Jabber login from public network not working

Hello all,
i am trying to register jabebr from public network with use of EXP-C and E.
but facing below error:

thanks fro your response to correct me with configuration.
1) Configuration as it pertains to the design on the Expressways
i applied as per design and still open all ports between firewall for jabber.
2) Firewall blocking the UDP traffic.
if no rule define, how can it block and what need to configure for jabber with audio?
First question to you is are you using Single NIC or Dual NIC on the Expressway-E?
i am using single NIC.
If you are doing a Single NIC design and will have a private IP for the Expressway-E you must fulfill these 4 requirements
1)   Static NAT Mode Enabled on the IP Configuration page of the Exp-E
i will enable it on EXPE>.
2)   Static NAT Address Configured on the IP page of the Exp-E
what need to EXPE for this NAT option?
3)   Expressway-C must resolve the Expressway-E FQDN to the Public IP, not the private
if this is resolving private ip, would be any problem?
4)   NAT Reflection (Hairpinning) must be configured on the firewall so that traffic from the Expressway-C can be sent to the Expressway-E public IP and that can be redirected to the Expressway-E private IP. Please note not all firewalls support this functionality
please tell me how can enable NAT reflection on firewall to working it?
thanks

Similar Messages

How does Distribution/collection from a network folder work?

I sorry if this has been asked before, but i need a basic understanding of how Distribution/collection from a network folder works. To give you an idea what I need, i'll tell you that Arcobat 9 was purchased by a couple people at work, and they are asking me to figure this out. I'm a web guy and know enough about pdf's to throw one on a web server and put a link to it somewhere. I don't know anything about Acrobat otherwise.
So, If someone can give me a basic overview of how this works, I would really appreciated it. I'm assuming that Acrobat sets up some kind of email server on the user's computer and has a database in it some where.
Thanks

Jan,
I have attached a simple example that uses "Basic Level Trigger Detection.vi" found in the Analyze->Waveform Monitoring menu. You can change the slope from rising to falling edge to note the change in the result.
I was unable to find the "Simple Trigger Detection.vi" that is giving you trouble. If you would like you can attach a piece of code that replicates your problem. Please make sure to include all subvi's in the attachment (including the Simple Trigger Detection.vi). I can take a look to see what is going on.
Thanks.
Matt Kisler
Applications Engineer
National Instruments
http://www.ni.com/ask
Attachments:
8889.vi ‏36 KB

MacBook Air wifi internet shared network not working on tethered android phone GT B5122

MacBook Air wifi internet shared network not working on tethered android phone GT B5122
I have created a password protected wifi internet network on my Macbook air. I tethered by Andriod phone onto this network, but the internet connection works intermittently on the phone, and when it stops working the network continues to show as connected to the shared network mostly(other times it keeps renewing the wifi IP address on the Andriod phone).
Also the network the MBA is connected to, is a hardwired one using a SSH login account in a student accomadations.
I am not sure, but all the restarting and refreshing of system, phone and wifi sharing and re-enabling wifi is not reparing the internet connecting on the wifi network for the phone
Really puzzled, if this is one of the Apple, Andriod compatability issues.
Cheers,
Vivek

Spanners91 wrote:
Hi.
I'm having trouble with the wireless connection on my new home hub 3. Most devices will connect easily, but there are three devices that have trouble connecting. These are an Android Phone (Samsung Galaxy Mini), an android tablet (Sony Tablet S) and an iPod. All of these devices work perfectly on other network connections, and other devices in the house are quite happy connecting to the network.
The Androids can see the network, and will try to connect to it, but when they do they just go through a loop of "connecting">>"acquiring IP address">>"disconnected". I have tried resetting the Home Hub with a pin, and that lets the devices connect for about 24 hours, but after that time they stop connecting again.
I'm really not sure what to do to fix the problem, so I will very much appreciate some help.
Many Thanks.
My lads SGMini connects perfectly to our hub3
Have you installed the BTFon app to these devices?
If so, you could delete it and then see what hapens.....
-+-No longer a forum member-+-

