Ix2-dl doesn't boot after firmware upgrade

I upgraded to the latest firmware and it won't reboot now. the power light just keeps blinking.

Hello lcgrzy,
I recommend trying the following steps:
--Power off unit, remove power cable and re-seat all disks. Then reconnect the power adapter to attempt to boot up.
--While powered off, swapped the disks to opposite bays. Then see if the unit fully boots after about 5 minutes.
--Try booting the unit one disk at a time to see if either disk will fully boot.
--Try booting the unit one disk at a time to see if the firmware on the unit seems to be ok.
--If the unit does not seem to boot after the above, please call lenovoEMC support.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Similar Messages

T1000 wont boot after firmware upgrade if SCA6000 is connected

Hi guys,
as u may have guessed from the topic, I had a T1000 server with a sun SCA6000 crypto card mounted in the PCI slot. All worked fine until i tryed to upgrade the firmware on the server to the last available release (6.7.8 with patch 139435-06 ) . After the upgrade procedure, the system did not boot anymore. This is the console output with POST after the poweron command:
sc> poweron -c
Enter #. to return to ALOM.
0:0:0>
0:0:0>Sun Fire[TM] T1000 POST 4.30.4.a 2010/01/06 15:23
       /export/delivery/delivery/4.30/4.30.4.a/post4.30.4-micro/Niagara/erie/integrated (root)
0:0:0>Copyright 2010 Sun Microsystems, Inc. All rights reserved
0:0:0>VBSC cmp0 arg is: 0fff0fff.00000211
0:0:0>POST enabling threads: 00000000.0fff0fff
0:0:0>VBSC cntl arg is: 0fff0fff.00000211
0:0:0>VBSC selecting POST MAX Testing.
0:0:0>VBSC setting verbosity level 2
0:0:0>Start Selftest.....
0:0:0>Master CPU Tests Basic....Done
0:0:0>Init MMU.....
0:0:0>L2 Tests....Done
0:0:0>Test Memory....Done
0:0:0>Setup POST Mailbox ....Done
0:0:0>Extended CPU Tests....Done
0:0:0>Scrub Memory....Done
0:0:0>Functional CPU Tests....Done
0:0:0>Extended Memory Tests....Done
0:0:0>IO-Bridge Tests....Done
2010-06-17 17:45:02.383 0:0:0>INFO:
2010-06-17 17:45:02.399 0:0:0>     POST Passed all devices.
2010-06-17 17:45:02.433 0:0:0>POST:     Return to VBSC.
2010-06-17 17:45:02.449 0:0:0>Master set ACK for vbsc runpost command and spin...
SC Alert: Host system has shut down.
SC Alert: Host System has Reset
JUN 17 17:45:22 ERROR: HV Abort: <Unknown?> (217f14) - PowerDown
SC Alert: Host system has shut down.
sc> Guessing an hardware compatibility problem, i tried to remove the SCA6000 board and the system booted again without an hassle.
Unluckily, I need the SCA6000, and I don't have any other server in which to mount it, so I tried to downgrade the firmware to the release I had before the upgrade:
firmware version: 6.6.7
patchid: 136928-05
but the system does not boot anymore with the SCA6000 connected. I even tried an older fw release just to be sure (fw 6.6.1, patch 136928-01), with the same result.
I did not find mention of any incompatibility in T1000 or SCA6000 documentation.
Any help would be REALLY appreciated
Many thanks in advance.

Hi,
This looks similar to the bug 6630313 :: http://sunsolve.sun.com/search/document.do?assetkey=1-1-6630313-1
As described in the bug document, it is due to lower f/w rev. on the SCA6000 and solution is to upgrade the crypto card f/w to 1.1.0 /1.1.0 (bootstrap/operational )or later.
Another workaround would be to install system f/w 6.2.4 or 6.2.8 which works well with crypto card f/w 1.0.4/1.0.7.
Copying relevant part of the document for ref.
=======================
Work Around: The card is recognized by obp and prtdiag with firmware 6.2.4, so at this point customer is using firmware 6.2.4 as workaround.
Customer's crypto card is currently running 1.0.4/1.0.7 bootstrap/operational firmware. Customer can upgrade the card to newer firmware such as 1.1.0/1.1.0 by moving card to a system that boots successfully such as Ontario T2000. After such upgrade, install the card back into T1000 which should boot successfully with sysfw 6.4.0, 6.5.5 or 6.5.11 posted on Sunsolve.
Another workaround is customer can downgrade the T1000 sysfw to 6.2.8 so they can boot with the crypto card. After the T1000 is up and running with sysfw 6.2.8, customer can upgrade the crypto card fw to the latest 1.0 patch on the T1000 itself, then upgrade the T1000 sysfw to the latest
version posted on Sunsolve. This workaround does require customer to have access to an Ontario T2000 system.
Another workaround is customer can downgrade the T1000 sysfw to 6.2.8 so they can boot with the crypto card. After the T1000 is up and running with sysfw 6.2.8, customer can upgrade the crypto card fw to the latest 1.0 patch on the T1000 itself, then upgrade the T1000 sysfw to the latest
version posted on Sunsolve. This workaround does not require customer to have access to an Ontario T2000 system.
========================
HTH
-Mehul

