J4550 error message "Alignmnet page not detected" -alignment page prints ok

j4550 Printer will not align. Alignment page prints correctly (per HP website), but scanning page gives an error message "Alignment page not found". Printer copies fine. Default alignment results in blurred printing.

Hello , Welcome to the thread!  I understand that your HP Officejet Pro 8500 All-in-One A909a Printer is experiencing Printhead and Alignment failures. Because you have already replaced both the Cyan and Magenta Printhead (twice) and Black and Yellow Printhead in the past and the issues continue to occur over time I believe that the Printhead sensor or print system within the actual printer is going. Should this occur then print system issues, such as Alignment, Printhead, cartridge, quality, etc issues will occur and will usually become worse over time. Therefore, rather then replacing the Printheads it may be time to replace the actual printer. With that being said, there are a few troubleshooting steps that I would like you to complete to resolve this issue.   To start, please click here . Once the support document opens please review all of the listed Solutions and sub-steps to ensure that all steps have been completed. Should the issue persist, then a Firmware Update may be needed on your printer. However, I do need to know what Operating System you're using on your computer in order to provide you with the correct Firmware Update. The Firmware is the internal programming within your printer. It controls what your printer does and how your printer does it. If there is a corruption within the internal programming in your machine, your HP Officejet may not respond correctly.   Please respond to this post with the result of your Alignment Failed troubleshooting. Should the issue persist, be sure to include your Operating System in your response so I can provide you with the additional Firmware Update. I look forward to hearing from you!

Similar Messages

  • Ipad, Error message "Safari could not open the page"

    Hi... I am getting the error message "Safari could not open the page because the server stopped responding" 
    I have read the previous replies to this error message and have made sure the Ipad is connected to internet (skype works fine.)
    I have also done a hard reset on my Cisco router.
    I have Reset Ipad to factory settings twice.
    I have Reset network settings five times
    I have Powered off and on five times,
    turned wifi off and on countless times.
    Any idea other ideas? Ipad was bought in US 3 weeks ago.  Worked fine at hotel in mexico.  I am now in Bolivia.  Different countries screwing it up? Could my router be too old? My Mac and iphone work fine on it though, although they are also old and since my macbook refuses to update it runs on OSX 10.5.8
    Thanks, your help is immensely appreciated.

    Can you connect to the internet using other WiFi networks? Have you even tried outside of your own home WiFi network? Have you tried anything I here yet?
    iOS: Troubleshooting Wi-Fi networks and connections
    Occasionally I get this message in Safari but I also can't get online with any browser when I get the message. What I always do - and it always works for me - is to close all apps on my iPad and reset the device. I don't know if closing apps has any real effect or not. Most likely is it the system reset that brings it back to normal behavior.
    Due to the fact that you have restored to factory settings twice already, I can't believe that resetting the iPad would do any good at all. But you are getting nowhere anyway, so try it if you like.
    In order to close all of your apps, drag the app up from the multitasking display. Double tap the home button and you will see apps lined up going left to right across the screen. Swipe to get to the app that you want to close and then swipe "up" on the app preview thumbnail to close it.
    Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

  • I am trying to print a fillable form.  It will not print and I get two error messages "document could not be printed" and "there were no pages selected to print."  Th latter is not true.  Won't print all, the page I am on, nor any series of pages inserted

    I am trying to print a fillable form - - an application for a Chinese visa.  It will not print and I get two error messages:  "document could not be printed" and   "there were no pages selected to print."  The latter is not true.  Won't print at all, the page I am on, nor any series of pages inserted.
    Am using a MAC desktop and a Cannon PIXMA MX922 printer.
    I need to print this form now that it is filled out?  What can I do? 

    Hello PW, I am having this problem and all suggestions haven't worked yet. Where is the Preferences|Documents you are referring to? I am on a PC and using Windows.
    EDIT: I found it and did, but still not working.

  • I recently purchased a MacBook Air and was told by Apple that Keynote and Pages were compatible with MS Applications.. I have since tried to open a Powerpoint Presentation but it comes up with an error message and is not right. Help!

    I recently purchased a MacBook Air and was told by Apple that Keynote and Pages were compatible with MS Applications.. I have since tried to open a Powerpoint Presentation but it comes up with an error message and is not right. Help!

    If there are fonts, transitions, builds, video or audio in the PowerPoint file that are not compatible with Keynote, it will either prevent the presentation opening or Keynote will substitute the settings causing playback changes.
    I use Open Office to play and open any PowerPoint files sent to me, they play exactly as in PowerPoint.
    Open Office is free, you can download it here:
    Open Office for Mac

  • I get error message iTunes could not sync calendars to iPhone because an error occurred while merging data

    I get error message iTunes could not sync calendars to iPhone because an error occurred while merging data on my wifes phone how do you correct problem without losing calendars info on phone.

