J6450 cannot be detected on network

Help this low-techie, please! My 6450 prints through the USB, but cannot be detected wirelessly. When I try to reset the network (or install via the CD) the USB connection does not recognize that the printer is connected (though it will print documents via that same USB). I ran the Wireless Network Test Report, and in the Diagnostics Summary, it shows:
Wireless On PASS
Wireless Working FAIL
Therefore, the remaining tests are not run.
Because I cannot get the PC and printer to recognize each other for the purpose of setup, I don't know what to try next. (BTW, the current and correct drivers are installed on the laptop)
Thanks.

I think your printer's wireless radio has died. Let's reset the printer to try to revive it.
Turn the printer off
Hold the # and 6 keys while and a bit after turning the printer on
Run the self-test again (Setup > Network > Wireless Network Test or some such words)
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Similar Messages

Hello everyone, I just updated my 3GS from iOS 5.0.0 to 5.0.1 Since the update, Itunes says that no SIM card is detected, and the iPhone says that it cannot be activated. It also obviously does not detect any network. I tried restarting the phone se

Hello everyone,
I just updated my 3GS from iOS 5.0.0 to 5.0.1
Since the update, Itunes says that no SIM card is detected, and the iPhone says that it cannot be activated. It also obviously does not detect any network.
I tried restarting the phone several times, removing the SIM card several times, but it did not change anything, the SIM is still not detected.

You do not need to keep posting the same thing over and over again.
Look to the right side of this page at "more Like this" or do a forum search.

I am getting weary of my iPhone 4s. the battery life is non-existent, second, i had problems with calls, the caller couldn't hear me and now it cannot detect internet networks. Be they wi-fi or cellular. what could be the problem.

I am getting weary of my iPhone 4s. The battery life is non-existent, secondly, I had problems with calls, the caller couldn't hear me and now it cannot detect internet networks. Be they Wi-Fi or cellular. what could be the problem?

Mullaly75 wrote:
I assume u guys don't understand what open source software is
Yes, I think most of us do understand what open source software is. It sounds as if you don't. Here's some information:
Open-source software (OSS) is computer software that is available in source code form: the source code and certain other rights normally reserved forcopyright holders are provided under an open-source license that permits users to study, change, improve and at times also to distribute the software.
Open source software is very often developed in a public, collaborative manner. Open-source software is the most prominent example of open-sourcedevelopment and often compared to (technically defined) user-generated content or (legally defined) open content movements.
from http://en.wikipedia.org/wiki/Open_source_software
Yes, Tom Wu of Stanford wrote a paper on something called Secure Remote Access Protocol. It's a form of Asymetric Key Exchange and has nothing to do with hacking anything. It's actually intended to protect data.

I purchased recently an ipad 2 wi-fi 3G and the device cannot detect any network, I turned the wi-fi on and reset the network, but still cannot detect the network

dear friend
I recently purchased an ipad 2 wi-fi 3G. the device cannot detect any network, I do not know why. I tried to reset the network, but without any vail. could you please tell me what the setps so I can solve the problem. Another problem, I connected the ipad device with cable to my pc, but the pc is not recognizing the device. The pc only shows the pictures on the ipad.

lets start easy so the we can understand where you are in the process. Have you set the ipad up using itunes? if not, you need to do that first. make sure your computer has the current i tunes version loaded, then plug the pad into the computer. What kind of computer you using, mac or pc?
If you haven't set it up, then it does not know to look for any networks.

IMac no longer detecting any networks...

