Jabber and Gsm Call status

Is it possible to automatically update presence status to busy in jabber mobile when the user is attending a gsm call?
I've been testing with jabber for iPhone and it doesn't work...

Single DN only I'm afraid. Multi-line is on the roadmap but I can't speak to a timeline.
Please remember to rate helpful responses and identify helpful or correct answers.

Similar Messages

Conference bridging between VoIP and GSM calls

Hello, Can E61/E62/E50/E70 do conference between one call that's running on GSM and second call running through SIP client on VoIP? Thanks, Bilal

I tried to connect the GSM call to VOIP call on E72, but it has not happened.
I presume this may be the case, also there may be a solution for this.
VOIP Connection:
For VOIP calls the network uses an existing external IP address to transfer the information from the a server. The information received vide VOIP shall be transformed into voice which enables us to here the data conveyed by the server.
GSM Connection:
For GSM calls the network uses the intermediate service provider slot to convey the information as a signal throught the network. The signals are the direct output we hear as sound.
By my observation, in my mobile, the two network actions (VOIP and GSM) can be performed instantaneously or simultaneously.
The mobile needs a medium to convert either the GSM output signal (audio) to Internet packet data (bytes) and the VOIP software installed in mobile should recognize the same audio as an input and allow for a conference call.
or
VOIP call get converted into GSM signal.

Jabber and Missed Call history

Hello
I am looking for and explanation or a document around expected behavior for how the Call Log works within the Jabber for Windows client. Our customers setup has Jabber for windows deployed in Deskphone Control mode, where the Jabber clients control a single physical phone. Predominantly a 7945 series phone. How in Sync is the "CALL HISTORY" (missed call, placed call, received call) lists within the Jabber client with the physical phone itself. Examples:
If we miss a call on the physical phone and Jabber is opened, we noticed that both the physical phone and Jabber client report a missing call.
If we miss a call and Jabber is closed, we notice the physical phone reports a missed call, but when Jabber sign's in the "MISSED Call" is not reported on the Jabber client.
Is this expected behavior?
if anyone can provide context or has a document that explains the expected behavior this would be very helpful to me.
Thanks

Jaime,
Just for clarity, I'm not talking about a CSF registered phone, I'm talking about Jabber running in Deskphone Control mode. So yes in a hopeful way I would expect the call history from the physical phones to be in sync since deskphone control is just remotely controlling the phone. I suppose the call history on a physical phone is likely stored locally on the phone itself and this is why they call logs do not remain in sync but i just wanted to confirm that this is a fact vs an assumption.
Thoughts?
Ryan

Jabber 9.2.6 not showing on call status

We have over 400 users on Jabber, and some users do not show status "on call" when on a call
Any solutions?

Is this on-premise IM&P or SaaS WebEx Messenger for a backend?
For on-premise this is done server-side between CUCM and the IM&P cluster. For this to work the end user must be associated to the line appearance of the DN on the device making the call, not the End User Configuration page. Has this been done on that specific line appearance? If yes, does CUCM send the SIP PUBLISH event for that call? You'll need the SDI traces for this. If yes, does the SIP Proxy on CUP receive the event and turn it into an event for the Enterprise Presence Engine?
As you can see this quickly turns into a log review session. Honestly though, it's almost always a misconfiguration in CUCM causing this.
Please remember to rate helpful responses and identify helpful or correct answers.

Jabber and calendar integration

Hi,
I've got two types of Jabber client deployment - on prem and cloud based (this is the old webex connect, not jabber for telepresence). Both have different issues with calendar integration.
On prem Jabber:
1. Presence status is passed to Outlook
2. Calendar appointment whilst they do show up within meeting tab on Jabber client, the status of the client doesnt change to "In a Meeting" during appointments.
Off prem Jabber:
1. Presence status is NOT passed to Outlook
2. Calendar appointments works fine - ie show up in the meeting tab, and status changes correctly.
I have modified AD attribute proxyaddress for on prem clients to SIP:samaccount@cupdomain, I've assumed that for off prem clients, it would be SIP:email@domain as used by login details. I cant seem to find any documentation about calendar integration with webex connect clients.
Any ideas?
Thanks