Consuming PI Webservice from Webdynpro Java Not working

Hello SAP,
Environment: CE 7.2.
Resolution expected immediately, Helpful answer is highly appreciated.
Is the namespace should not exceed 60char for PI Webservice, for executing the webservice from Webdynpro Java.
I tried with all the options in executing the PI Service from Webdynpro Java, None of the options worked. I am facing the below error while I was calling the PI Webservice.
I don't see any problem from Webdynpro Java, what ever the procedure I have followed is the standard procedure.
Fortunately when I execute the service from Webservice Navigator, it is working as expected. The same webservice when I consume it from Webdynpro Java it is not working
Options tried so far:
1) Published the Services to Service Registry and there by consuming the PI Service from Service Registry - Not worked
2) Tweaked the URL with few options - Not worked (Tweaking the URL, ex: portType, Binding)
3) Changing the Business Systems in PI and there after calling the service - Not worked
4) Initializing the code, instead of creating Service Controller and calling the PI Service - Not worked.
5) Created a Provider System and tried to call the PI Webservice from Provider System - Not Worked
For all the Options, I am facing the same error which is provided in the screenshot.
Below procedure which I have followed for calling the PI Webservice:
1) Created Adaptive Webservice Model
2) Provided PI Webservice URL (It prompts for PI System UserId and Password)
3) Selected Option - No Service Group Configuration
4) Provided Logical Destination
6) Completed creation of Model
7) Added the model as a UsedModel
8) Right Click on Comp Contr. and selected Apply Template and Created a ServiceController for the model (Entire mapping to comp contr, Initializing the nodes is taken care by Service Contr.)
9) Created an Template Action button and there by calling execute method which is auto rendered from CompContr..
10) Build the project.
11) Activated the code and Run the Application.
12) Getting the below error which is showed in the message.
ERROR MESSAGE:
Exception on execution of web service on destination 'GetPIHRPeopleData' for operation 'SI_CreateHRPeopleData_OS' in interface 'SI_CreatePeopleCompany_OS'

Hi Sankar,
If the webservice is working fine in the Wsnavigator then there is some problem with importing the webservice in webdynpro for Java. Please check the required parameter for creating the Adaptive Webservice Model. After adding in the used model and compoent controller binding, you need to write code for to execute the webservice model.
Please check the code for initialization and execution for the webservice and then test it.
Best Regards,
Arun Jaiswal

Select * from tab is not working in oracle 10g

select * from tab is not working in oracle 10g. But at the same time,
select * from <<table>> is working.
Please advise me.

This works for me in 10.2.0.2
Connected to:
Oracle Database 10g Enterprise Edition Release 10.2.0.2.0 - 64bit Production
With the Partitioning, OLAP and Data Mining options
SQL> select * from tab;
TNAME                          TABTYPE            CLUSTERID
LOAN_DETAIL                    TABLE
PLAN_TABLE                     TABLE
...

When I unplug Apple headphones from my MacBook Pro sond from internal speakers not work, and system soud preferences displayed: Output: optical digital out port only

When I unplug Apple headphones from my MacBook Pro sond from internal speakers not work, and system soud preferences displayed: Output: optical digital out port only

If you see a red light in the audio output port, then the internal switch is stuck. Insert the earphone plug a few times and see if you can trip the switch. If that fails, insert a cocktail stirrer and the like and jiggle it around inside. If that fails, take it to an Apple store and have the technicians at the genius bar do it for you.
Ciao.

Need to re-install CS5.5 on my new hard drive. Serial number from disk package not working.

I need to re-install CS5.5 on my new hard drive. Serial number from disk package not working.

if there's a problem with the number of installations, you'll see a message about an excess activation problem.
if that's what you're seeing, contact adobe support for an activation count reset, https://helpx.adobe.com/contact.html
otherwise, attach a screenshot of the error message or quote it.

