Jabber voice mail failover

Dear,
I have publisher and subscriber for unity connection 9.1, whenever the UN PUB fails voice mail doesnt work in jabber for windows for subscriber,
i telnet to  port    telnet <unity connection> 143 and i m able to telnet on IMAP and also on port 443 of voicemail server.
Any hints please.

this is an enhancement documented here; https://tools.cisco.com/bugsearch/bug/CSCud63427/?reffering_site=dumpcr
please rate if this helps.

Similar Messages

  • Jabber voice mail for some users.

    Dears,
    J4W voicemail works perfect with default config.xml file for some of the users and for some of the users it shows the attached when clicked on voicemail tab. I have create 2 no's of sevice profile, the voice mail credential set  for both service profile is Unified CM IM and presence.
    I can understand the prompt as it is asking for voicemail password for that reason i have to create a custom config.xml file and i have to upload in TFTP server, But my concern is why it is working for some of the users without config.xml file and for some users it is prompting for username and password.
    Thanks

    Dears,
    the profile are different, but if i put the the other users working profile also it is not working.
    The voice mail server is showing not connected in jabber,
    Any hints.
    Thanks

  • Jabber call to voice mail fails with fast busy over VPN

    I have an issue that I ran into with CIPC phones over a VPN.  If a CIPC phone called over a VPN and started ringing a phone the call would fail with fast busy at the time the call would be forwarded to voicemail.  I found the issue was when remote the CIPC phone would negotiate the g.729 codec, when forwarded to a voicemail pilot over a SIP trunk set to g.711 the call would fail due to codec missmatch when no transcoders are present.
    So now I am running into what I believe to be the same issue with Jabber, when on premise the calls to voice mail work just fine, but when remote they fail.  I can directly call the voicemail pilot without error, but if calling a phone the call gets fast busy at the point we are forwarded to voicemail.  Even though all my regions are set to talk to all other regions on G.711 and the voicemail SIP trunk is set to G.711, I believe with the new features in CUCM9 that a lower speed codec has been negotiated since the we are going over the VPN, or Jabber has done this as it knows it's over VPN (not sure).  WIth CIPC I could go into the settings and turn off the Optimize for Bandwidth check box and the call would negotiate G.711.  With Jabber I can't find anything that would tell my Jabber client to stay on G.711 and I can only imagine this is a codec missmatch as the following are true.
    1. CIPC and Jabber share the same line
    2. VPN established and CIPC optimised for low bandwidth un-checked
    3. Over the same VPN the CIPC phone can leave a voicemail
    4. Over the same VPN the Jabber client gets fast busy once forwarded to voicemail
    5. Voicemail environment is Exchange-UM over SIP trunk
    6. SIP trunk is assigned a Device Pool, that is assigned to a region that all other regions communicate G.711 to
    7. On CIPC if optimised for low bandwidth is checked I get the exact same issue as I get with the Jabber client (fast busy when forwarded to voicemail)
    Would anyone know what I can do in CUCM 9 to fix this issue, as said no issue when all devices are on premise.  Wondering if there is a service parameter or a way to change the codec selection so the Jabber client attempts to always negotiate G.711.  The correct answer would be to get some PVDM DSP resources and kick up a transcoder in my resource group, and that may be what I talk them into doing if I have no other options.                  

    We have been getting the exact same thing for almost a year now... since switching to FiOS Digital Voice in May of last year!  Every time I call in to report it they 'escalate' the issue but it never gets resolved.  The problem seems to be in the initial connection.  Most of the time it works fine but, several times a month, after I call to get messages and it starts to play the new message it goes dead and I get the busy signal.  I get the same message when I call back:  “I’m sorry – that account is in use at this time.  Please try again later!”  I have even called in with my cell phone and get the same message!  I HAVE EVEN used the Internet to see if I could get my messages and, when I hit Play, I get a pop-up saying: “Your Voice Mail box is currently in being accessed; please try again later.  If the problem continues, please contact our Customer Support Center at 1-888-553-1555. We apologize for any inconvenience.”  This is obviously a software bug that Verizon has no clue on how to troubleshoot OR fix!!!  I wonder how many people have the problem and just don’t bother reporting it because of the hassle?  When it first started happening they destroyed my entire mailbox and I had to re-enter the complete mailbox setup again – 3 times!!!  NEVER let them talk you into that!!!  It’s their problem and they need to fix it!!!!!!!  I wish I could go back to the ‘normal’ voicemail we originally had… they want hundred$ to switch back because I’d be breaking my #$@%^&* contract!  Good luck if you have Verizon………

