Jabra GN9120 headset and Cisco 7970G

I purchased a GN9120 wireless headset and tried to install it on my Cisco 7970G IP phone. But when I use it, the far end user always hears echoing.
Does anyone have the experience of using GN9120?
What is the proper setting for GN9120 to make it works with my Cisco phone?

Did you ever find a solution for this?

Similar Messages

Jabra headset and Cisco 7942 Aux port

Hi ,
Two of our employees are using Jabra headsets. They are currently working over the analog headset port, but they would like to use the digital converter cable the headset came with to improve performance. How should I turned it on to utilize the auxiliary port in behind the phone.
Head model: Jabra GN9300e
Phone model: 7942
Any help would be much appreciated.
Saima

Hi Saima,
With the Cisco 7942, you would leverage the setting under
the product specific porting of the config via device>phone
and set Wireless Headset Hookswitch Control to Enabled
http://headsetplus.com/PDF/Jabra-EHS-guide.pdf
Cheers!
Rob
"And if I should fall behind
Wait for me" - Springsteen

Cisco 7926 with Jabra Pro headset

Hi all!
We have a Cisco 7926 desk phone connected to a Jabra Pro wireless headset. It's connected with a headset cable from the phone to the base station and set up correctly according to the instructions from Jabra.
My problem is that when we use the headset it ends a call when transferring. Using the original tube it works fine and this only happens when using the headset.
The thing is that we just upgraded our CUCM software to system version 10.5.1.10000-7 and after that it stopped working.
What i have tried is checked if the phone are headset activated, and it is. I have reconfigured the Jabra Pro headset.
Any suggestions are accepted with great thanks :)

There is a bug with 79XX phones transferring using headsets. You need to check CSCun26289
https://supportforums.cisco.com/discussion/12166856/problems-transferringanswering-calls-when-using-headset-79xx-phone-cscun26289

Ipod touch bluetooth and jabra jx10 headset

I have been trying all evening to pair my ipod touch by bluetooth with my jabra jx10 headset. Searches forever but sees nothing.
Wondering if anyone knows whether these items are not compatible? My blackberry phone sees the jabra immediately.
Any suggestions will be very welcome.
Thanks,
Mike

Meg St._Clair wrote:
The Touch does not have the requisite BT profile for a headset (the kind with a mic that you would use with a cell phone). It will support stereo headphones, stereo speakers and, I believe, some keyboards. Sorry.
Hi there,
is this still fact with iOS 4.1? I'm just on the way to order a BT-Headset with mic for my son's 2G touch and Mac mini (gaming and Skype).
Regards
Jochen

IPad and Jabra HALO headset

Anyone ben able to get it to work with an iPad??? I have only been able to get the audio to work, but can not adjust the volume using the headset controls, and non of the other headset control functions work.
THX!

Technically, the problem isn't that the Jabra JX10 supports headset and hands-free - the problem is that it doesn't support A2DP, which the iPad requires. Bluetooth headsets can support all three of those profiles, and that's fine - as long as the headset supports A2DP along with whatever else it has, it'll work on the iPad.
Just another note: most mono (monaural) headsets don't support A2DP, though there are a very few. Many, but not all, stereo bluetooth headsets do support A2DP, as it's primarily used for music. Look on the box for A2DP, Advanced Audio Distribution Profile, or Bluetooth Stereo profile - I've seen it called any one of those three.

IPad3 64gb WiFi & the Jabra Halo Headset

Is the iPad3 64gb WiFi Cellular compatible with the Jabra Halo Headset. Please note not the Jabra Halo2.I have a Jabra Halo being delivwered. I'm running iOS 5.1.1 I've read a few articles that said that they werre compatible , but have since read a few that says they aren't after I'd spent the money.

Hi , and Thanks for that . Unfortunately , it made no difference . According to iTunes I have successfully restored the iPad 3 but the problems are :
1) No response from the screen . Slide to Open etc do not work .
2) Audio Controls at the top of the screen appear randomly and flash and alternate with the clock . The Volume slider moves up and down all on its own while each of the other buttons are highlighted one after the other !
3) The few photos on board roll along on a permanent Slideshow .
4) A black bar , the same size as the Slide to Open bar , containing and exclamation mark and the words ' No Sim Card Installed ' has appeared in the middle of the screen . Inserting a Sim card has no effect .
5) Brightness flickers as if its own Slider Control is being moved up and down .
6) Basically , its now a brick . I cant gain access without the screen and cant properly shut it down without the ' Off' slider working !
7) Very disappointing with something < one month old
M~

New iphone compatible w Jabra JX10 headset?

I cannot pair my iphone with my Jabra JX10 headset. I have the Jabra in discoverable mode (solid blue light on). The Iphone recognizes it and the words "Jabra JX10" and "now discoverable" appear, but it never pairs. yet the Jabra pairs successfully with both my old motorola and my husband's LG.
Any suggestions?

