IX-2 losing connection on Transmission bittorrent client

I have set-up my IX-2 for RAID 1.
No problems for over a week using bittorrent client transmission.
However, since the weekend, it is starting to lose connection with the error "Connection FailedCould not connect to the server. You may need to reload the page to reconnect."
With my limited IT knowledge, I have checked my router and IX-2 has an open port and the settings in transmission have confirmed that the port is open. Even changing port numbers doesn't help.
Can anyone help please?
Thanks

Hello trevorsem
Are you seeing the connection error when connecting to the web interface locally or remotely?
Are you using personal cloud to access your unit remotely or using your public ip address?
Also could I have you send a screen shot of the port settings you are looking at for transmission as the transmission
client in the ix2 firmware should not have those level of settings.
Are you using public or private trackers for your torrent downloads? Public trackers should work fine, however most private trackers require specific torrent clients and configurations to properly download from the tracker.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Similar Messages

WRT350N Losing connection with web browser after running Bittorrent client

My Setup:
HP Pavillion Dual Core Desktop PC 2GB Memory
Windows Vista Premium Home
Linksys Wireless WUSB G Adapter for my destop
Time Warrner Cable Modem - Webstar Model
I have had a WRT54G for a long time, and it has been flawless, I decided to buy a Refurbed by Linksys WRT350N because I anticipate getting a new device and devices that will use the Draft N Standard. Anyhow, I have it set to narrowband to use ONLY Wireless G, have it set up as i Did with my G Router to use WEP with Broadcast SSID ETC ETC, opened up all the same ports forwarded on it and made all same settings as in my WRT54G.
Here is the problem:
I typically use a Bittorrent client to download large files to my computer, specifically UTorrent. With my WRT54G I would get good speeds but even after a couple of hours I would still be able to start my Browser, IE or Firefox 3 and get, albeit slow, but still get my webpages to render.
Now when UTorrent runs for a couple of hours with my WRT350N I load my web browser and I get a message that says "Cannot connect" or connection is timing out. Sometimes it will load the page but looks more text like than HTML, and I attribute that to packet loss?
Anyhow I did use Linksys Tech Support, and they suggested I changed my MTU to a lower setting instead of Auto which I did and it didnt make a difference, welL i shouldnt say that I do get forecastfox to load on FIrefox where it didnt load before and sometimes I get the non html version of the pages to load.
Any help would be greatly appreciated, I am patient and LOVE a project and I have a feeling this is going to be one.

Actually that is what I was doing last night and got a bad flash and bricked my router..so its on its way back to Linksys...

Recent problem: clients are losing connection to AMS 5.0.1

For the past week, since Oct 14, we've been having issues with clients losing connection to our AMS application. We have online classes that include a chat room and sometimes an audio stream from the instructor. This application and its server has been running stable for months... until last week.
One of our staff was connected to the app, getting everything set up for a class, and she started complaining of getting disconnected. I looked in the application logs and noticed that the application.onDisconnect was being triggered. However, the client didn't register that it had been disconnected for several seconds afterward. She let me know when she got the "Diconnected" message on her screen, which comes from the NetConnection.onStatus handler.
The only other sign of a problem is that in the server's core logs we started getting the following error when we checked bandwidth:
> Invalid command message data: unexpected bw response from client 000000001D670170
The client number changes frequently, so I'm guessing that this is first happening to one person and then another. We don't think that this bandwidth check is causing the disconnects because we rolled back to a previous version that didn't have it. The disconnects still happened after using the old version. What makes it frustrating is that it hasn't happened to anyone on the dev team, regardless of which network we've connected from. Also, the code hasn't changed on the client or the server, and to my knowledge, we're still using the same configs for months.
The AMS is v5.0.1, the client is written is AS2 and targets Flash Player 11.4.
The affected Flash Players reported are 15.0.0.152 and 15.0.0.189, in browsers IE, Firefox, and Chrome, but not all installations are affected.
Is there anything else I can look at to determine what the problem is? Does anybody have any insight as to what might be suddenly affecting our AMS app?
Many thanks,
Nick