  • Jabber for Windows client Voice Mail issue

    hi, cisco guys
        i have a collaboration test for my customer in resent days.
        the follow picture is the topo of my test system
       1.  cucm1 use ICT non-GK trunk to connected with cucm2 and the ip phones with dn 56xx registered on cm1
        the iphones and jabber clients with dn 54xx registered on cm2
       2. cm2 intergrated with Unity Connection server and  Cups server
           the version of cm1 and cm2 and unity connection is 8.6.2-21900
          the version of cups is 8.6.4
      3.  the issue occurrenced when the ip phone user 5412 call to 5411 but no answered, user 5412 sent a
          voice mail to user 5411，only MVI of the ip phone 9951 with dn 5411 turned on but jabber client wihtout any prompt message
          but when the user 5665 which  registered on cm1 called user 5411 and sent a voice mail , status in normal,
          mvi turned on , the jabber client also can  recived the prompt message and the the vocie mail could be played on the jabber client
          what's the issue  probably be caused by & how can i solve it
          need your help!!!!

    I don't know if you have a specific subnets permitted in the CUPS ACL
    This is dangerous and incorrect guidence. The Incoming ACL allows the addresses defined to bypass authentication. In other words, I could impersonate your CEO if I wanted to. There are only two common use cases where doing this is appropriate: 1) the CUxAC server IP; or 2) older versions of CCX where CAD didn't support DIGEST authentication.
    As for the original question: your English is difficult to understand. Is the following problem statement accurate?
    When 5412 on CM2 leaves a voicemail for 5411 on CM2, the MWI is lit for 5411 but Jabber does not reflect the waiting message?
    If this is accurate, is the message also shown in the Web Inbox? https:///inbox
    The serverIP should be the CUC server defined in the voicemail profile on CUPS for the user who owns 5411.
    Please remember to rate helpful responses and identify helpful or correct answers.

  • Jabber can not enter the PIN for voice mail

    I installed Cisco Jabber 8.6 on the android mobile,And registered jabber to CUCM8.0. In the same time, CUCM8.0 integrated with Unity Connection8.0 via SCCP, Everything is normal.
    Tested using any of a telephone call Jabber, it can received voice mail, and shows have a voice mail on the android mobile. then, Hear the tone of the Connection system :"please enter your PIN." However, in any case the PIN can not be submit to the Unity Connection, System reminded over and over again:please enter your PIN.......
    I guess the mobile's dial pad can not be supported by Unity Connection, Or other reasons.
    help!!!

    The Android client is a SIP device and uses RFC2833 for DTMF relay. Unity Connection supports RFC2833 when integrated with either SCCP or SIP. The first question that comes to mind: is the call invoking a transocder/MTP that would be in the media path? For example, if Jabber is using G.729 and you haven't enabled that on CXN or you're requiring a TRP.
    I would start with a Wireshark capture from the CXN server to see: a) what the far-end IP address is for the RTP packets; and, b) whether you see the RFC2833 packets arrive. If the sender IP isn't the Jabber client a media resource got invoked which may be dropping the RFC2833 packets. If the IP is correct but you don't see the RFC2833 packets arrive you could then run a Wireshark or collect SDI logs with SIP stack trace enabled from the CUCM node that Jabber is registered to. That would allow you to see the SDP negotiation at call setup to see if RFC2833 even gets negotiated.
    Please remember to rate helpful responses and identify helpful or correct answers.

  • Jabber for windows can't play voice mail

    hello everyone....
    i config jabber with Unity Connection
    now i can receive a voice mail form jabber ,all is right ..but i can't play it
    if i login the voice mail i can hear the voice mail......only can't play form jabber ...
    my jabber client is 9.2 and CUCM 9.1 Unity Connection 8.62 CUPS 9.1

    We have the same problem with Jabber for Windows 9.2.
    It is interesting that the voicemail feature seems to work for a few seconds when the client starts up. At this time I can see all of voice mails, and the number of unread voicemails shows as a number where the voicemail icon is, but then they all disappear. The voicemail tab then shows the message, "Cisco Jabber is not connected to your voicemail server".
    The 'Call voicemail' button works.
    I understand that our server has been setup for TLS, and that the voicemail tab in Jabber for Windows 9.1.5 works.

  • Why my iphone 5s voice mail answer call first and my iphone second.

    why my iphone 5s voice mail answer call first and my iphone second.