Hi again all...
My 24 inch white iMac recently went in for repair after having graphics issues (no other issue ever, everything perfect). It came back, switched it on, runs fast again and has no graphics issues.
However, Airport now does not seem to be detecting ANY network at all. Normally it would pick up my home network (router in the next room), as well as 1-2 other networks which are likely from other houses nearby. This has always been the same for the life of the computer. My MacBook has absolutely no issues detecting my home network as well as other networks, as per usual.
I have tried resetting the SMC, PRAM, removing and re-adding Airport, running Network Diagnostics, etc but it just cannot find anything at all. I even tried messing with my router a bit by changing the security a few times, the MacBook detected it fine again, but nothing on the iMac. Same thing after trying another router too. Also, the Airport card seems to be detected fine in System Profiler.
I cannot seem to figure out what's causing this and how to resolve it. Please can anyone advise me on what else I could try and what the problem could be?
Thanks, hope you guys can help!

HI,
Try changing the Airport Channel.
Open AirPort Utility (Applications/Utilities)
Select the device you’re setting up on the left and then click Manual Setup. Enter the base station password if necessary.
Click AirPort in the toolbar, and then click Wireless.
Choose a new channel from the Channel pop-up menu.
If that doesn't help, go to /Library/Preferences. Move all the files in the System Configuration folder to the Trash, restart the iMac.
If nothing above has helped, try the Airport Troubleshooting Guide here.
Carolyn

Airport express cannot be detected in one of my Macs

Both our macbooks are connected to our network but my imac cannot detect the airport express. The imac can detect the network I am trying to join but I cannot connect to it. I open airport utility but it cannot find the airport express. What should I do? Thanks for your help

socdoc wrote:
The imac can detect the network I am trying to join but I cannot connect to it.
You might try resetting your connection settings using the steps listed in this message:
http://discussions.apple.com/thread.jspa?messageID=10695921&start=1
They're not guaranteed to solve the problem, but they'll only take a minute or so to try.

Windows did not detect any networking hardware, Windows 7, New Hard Drive

Message "Windows did not detect any networking hardware"
Satellite P505 S8980 Windows 7 Home Premium.
I replaced the Toshiba 500 GB HD with 500 GB Seagate.
Device Manager icon for any device with yellow exclamation mark,
Click on "Update Driver". Lan eNet details as follows:
Antheo - R8132 PCI-E Fast Ethernet Controller (NDIS 6.20)
Browse to the folder where the setup program has the driver...
Message: "The best driver software is already installed."
(But the yellow exclamation mark still harasses me.)
--- Go to "Setup new connection" ---
"Choose a connection option"
Click on "Connect to the Internet"
Response: "Windows did not detect networking hardware"
As near as I can tell, that translates from error 0x8E5E0247
I have this same error on other yellow exclamation marks respective of what kind of device it is.
=> To test my sanity, I put the old hard drive (same size) back in and except for the impact of slowness due to error retries, everything works okay.
Note:
Same issue (hardware not detected) for Video adapter and Audio.
I bought new USB Wireless adapter to test, and the driver installed but not activated because "not digitally signed", and that same issue fits all the above hardware. I down loaded them from Toshiba, and they are confirmed installed, but not accepted with digitally signed. I have uninstalled and reinstalled with same results.
Solved!
Go to Solution.

I'm discovering I am not as well as I thought... running on the AF hard drive which was built with a copy drive from old format drive which was the product of system recovery disc set.
Review for context: Advanced Function HDD
Scenario that exposes harm caused by cloning data from 4K blocks drive to 512 bytes blocked drive (AF)
Toshiba supplied Windows-7 System Restore Discs: to factory state
Then I built the Windows-7 Repair Disc... used later.
Hard drive was replaced when it caused SMART warning at every system boot.
Acronis was only utility that quickly detected problem (3 sectors had permanent read errors.) Active@Disk Image and Power Quest Drive Image (Ghost) did not detect the issue.
I tried Seagate 500 GB and Western digital 500 GB HDD drives as copy target.
That new drive would not boot: "Required source not found"
Booted My newly created Windows-7 repair disc, and used to to fix startup.
See images.
That worked and then the ST9500423AS disc booted.
Now... next day I discovered Window Update is not working.
I get message:
Windows Update cannot currently check for updates, because the service is not running. You need to restart your computer.
I ran Microsoft Fixit for updates. It says it fixed two items.
I still have the problem.
The service shows "started"
Control Panel/ ACTION Center/ Maintenance/ Check for Updates
"No action needed"
"Windows Update does not require any action"
I checked Update History...
... It is empty, else window is vacant... blank.
Soooo..... for a sanity check, I swap out hard drive; go back to the old format (which is the one I copied).
It works! 7 updates to install, including SP1... but I did NOT install them.
Switch back to the AF drive... Update doesn't work. I am broke again.
Is this another strange problem caused by the Advance Format issue?
What to do?
By the way... I did install an Intel storage Matrix driver update, but I do not have RAID chip, so that driver is not for me... unless I missed out on something.
Carl