Yes, we came to the same conclusion about the unexpected bw. We realize that it is not causing the issue, but I included it because it started happening at the same time and thought that they might be caused by the same issue.
We have been trying to come up with what changed to cause this, and aren't coming up with anything.
We have been on 5.0.1 for at least 5 months, no changes there.
We haven't updated the main.asc since 9/16.
The VM that runs our server is still the same, and AMS config files haven't been touched.
The client swf had a change 2 weeks ago, but we've reverted the change and are now using the old swf again.
The person who initially reported the problem was using the same computer that she's used many times to connect; she was going through her usual process to set up for the session.
You mentioned bad network, and that is another thing that I have been looking into, but our IT department says that we haven't seen any huge increase in bandwidth usage, and that everything looks to be within normal operating ranges
If there are any other points that you can think of that I could check for changes, I'm open to suggestions. This problem has been ongoing for 6 days, and I have been searching for answers since it started.

Torrent problems/losing connection

After about 30 min-1 hour I lose my internet connection if I'm using any bittorrent client (usually Azereus, sometimes Bitcomet). If i don't have a client open, my internet stays up for days. I know that it isn't my cable modem, as I can leave my computer downloading for days without losing my connection.
When I lose connection, I have to unplug the modem and router to get my internet back. Sometimes I have to reset the router and go through setup again to get it back.
Do I need to limit my download speeds? I can't figure out why this is happening. My card works fine. I go to hotels or friends house's and I don't lose connections.
I'm using the WRT55AG router, V1 I think. On charter cable internet with a Dell Inspiron E1505 LaptopMessage Edited by necrochaos on 03-31-200712:40 PM

The router did stay up longer after changing the number of connections, but it still went down after a few hours.
This is a wireless connectionMessage Edited by necrochaos on 04-04-200703:34 AM

Windows 8 keeps losing connectivity

Hi, not sure if this is unique but for the past few weeks Windows 8 has been losing connectivity every few minutes when browsing web pages, playing games etc. I am sure it's windows 8 as I have another work laptop using XP that I can be on all day via a
VPN and that does not drop at all (it would normally drop within a few seconds of losing connectivity). I've done a lot of searching on the net for the same issue, others seem to be having similar things happen such as slow speed but can't find anything that
matches, hence this separate question.
I have also tried swapping routers to no avail. The thing is, you wouldn't know anything had happened from the network connectivity. Suddenly a page won't load. The wireless connectivity at the bottom right of the screen shows a full 5 bars (not limited
connectivity). The way to get it back again is to leave it for a few minutes or disconnect from the router and reconnect again. Even whilst typing this I have had to do that twice.
I'd appreciate some suggestions!
Many Thanks, Paul.
PS... IPCONFIG/ALL shows...
Microsoft Windows [Version 6.2.9200]
(c) 2012 Microsoft Corporation. All rights reserved.
Wireless LAN adapter Local Area Connection* 17:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Microsoft Hosted Network Virtual Adapter
#3
   Physical Address. . . . . . . . . : 56-DE-2B-64-0B-25
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
Wireless LAN adapter WiFi 2:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Qualcomm Atheros AR5B125 Wireless Network
Adapter
   Physical Address. . . . . . . . . : 74-DE-2B-64-0B-25
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 192.168.0.4(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : 11 May 2013 10:31:15
   Lease Expires . . . . . . . . . . : 12 May 2013 10:31:21
   Default Gateway . . . . . . . . . : 192.168.0.1
   DHCP Server . . . . . . . . . . . : 192.168.0.1
   DNS Servers . . . . . . . . . . . : 194.168.4.100
                                       194.168.8.100
   NetBIOS over Tcpip. . . . . . . . : Enabled
Ethernet adapter Local Area Connection:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Broadcom NetLink (TM) Ethernet
   Physical Address. . . . . . . . . : DC-0E-A1-07-A8-F0
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{A319BEA5-A55C-4E0C-AF67-922BEBD4C7BB}:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Microsoft ISATAP Adapter
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 13:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
   IPv6 Address. . . . . . . . . . . : 2001:0:9d38:953c:3483:1732:adda:66e3(Pref
erred)
   Link-local IPv6 Address . . . . . : fe80::3483:1732:adda:66e3%14(Preferred)
   Default Gateway . . . . . . . . . : ::
   DHCPv6 IAID . . . . . . . . . . . : 436207616
   DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-16-28-39-CC-DC-0E-A1-07-A8-F0
   NetBIOS over Tcpip. . . . . . . . : Disabled