    Hello celazopdef,
    After reviewing your post, I have located an article that can help in this situation. It contains a number of troubleshooting steps and helpful advice concerning cellular issues:
    iPhone: Troubleshooting issues making or receiving calls
    http://support.apple.com/kb/TS3406
    Thank you for contributing to Apple Support Communities.
    Cheers,
    BobbyD

  • I Have No Voice Mail Notifications In Z10 Hub

    I have seen issues with Voice Mail Notifications in various threads, but I didn't see one having No Voice Mail Notifications In the Z10 Hub at all. Sorry if I missed a thread that applies.
    From what I was told by Blackberry Technical Support, at the bottom of the BB Hub next to "Calls", "Emergency Alerts" and "PIN", should be "Voice Mail" (or something similar). I have none and therefore do not get any notifications when I receive a Voice Message. I thought this was odd, and figured I had some settings incorrect, but that is not the case. It's just not there.
    I am in the USA on Verizon's network with the latest updated OS 10.1.0.2039 that they offered on a STL100-4, Z10.
    Anyone else have this issue?

    My wife had the same issue on her Z10.
    A quick call to customer service at AT&T and they set it up.
    Rebooted her phone, and all was well.
    I'm sure Verizon customer service can do this for you as well.
    Hope this helps.
    Sincerely -

  • My iphone 4s sometimes wont show voice mail,sometimes wont ring just shows missed call,sometimes wont receive a text till next day. can anybody help me???

    My phone sometimes wont show voice mail,sometimes wont ring just shows missed calls,and some text messages wont show received till next day. Can anyone help?

    Settings > General > Reset > Reset Network Settings.
    Try reseating or replacing the SIM card.
    Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new). 
    Has any of the above been tried?

  • Jabber voice crashes on iPhone 5S

    Hi,
    Just installed latest version if Jabber Voice from the Apple AppStore and it immediately crashes when selected. I am running IOS 7.0.4.
    Anyone experiencing the same thing?
    Appreciate all assistance!

    The following error is reported via Console:
    iPhone ReportCrash[4722] <Notice>: Saved crashreport to /var/mobile/Library/Logs/CrashReporter/Jabber Voice_2014-05-19-083318_"removedname".plist using uid: 0 gid: 0, synthetic_euid: 501 egid: 0
    May 19 08:33:19 iPhone Jabber Voice[4724] <Warning>: Stderr redirected to: /var/mobile/Applications/0CDDD8A3-0BD0-40DA-AFCA-8B32C71B0187/Documents/Logs/Jabber Voice-2014-05-19-08331907-Console.log
    May 19 08:33:19 iPhone Jabber Voice[4724] <Notice>: (Error) [ABLog]: ABPeoplePickerNavigationController does not support subclassing in iOS 7.0 and later. In the future, a nil instance will be returned.
    Issue happens on iPhone 5S running 7.0.6 or 7.1.1 iOS. 

  • How do I delete voice mail from my iphone 4s?  I am getting a message that my voicemail is 98% full.

    How do I delete voice mail from my iphone 4s? I keep getting a message that my voicemail is 98% full.

    i realised i have this 200mb of messages this morning & tried deleting my messages but it started to hang half way and my phone gets very hot. thn i do pressed my lock & home button to reset the phone, thn it cool atfer awhile but i got all my messges back lol..
    thn i found out, after deleting all the unwanted messages, sync to itunes, thn all the messages is gone for good. hope it helps?

  • How to stop voice mail password pop up on iphone 5

    How do you stop the voice mail password pop up on the i phone 5?

    Call your carrier & have them reset your voicemail. Then set such up with a password. Voicemail is a carrier feature, not a phone feature & most carriers require a password for such.

  • I can't set up voice mail on my iphone 5s. And can't merge calls either

    I can't set up voice mail box on my iphone 5s .
    And I can't merge calls .

    Both of those functions are carrier dependent so you may want to contact your cellular carrier.

  • Voice mail password problem, iPhone 5S

    I have a 5S, use AT&T for voice mail. Every time I finish listening to a voice mail, I get a pop up asking for my password. I enter the password, but after listening to the next voice mail, I get the pop up again. Happens EVERY time. The popup does not affect my receiving or listening to voice mails. I've tried hitting cancel to the popup request, but it continues to appear--and I continue to receive my voice mail. Its very annoying. How do I get rid of the constant popup?

    KLSQUESTION wrote:
    How do I discover the password for the voice mail?
    Voice Mail is a Carrier controlled feature. Contact your Carrier.

  • IPhone 5s doesn't ring and goes directly to voice mail. Do not disturb is disabled. Have reset network settings and did a hard reset.  What am I missing?

    iPhone 5s doesn't ring and goes directly to voice mail. Do not disturb is disabled. Have reset network settings and did a hard reset.  What am I missing?

    Call your phone carrier - that's a problem for them to resolve.

Maybe you are looking for