Macbook pro doesn't boot after iOS upgrade

Hi all,
I've upgraded my macbook pro (was requested automatically the upgrade) and after reboot to finish the installation, my macbook doesn't boot up.
Is there any way to boot it up? A kind of boot in safe mode?
I'm trying to power it up but nothing. It doesn't boot at all.
Please, can you help me with this.
Thanks
Álvaro

iOS is for iPhone, iPad not for Mac. So what upgrade are you referring to?

Satellite P10-504 doesn't boot after RAM upgrade

Just got 2x 1GB sticks of DDR 400 soddim's, and no boot.
Now after reading up on what I could find on similar models, seems that these older laptops may not handle that fast of ram?
Would using some DDR 266 be more appropriate?

Hi
If the notebook doesnt boot up then there is a big chance that the RAM is either nto compatible or its faulty.
I think its not compatible.
I found this page:
http://www.orcalogic.co.uk/asp/prodtype.asp?prodtype=7090&ft=m&st=3
According to this page the P10 supports the *200-Pin PC2700 (333Mhz) DDR SODIMM* memory modules!
So your RAMs are not compatible!

MacBook not booting after RAM upgrade

I'm sorry if the case has been already posted.
Yesterday I took my MacBook Alu unibody late 2008 to a RAM upgrade (from 2 to 4gigs) to an offical Mac Reseller. They installed it and showed me that the system loads properly and recognized the new RAM.
I took it home, started working on After Effects and Photoshop and when i wanted to check a video on Quicktime, this program refused to boot.
Then photoshop freeze and after effects did so. I quited all aplications and restarted. On restart after the 'bong' i've got the grey screen white an apple logo and a loading bar underneath, that was it, it never finished loading but shutting down.
After the 2nd try the computer gave me the BAD RAM alarm signal right before the start button was pressed and nothing more. I just managed to start it ONCE on safe mode, but this one also freezed and colapsed.
Today i didn't get the BAD ram alarm but the grey screen and loading bar after shutting down.
I took it back to the reseler, the shop boss who did the upgrade wasn't there , the guys on the morning shift placed the old RAM back resulting the same. So they told me it's a software problem, not hardware and might be caused by a failed firmware update or something i did wrong and since i was showed that the system booted after the upgrade i can't complain or argue that they did somethiing wrong.
So basically the want 80euros to check what's wrong with my computer plus the 120 i already payed them for a RAM that doesn't work and of course the repair cost of the computer.
On monday i'll go to talk to the boss, what do you guys recomend me to tell him? i'm frustrated that the guys there treat me like if i broke my computer for beeing stupid and wanted to get it fixed for free, when it clearly broke after they did something wrong on it!
please advice me!
thanks!
Message was edited by: finn bell

What brand is the RAM? From what you said, it is obvious that the RAM is at fault. I would simply tell them that it is not compatible and return the RAM.
Check the System Profiler to see what it says about the RAM (Apple Logo - About this Mac - More Info) and run this application to test the RAM:
http://www.memtestosx.org/joomla/index.php
If either shows any errors, print out the results and take them with you to the store.

PC-Suite sync fails after Firmware upgrade of E65

After firmware upgrade of E65 PC-Suite stops syncing Calendar & Contacts from outlook. No error messages, just "0 entries has been updated".
- PC-Suite updated to 7.0.9.2
- Outlook 2003
- XP Prof.
Any ideas?
Solved!
Go to Solution.

The funny thing is - the notes are synced???? If I restore some old contacts they'll double up in outlook, so I think the problem is, that the sync app doesn't see the outlook contact & calendar folder.
Does somebody has an idea?

Dreamweaver doesn't work after Yosemite upgrade.