Hi,
Does this issue occur with both wireless and wired?
I suggest to perform these tests to troubleshoot the issue:
1 Update NIC card for your machine
2 Temporary disable firewall and antivirus program
3 Logon with Safe Mode with Networking
4 Update framework for your router.
Leo Huang
TechNet Community Support

Network Drives Losing Connection from Server 2012 to Windows 7 64bit Machines

I have about 20 users at my facility and recently upgraded our server from one running server 2003 to one running server 2012. Since that occurred, I have had numerous issues that I did not encounter on the old server.
Lately, users have been losing connection to the shared network drives randomly and constantly. The drives will come back on-line on their own but it could be 2 minutes or 30 minutes before they do and when users are in the middle of working on a document
from the network, they are unable to save until the drive comes back. Manually disconnecting and re-mapping them works sometimes but then the problem will re-occur. I have tried re-doing the shares and security settings and run a couple of supposed hotfixes
on the client side and the server side to no avail.
Now our regional office is suggesting that I re-connect the old server and then rebuild the new one with server 2008 r2, something I would like to avoid if possible.
I feel like this is a simple setting that I am missing, no conditions have changed except for the new server.
The server is a Intel Xeon CPU E5-2609 2.40GHz with Server 2012 64 bit on it. All computers (except on on 32 bit) are running Windows 7 Enterprise edition 64 bit.
Please help.

I made this change to the registry on the server and am waiting to see if I have any more drops.
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\lanmanserver\parameters
Value:
autodisconnect
Data
type : REG_DWORD
Value:
ffff (Hex)
There was a client side change suggested but I am missing that value for the client side change and others in the organization who don't have it are not experiencing this problem.

Questions About Losing Connection

Like other people I've noticed here, my WRTG45 v5 wireless router has recently started losing connection to the net multiple times a day. At first, we thought it was because our modem was old, so we bought a new one, but it didn't fix anything. So here are my questions:
1. My dad seems to think that a configuration or setup CD (that we lost) is required to make the router work with the new modem. Is this true? I don't think so, but I have to ask just so I can get him to move on.
2. I noticed in other posts here that programs like Bittorrent can cause the router to be overworked or whatever. This might explain our problem, as I use Bittorrent a lot (but not everytime the connection has dropped). If this is indeed the problem (or contributing to it), is there anyway to deal with it while still being able to use the program?
For the first couple months, the router was working fine. Even with Bittorrent running a lot, and all the computers (2 wired, 1 wireless, and 1 wired X-Box) engaging in various activities on the net. So this is very puzzling to me.
One more bit of information, I have given every computer a unique, static IP address. However, I noticed recently that when I look at the router configution after typing in its IP address in a web browser, that it is set to DHCP Enabled.
Also, in the advanced TCP/IP settings for this connection, under the WNS tab, the NetBIOS setting is set to the default of using NetBIOS from the DCHP server.
Since I am using static IP addresses, could these DHCP centered settings be causing problems? Although, even if they are, it still doesn't explain why the router was working fine months ago (unless someone changed stuff without my knowing).
Anyway, any help at all would be appreciated.

