since some point in OS X 10.6.x, through 10.7 and 10.8, some users (me included) seem to have the occasional problem with the Mac being unresponsive to any commands from the keyboard/mouse/trackpad, and the issue seems to be something to do with Bluetooth not fully waking from sleep.
The 'fix' that works for me 100% of the time is to go to System Preferences>Energy Saver and set 'computer sleep' to 'never'.
I keep hoping that an OS software update will come up with a 'proper' fix.

Nano was working perfectly until I had to reformat for windows computer. Now, it does not respond well to touch.

I recently purchased a ipod nano and briefly had it synced with my macbook pro. I recently sold my macbook pro and had to reformat ipod nano. Since then, the ipod nano does not respond very well to touch commands and sometimes goes into apps that I did not select. It is impossible to switch from page one to page two one app screen.
Thanks,
acdc1996

Hey acdc1996,
Welcome to Apple Support Communities! Even if you have a different generation of nano, you'll want to check out the troubleshooting steps in the following article as most of them would still be applicable:
iPod nano (6th generation): Hardware troubleshooting
http://support.apple.com/kb/TS3474
Have a great day,
David

ITouch will reset, but device does not respond to touch

I'm trying to reset my iPod Touch. I am able to turn it off by, pressing and holding the Sleep/Wake button and the Home button together until the Apple logo appears. but I can not get past the Apple logo as the touch screen does not respond. When I connect the device to iTunes I get the message you must unluck your itouch and the screen on the iTouch goes from the Apple logo to the "Connect to iTunes" screen. At no point, when the Apple logo or the "Connect to iTunes" appear does the device respond to touch the screen. The iTouch is fully charged.

If it's showing the 'Connect to iTunes' logo but iTunes is asking you to enter the Passcode you will need to pop the device into a Forced Recovery state.
To do this, connect the device to the computer via USB, once connected make sure iTunes is open. Hold down the Home & Power Button together until the device resets (Apple Logo on screen), as soon as you see this remove your finger from the power Button but continue to hold the Home button. You should then see a prompt in iTunes stating 'iTunes has detected an iPod in recovery mode, you must restore to continue' at which point you will want to follow the prompts to restore the device.

My IPHONE 4 toggle button does not respond sporadically. What's the fix when this happens?

My IPHONE 4 toggle button does not respond sporadically. What's the fix when this happens?

This is the official troubleshooting doc that covers that issue:
http://support.apple.com/kb/TS2802
The relevant steps are:
The Home button is slow to respond
If the Home button is slow to respond when exiting one application, try another application.
If the issue exists only in certain applications, try removing and reinstalling those applications. For further assistance in installing and troubleshooting applications see this article
If the issue continues, Try turning iPhone off and then on again. If the iPhone will not restart, try resetting it.
If the issue is still happening, try to restore the iPhone
Seek service is the issue is still occurring.

Finder does not respond/Booting troubles

Hi!
MacBookPro 13.3" (2010)
Snow Leopard 10.6.8
A couple of days ago I started having trouble with my MBP. Finder stopped responding. The first sign if I remember correctly was that when I tried to shut it off nothing happened, so I went to Force Quit activities and restarted Finder and the computer shut off. I didn't think of anything specific at the time. Now however when it boots Finder won't respond, no matter how many times I restart it. I have tried restarting it through Force Quit, through the dock and a Terminal command that i found ("kill -HUP `ps auxc | grep Finder | awk '{print $2}'`" from here). When I boot, as said, it does not respond, I don't get my icons on the desktop or anything. I can however use other applications without troubles. I have not tried saving anything but I have experienced troubles with the internet (however that might not be related) but when I try to aquire mail I can't (but that might also be related to troubles with internet (although I've been connected at the time and not only to the network). I have tried booting in safe mode and that has not helped.
I also tried doing software update because I thought that maybe a previous one messed something up (I have read that has happened to some people). That did not work or help. It downloaded some Java updated, iTunes, Printer updates and so on and a safety update and it went to installation mode and an error message popped up (I can't remember what it said but as far as I remember it only said there was an error, I sent it to apple). I tried again when I managed to boot it and as I suspected it would it said it could not save the files anywhere.
I have however also experienced booting problems, both in safe mode and normal. When I boot, a bar appears at the bottom of the screen. Sometimes it takes about a minute or more longer that normal and sometimes it won't boot even after 10-15 minutes (then I force it off by holding down the startbutton).
I've looked for different discussions here but haven't really found what I have been looking for, at least that has helped.
/chipshooter
I would really appreciate help, Thanks!