Dreamweaver doesn't work after Yosemite upgrade, it asks to install Java Runtime SE 6, I've tried that, I've also installed latest Java and it still won't boot, keeps asking for for Java Runtime SE 6

You need http://support.apple.com/kb/DL1572
27" i7 iMac (Mid 2011) refurb, OS X Yo (10.10.1), Mavs, ML & SL, G4 450 MP w/10.5 & 9.2.2

Mac mini won't boot after RAM upgrade.

Tried installing new RAM in my Mac Mini, 512MB stock to 2GB of Crucial. Followed the directions to a T, grounded myself the whole time.
Things I've tried so far:
1. Resetting the PRAM, no luck.
2. Holding option at start-up, shows no icon.
3. Holding shift, no luck.
4. Holding X, nothing.
How do I get it to accept a CD if it won't boot?

Welcome to Apple Discussions!
You clearly have a problem, but you don't describe exactly what that is other than that your mini won't boot after the upgrade. What happens when it starts up? Does it attempt to start and hang up on the grey or blue screens, or does it start beeping at you almost immediately after you try and start it up, and also flash the power light?
If the former, then you may have dislodged a connector while working inside the system, in which case opening it up and checking that everything is firmly connected would be the first thing to do. If the latter, then the beeping/light flashing is the system telling you it has failed the power-on self test and the pattern of beeps/lights indicates why. In your case likely the system can't find workable memory. In that instance, opening the system and ensuring that the RAM is firmly and fully seated would be a good step, and if the mini continues to fail, then replacing the new RAM with the original to test that the system will then start.
It is not likely that anything had damaged your MacOS install in the process of upgrading, thus normally no reason to need to boot to CD as a result of a RAM issue.

MEGA 865 Computer doesn't boot after flashed.

my problem is .. :
Update My Mother Board Bios and dawnload a file from this site
a file is (AWFL833D.EXE W6797IMS.130 ) for update my mother board Bios
when update completed Restart a Computer ... and here a problem
my Computer doesn't boot after flashed.
i read a (How to flash the BIOS.doc) file and executing a instructions and i am fail.
when i read a (How to flash the BIOS.doc) file i found a Write:
If your system doesn't boot after you flashed, please refer to the BIOS recovery method as described.
i changed a Mother Board clear CMOS jumpers for clearing ,
and not success and the problem is until stay.
i want a solution please.
thanks.

Does your computer do or show any error mesages on the screen when rebooted. You did do this in DOS didn't you?

LDom doesn't boot after SAN controllers replaced

I have an LDom that was installed on a SAN volume. Both of the SAN controllers needed to be replaced, and now we get the the following when trying to boot this LDom:
Boot device: /virtual-devices@100/channel-devices@200/disk@0 File and args:
Evaluating:
The file just loaded does not appear to be executable.
I can mount the volume directly on the host (with the LDom unbound) and all the slices appear fine. I also ran fsck, and it reports no problems.
I can boot the LDom of the net and run an upgrade, but it still does not boot after the upgrade.
This appears similar to:
http://forum.java.sun.com/thread.jspa?threadID=5166845&tstart=90
But, that is for an LDom inside a file.

a=s0, b=s1 etc
/virtual-devices@100/channel-devices@200/disk@0:f
?

Crippled 192.168.1.1 page after firmware upgrade

hi,
i recently upgraded the firmware of my WRT160N V2 to 2.0.03.
but since then when i login i get a crippled page on 192.168.1.1 with not even a menu. so i cant even downgrade. is there something i can do?

It is good to know that the issue is resolved
After firmware upgrade it is always recommended to reset and reconfigure the router and I think that is why you were unable to see the menu on the setup page of your router.

T410i SSD user and master password problem after firmware upgrade

Hello.
I have problem with my Corsair Force 3 120GB SSD. After firmware upgrade of SSD my master and user HDD passwords are no longer valid. I'm stuck on BIOS screen and cannot unlock my SSD. After firmware upgrade procedure i got BSOD. Same happened during firmware upgrade on my previous SSD (INTEL X25-M 80GB) but after restart everything was OK. Please help!
Previous firmware version: 1.3
Current firmware version: 1.3.3
SSD connected to another computer shows RAW partition data, but firmware version is 1.3.3 - seems like update was successful.

My X301 Intel x18 got bricked also after a BIOS update then secure erase (was going to sell it). I plugged it to a USB kit and onto a desktop and it was recognised and able to format. But plugging it back to the lenovo it is still a brick. My lucky star there was warranty it was replaced by lenovo.
You may want to try it and extract the data, if it works. And hopefully you can still format it and made it work pluggin back to the lenovo.