I assume you meant that you had a WRT54G v5 router.
First of all, the setup CD is not required. All router settings can be made by going to the router's web pages at 192.168.1.1
It is possible that the static LAN IP addresses are causing your problem, if they were not set up correctly. Linksys has a strict set of rules to follow regarding static LAN IP addresses.
With Linksys routers, a fixed (static) LAN IP addresses must be assigned in the device that is using the address. So you need to enter the fixed address in the computer or printer, not in the router.
When using a Linksys router, any fixed LAN IP address must be outside the DHCP server range (typically 192.168.1.100 thru 192.168.1.149), and it cannot end in 0, 1, or 255.
Therefore any fixed LAN IP address would normally need to be in the range of
192.168.1.2      thru 192.168.1.99 or
192.168.1.150 thru 192.168.1.254
assuming you are still using the default DHCP server range.
Also, in the computer, when you set up a static LAN IP address, you would need to set the "Subnet mask" to 255.255.255.0 and the "Default Gateway" to 192.168.1.1
It is also important that no two devices on your network be set to the same static LAN IP address.
Check all of your static LAN IP addresses. If you have violated any of the above rules for static LAN IP addresses, it could be the cause for your problem, and you should fix it before attempting any other router repairs or changes.
You should leave the DHCP server turned on. This way, if you have a visiting friend who you want to connect to your system, it will be easy to do.   Leaving the DHCP server turned on should not cause any problems, even if all your addresses are fixed. In general, you should let the DHCP server assign all addresses, unless there is a specific reason to use a static address. You can mix static and DHCP assigned addresses on the same LAN, as long as you follow the above rules for static addresses.
Linksys routers have had problems when BitTorrent is used. Your router has new firmware posted that should improve compatibility with BitTorrent. It is firmware version 1.02.0   You will need to download and install this firmware (after fixing the static address problem, if any). (Note: When you update your firmware, you should use a computer that is wired to the router. Also, when you do a firmware upgrade, turn off all other computers on your system, and unplug all other wires from the router.) After you have installed the firmware, and powercycled the router, you will need to reset your router to factory defaults, then setup the router again from scratch.
Message Edited by toomanydonuts on 04-12-200712:54 AM

Bittorrent client

Hello guys.
I'm sure you're aware when you have a big list of anime and your friends have one even bigger, you feel the need for a 90 GB animation update. The point is that I need a good bittorrent client for this noble task (you know, you've to fight the boredom with all available resources!), but I'm sort of lost of which should I pick. I've tried transmission (rock solid, but is slow as hell), deluge (nitro-powered client, but is too unstable) and rtorrent (good, but kinda unfriendly). The last thing I've done is to go against my gtk+ and oss spirit and resigned to use the wine+utorrent combo, which gives me the best results (however, is not the idea).
Any suggestions for this poor guy?. Thanks in advance.
p.s. I'm aware that my english sucks, that's why I watch a lot of eng-subbed anime. I improve my jp and my en at the same time

moljac024 wrote:
jt512 wrote:ktorrent is a great application, but it requires the obscenely bloated KDE. You're an Arch linux user, so sack up, grow some balls, and use rtorrent.
Well put.
That's the reason someone made a nice qt torrent client only, namely qbittorrent, which is very similar to transmission and works well.
I forgot to mention that transmission brings also a command line client only (gui and cli are separated in transmission-cli and transmission-gtk), which already includes a simple web interface that does not need LAMP! What is the point of the lightweight rtorrent when its' web frontends need all that other software stack? And command line only for torrents with a lot of files and priorities is way to cumbersome.
I don't know if the transmission-cli web interface already includes a details view now where you can give certain files priority though, since I used it on Ubuntu some time ago when it didn't have such a view, but I saw that it was planned then.
SignorRossi.

BitTorrent Client help needed..

Iam building a BitTorrent Client program...i run each client at different machines and each client will need to interact with the tracker from time to time..How can this be accomplished???Both the client and tracker are java programs.
Iam new to socket programming and i have already read the sun java tutorials on sockets..I need to know if it's possible for the client to call the methods in tracker while being connected through sockets..

KiltedTim
1, I will try and change that to oulook, but as that is by far not my primary email, there are no issues with that email account, all the email I have is either personal (cancun.com.mx) or work related (all other domains, pani.com.mx, etc)
I will try and contact this people, but I am afraid this will be a lost battle... they are really backwards...
now, this gives me an idea, do you think that godaddy can do this contact syncing via the server??
I may try and change the service, as I am not ok with my current provider, but godaddy is way expensive and I am not sure it would good economic idea..
and third.. do you recommend anyone? I now that as this is not a country specific issue, I can change to any provider I want, the only issue would be the support if I am in problems, the phone call would be international long distance and not cheap...
mmmmmm got to think about this..

