Jabber on all phone ports

All of my 3560 ports connected to phones (7940/42/60/70/71) are showing continuous 50pps output towards the phones. I've turned off GARP but still no improvement.
Although most of these phones have PC's attached, the data VLAN is not affected.
I can't get an ethereal until tomorrow but on the off chance anyone has seen this before ?
Here's a sh int from an affected interface :-
FastEthernet0/7 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 001d.e516.6109 (bia 001d.e516.6109)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is 10/100BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:50, output 00:00:00, output hang never
Last clearing of "show interface" counters 00:00:01
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 90000 bits/sec, 51 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
104 packets output, 22640 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
Appreciate any ideas.
TIA.

Hi,
I had the similar problem like you now.
The problem was in Microsoft Load Balansing.
The Microsoft guys have tried to do load balansing but it didn't work and there was a lot of multicat packets in that VLAN.
After we have removed these servers, everything was OK.
Maybe this can help you?
Regards,
Vlaho

Similar Messages

  • I have a new iMac and want to use my HP 7300 All in One and to use the "Fax"feature I need a phone port on computer and of course, this computer does not have one.  Are there any aftermarket devices for USB to phone that would work in this case?

    I have a new iMac and want to use my HP 7300 "All in One and cannot use the fax feature because there is no phone port is there a solution for this?BACellli

    You don't need a phone port on the iMac. The HP 7300 DeskJet Pro has an internal modem, you connect the printer's modem connection directly to your phone line. Please re-read the install directions that came with the printer.

  • Jabber and Desk Phone Integration

    When stting up "Desk Phone Integration" on cisco Jabber on a test iPhone, Jabber loops forever when verifying account information saying just "verifying...". It never display an error message. It will eventually stop, the "Desk Phone Integration" staying "Not Configured"
    CUCM version : 8.6(2)
    iPhone iOS : 6.0.1
    Jabber client : 9.0.2.20078
    I followed the instructions in the "Administration Guide for Cisco Jabber for iPhone Release 9.0.1" to setup the call manager.
    I created a dedicated SIP profile,
    created the TCTTEST "Cisco Dual Mode for iPhone" phone according to the documentation
    and edit my phone and user settings according to the "Enable Active Call Transfer Between Cisco Jabber and Desk Phone" section of the documentation
    despite all that, it doesn't work
    I tried with other accounts/mobiles and the result is the same.
    Jabber does register to the CUCM and I can get my extension on the Jabber client and place/receive calls using my desk extension. But the "desk phone integration" doesn't work
    What I noticed is that :
    on the TCTXXXX "Cisco Dual Mode for iPhone" phone device setting page, there is no "Sign In Feature" option as described in the documentation
    because we use Extension mobility the "Owner User ID" feature is disable on the desk phone device settings. I temporarily uncecked the "extension mobility" checkbox on the device, setup my ID as the "Owner User ID" and re-checked the "extension mobility" checkbox but the result is the same.
    I searched the web and couldn't find anyone with similar issue...help will be appreciated

    Aaron,
    Thanks for you answer.
    I have followed all the requirements explained in the "Administration Guide for Cisco Jabber for iPhone Release 9.0.1" including the one you mentioned :
    the user is a member of  'Standard CTI Enabled'
    CTI Controlled is allowed on the DN, the end user account and the desk phone
    the end user is associated to both the desk phone and the TCT phone
    And 'Allow End User Configuration Editing' is set to disable on the TCTxxxx device
    Despite all that the "desk phone integration" doesn't work

  • Jabber for Window, phone mode, how to disable "use my computer for calls"

    We have a Citrix environment and only want to control the Cisco deskphone with Jabber for Windows in the phone mode.
    We use CUCM 8.6.2 and I have installed Jabber for Windows 9.7.0 and all works fine, I can control my deskphone, make and receive calls, phonebook and Outlook integration works fine.
    Is it possible to disable "use my computer for calls" as we do not want users to make calls via Citrix, but only use the deskphone for this.
    Thanks, Perry

    Hi Matthias,
    Soft-phone mode cannot be disabled. Supported Features on Virtual Environment are the following.
    Supported Features
        Instant messaging and presence with other Cisco Jabber clients
        Desk phone control
        Voicemail
        Presence integration with Microsoft Outlook 2007, 2010 and 2013
    We have an existing defect which is in Terminated state because feature is not supported hence cannot be fixed.
    CSCub40605 - J4W - Ability to disable softphone mode in Citrix environment.
    HTH,
    Please rate if you find this post helpful.
    Regards,
    Mohammed Noor

  • HT4060 Cannot get iPad 2 charged beyond 1%.  All charging ports tried: AC adapter(s), USB 2 port on MacBook Pro. ITunes shows iPad only for a few seconds. iPad displays alternately: Apple logo, battery w/slim red band, then battery w/1% charged informatio

    Cannot get iPad 2 charged beyond 1%.  All charging ports tried: AC adapter(s), USB 2 port on MacBook Pro. ITunes shows iPad only for a few seconds. iPad displays alternately: Apple logo, battery w/slim red band, then battery w/1% charged information. How can I get it to charge beyond 1% so I can proceed to troubleshoot?