SG300-28 switch in boot loop after firmware upgrade

After performing a firmware upgrade on an SG300-20 switch from ver 1.1.0.73 to 1.2.5.70 the switch now boots up with the following error and resets:
30-Aug-2011 10:47:33 %L1Mngr-F-PARAMTOOLONG: csco-sb parameter %s is too long.
The attached file contains a full output of the console boot process.
I have tried loading different versions from the console, but all produce the same error.
Has any one any idea how to resolve this issue?
Thanks
Des

Hello Tom, Thanks for your reply,
I had done the process before with the 3 firmwares offered in the cisco website. I did it again, and i get a boot loop again, with following error:
%L1Mngr-F-PARAMTOOLONG: csco-sb parameter serialNo is too long.
Any ideas?
Thank you,
Nico
Console
     Startup Menu
[1] Download Software
[2] Erase Flash File
[3] Password Recovery Procedure
[4] Set Terminal Baud-Rate
[5] Stack menu
[6] Back
Enter your choice or press 'ESC' to exit:
Downloading code using XMODEM.
-- Download complete --
Calculating file's checksum...OK
Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
Writing to flash 0x6aa500 records...
Setting checksum: 0x350925f6 , Address: 0x0
OK.
Flash programming success.
Perform WARM BOOT ...
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.0.4 Built 08-Apr-2010 16:37:57
Networking device with Marvell ARM CPU core. 128 MByte SDRAM.
I-Cache 16 KB. D-Cache 16 KB. L2 Cache 256 KB. Cache Enabled.
MAC Address   : 58:35:d9:96:7f:5d.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
Decompressing SW from image-1
100%
OK
Running from RAM...
Board ID is 22
Device ID 0xdf5111ab
*** Running SW Ver. 1.2.7.76 Date 19-Jul-2012 Time 17:54:43 ***
HW version is V
Base Mac address is: 58:35:d9:96:7f:5d
Dram size is : 128M bytes
Dram first block size is : 101376K bytes
Dram first PTR is : 0x1900000
Dram second block size is : 4096K bytes
Dram second PTR is : 0x7C00000
Flash size is: 16M
19-Jul-2012 17:54:46 %CDB-I-LOADCONFIG: Loading running configuration.
19-Jul-2012 17:54:47 %CDB-I-LOADCONFIG: Loading startup configuration.
Device configuration:
Slot 1 - SF302-08MP
Device 0: GT_98DX1005 (AlleyCat)
-- Unit Standalone                --
Tapi Version: v1.9.5
Core Version: v1.9.5
19-Jul-2012 17:55:02 %L1Mngr-F-PARAMTOOLONG: csco-sb parameter serialNo is too l
ong.
***** FATAL ERROR *****
Reporting Task: ROOT.
Software Version: 1.2.7.76 (date 19-Jul-2012 time 17:54:43)
***** DEBUG *****
DEBUG LOG IS EMPTY
0x16a614
0x167054
0x6bdc18
0x490518
0x4959e4
0x495bac
0x815674
0x816b10
0x817e64
0x1d51e8
0x1cb010
0x121d3c
***************** SYSTEM RESET *****************

3750x doesn't boot after upgrade to version15

Due to a problem with POE+ i have tried to upgrade the IOS to Version15.0.2SE2, from 12.2.58. unfortunatly the Switch doesn't boot up anymore. It starts to decompress and install the IOS 2 Times, after the Second try it displays "unable to boot" and the switch goes in Bootloader-mode.
When i look at the version i See that bootloader is still the old version 12.2.58.
It seems that the bootloader doesn't geht upgraded and that's why the Switch can't Boot the new Image.
Is there anything i can do to Upgrade the bootloader seperatly?
It's a 3750X48PF-S
Many thanks
Andy