Get-MailboxSentItemsConfiguration Set-MailboxSentItemsConfiguration From Only (still) not working

Hello,
I would like to ask a question, hopeing it is resolved in some way and i missed it.
I have installed SP3 Rollup 4 on our Exchange 2010 server.
This added 2 new Powershell commands
Get-MailboxSentItemsConfiguration
Set-MailboxSentItemsConfiguration
This can be used to manipulate where mail is stored in the send items.
Sender - e-mails sent using SendAs or Send-on-Behalf-of permissions are saved only in the Sent Items folder of the Sender (UserA);
SenderAndFrom – e-mails sent using SendAs or Send-on-Behalf-of permissions are saved in the Sent Items folder of the Sender and the mailbox on which the permissions are assigned (in our example, both UserA and UserB);
From – e-mails sent using SendAs or Send-on-Behalf-of permissions are saved in the Sent Items folder of only the mailbox on which the permissions are assigned (in our example, UserB)
What we really want it to use the From only way.
We use a shared team mailbox and use that as primary, as a second mailbox users get a trusted non shared mailbox. Mail sent from the trusted mailbox should only be in the send items from the actual sender, not both.
2 sites report that the From field is reserved for Future Use, or bugged and does not work is intened.
Here is is stated on 1 July 2013
http://technet.microsoft.com/en-us/library/jj884078(v=exchg.141).aspx
From Reserved for future use. To save the messages sent as this mailbox in the Sent Items folder of this mailbox, use SenderAndFrom value.
That was on 26 March 2013
http://www.msexchange.org/kbase/ExchangeServerTips/ExchangeServer2010/OutlookOWA/sent-items-behavior-shared-mailboxes-update.html
NOTE 1: the From value does not work as expected... It basically performs the same action as the SenderAndFromvalue, meaning it saves the e-mail in both mailboxes. This is still the case in Rollup 5 v2.
We are on 3 March 2014 now, is this still bugged, did i miss something, or is there an ETA when this will be fixed ?
Looking foward to any replies.
Kind regards,
Jeroen van Velzen

I am using a shared mailbox (with a disabled account) where I get sent items and also deleted items placed in the right folders.
I think it’s just a matter of how you configure Outlook. It works well for me in both Outlook 2010 and Outlook 2013, cached mode and also online mode. You can add a shared mailbox to your Outlook profile in at least two ways where one of them doesn’t work
but the other does.
If you add the shared mailbox via the File tab/Account settings/New/ and just enter the e-mail address of the shared mailbox in the Auto Account Setup page. No name, no password, just the e-mail address and click Next and voila “Your e-mail account is successfully
configured”. After restarting Outlook you will find the shared mailbox below your own in the left pane.
If you click the inbox ones in the shared mailbox and then open a new mail you will see the shared mailbox display name in the From field. After sending the mail you will see the mail in the Sent Items folder of the shared mailbox. If you delete a mail in
the shared mailbox you will see it in Deleted items folder of the shared mailbox.
The prerequisits for this is that you have “full access” and “send as” rights of the shared mailbox.
This was accomplished without using the Set-MailboxSentItemsConfiguration command.
We are running Exchange 2010 SP3 RU4.

PIX 501 config - access to internal network not working from remote VPN users - everything on the inside is OK