Hi Elena,
Is it same machine where Outlook integration works with on-prem? If not, there are few things that you could check:
Uninstall other IM clients
Check if any other IM client with Outlook integration has been installed. Many other clients use the same api’s to integrate with Microsoft products and maybe blocking Jabber Click to X. If any other product is installed please uninstall and reboot your machine.
Some applications known to affect Jabber presence integration are: Cisco WebEx Connect, Microsoft Office Communicator, Microsoft Lync, CUCIMOC, CUCILync, Standalone Click to call, Cisco Unified Personal Communicator 8.x.
Registry settings
Confirm the following registry settings exist and are correct:
32-bit machines
Key: HKEY_CLASSES_ROOT\CLSID\{8885370D-B33E-44B7-875D-28E403CF9270}\TreatAs
value (REG_SZ): (Default) = {83CE44B6-A512-4199-9766-38357A9108E8}
-Jabber sets this on install; it replaces the existing class ID with ours
Key: HKCU\Software\Microsoft\Office\12.0\Common\PersonaMenu
value (REG_DWORD type): Enabled = 1, EnablePresence = 2, RTCApplication = 3, SetOnlineStatusLevel = 2, ShowStatus = 1
-Office creates these values on install.
Key: HKLM\Software\Microsoft\Office\Outlook\Call Integration\IMApplication
value (REG_SZ): IMApplication = CiscoJabber.exe
- Jabber sets this value on install, this key is created when office is installed
Key: HKCU\Software\Microsoft\IM Providers
value (REG_SZ): DefaultIMApp = Cisco Jabber
- Jabber sets this value on install
Key: HKCU\Software\IM Providers\ Cisco Jabber
value (REG_DWORD): UpAndRunning = 0 (not running), 1(starting), and 2 (running)
- This key is set by Jabber you do not need to create or manually edit this Registry Key.
- If jabber is running and this key is not set to 2 then there is problem, gather a prt.
64-bit machines
Key:HKEY_CLASSES_ROOT\Wow6432Node\CLSID\{8885370D-B33E-44B7-875D-28E403CF9270}\TreatAs
value (REG_SZ): (Default) = {83CE44B6-A512-4199-9766-38357A9108E8}
-Jabber sets this on install; it replaces the existing class ID with ours
Key: HKCU\Software\Microsoft\Office\12.0\Common\PersonaMenu
value (REG_DWORD type): Enabled = 1, EnablePresence = 2, RTCApplication = 3, SetOnlineStatusLevel = 2, ShowStatus = 1
-Office creates these values on install.
Key: HKLM\Software\Wow6432Node\Microsoft\Office\Outlook\Call Integration\
value (REG_SZ): IMApplication = CiscoJabber.exe
Key: HKCU\Software\Wow6432Node\IM Providers\Cisco Jabber
value (REG_SZ): Friendly Name = Cisco Jabber
value (REG_SZ): GUID = {83CE44B6-A512-4199-9766-38357A9108E8}
value (REG_SZ): ProcessName = CiscoJabber.exe
Key: HKCU\Software\IM Providers\Cisco Jabber
value (REG_DWORD): UpAndRunning = 0 (not running), 1(starting), and 2 (running)
- This key is set by Jabber you do not need to create or manually edit this Registry Key.
- If jabber is running and this key is not set to 2 then there is problem, gather a prt.
If all is in order, then open a support case with Cisco TAC and provide logs as below:
Enabling Outlook logging
Setting this registry data enables logging for the presence features that integrate between Outlook and Jabber, and shows additional information in Outlook and Jabber. To set this registry key, do the following:
Click Start, and then click Run.
In the Open box, type REGEDIT, and then click OK to start Registry Editor.
Navigate to key: HKEY_CURRENT_USER\Software\IM Providers.
Create DWORD: OfficePresenceLogging with Value: 1.
If it does not exist already, manually create %userprofile%\Tracing directory, otherwise the log files will not be created.
Restart Outlook.
The log file is created in the %userprofile%\Tracing folder and the file name will be OfficePresence-#.log (where # is an integer). The last modified date will indicate which file is the latest.
Create a Jabber Problem Report (PRT)
Recreate the issue.Do this by opening the email\SharePoint page that shows the problem, select an example user, show their contact card.
Take screenshots of the issue and record time stamps.
Take note of the User names and email address\IM address of the problem users.
Go to your Jabber client and select Help > Report a problem, and then follow the steps to produce the problem report.
Thanks,
Maqsood
Uninstall other IM clients
Check if any other IM client with Outlook integration has been installed. Many other clients use the same api’s to integrate with Microsoft products and maybe blocking Jabber Click to X. If any other product is installed please uninstall and reboot your machine.
Some applications known to affect Jabber presence integration are: Cisco WebEx Connect, Microsoft Office Communicator, Microsoft Lync, CUCIMOC, CUCILync, Standalone Click to call, Cisco Unified Personal Communicator 8.x.