You have a hardware problem. More then likely the drive is failing or it could be the cable going from the drive to the logic board.
Soon it will not boot at all. That is when the drive has failed completely.
Copy you personal data to an external ASAP.

Problems with Tomcat Server : Does not respond (Sometimes) - Plz Need Help

I have a web application running on Tomcat 4.1.31. (SUN/Solaris)
Clients access through iPlanet Web Proxy (SUN/Solaris).
Theres a class that build a generic form (it return html codes) then it's affected in the JSP page :
MyClass class = new MyClass();
<%= class.getHtmlCode() %>
the size of the form is variable (100Ko to 1,5Mo)
When i m using the proxy, sometimes the server does not respond when he do the affectation <%= class.getHtmlCode() %>.
If i call the page without proxy it work.
The problem seem not depending of the size of the form. Without proxy it always work. And with proxy sometimes the server does not work.
Please need help

Originally Posted by scum
Hey All,
Need some help with ZDM7 PXE preboot services.
Currently running a netware 6.5 server in VLAN1
PXE client sitting in VLAN2.
DHCP Server is running on VLAN3
IPHelper is running
DTS.ini, PDHCP.ini and TFTP.ini are unmodified.
I have had networks put an IPHelper in place and my client successfully picks up an IP address. The screen displays the "BOOT SERVER IP" correctly and the clients IP details are correct.
I watch the top of the screen where the Timeout counts down and eventually gives this error.
"Error: The server did not respond as requested in time
ZENworks shutting down...
Press any key to continue..."
This happens on every machine i have tested. If i hold down the Ctrl+Alt keys, then the imaging menu appears, i can select maintenance and the client will pull down the initrd, etc.. fine.
if i disable the IPHelper, move the client to the same VLAN as the server, then the whole process works perfectly.
not sure where to go from here.
help please ;)
leon
Hi Leon,
If you are getting the ZENworks menu when holding down the Ctrl-Alt keys, PXE/PDHCP seems to be doing the right thing. Routing issues also don't seem the case as you can pull down the first PXE boot files....
The server running PXE, I assume it also runs the TFTP and Imaging services?
These services are also running a recent version of Zen 7 (IR3/IR4)? A little more info on these components and what server they are on would be good :)
Cheers,
Willem

Hello The problem appeared two days ago is that I can't open my mail app. everything was fine and functional. Now I double click on the icon and it does not respond. it receives mail and I can see push notifications on the mail icon but when I try t

hello
The problem appeared two days ago is that I can't open my mail app. everything was fine and functional. Now I double click on the icon and it does not respond. it receives mail and I can see push notifications on the mail icon but when I try to open it is no use. OS Y 10.10.2 (14C1514)

Please follow these directions to delete the Mail "sandbox" folder.
Back up all data.
Triple-click anywhere in the line below on this page to select it:
~/Library/Containers/com.apple.mail
Right-click or control-click the highlighted line and select
Services ▹ Reveal
from the contextual menu.* A Finder window should open with a folder named "com.apple.mail" selected. If it does, move the selected folder—not just its contents—to the Desktop. Leave the Finder window open for now.
Restart the computer. Launch Mail and test. If the problem is resolved, you may have to recreate some of your Mail settings. Any custom stationery that you created may be lost. Ask for instructions if you want to preserve that data. You can then delete the folder you moved and close the Finder window.
Caution: If you change any of the contents of the sandbox, but leave the folder itself in place, Mail may crash or not launch at all. Deleting the whole sandbox will cause it to be rebuilt automatically.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.

IWeb continuously does not respond to commands.

Similar Messages

Maybe you are looking for