One other thing - I had a problem with the key pairing so I rebuilt the rsa 1024 and the unit started working. Unfortunately I reloaded without the config in place and now I cannot get it to work again. Any help will be greatly apprecaited although I did review a dozen other posts of people having similar problems and for some reason there is never any conclusion as to the solution and I am not sure why.
Some other info from the client end:
I just ran the stats on the client and packets are being encrypted BUT none are decrypted.
Also Tunnel received 0 and sent 115119
Encryption is 168-bit 3-DES
Authentication is HMAC-SHA1
also even though the allow LAN is selected in the Cisco VPN client it states the local LAN is disabled in the client stats
also Transparent tunneling is selcted but in the stats it states it is inactive
I am connecting with the Cisco VPN Client Ver 5.0.07.0440
This config works. It is on the internal net 192.168..40.x and all users obtain dhcp and surf the web. It has required ports opened.The problem is that you can connect remotely via the VPN and you receive an IP address from the remote-vpn pool but you cannot see any machines on the internal network. The pix is at 40.2 and you cannot ping the pix and the pix from the remote PC connecting via the VPN and youcannot ping the remote PC from the PIX console when the remote is connected and receives the first IP address in the VPN pool of 192.168.40.25
I need to see the internal network and map network drives. I have another friend that is running the same config and it works but his computer is on a linksys wireless and has an IP of 192.168.1.x and the IP he receives from the VPN pool is 192.168.1.25 so I do not know if the same network is allowing this config to work even if there is an error in the config. In my present case I obtain the ip of 192.168.40.25 from the VPN pool and my connecting pc on 192.168.1.x I really am not sure how the VPN virtual adapter works. I am assuming it routes all traffic from your connecting PC to and from the virtual adapater but I really do not know for sure.
Other people have had similar issues with accessing the internal network from the VPN. One solution was the split-tunnel, another was the natting and another had to do with the encrption where there and an issue with the encrypt and ecrypt which was stopping the communicaton via the VPN.
I still cannot seem to find the issue with this config and any help will be greatly appreciated.
This is the config
interface ethernet0 100full
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password somepassword
hostname hostname
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
object-group network internal_trusted_net
network-object 192.168.40.0 255.255.255.0
object-group icmp-type icmp_outside
icmp-object echo-reply
icmp-object unreachable
icmp-object time-exceeded
icmp-object source-quench
access-list OutToIn permit icmp any xxx.xxx.xxx.0 255.255.255.248 object-group icmp_outside
access-list no_nat_inside permit ip 192.168.40.0 255.255.255.0 192.168.40.0 255.255.255.0
access-list split_tunnel permit ip 192.168.40.0 255.255.255.0 192.168.40.0 255.255.255.0
access-list OutToIn permit ip any any
access-list outbound permit ip any any
(NOTE: I had many more entries in the access list but removed them. Even with the above two allowing everything it does not work)
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside xxx.xxx.xxx.xxx 255.255.255.248
ip address inside 192.168.40.2 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool vpn_client_pool 192.168.40.25-192.168.40.30
pdm history enable
arp timeout 14400
global (outside) 1 interface
I had this statement missing from the previous posted config but even with the nat (inside) 0 access-list no_nat_inside it still does not work.
nat (inside) 0 access-list no_nat_inside
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
access-group acl_outside_in in interface outside
access-group outbound in interface inside
route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
http server enable
http 192.168.40.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community $XXXXXX$
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set 3des_strong esp-3des esp-sha-hmac
crypto dynamic-map clientmap 50 set transform-set 3des_strong
crypto map vpn 50 ipsec-isakmp dynamic clientmap
crypto map vpn client configuration address initiate
crypto map vpn client configuration address respond
crypto map vpn client authentication LOCAL
crypto map vpn interface outside
isakmp enable outside
isakmp identity address
isakmp client configuration address-pool local vpn_client_pool outside
isakmp nat-traversal 20
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption 3des
isakmp policy 10 hash sha
isakmp policy 10 group 2
isakmp policy 10 lifetime 86400
vpngroup remote-vpn split-tunnel split_tunnel
vpngroup remote-vpn idle-time 10800
vpngroup remote-vpn password ANOTHER PASSWORD
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh 192.168.40.0 255.255.255.0 inside
ssh timeout 30
console timeout 60
dhcpd address 192.168.40.100-192.168.40.131 inside
dhcpd dns xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd enable inside
username AUSER password PASSWORD privilege 15
terminal width 80
****************** End of config
I have been searching docs and other people's postings trying to obtain the info to make this work. It appears pretty much boiler plate but I believe my problem is in the natting. I am using a range in the internal network for the VPN pool and I have tried switching this to other networks but this has not helped. Unfortunately I have been unable to get the PDM to work and I believe this is a PC config thing and I did not want to waste the time on it. I read a post where a person using the PDM interface with the same problem (not being able to access the internal network) was able to go to a section in the VPN wizard and set the Address Exeption Translation. They said they originally set the VPN subnet when they did not have to. Many of the other blogs I read also stated that if the natting is not proper for the VPN pool- that it will not work but I am confused by the examples. They show as I do the complete range for an access-list called no_nat_inside but I believe it should only have the VPN pool IP range and not the entire network since the others do require natting - not sure if my thought process is correct here. Any help will be greatly apprecaited. Also this morning I just tried a boiler plate example from CISCO and it also did not do what I need for it to do. And I also connect a PC to obtain an IP to see if I can see it - no good. The PC can ping the PIX and viceversa but no one can ping the remote PC that connects via the CISCO Remote VPN client even though it receive an address from the vpnpool. Also include LAN is checked off on the client. This was mentioned in anther post.
Thank you once again.