Jabber and Voicemail Access

Hello,
I've configured CUCM and IM&P v9.1 and jabber client 9.2(1), the chat and the calls work fine but when I try to log in Phone Accounts -> Voicemail I get an error about the credentials, I have all integrated with Active Directory and the user and password that I'm using for voicemail is the same that I use to log in the jabber client wich worked fine.
Here I attached the error screen.
What do you think can be causing this??
Thanks in advance.

Hi every body,
I have some problems but not with all the users, is only working with 3 users and the rest of them don't work, I attached the errors that I get when I try to log in Telephony Accounts in the Jabber, I used the Jabber of one User, and from here I introduce my credentials (user and password) and I can get the voice mails (only from de 3 users that is woriking fine), but when I introduce the credentials of the other user I get the error and Can't get the voicemails.
The 127.23.0.7 is the IP address of the Cisco Unity Connection.
Please Help Me I'm stuck with this!

Jabber and O365 integration

Hello,
Do we need any additional licenses from Cisco or Microsoft to make a full possible integration between O365 and Jabber ?
For example features like :
Single Inbox Unified Messaging with SpeechView transcriptions, Microsoft Word Click to Call, SharePoint Presence & Click to Call, Jabber video calling and desktop sharing, and WebEx on desktop and iPad,
Thank you for your help
Best Regards,
Tomasz

Tomek,
There is no direct integration between Jabber and Office 365, except for Exchange Gateway integration on IMP server side which is not supported with Office 365. All other Jabber integrations do not go to Office 365, calendar client integrations are done with Outlook, and UM integration is between Office 365 and Unity Connection, which does not affect Jabber.
HTH,
Chris (Krzysiek) :-)

Jabber and Desk Phone

Hello guys,
I've configured CUCM and IM&P v9.1 and jabber client 9.2(1), the chat works fine and also the Cisco Unified Client Services Framework Device can make and receive calls but if I try to select the desk phone for calls it just keeps trying to select it but it doesn't work.
Is there and special config besides the normal CUCM and IM&P v9.x integration in order to use the desk phone????
What do you think can be causing this??
Thanks in advance for your help.

Hello Joshua,
I tried to login to the x.x.x.x/ciscopca (with the Unity's IP) and it didn't work, I have my cucm integrated with ldap and in my cuc I imported the users from the cucm. It seems that the authentication using the ldap users is broken in the cuc.
What do you think can be causing this??
Thanks in advance.