Internet Connection loss after losing connection between 2 sites

Hello,
I have started working for a company over a year ago and recently we are running into an issue with losing internet after a loss of connection between companies site. Below is a summary of setup.
Company has 2 locations, Site A and Site B..both same domain
Site A has DC and other servers such as ERP, Document Control Software.
Site B has DC, Printer Server, File Server and other essentials servers.
Each site has own independed 20 MB connection.
Site A and B are linked via MPLS and only used for ERP, Document Control software, and DC traffic.
Recently we started to have frequent connection issues with the MPLS and as a result I started to notice none of the users at Site B can access the internet such as google.com, msn.com...etc. As soon as MPLS connection is restored interent works.
The DC at Site B was setup before I started working for company.
I have been trying for the past few days to figure out why Site B is losing connection when MPLS Tunnel is not operational...but so far no luck.
I am very sure that internet traffic is not routed via MPLS because when internet is working the IP lookup such as "whatismyipaddress.com" points to ISP IP address for site B. Also when doing tracert to external website the route is via ISP for
Site B.
I think this issue is related to DNS but cannot tell the cause or how to fix?
Thanks for assistance in advance.

Hi
Having said internet is not routing via MPLS, Even i think to be a DNS issues,
Try to check the below
Ensure all the client DNS is set to AD DNS server
In AD DNS server ensure its not forwarding DNS query to Other site
During outage check any client PC manually changing the DNS IP to 4.2.2.2
- all client DNS are set to AD DNS server
- I checked the properties for the AD DNS and found there are 3 forwarders listed.
The first IP is at Site A which is resolved.
The second IP I am not sure about since it is not even in our subnet (not resolved)
The 3rd IP seemed to be for an old DC that is no longer operational (not resolved).
- During outage if I change client machine DNS to 8.8.8.8 or 4.2.2.2 they can access the internet.
I guess my issue is with the forwarders. Would the right step be remove all 3 forwarded and add 8.8.8.8 and 4.2.2.2?
Thanks.

Been losing connection for magic mouse and wireless keyboard

When I have my MBP running Mavericks in clamshell mode, I lose connections to both magic mouse and apple wireless keyboard in clamshell mode. I've tried all the PRAM SCM, aluminum foil and paper tricks. What I then did was test what happens when I leave the MBP open rather than in clamshell mode and it appears to avoid losing connection, at least that is what I've concluded with Mavericks for now..... anyone else able to replicate this? Having to leave the MBP open is not ideal.

Barry, thanks, still not working. I've tried every thing I can think of or have read, what I'm concluding is that there is either a problem with Mavericks or something has changed on how bluetooth works in Mavericks. Did not have this problem for the last 4 years. I can reproduce the problem when I close the laptop. I had the Bluetooth and wireless card checked out and replaced about 3 weeks ago. Problem has continued.

Windows 8.1 cannot connect to group policy client service

Windows 8.1 laptop under administrator account has this "cannot connect to group policy client service" error.Found the following instructions on internet but I don't see this "Replace owner on subcontainers and objects" box on Permissions/Advanced
popup windows ???
Could anyone help ?
Change the permissions on the relevant keys configuring the Group Policy Client service to allow Full Control to Administrators
Open regedit (Start > type regedit in the search box) and navigate to:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\gpsvc
Right-click the registry key and choose Permissions.
Click Advanced, then click Owner.
Choose Administrators and check the Replace owner on subcontainers and objects box.
Exit the permissions dialog and then open it again.
Click Advanced, then choose Administrators and click
Edit…
Check Replace all child object permissions with inheritable permissions from this object.
Click OK and confirm; exit.
Thank you,