Hi,
PIX501 is a very very old Cisco firewall that has not been sold for a long time to my understanding. It also doesnt support even close to new software levels.
If you wanted to replace the PIX501 the corresponding model nowadays would be ASA5505 which is the smallest Cisco ASA firewall with 8 switch port module. There is already a new ASA5500-X Series (while ASA5505 is of the original ASA 5500 Series) but they have not yet introduced a replacing model for this model nor have they stopped selling this unit. I have a couple of them at home. Though naturally they are more expensive than your usual consumer firewalls.
But if you wanted to replace your PIX firewall then I would probably suggest ASA5505. Naturally you could get some other models too but the cost naturally rises even more. I am not sure at what price these are sold as used.
I used some PIX501 firewalls at the start of my career but have not used them in ages since ASA5505 is pretty much the firewall model we use when we need a firewall/vpn device for a smaller network/branch site.
Here is a PDF of the original ASA5500 Series.
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/prod_brochure0900aecd80285492.pdf
Here is a PDF of the new ASA5500-X Series
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/at_a_glance_c45-701635.pdf
I am afraid that its very hard for me atleast to troubleshoot this especially since I have not seen any outputs yet. Also the very old CLI and lack of GUI (?) make it harder to see what the problem is.
Could you provide the requested outputs?
From the PIX after connection test
show crypto ipsec sa
Screen captures of the VPN Client routing and statistics sections.
- Jouni

Custom DB authentication to an application from Oracle Portal not working.

Hi All,
We have a Portal customized and integrated to LDAP for SSO.
From the portal, we have a link that takes to another custom application that requires another level of authentication. We have implemented this authentication as custom Database based authentication.
When user login to the portal and access this link, he will be directed for authentication again. This custom application has been installed on a different OC4J instance while Oracle Portal is running in a different OC4J instance.
Issue is though user details are being propagated to the custom application page, we are receiving an error saying authentication failed.
In the OC4J instance specific for this custom application, we have configured jazn.xml to use custom authentication.
Below is the code:
<?xml version = '1.0' encoding = 'UTF-8' standalone = 'yes'?>
<!DOCTYPE jazn PUBLIC "JAZN Config" "http://xmlns.oracle.com/ias/dtds/jazn-9_04.dtd">
<jazn provider="XML" location="./jazn-data.xml" default-realm="jazn.com">
<property name="role.mapping.dynamic" value="true"/>
<property name="custom.loginmodule.provider" value="true"/>
</jazn>
and in jazn-data.xml, we gave the role mapping.
But the problem is when the link to the custom application is accessed, it seems like the custom autentication mechanism is not working.
Can anyone throw light on this?
Do we need to give the same configuration in the j2ee/home/config directory files also?
Can we use both LDAP and custom DB authentication with in the same OAS setup. Remember as of now, Portal and custom application are running in different OC4J instances but within the same OAS.
Any help in this regard will be highely appreciated.
Thanks,
Sasi Bhushan

Hi All,
We have a Portal customized and integrated to LDAP for SSO.
From the portal, we have a link that takes to another custom application that requires another level of authentication. We have implemented this authentication as custom Database based authentication.
When user login to the portal and access this link, he will be directed for authentication again. This custom application has been installed on a different OC4J instance while Oracle Portal is running in a different OC4J instance.
Issue is though user details are being propagated to the custom application page, we are receiving an error saying authentication failed.
In the OC4J instance specific for this custom application, we have configured jazn.xml to use custom authentication.
Below is the code:
<?xml version = '1.0' encoding = 'UTF-8' standalone = 'yes'?>
<!DOCTYPE jazn PUBLIC "JAZN Config" "http://xmlns.oracle.com/ias/dtds/jazn-9_04.dtd">
<jazn provider="XML" location="./jazn-data.xml" default-realm="jazn.com">
<property name="role.mapping.dynamic" value="true"/>
<property name="custom.loginmodule.provider" value="true"/>
</jazn>
and in jazn-data.xml, we gave the role mapping.
But the problem is when the link to the custom application is accessed, it seems like the custom autentication mechanism is not working.
Can anyone throw light on this?
Do we need to give the same configuration in the j2ee/home/config directory files also?
Can we use both LDAP and custom DB authentication with in the same OAS setup. Remember as of now, Portal and custom application are running in different OC4J instances but within the same OAS.
Any help in this regard will be highely appreciated.
Thanks,
Sasi Bhushan