Jabber and Desk Phone Integration

When stting up "Desk Phone Integration" on cisco Jabber on a test iPhone, Jabber loops forever when verifying account information saying just "verifying...". It never display an error message. It will eventually stop, the "Desk Phone Integration" staying "Not Configured"
CUCM version : 8.6(2)
iPhone iOS : 6.0.1
Jabber client : 9.0.2.20078
I followed the instructions in the "Administration Guide for Cisco Jabber for iPhone Release 9.0.1" to setup the call manager.
I created a dedicated SIP profile,
created the TCTTEST "Cisco Dual Mode for iPhone" phone according to the documentation
and edit my phone and user settings according to the "Enable Active Call Transfer Between Cisco Jabber and Desk Phone" section of the documentation
despite all that, it doesn't work
I tried with other accounts/mobiles and the result is the same.
Jabber does register to the CUCM and I can get my extension on the Jabber client and place/receive calls using my desk extension. But the "desk phone integration" doesn't work
What I noticed is that :
on the TCTXXXX "Cisco Dual Mode for iPhone" phone device setting page, there is no "Sign In Feature" option as described in the documentation
because we use Extension mobility the "Owner User ID" feature is disable on the desk phone device settings. I temporarily uncecked the "extension mobility" checkbox on the device, setup my ID as the "Owner User ID" and re-checked the "extension mobility" checkbox but the result is the same.
I searched the web and couldn't find anyone with similar issue...help will be appreciated

Aaron,
Thanks for you answer.
I have followed all the requirements explained in the "Administration Guide for Cisco Jabber for iPhone Release 9.0.1" including the one you mentioned :
the user is a member of 'Standard CTI Enabled'
CTI Controlled is allowed on the DN, the end user account and the desk phone
the end user is associated to both the desk phone and the TCT phone
And 'Allow End User Configuration Editing' is set to disable on the TCTxxxx device
Despite all that the "desk phone integration" doesn't work

Jabber For Windows - Available Status on Hibernation

We're running Jabber for Windows 9.1.1 ansd see an issue which I think is casued by hiberantion.
A laptop user will be at their pc and and Available, then on leaving their desk, they would typically just close their pc lid, hibernating the pc, and leave the building.
Their status stays as Available, when of course thay are not. I understand that CUP has not received a specific state change event to update their status, but does any one know if their is a timeout/keepalive that would eventually indicate the user is offline?
I've not had chance test this in detail yet, I've just noticed it a few times when users near me are no longer at their desk, but still show as available.
Has anyone out there come across this? Or do I need to be telling our users they should sign out of Jabber before hibernating their pc's?
Regards
Kelvin

Hi All,
We have also been suffering from this issue ( I supect) - Running 9.1.2 client but it is also in 9.1.1. Same CUPS 8.6 version etc.
Closing my PC lid - PC Asleep
I can been seen as Away from another PC.
Opening my PC lid - I am still seen Away - both on my own jabber and a watcher client. I haven’t logged out and my status does not change even when I am back on the keyboard etc.
I can change it manually and then its appears correct both on my PC and the other PC.
Or
If I log out of jabber and back in – the correct status is shown both locally and remotely.
This appears confusing to the end user who thinks presence isn't working correctly. we have a number of jabebr users that move between locations for meetings and hence often just close thier PC lid and move locations. FYI - this also happens within the same site.
can you advise if there is a TAC case and if so if we can get an update ?
thanks
Russ

Calling 'Status' screen of transaction IW32 from report

Hi,
I want to display 'status overview' screen from transaction 'iw32' .
I know how to call transaction 'iw32', but I don't know how can
I directly go on status screen? I have order no with me.
Can anyone help me?

Hi,
You can get the user status data directly from the following tables:
Pass on the order number to JEST table to fetch the STAT (status) for which INACT field is a blank (means status those are active in the order). You will find the status in the form of E001 or I001 depending upon the user status or system status respectively.
Now goto TJ30T table where you need to pass the status profile (STSMA) which can recovered from the order number and fetch the status text by comparaing ESTAT with the status received from JEST table. Field TXT04 in TJ30T gives the status text.
Hope you will find this helpfull.

ACD Logs Display and Agent Call Display is N/A on CSD

Hello,
We are facing the problem that the ACD logs display and Agent call display is N/A on the Cisco Supervisor Desktop. The version of CSD is 8.5.4, overall status of CSD is fine, for reference please see the attached screenshot.Thanks.
Looking forward for the response.
BR,
Durraze

Hi Karthi,
On PGA run the postinstall.exe setup turn off/on the Rascal Replication setup, in services.msc cycle the services shared below:
Cisco Chat Service
Cisco Enterprise Service
Cisco LDAP monitor service
Cisco License and Resource management
Cisco Recording and Playback
Cisco Recording and Statistics Service
Cisco Sync Service
Cisco VOIP monitor
Please rate if it helps.
BR,
Durraze Khan