    I have had your exact problem with my old 3GS, now I cannot even get it to turn on, I still see that it is supposed to be charging though, but it never charges any so it seems.
    I replaced the Lower Dock Connector Assembly back when it still charged while hooked to my PC, and it found it made no real difference.
    http://www.amazon.com/gp/product/B003Y5YXLK/ref=oh_details_o05_s00_i00?ie=UTF8&p sc=1 
    At this point I am not sure if I should replace the battery and hope for the best, or just junk the phone, I cannot really sell it if I cannot reset it...

  • Itunes Freezes during Sync on 3G & 3GS with Vista 64 & 7-64 all USB ports

    To start. I originally had an iPhone 3G over a year ago on this desktop running Windows Vista 64Bit. My phone was able to sync with the PC for about a month and stopped being able to sync. I received many error numbers and put support tickets in with no avail. I then upgraded to an iPhone 3GS. Still under Windows Vista 64Bit and could not Sync my phone. It consistantly froze during the sync process. I tried all USB ports on my PC. People said to try restoring your iPhone and iTunes. I tried that and then got stuck on my restore. I had a broken phone until I was able to sync with my laptop.
    I now have the same desktop Acer AM3641-EQ8200A but I am running Windows 7 Ultimate 64bit. I have always had the latest iTunes version, and tried 32 bit and 64 bit versions of iTunes. I still cannot successfully sync my iPhone. If it sits there long enough it will freeze up, start to freeze my computer etc. I decided to try again last night after I got a new USB cord and had the same issue.
    In addition, my girlfriends iPod will not sync to the desktop either.
    I have been stuck doing syncs on my Netbook for over a year now. Optimization of 3,000+ photos is horrific on it, but it works.
    People say to get an external USB that is self powered. Why should I have to do this and chance frying my PC?
    The deal is this, the phones won't sync with the desktop but will sync with my netbook also running windows 7 ultimate. All USB drivers are up to date on both.
    I have tried Reformatting and Installing Windows. Reinstalling itunes. Updating all drivers. Tried different versions of iTunes. I first called Apple Retail, they had no answer. I wrote apple a lengthy letter with all the Error codes, they said they would call me even though my warranty over the phone support was expired. Never got a call back after they heard my problem.
    What can I do to rectify this? I am not the only one out there.

    UPDATE:
    After putting a USB 2 card in my mac, all worked properly. The problem seems to be using USB 1.1.
    This is really tragic because:
    + many Macs don't have USB 2,
    + it is very difficult to find out out if USB 2 exists on your computer (why are no USB 1 or 2 details spelled out in system profiler ?),
    + there are no warnings as to the sort of issues that would be coming up with USB 1.1 (yes I know the specs clearly says USB 2, but it looks like it was working at first),
    + there are no spelled warning by the system (after all, the iTune, iPod combination could detect easily that the incorrect USB standard is being used and warn the user),
    + there does not seem to be specific advantages to use USB 2 (like speed) as the syncing peaked at 6MB/s, a speed achievable with USB 1.1
    Come on Apple you can do better than this !

  • In CCM, Associate User with All Phones

    This is 1 of 2 threads I am starting.
    1. (this thread) asks for guidance in associating a User with all IP Phones in order for them to obtain authentication before allowing XML to be pushed to them.
    2. (in a separate thread) asks for guidance in issuing the push to the IP Phone, regarding getting the base64 User:Password inserted into the HTTP pkt.
    Thread 1:
    I want to push a CiscoIPPhoneExecute to IP Phones. I am having trouble authenticating. I know that in order to authenticate (UserID,Password) I must add a User (with User ID and Password) to CCM and associate it with all IP Phones. My CCM ver is System version: 5.1.1.2000-2.