File Sharing on the Network not working properly

Hoping someone can help and not really sure if its the right place to ask but I am totally at a loss so thought I would give it go. Technically it is an issue with logging onto the Shared Folders from a Media Player but not sure if the issue has been caused by settings on the Mac.
I have an IMAC with shared folders that can be accessed on a network. Can be accessed fine by all users.
I also share the folders with a Philips Media Player HMP/5000 which allows you to stream media via wifi from your network. I have had no issues with it streaming from the Mac up until yesterday when I upgraded to Maverick Operating. System. Now when I try to access the shared folders the Philips Media Device wants a Network Login and Password which it never wanted before. I changed none of my file sharing permissions and everything is as it was. I don't understand why all of a sudden it wants a network login. I have tried my user name and password for my Mac but that doesn't work.
Nothing in the UserGuide for the Media Player talks about this. I contacted Philips and they said it is an issue with my computer not letting me access the files.
I am wondering if the upgrade to Maverick has somehow changed some sort of settings somewhere which no longer allows this device to access the shared folders?
My file Sharing is on and states that everyone has access. My firewall is turned off.
Anyhelp would be greatly appreciated.

Although not directly an answer to your question, I recommend you use a wifi router to allow all your devices to get onto the Internet. I never recommend using Internet Sharing with a computer. Sorry I could not directly answer your question.
That said, someone will be along to help you with Internet Sharing.

Wireless network not working

Hello,
I have a SMC7004VWBR Barricade Router, part # 7509821, version 2. I purchased the Router in 2004 and it has worked flawlessly since then up until last week. I have a home office network that consists of 2 desktop computers connected to the router via Ethernet cables and a laptop computer (Macintosh iBook, OS 10.3.9) connected via wireless (Airport card in laptop). My Internet connection is via DSL modem.
Beginning last week the iBook's wireless connection to the network stopped functioning on a consistent basis. When I wake the iBook from sleep there is no signal coming from the network even through airport is on and airport is selected in the system preference pane. I have played with all the settings and still no connection. However, after leaving the iBook off over the weekend while I was away, when I re-booted, the signal came back! But then it disappeared again after putting the iBook to sleep and then re-booting. This happened again after the iBook was off overnight and I re-booted. Now I cannot get the signal to appear at all, even if I turn off the iBook for a few hours.
In all other respects the network works fine. If I connect an Ethernet cable to the iBook from the router, the connection comes back on via ethernet, but airport stays disconnected.
I brought the iBook to a public library yesterday that has a wireless network and it immediately found the network and stayed connected. Does this mean the issue is in the router?
I would very much appreciate any help you can offer.
thank you,
Bob W.

Firstly what OS are you currently on? Guess you have check things like the deivce driver is installed, the device is in switched the on position (you did say yes to that) and not disabled in the network connections either... If you have done them, something else you can check is that the WLAN AutoConfig service is enabled and started. To do this open services, this can be done by the run command (Win Key + R) and type "Services.msc". Press ok. Near the bottom of the list that appears should be WLAN AutoConfig, check the service is started and its set to Automatic. If this helps yipee if not no idea what else it could be.

Login-signon script is not working....what could be the reason

I am attaching the relvant portion of the script which is not working. login.php calls this script logincheck.php
I have created a table and passed values into the table (in oracle). However echo shows no values being passed.
<?
$v1 = $_REQUEST[user_id];
$v2 = $_REQUEST[auth_id];
//$v3 = $_REQUEST[brcd];
// Checking in ORACLE database USerID, Passwd & Branch Code Combination
include 'ConnDB8i.Php';
//echo 'Passed values'.$v1.$v2.$v3;
if(!$dbconnect)
     echo "<br><br><br><br><table width=300 align=center border=1><td >Database is Not available...!<br>Try after sometime.</td></table>";
     echo "<input type='hidden' name='conn' value='NO'>";
return;
// Connecting to ORACLE 8i
$mSql = "Select user_name,auth_id,branch_cd,user_lock,user_type from scfu_users where user_id='".$v1."'";
echo "<br>'paased values'.$mSql";
$stmt = OCIParse($dbconnect,$mSql);
OCIExecute($stmt);
$nRows = OCIFetchStatement($stmt,$result);
echo "<br>'passed values'.$nRows";
if($nRows==0)
     echo "<Br><font size=5>Invalid User Id</font>";
     OCIFreeStatement($stmt);
     OCILogoff($dbconnect);
     return;
reset($result);
$colcnt = 0;
$i=0;
$nRows reurns 0...... why?
$mSql is correct. It returns values as expected.
The error I am getting is invalid User ID.Obviously $nRows is 0 when it should not be so.
Any suggestions/answers please??
JJZ