Server cannot be detected

When i try to upgrade my ipad2 i keep getting a messege that says "the ipad software update server cannot be detected. Make sure your network settings are correct and your network vonnection is active." i dont know what to do, please help. My internet is working fine, by the way.

Jimwhite138-
It is possible Apple was doing maintenance on the server when you tried. Give them a few minutes and try again.
When you say your internet is working fine, do mean on the iPad or on your computer? If on the computer, you may be having a problem on the iPad. Try unplugging your WiFi router for a few seconds. Then reset the iPad's network. Go to Settings-General-Reset-Reset Network Settings. You will need to reconnect the iPad's WiFi.
Fred

Before my carrier was showing airtel now after using ultrasnOw to unlock it is now unable to detect any network list

before my carrier was showing airtel now after using ultrasnOw to unlock it is now unable to detect any network list now i cant use any connection plz

jailbroken phones cannot be supported here.

Airport client ceased to detect available networks

Hello all,
I am switching this topic to this forum to see if you all can help. I have searched high and low in the support and community archives and cannot find anything. I am suspecting a Mini configuration issue, but I reached the extent of my knowledge a long time ago…
Here is what I have:
Environment
Home network with Airport Extreme as base – up to date firmware
Computers in the network: Mac Book, Mac Mini and an HP Laptop
Both Mac Book and Mac Mini are running Mac OS X 1.5.8
Firmwares on both up to date (wireless firmware 1.4.16.2) as well as on the Base
Both are mid 2006 models, The Base is one year old
Symptoms:
Without any change I can remember, the Mini ceased to detect networks (any networks)
All other computers pick up to 11 computers in the area after scanning
I am not able to connect to the home network even if I manually enter the information: if I try to join add a network from scratch and later click on “other” for scanning, the home network will show but if I try to join, it will time out
All Airport settings are identical in both Mini and Book, yet the Book detects and connects with no issue
I am able to set a peer to peer network using the Mini and the Book scans it, detects it and successfully joins – I cannot do the reverse
The network WIFI card displays in the Profiler as active and correct in the systems information entry
And just to reemphasize, the Mini does not detect ANY networks and all the other computers can see up to 11, as well as join the Airport Base without issues
*Troubleshooting so far with the help of Tony Rocco:*
Tried to get rid of all preferred networks and all entries in the key-chain associated with them, and tried again from scratch – No Results
Moved the “SystemConfiguration” folder to the desktop - And restarted the Mini - Keyed in a new Computer Name in the Computer Name field in the Sharing Preferences Pane – No results
Changed Channels on the base – no results

Clearly the problem is only with the Mini. Let's figure out whether it's software or hardware.
Start up from your Leopard install disk. Instead of performing an installation, open Network Utility. (You can access it from the Utilities menu.) Try to connect to your network by selecting it in the AirPort menu.
If no networks appear in the AirPort menu, this is a hardware issue.

IPad2 wifi no longer detecting some networks

Hello, my old iPad 2 is detecting some networks in the house but not others. I have Uverse Motorola ngv510 and using wireless, it has even an additional Cisco WAP for the wireless uverse receivers. My old iPad sees the Cisco WAP but not the standard house wireless, it won't see the HP wireless printer, but the neighbors WAP no problem. My iPad Air sees all of them, it's like the old iPad 2 is just filtering out some WAPs, I've tried manual connections, restarting the Motorola, moving it to just N band, I can't get this old iPad 2 to see my wireless network.
I'm going to take it to work Monday, maybe it will see that one there and I can do an update. It's running iOS 7.0.4
Anyone have this problem that might be able to assist?