Incomng and Outgoing calls are stop routing every five min

Dear Team,
Please find the attached running config and logs.Incoming and outgoing calls are landing on the gateway properly. But call stop working every five min.PRI is up and no error on controller E1.
Please advise how to identify the issue?
CUCM version 4.2
debug isdn q921
*Sep 2 08:48:21.874: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=2 nr=34
*Sep 2 08:48:21.890: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=3
*Sep 2 08:48:21.942: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=34 nr=3
*Sep 2 08:48:21.942: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=35
*Sep 2 08:48:27.866: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=35 nr=3
*Sep 2 08:48:27.866: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=36
*Sep 2 08:48:34.322: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=36 nr=3
*Sep 2 08:48:34.322: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=37
*Sep 2 08:48:34.326: %ISDN-6-CONNECT: Interface Serial0/0/1:27 is now connected to 0503726912 N/A
*Sep 2 08:48:34.326: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=3 nr=37
*Sep 2 08:48:34.342: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=4
*Sep 2 08:48:39.694: %ISDN-6-DISCONNECT: Interface Serial0/0/1:29 disconnected from 0094777382372 , call lasted 181 seconds
*Sep 2 08:48:39.698: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=4 nr=37
*Sep 2 08:48:39.706: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=5
*Sep 2 08:48:39.730: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=37 nr=5
*Sep 2 08:48:39.730: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=38
*Sep 2 08:48:39.734: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=5 nr=38
*Sep 2 08:48:39.746: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 voice-port 0/1/2
*Sep 2 08:48:49.746: ISDN Se0/0/1:15 Q921: User TX -> RRp sapi=0 tei=0 nr=38
*Sep 2 08:48:49.758: ISDN Se0/0/1:15 Q921: User RX <- RRf sapi=0 tei=0 nrsh
*Sep 2 08:48:59.762: ISDN Se0/0/1:15 Q921: User TX -> RRp sapi=0 tei=0 nr=38
*Sep 2 08:48:59.766: ISDN Se0/0/1:15 Q921: User RX <- RRf sapi=0 tei=0 nr
*Sep 2 08:49:01.946: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=38 nr=6
*Sep 2 08:49:01.950: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=39
*Sep 2 08:49:01.950: %ISDN-6-DISCONNECT: Interface Serial0/0/1:27 disconnected from 0503726912 , call lasted 27 seconds
Voice-Gw#
Voice-Gw#
Voice-Gw#
Voice-Gw#
*Sep 2 08:49:01.954: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=6 nr=39
*Sep 2 08:49:01.962: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=7
*Sep 2 08:49:02.034: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=39 nr=7
*Sep 2 08:49:02.034: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=40
controller E1 0/0/1
pri-group timeslots 1-31
interface Serial0/0/1:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
=======================
Voice-Gw#
*Sep 2 08:55:25.214: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=71 nr=27
*Sep 2 08:55:25.214: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=72
*Sep 2 08:55:25.234: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=27 nr=72
*Sep 2 08:55:25.246: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=28 nr=72
*Sep 2 08:55:25.250: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=28
*Sep 2 08:55:25.258: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=29
*Sep 2 08:55:27.518: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=72 nr=29
*Sep 2 08:55:27.518: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=73
*Sep 2 08:55:27.522: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=29 nr=73
*Sep 2 08:55:27.534: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=30
*Sep 2 08:55:27.546: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=73 nr=30
*Sep 2 08:55:27.546: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=74
*Sep 2 08:55:33.318: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=30 nr=74
*Sep 2 08:55:33.330: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=31
*Sep 2 08:55:33.390: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=74 nr=31
*Sep 2 08:55:33.394: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=75
*Sep 2 08:55:37.190: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=75 nr=31
*Sep 2 08:55:37.194: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=76
*Sep 2 08:55:38.534: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=76 nr=31
*Sep 2 08:55:38.534: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=77
*Sep 2 08:55:38.538: %ISDN-6-CONNECT: Interface Serial0/0/1:27 is now connected to 0504312690 N/A
*Sep 2 08:55:38.538: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=31 nr=77
*Sep 2 08:55:38.554: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=32
*Sep 2 08:55:42.542: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=32 nr=77
*Sep 2 08:55:42.554: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=33
*Sep 2 08:55:42.606: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=77 nr=33
*Sep 2 08:55:42.606: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=78
*Sep 2 08:55:46.766: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=78 nr=3
% Invalid input detected at '^' marker.
Voice-Gw#sh controllers e1 0/0/1
E1 0/0/1 is up.
Applique type is Channelized E1 - balanced
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20060711, FPGA: 13, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (99 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Voice-Gw#
Voice-Gw(config)#do sh isdn statu
Global ISDN Switchtype = primary-net5
ISDN Serial0/0/0:15 interface
        dsl 0, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
        DEACTIVATED
    Layer 2 Status:
        TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
        0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask: 0x00000000
    Number of L2 Discards = 0, L2 Session ID = 0
ISDN Serial0/0/1:15 interface
        dsl 1, interface ISDN Switchtype = primary-net5
    Layer 1 Status:
        ACTIVE
    Layer 2 Status:
        TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
    Layer 3 Status:
        3 Active Layer 3 Call(s)
        CCB:callid=E3C0, sapi=0, ces=0, B-chan=30, calltype=VOICE
        CCB:callid=E3C6, sapi=0, ces=0, B-chan=31, calltype=VOICE
        CCB:callid=E3CB, sapi=0, ces=0, B-chan=29, calltype=VOICE
    Active dsl 1 CCBs = 3
    The Free Channel Mask: 0x8FFF7FFF
    Number of L2 Discards = 0, L2 Session ID = 2
    Total Allocated ISDN CCBs = 3