A couple of things I noticed:
Add error handling and check the return value from the OCIExecute() call.
Use bind variables in the WHERE clause to avoid SQL injection issues.
Use the most recent version of PHP and the oci8 extension that is
compatibile with your version of Oracle. (Or get the free version of
the Oracle DB from http://www.oracle.com/technology/products/database/xe/index.html )
-- cj

IMessage from iPhone 5 not working to iPad 2 internationally

Hi there,
I am hoping someone can help me with clarifying why iMessage from my wife (iPhone 5, iOS 6.1.3, currently in South Africa) is not working to me (iPad2, iOs 6.1.3) at the moment. She is unable to send to me, but experiences no problems in sending to our kids in Canada (who are all on iPhones). When she is in Canada, iMessage works just fine. Is it because iMessage is transmitting to my kids' iphones via cellular, but she is unable to txt me (my iMessage is linked to an email address) because she is not on a data connection/WiFi? Is iPod appreciate any assistance; thank you!

Thank you very much for your help MetaSolaray; this is most helpful ... I have followed your advice and was able to establish the following:
My kids can send messages to my iPad via iMessage, and they receive messages sent from my iPad ... so, all ok with respect to Apple devices in Canada!
It now has become apparent that messages sent by my wife from South Africa to my kids' iPhones are received randomly (i.e. not consistently), and still not delivering at all to my iPad. What is interesting is that my wife is able to txt my eldest's Blackberry perfectly. Does this mean that it is an iMessage/iDevice to iDevice issue?
My wife has not yet been able to get to a WiFi location, so all texts have been sent via cellular (data roaming is turned off on her iPhone). We are hoping that soon she will be able to get to a location where she can hop onto a wireless network to test this further; but, I have to say, I find this highly frustrating as txt (pre-iMessage) seemed so reliable. I will keep you posted ...
I really appreciate your kind assistance!

Extending wireless network, not working?

ive been trying to set up a new wireless network for a few days now and while i got this network up and running i still doubt if its exactly what i want.
i have extreme(n), time capsule(n) and an express(n). im using the extreme as my "base" which is connected to the internet and both the capsule and express are connected by wires. but whenever i use the setting "extend a wireless network", the stations will just become undetectable and not working at all. so to get my network to work i configured them all with "create a wireless network" giving them all the same network name which is working fine. but is this even roaming?

Welcome to the discussions!
When you are having extending difficulties, it's often helpful to temporarily locate the Express near your main router...across the room or in an adjacent room and test to see if that works.
If things worked fine for 6 months and suddenly you have problems, that may indicate that a new wireless network near you has been added at one of your neighbors, which is causing interference on your network.
Cordless phones are a real problem as well. My neighbor...across the street....can literally knock me off my network if he is in his front hard talking on his cordless phone. I found this out simply by accident, otherwise I would still be blaming Apple for stuff that worked fine for months and then suddenly did not work.
If the Express works close to the main router, then move the Express further away and test again. Most users locate the Express too far away from the main router when they try to extend a wireless network. A good starting location is a point that is about 1/2 to 2/3 of the distance between the main router and the area that needs more coverage.
Open AirPort Utility and click on your AirPort Express on the left and look for its AirPort ID on the right. Jot that down.
When you are testing the extension of the Express, move your laptop close the Express, and hold down the option key on your Mac while you click on the fan shaped AirPort icon at the top of the screen. Look for the BSSID. This should match the AirPort ID of the Express, indicating that your computer is connecting to the AirPort Express.

Jabber login from public network not working

Similar Messages

Maybe you are looking for