    One thing that might help.
    1. open itunes preferences from the edit menu and click on the devices tab.
    2. check the box to disable syncing for iphones connected to itunes and click ok.
    3. Then click the button to reset sync history.
    4. Now click ok to close the preferences window.
    5. connect the iphone to itunes and go to the info tab.
    6. scroll to the bottom of the info page and check the box to replace the ical data on the iphone.
    7. then click apply on the bottom right of itunes.
    This will overwrite any events on the iphone, including any events that has become corrupted.
    Hope this helps

  • I am using Adobe Acrobat 9 Standard version in Windows 8.1 and when I try to create a .pdf file, I receive the following error message "Acrobat could not open "file name.log" because it is either not a supported file type or because the file has been dama

    I am using Adobe Acrobat 9 Standard version in Windows 8.1 and when I try to create a .pdf file, I receive the following error message "Acrobat could not open "file name.log" because it is either not a supported file type or because the file has been damaged.  To create a PDF document, go to the source application then print the document to .pdf"  I am going to the source application and printing the document to .pdf yet it's saving the file as a .log file.  After reinstalling the software, I initially didn't encounter this problem but on my second and third attempts to convert files to .pdf format, this error message reappeared.  How do I resolve this problem?

    I have a similar problem which i did not have before...and it exists only in some powerpoint files which i want to print as a pdf file...and i get the same message as above.
    the log says the bellow details...what's the problem and how can i resolve it? thanks.
    %%[ ProductName: Distiller ]%%
    %%[Page: 1]%%
    %%[Page: 2]%%
    Cambria not found, using Courier.
    %%[ Error: invalidfont; OffendingCommand: show ]%%
    Stack:
      %%[ Flushing: rest of job (to end-of-file) will be ignored ]%%

  • How to get rid of the error message we could not complete your iTunes store request?

    How to get rid of the error message we could not complete your iTunes store request?
    having this problem when trying to authorise an newly downloaded app in iTunes

    Based on the numerous posts regarding iTunes and the App Store, there appears to be an issue at Apple's end. Although Apple has not provided any indication on the cloud status page.
    Do not change your settings.
    Edit

  • Hp recovery on laptop gives error message "destination drive not connected"

    I'm trying to carry out factory reset on my 2012 G6 laptop product code B2Y48EA*ABU  serial no. [Personal Information Removed] to factory settings using set of 5 recovery discs
    I followed the procedure  shown here  (although the screen messages are slightly different)
    http://support.hp.com/gb-en/document/c01867418
    I started the laptop with disc 1 in the dvd drive and the hp program was displayed. I selected "factory reset" and followed promts
    When the 4 th disc is in dvd drive and the process is about53% compltete it stops with the error message 
    "destination drive not connected"
    and fails
    Earlier the recovery manager reported that the partion on the hard drive had been re-forrmatted so the drive was connected then!
    All help and suggestions appreciated

    Hi there @Teka,
    I understand that you are having trouble with a System Recovery to a factory image using recovery disks. I am happy to help you with this.
    Are those five disks a set that you created using the recovery manager, or is it a set you ordered from HP?
    Is there any sign of damage, scratches or smudges on the disk it fails on?
    Have you tried cleaning the DVD drive?
    Also take a look through these pages, in particular the troubleshooting page, and see if anything there is of use.
    Performing an HP System Recovery (Windows 7)
    Troubleshooting HP System Recovery Problems (Windows 7)
    Let me know how it goes for you.
    Malygris1
    I work on behalf of HP
    Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
    Click Kudos Thumbs Up on the right to say “Thanks” for helping!

  • I have created PDF from hardcopy by using my scanner. After I run OCR option for my PDF by using Acrobat Pro 9. But "Text-to-speech" functionality of the PDF says that an error message comes up that says the page is empty when I turns on the read out loud

    I have created PDF from hardcopy by using my scanner. After I run OCR option for my PDF by using Acrobat Pro 9. But "Text-to-speech" functionality of the PDF says that an error message comes up that says the page is empty when I turns on the read out loud option in Acrobat. Kindly help me to sortout this problems?

    So I tried generating the same PDFs on two other computers that have Acrobat 9 Pro.  Results were reproduced.  The verdict is:
    - complex PDF files (that is, containing cross-references, tables of contents, and bookmarks) generated by Acrobat 9.x Pro are roughly 2-5x larger than the identical file generated with Acrobat 8.x Pro.
    - different PDF conversion settings make a negligable difference (less than 10% rather than 70-80%).
    - using the "Reduce File Size" or "Optimize PDF" option cuts the file size roughly in half, almost always resulting in a "image downsampling mask" warning message, which requires acknowledgement (that is a problem for batch processing or automation).
    - adding an Acrobat watermark to the file cuts the file size roughly in half.
    - just using Save As to another filename has no effect on file size.
    - generating the PDF in Acrobat 9 with links but no PDF bookmarks still results in the inflated file size.
    - generating the PDF in Acrobat 9 without any links or bookmarks results in approximately the same file size as the Acrobat 8 PDF with full links and bookmarks.
    It appears that Acrobat 9's manner of adding links is what's bloating  the files, and in my case it's probably not related to images or image resolution/print quality.  It's a shame, because Acrobat 9 seems to have made some  improvements to the Review Tracker interface, and a few other bells and  whistles which I haven't really gotten around to exporing yet.  But  unless I find a way to keep my links and the PDF file sizes comparable to what I was  getting with Acrobat 8 Pro, it looks like I'm going to stay with Acrobat 8.