Howdy George,
It sounds like you are not seeing all available Wi-Fi networks. I would use the Wi-Fi troubleshooting from the following article, named:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS1398
Restart your iOS device.
Turn your Wi-Fi router off and on2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
Update your device to the latest version of software.
Unable to locate a Wi-Fi network
Verify that the network is available by tapping Settings > Wi-Fi and choosing from the available networks.Note: It may take a few seconds for the Wi-Fi network name to appear.
Move closer to your wireless router (access point) and attempt to locate the Wi-Fi network.
If you do not see the network you would like to join, you may be attempting to connect to a hidden network. Learn how to join a hidden network.
Supported Wi-Fi configurations vary by iOS device model. Find out which standards your device supports3.
Reset network settings by tapping Settings > General > Reset > Reset Network Settings. Note: This will reset all network settings including:
previously connected Wi-Fi networks and passwords
recently used Bluetooth accessories
VPN and APN settings
Thank you for using Apple Support Communities.
Regards,
Sterling

How can I get applications to detect a network scanner?

Running 27" iMac with OS-X 10.7.2, all Software Updates are installed.
Epson Workforce 630 attached via ethernet network. Driver is current at 8.61.
System Preferences>Print and Fax lists the printer and has a tab for the scanner. Scanning via this interface works fine.
Preview will detect and scan without problem, but Image Capture does not detect the scanners. Adobe Acrobat Pro 9 and Pro X do not detect my network scanners. Adobe support is no help. No problems with Apple products appear to be theirs, ever.
Epson drivers according to their website are installed through Software Update -- current.
But Acrobat will not detect the Epson over the network.
Note that my wife's iMac OSX 10.6.8 has the same problem.
Anybody got a clue?
Thanks!
Norm

Surfing Seapearl wrote:
...I pay extra via verizon, so I know it's not the slowest, and I would be aware due to other download speeds. For example, I was able to download adobe flash in a reaonable amt. of time...
You may be paying extra but what speed are you actually getting? Open Activity Monitor, click the Network button at the bottom and watch the Data received/sec speed while you're downloading different things. That will give you the actual transfer rate, not the advertised transfer rate.
Something like Adobe Flash shouldn't take long because it's only about 18 MB; how big is something that seems to lag? Is your internet connection wireless or are you using an Ethernet connection with a Thunderbolt to Ethernet adaptor? Wired is almost always faster. And with Mavericks being over 5 GB, it'll take a while under the best of circumstances, especially since the transfers I've observed of it don't run anywhere near what a fast connection is capable of.

Need HELP my ipod cannot be detected by itunes on my computer even after reset and reinstalling itunes what else can i do?

my ipod touch cannot be detected by my computer or itunes i've reset it and uninstalled/reinstalled itunes and it still detects it as if it's a camera

Try:
iOS: Device not recognized in iTunes for Windows

My macbook pro will no longer detect my network, but my iphome does

i was using my macbook when suddenky the option ti connect to my wifi network is no longer availabke. i have reset my router, and my iPhone still detects the network. idk how to solve this!

Try resetting the SMC and PRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
About NVRAM and PRAM
Try another cable

My iPhone no longer works with my wi-fi network. It detects the network but can't communicate, even though it did so until today for months.

My iPhone no longer works with my wi-fi network. It detects the network but is unable to communicate, even though until today it worked great for months. The network is Verizon FiOS Internet on an M1424WR router. PCs and iPad continue to work with the same network without any problem. Any ideas?

have you upgraded to the new ios5 software? if so that could be the issue and contact apple.

J6450 cannot be detected on network

Similar Messages

Maybe you are looking for