Hi.
Can you please also attach a CUCM trace during a disconnected call?
Thanks
Regards
Carlo

How do i test a record containing status E0008 and not containing status I0002

hello all,
how do i test a record containing status E0008 and not containing status I0002 for a given WBS Element....
the data(like pspnr, posid and objnr from table PRPS are avialable in internal table it_prps)....

Hi,
You can check the received table from the function module as per your condition.
loop at it_prps.
     call function STATUS_READ and pass objnr
          "suppose tables parameter data is in table itab
     Read table itab with key STAT = 'E0008'. "check for E0008
       if sy-subrc = 0.
          read table itab with key stat = 'I0002'. "if E0008 exists then check for I0002
               if sy-subrc = 0.
                   "both status E0008 & I0002 exists so delete this record from it_prps
                    delete it_prps.
               else.
                   "only status E0008 exists.
               endif.
     endif.

Voip settings disturbing gsm call.

Hello !
I've installed voip settings application on my n85 and set up a sip profile and it's working pretty good.
I activate this profile whenever i need it via the contacts application.
But everytime i'm having a phone call via the gsm network, the phone connects to the internet (arrows below 3G) even if my sip profile is not activated.
It stops doing this if i delete the sip profile.
So what data are being exchanged when i'm having a simple gsm call ?
And is it possible to stop this (other than using fring...)
Thanks a lot ;-)

I recommend you visit the following page:
http://www.developer.nokia.com/info/sw.nokia.com/id/d476061e-90ca-42e9-b3ea-1a852f3808ec/SIP_VoIP_Se...
more info here:
http://www.developer.nokia.com/Resources/Tools_and_downloads/Other/SIP_VoIP_settings_applications.xh...
Here is also the manual for SIP VoIP Settings User Guide v1.1
http://www.developer.nokia.com/info/sw.nokia.com/id/c8824cfe-fff7-4fde-af62-da21a8938de2/SIP_VoIP_Se...
and also SIP VoIP 3.x Settings v2.0
http://www.developer.nokia.com/info/sw.nokia.com/id/b1c361a2-7eb2-4853-8c0c-d2f54e184237/SIP_VoIP_3_...

Jabber and Gsm Call status

Similar Messages

Maybe you are looking for