This is a stack of 2 switches, both have the same problem and they are still running old image (as V15 doesn't work)
cs156005#sh license
Index 1 Feature: ipservices
        Period left: 8 weeks 4 days
        License Type: Evaluation
        License State: Active, Not in Use, EULA not accepted
        License Priority: None
        License Count: Non-Counted
Index 2 Feature: ipbase
        Period left: Life time
        License Type: Permanent
        License State: Active, In Use
        License Priority: Medium
        License Count: Non-Counted
Index 3 Feature: lanbase
        Period left: 0 minute 0 second
cs156005#sh inventory
NAME: "1", DESCR: "WS-C3750X-48P"
PID: WS-C3750X-48PF-S , VID: V02 , SN: FDO1527P0J8
NAME: "Switch 1 - Power Supply 0", DESCR: "FRU Power Supply"
PID: C3KX-PWR-1100WAC , VID: V02L , SN: LIT15060D4H
NAME: "Switch 1 - FRULink Slot 1 - FRULink Module", DESCR: "FRULink 10G ST Module"
PID: C3KX-NM-10G       , VID: V01 , SN: FDO14350PDY
NAME: "GigabitEthernet1/1/3", DESCR: "1000BaseLX SFP"
PID: Unspecified       , VID:      , SN: PR04004346
NAME: "2", DESCR: "WS-C3750X-48P"
PID: WS-C3750X-48PF-S , VID: V04 , SN: FDO1649P24J
NAME: "Switch 2 - Power Supply 0", DESCR: "FRU Power Supply"
PID: C3KX-PWR-1100WAC , VID: V02L , SN: LIT16371ZBN
cs156005#sh version
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 05-May-11 01:56 by prod_rel_team
ROM: Bootstrap program is C3750E boot loader
BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M) Version 12.2(53r)SE2, RELEASE SOFTWARE (fc1)
cs156005 uptime is 1 hour, 14 minutes
System returned to ROM by power-on
System restarted at 10:11:49 cet Tue Jul 9 2013
System image file is "flash:/c3750e-universalk9-mz.122-58.SE1/c3750e-universalk9-mz.122-58.SE1.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Level: ipbase
License Type: Permanent
Next reload license Level: ipbase
cisco WS-C3750X-48P (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1527P0J8
Last reset from power-on
2 Virtual Ethernet interfaces
1 FastEthernet interface
104 Gigabit Ethernet interfaces
4 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : A4:93:4C:95:EC:00
Motherboard assembly number     : 73-12553-05
Motherboard serial number       : FDO162001GA
Model revision number           : A0
Motherboard revision number     : D0
Model number                    : WS-C3750X-48PF-S
Daughterboard assembly number   : 800-32727-01
Daughterboard serial number     : FDO16200KPU
System serial number            : FDO1527P0J8
Top Assembly Part Number        : 800-31324-02
Top Assembly Revision Number    : E0
Version ID                      : V02
CLEI Code Number                : COMJZ00ARB
Hardware Board Revision Number : 0x03
Switch Ports Model              SW Version            SW Image
*    1 54    WS-C3750X-48P      12.2(58)SE1           C3750E-UNIVERSALK9-M
     2 54    WS-C3750X-48P      12.2(58)SE1           C3750E-UNIVERSALK9-M
Switch 02
Switch Uptime                   : 1 hour, 14 minutes
Base ethernet MAC Address       : 44:03:A7:58:AC:80
Motherboard assembly number     : 73-12553-08
Motherboard serial number       : FDO164831LB
Model revision number           : K0
Motherboard revision number     : A0
Model number                    : WS-C3750X-48PF-S
Daughterboard assembly number   : 800-32727-03
Daughterboard serial number     : FDO16491JNK
System serial number            : FDO1649P24J
Top assembly part number        : 800-31324-07
Top assembly revision number    : B0
Version ID                      : V04
CLEI Code Number                : COMJZ00ARD
License Level                   : ipbase
License Type                    : Permanent
Next reboot licensing Level     : ipbase
Configuration register is 0xF
cs156005#

Satellite M200 doesn't boot after RAM 4GB upgrade

Hi,
I recently upgraded my RAM just to speed things up a little as RAM is soo cheap these days.
I have a M200 T2130 Vista came with 1GB (2*512) sticks.
The new sticks are 2 *2GB Dane-elec DDR2 pc2-5300, when I put the two in and rebooted the hard drive light came on briefly and then it just stayed idol, no POST, Bios options.
I tried using a single 512 stick with both new sticks and they both work in a 2.5GB setup just not together also this only works when the 512 stick is in the more internal slot and not the other way around.
So if anyone has had a similar prob or can give me some advice that would be great, I'm not to sure if the motherboard can support 4GB?
Thanks, Dave.

Hi
There are two possibilities why your M200 doesnt boot after the RAM upgrade.
Firstly the installed RAM could be not compatible or could be faulty or the notebook doesnt support the 4GB RAM.
I dont know what M200 do you have exactly but you could check the installed chipset and could check on the Intel page if this chipset would support the 4GB RAM.
Greets

Ix2-dl doesn't boot after firmware upgrade

Similar Messages

Maybe you are looking for