    How do you want to do that? Manually or do you want to write a software that does it automatically?
    To do it automatically you need AXL. First you need to look up which devices your application user is already associated with.. you run the following query (taken directly from productive java code):
    private String getDeviceAssociationSqlString(String ctiUser)
    StringBuilder sb = new StringBuilder();
    sb.append("SELECT dev.name FROM device dev INNER JOIN applicationuserdevicemap adm ON adm.fkdevice = dev.pkid AND tkuserassociation = 1 ");
    sb.append("INNER JOIN applicationuser a ON a.pkid = adm.fkapplicationuser AND a.name='" + ctiUser + "'");
    return sb.toString();
    You do an executeSqlQuery with that query and parse the results (the response will look something like
    SEP123SEP124/row>..
    Then you look up all devices, e.g. by sending a query like
    SELECT name FROM device WHERE name LIKE 'SEP%'
    (the where clause is to only include IP phones..the device table also contains gateways, analog ports, etc. and we don't want that.. not that this query includes third party sip phones which doesn't make too much sense.. but it won't cause any problems either.. I know because we run that code on a system with third party sip phones).
    Then you do a delta between the two lists and if the second query yielded more results than the first, you need to associate the application user with that phone. There's no direct way in AXL (there used to be in CCM4 but no longer in CCM5+ because we now use application users.. you could theoretically use end users where you can still use updateUser, however it's not a good idea to mix application and regular users).
    So.. you need to update the SQL database directly.. and run executeSqlUpdate via axl. The query to add phone deviceName to application user ctiUser is:
    private String getAddDeviceAssociationSqlString(String deviceName)
    StringBuilder sb = new StringBuilder();
    sb.append("INSERT INTO applicationuserdevicemap (fkapplicationuser, fkdevice, tkuserassociation) VALUES((SELECT pkid from applicationuser WHERE name = '");
    sb.append(config.ctiUser);
    sb.append("'), (SELECT pkid FROM device WHERE name = '");
    sb.append(deviceName);
    sb.append("'), 1)");
    return sb.toString();
    This also works on CCM6, and most likely on CCM7 (I haven't had any projects with 7 yet but at first glance I haven't spotted any major changes like in between CCM5 and CCM6 (the extension mobility stuff has completely changed between those releases).
    And if you do it manually.. just go to your application user, and have have the device association right there.. press the select more phones button, search for all phones whose name starts with sep, check them all, and submit.

  • Using both phone ports on linksys rt31p2

    i have configured both my phone ports to two different service providers on my linksys rt31p2 box.individually both the ports work fine if i get call on either one line at one time,but if i get call on both the lines at the same time,one line becomes totally dead- meaning no voice on either side and one line functions fine.
    if i get call on line 1 and while i am talking i get a ring on line 2, the line 2 will have no voice but i can continue talking on line1 without any problem
    pls help what to do?
    the QOS for voice upstream is enabled and set to 512 kbps
    Message Edited by cheetahzee on 04-16-2009 04:21 PM

    My 2 phoneline LED's are not on. When inputtting the following VOIP settings:
    Proxyserver: sip.voibuster.com
    stun server: stun.voibuster.com
    Display and userid: the same as registration
    They use port: 5060
    I have put also port 5060 in the application and gaming settings.
    I have tried actually multiple settings and read through all the setup guides and after 5+ hours I thought to ask on this forum for some advise. Hope you have some?! look forward to hear from you.
    Message Edited by jackmin on 05-25-2009 11:11 AM

  • I have three iPhones using the same iTunes account, can we set something so that we are not all getting everyones txt messages to all phones?

    I have three iPhones using the same iTunes account, can we set something so that all our txt messages are not appearing on all phones?

    Settings > Messages > Receive At...
    Any iPhone that lists the same email will receive the same texts. This has to be changed in order to stop receiving on all devices.

  • How to find all JMX ports on a server?

    How to find all jmx ports on particular server (say localhost) on windows
    I have multiple JVM's running on my local server, and there is extensive use of JXM mbeans by the applications running on each server. So I want to connect to all these JMX servers and to instrument the MBeans using Jconsole(Jconsole localhost:<port>). But I don't know the port numbers, and its not logged by the application.
    How do I find all the ports jmx servers connected?
    Note : In my case I can not instrument using the PID.
    thanks,
    bala K

    Hi kajbj,
    I tried stop/start the application, but couldn't find any difference in the netstat command. I know it should show the JMX port (I am able to see on a test application), but this application's JMX port usage is missing.
    netstat -ano --> Do i need to use any other commands?
    I just injected few lines of code ( to list the MBeanServers programatically), to this application (did some usual tweaks to let this code execute at some time) and its listing couple of MBeanServers and lot of MBeans.
    MBeanServerFactory.findMBeanServer(null); and so on.....
    Is there a way to get the port using the Management API's?
    thanks,
    bala K

  • All USB ports are no longer 2.0

    I have been struggling recently with the USB ports on my Intel Mac Mini, circa 2007, OSX 10.5.8. Everything I plug into any of the 4 USB ports in the back will come up as a 12 Mbps port, not a high speed 2.0 port. I don't know how to diagnose the issue here. Seems like they use to work but at some mysterious point I noticed issues.
    HW View shows 4 USB Buses, corresponding to all 4 ports. Anything I plug in shows up as 12Mbps. There is a mysterious 5th USB bus labelled 'USB High Speed Bus', but nothing seems to attach to it... I figured all the ports were high speed???
    Confused... any idea what to do to get these ports back into '2.0' mode?
    Derek

    Frequently multiple ports share the same bus.
    If you plug in one slow device into any port, all the other ports that share that same bus will be that slow. The only way around it, is to use a high speed hub with known high speed devices hooked up to the hub and that hub connected to your Mac. Then you can discover which of the ports is definitely on the high speed bus. Once you've done that, only connect low speed devices to known low speed ports.