Hello CarLover,
Based on my test, the option Replace owner on subcontainers and objects exists in Windows 7, but doesn’t exist in Windows 8.1.
Please take a look at the screenshot about the option in Windows 7.
Please take a look at the following thread similar to this issue.
http://answers.microsoft.com/en-us/windows/forum/windows_7-performance/why-wont-windows-connect-to-the-group-policy/b73107f8-8447-4599-87a5-65ecc6a63aa0
Best regards,
Fangzhou CHEN
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

External drive conntected to Time Capsule keeps losing connection

I've been having this problem since I bought my TC over one year ago. Other than this everything works fine (aside from the occasional need for a restart).
I have an external 500GB drive attached to my 500GB TC via usb. I use the TC strictly for backups and the other drive to host my media files. When I want to use those files I switch on the drive. Only about half of the time does that work. When it does work everything is fine. I see the drive in the finder as expected.
When it doesn't work, I can see the drive name in the finder. But if I click to go into the folder, I get an error saying that the connection cannot be found.
It shows up in the Airport Utility as normal.
Powering the drive off and on does not help.
Relaunching the finder doesn't help either.
The only way I can connect to the drive again is to either logoff and log back into my mac, or restart the TC.
It seems that my computer is remembering some kind of network disk mounting settings that don't get refreshed when I turn on the drive, but then do get refreshed when I logoff and back in. Does anyone know how I could force that refresh to happen? Has anyone had this problem before?
Any suggestions would be much appreciated
PS all my software and firmware are the latest.
Thanks.

OS X fan
This helped meRe: Time Capsule keeps losing connection in Finder
Dec 17, 2013 4:08 AM (in response to whootang12)
Left click on the Finder icon from the Dock and click "Connect to server...", go to recent server and click on your Airport Time Capsule.
THANK YOU!!!!
This solved it for me!

LaCie external hard drive keeps losing connection to Windows 8.1 computer

Hello all,
My LaCie external hard drive (Rugged version) seems like it keeps losing connection to my brand new Windows 8.1 laptop. The laptop is an HP Pavillion 15-p 133cl TouchSmart Notebook which I just got today. Basically, every few minutes, or if I nudge the external
a bit, the computer will seem like it disconnected and reconnected to the external hard drive in a split second and bring it up in the Windows Explorer. This external hard drive doesn't show any problems connecting to any other computer, but it has occurred
with 2/3 ports on this computer so far. I'm a bit worried, because I definitely DO NOT want the files on this external to get corrupted in any way. What should I do? Thanks a bunch.

may I know your external HDD model, to check which USB version to isolate power and cable connection issue
if this is USB 3.0 try to attached at USB 3.0 at your laptop, your laptop has 2 USB 3.0 and 1 for 2.0, for external HDD with USB 2.0 sometimes need more power / more than 1 connection, sometimes the power will loose
but since the trigger it will disconnect if you nudge the HDD, I suggest back up data to your laptop first, try to change with other data or power cable, try also update your laptop chipset
try to check with other device to isolate port issue
may I know if you are using other PC, did your external HDD also will disconnect if you nudge it?
contact your external HDD manufactured to get some suggestion

Oracle 9i lite connection with a Java Client

Hi,
I would like to connect a Java Client developed using PersonalJava edition for PDA with an Oracle 9i lite version which is also on PDA.
I would like to know is it possible to connect such a client (Java) using some JDBC drivers on PDA.
if yes please do suggest a suitable driver and some input tips as to how to connect a GUI developed in Java directly to Oracle on PDA.
I am not too sure whether some web/application server is required in the whole setup.
because in N-Tier Architecture we have a middle layer of Application /Web servers in between a client screen(usually a Browser) and Database.
but I am not aware weather it is possible to directly connect Java Swing or Client application as I mentioned above developed using Personal edition with a database using only some driver software but no other middle ware component in between.i.e forming a 2 tier client server model.
please do let me know your valuable suggestions at [email protected]
thanks,
Ashish

I connect to the database through the same user that created those tables. Do I still need a public synonym ?

IX-2 losing connection on Transmission bittorrent client

Similar Messages

Maybe you are looking for