  • Error message when moving to a different page

    Post Author: EvDev
    CA Forum: .NET
    I have an ASP.NET 2.0 and Crystal Reports 11.5 project that works fine
    when it's being debugged and when it's on our test server, but when we move it
    to our production server the user will receive an error message when moving to a
    different page of the report.  It's an
    "Object reference not set to an instance of an object".  It seems very
    odd for me for something to work on the test server but not on production.   Has
    anyone seen this before?  Thanks

    Hi there,
    This does seem like a very valid process to be sure
    I'm guessing that the fix is shown in "Solution 1" in this doc;
    http://www.cisco.com/en/US/partner/products/sw/voicesw/ps556/products_tech_note09186a0080b04158.shtml
    Cheers!
    Rob

  • Keep getting error message that iphoto has detected inconsistencies and needs to rebuild

    while adding photos to library keep getting error message that iphoto has detected inconsistencies and needs to rebuild the library..how do I fix?

    By rebuilding your library.
    Back up your iPhoto library before you do that.
    If iPhoto is open, quit it.
    Hold down the Option and Command keys while you open iPhoto (click the iPhoto icon in the Dock).
    The Photo Library First Aid window opens.
    Click "Rebuild database" and click the "rebuild" button.
    If this does not solve the problem, see "option 2" in Terence Devlin's post here:
    Re: i keep getting the message iPhoto has detected inconsistencies in your library but after repairing it it just quits
    Regards
    Léonie

  • Cant open itunes. Get error message CMBlockBufferCopyDataBytes could not be located in the dynamic link library CoreMedia.dll. Anyone know how to fix that?

    Cant open itunes. Get error message CMBlockBufferCopyDataBytes could not be located in the dynamic link library CoreMedia.dll. Anyone know how to fix that?

    For general advice see Troubleshooting issues with iTunes for Windows updates.
    The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down the page in case one of them applies.
    Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
    The error hints at a similar pattern to those discussed in the first and third boxes of the user tip, suggesting that you've got an outdated .dll file that needs replacing. You should find CoreMedia.dll in the one of the following folders:
         C:\Program Files\Common Files\Apple\Mobile Device Support
         C:\Program Files (x86)\Common Files\Apple\Mobile Device Support
    Delete it and then repair Apple Mobile Device Support from the Programs and Features control panel. If that doesn't work go for the full tear down and rebuild.
    tt2

  • Itunes wont open at all, error message : quicktime was not found .... please reinstall ... i did that but no luck this only seems to have happened since the 10.4 update, im on windows 7 ..

    itunes wont open at all, error message : quicktime was not found .... please reinstall ... i did that but no luck this only seems to have happened since the 10.4 update, im on windows 7 ..

    Can you start QuickTime on your computer?
    You'll probably have to search for the Windows Installer Cleanup Utility and use it to remove QuickTime Player and iTunes. Then download and install the iTunes again.

  • Error Message: Number is not in external Interval (Testing Schedule)

    Hii ,
    Iam working on Stability study process. I have maintained stabity test with materiial (QS) & performed my test upto Initial test of Inspection lot. But when i click create Testing Scheudle in the Notification (QM02) , system asks for testing schedule data for
    Maintenane strategy, scheduling period.
    On clciking create testing schedule , system throws error message "Number is not in external interval". I have maintained all the prerequite setting on number range in following spro path stability study>testing schedule for stability study> Category--> no range.
    For Group ST   600000000- 6999999999 for Intenal & 70000000-7999999999 for external. But still iam facing with error message ""Number is not in external interval".  It throws message no "IP324" . Even I had cross checked with maintenance setting, but error message remains . How to resolve this issue?
    with regards,
    K.Lokesh.
    Edited by: Lokesh K on Mar 11, 2010 1:13 PM
    Edited by: Lokesh K on Mar 12, 2010 5:55 AM

    Hi Lokesh,
    did you actually enter a number ( i.e. 70000001)?
    Usually Stability studies are created using the external number range so that ringing names can be used for the studies:
    Example:
    Material: 000000000000000001  acetylsalicylic acid
    Stability study: ASA1
    I hope that this information proves usefull.
    Regards
    Isabelle

  • I get error message''one file not found'' when tring to sync Ipod Nano 6th gen to I tunes. Help

    I get error message''one file not found'' when tring to sync Ipod nano 6th gen to Itunes. Help

    See:
    iTunes cannot sync... apps not determined installed on...: Apple Support Communities
    installed apps could not be determined...: Apple Support Communities

Maybe you are looking for