  • I just upgraded my iPhone4 iOs and lost ALL Phone Contacts! How can I get them back?

    HELP! I've been using my iPhone consistently for ALL phone numbers, since I have serious memory problems due to fibromyalgia. I upgraded my phone last night finally, having moved my photos out of it I had the space to download and install the upgrade.
    I got a nasty shock this morning when I tried to make a routine call and found ALL of my phone contacts missing. They don't seem to be either in the cloud or in the phone. What happened? It said it was storing them in the cloud but they're all gone! How can I get them back?
    IF this normally happens, why should I ever upgrade? Seriously! I didn't think to copy all of it out manually before upgrading, I'd upgraded once before without any problems. Addresses and other details gone too. I've got four numbers in "Favorites" but no context for them beyond location by state. I don't even know who they are - can't recognize just the numbers.

    Thanks, but I checked iCloud and it has none of them.
    If it backed up to my laptop, that died and I just got the new computer. The one that's crashed won't even boot, so there's no way to even tell if it was syncing the contacts along with all the phone photos. Literally happened at the same time - it was because I had the new computer that I was finally able to pull the photos off the phone and make room for the upgrade. It had refused to upgrade for lack of space for some time.
    I had thought it was set to sync to iCloud but it vanished from BOTH my phone and the cloud. That's why I'm so angry about it.

  • TS4268 I am able to imessage from my ipad all phone numbers in contacts but one. With it a get an error message that say "number is not registered with imessage". However I am able to imessage that number from my iphone. Any suggestions?

    I am able to imessage from my ipad all phone numbers in contacts but one. With it I get an error message that says "number is not registered with imessage". However, I am able to imessage that number from my iphone. Any suggestion?

    Hey joshuafromisr,
    If you resintall iTunes, it should fix the issue. The following document will go over how to remove iTunes fully and then reinstall. Depending on what version of Windows you're running you'll either follow the directions here:
    Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
    http://support.apple.com/kb/HT1925
    or here:
    Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
    http://support.apple.com/kb/HT1923
    Best,
    David

  • TS1702 i have erased my all phone contact list and then the message comes that it will be deleted with in an hour. but now my phone is not starting and only the apple logo appears on the screen. what should i do now..!

    i have erased my all phone contact list and then the message comes that it will be deleted with in an hour. but now my phone is not starting and only the apple logo appears on the screen. what should i do now..!

    That number is for an apple server in the UK that is used for iMessage activation.  A hidden SMS is snet to that number when you turn iMessage on and is used to verify your phone number.  I suggest you turn iMessage off.  In settings/phone turn on dial assist.  Check with your carrier to see if you can send an international SMS as you end that possibility to activate iMessage.  Rest your phone (Hold down the Sleep/Wake button and the home button together until the apple logo appears (ignore the ON/OFF slider) then let both buttons go and wait for device to restart (no data will be lost).) then turn iMessage back on.

  • Is moving all active ports to another VSAN disruptive?..

    Hi! I moved all active ports to another VSAN and this caused a server to failure. I know that this can be because of the small time-out values at the operating system or bad multipathing, but how large a time-out can be in a such reconfiguration?.. What if the server can't survive any storage loss and we move server and storage array ports to another VSAN? I wonder if it can be done without any traffic interruption...

    Hi Artem,
    Changing server from VSAN is a disruptive process for each path you're acting on: that means if you're not having dual fabrics and proper multipathing configuration, the server will lose access to its LUN for a certain amount of time. Depending on the operating system you might expect various behaviors (kernel panic, SCSI errors, CPU in I/O wait until timeouts,...). Consider it even more restrictive when booting on SAN or when swap memory is also on a SAN LUN.
    It's always good practice to work one one fabric at a time by disabling the path attached to it from the OS perspective (if multipath software is not set in a failover mode).
    Changing VSAN membership for a FC port on the MDS9000 means that the initiator HBA has to log (FLOGI) into a new VSAN where the DomainID is different from previous VSAN, so its FCID will change also. It is same effect as moving fibers to another physical SAN from the host perspective.

Maybe you are looking for