Vicki,
Take the iPhone to an Apple retail store and have a Mac Genius take a look at it. The Genius will be able to test the headset with another iPhone or test your iPhone with an iPhone Bluetooth Headset.
http://www.apple.com/retail/geniusbar/
Jason

Jabra Bluetooth Headset & iPhone

I have a Jabra Bluetooth headset that worked fine with my Sprint PCS Katana phone. I just got an iPhone yesterday. I go through the proper settings path and turn on bluetooth on the iPhone, it activates and reads "discoverable," but after several minutes still never found the headset. What can I do?
I also realize that I may have a difficult time locating any PIN for the headset (I bought it a year ago). Any solution for that?

As far as the pairing goes (from memory):
Turn headset off.
Press and hold power switch for a long time until the power light goes solid.
Use iPhone to pair.
(I believe PIN is 0000 or 9999)

Plantronics Savi W740 and Cisco CP-7942G

I am wondering if anyone has experienced this condition. We have a Call Center UCCX Version 8.0.2.11005-20 using Cisco CP-7942G hardware revision 13.0 phone running firmware SCCP42.9-3-1SR3-1S connected to Cisco Unified Communication Manager 8.0.3.20000-2. They have a Plantronics Savi W740 which is a Plantronics WO2 base connected using APC-41 EHS Cable. The also have the usb connected to the computer. Intermittently these will go into a state where the Line button on the phone is flashing and it appears to be going offhook and on-hook repeatedly. In order to break this condition they disconnect the headset. I am convinced it's the headset and not the CAD software through the computer doing this. I am wondering if anyone else has had this issue and what you did to resolve. I am also trying to figure out if the EHS cable is sending a signal that is getting logged that I can prove if it's sending the signal repeatedly or once.

Hi, this was posted a while ago I guess but we do experience the same issue, with 7962 phones running on SIP fw, and Savi 710/720 headsets.
Did you find a solution to this ? I'm very much interested to learn !
Yves Labonté

Routing issue between Cisco Nexus and Cisco 4510 R+E Chassis

We have configured Cisco Nexus 7K9 as core and Cisco 4510 R+E as access switches for Server connectivity.
We are experiencing problem in terms of ARP learning and Ping issues between Cisco Nexus and end hosts.

Hi,
So you have N7k acting as L3 with servers connected to 4510?.
Do you see the MAC associated with failing ARP in 4510?. Is it happening with all or few servers?. Just to verify if it is connectivity issue between N7k and 4510, you can configure an SVI on 4510 and assign address from same raneg (server/core range) and perform a ping.
This will help narrow down if issue is between server to 4510 or 4510 to N7k.
Thanks,
Nagendra

Mavericks VPN dropouts with native VPN client and Cisco IPSec

Since update to Maverics I am experiencing VPN dropouts with native VPN client and Cisco IPSec
I am connecting via a WIFI router to a remote VPN server
The conenction is good for a while but eventually it drops out.
I had Zero issues in mountain lion and only have issues since the update to 10.9
I had similar issues in teh past with an unrelaibel wifi router but i am using a Verizon Fios router and it has worked impecably until mavericks
My thoughts are:
1 -issue with mavericks ( maybe the app sleep funciton affecting eithe VPN or WIFI daemons)
2- Issue with cisco router compaitibility or timing with Cisco IPSEC
3- Issue with WIFI itself on mavericks - some sort of WIFI software bug
Any thousuggestions?

Since update to Maverics I am experiencing VPN dropouts with native VPN client and Cisco IPSec
I am connecting via a WIFI router to a remote VPN server
The conenction is good for a while but eventually it drops out.
I had Zero issues in mountain lion and only have issues since the update to 10.9
I had similar issues in teh past with an unrelaibel wifi router but i am using a Verizon Fios router and it has worked impecably until mavericks
My thoughts are:
1 -issue with mavericks ( maybe the app sleep funciton affecting eithe VPN or WIFI daemons)
2- Issue with cisco router compaitibility or timing with Cisco IPSEC
3- Issue with WIFI itself on mavericks - some sort of WIFI software bug
Any thousuggestions?

Communication problem between Cisco 3560 and Cisco SG300.

Dear Support,
I have a Cisco SG300 and Cisco 3560 switches.
3560 is my Core Switch and SG300 is access switch.
From 3560 VLAN information is not passed to SG300.
3560 Configuration:
interface GigabitEthernet0/23
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,2,10,11
switchport mode trunk
SG300 Configuration:
interface gigabitethernet49
spanning-tree link-type point-to-point
switchport mode general
switchport general allowed vlan add 2,10-11 tagged
macro description switch
Please suggest how this issue is resolve.
Regards,
JItesh Mahajan.

Dear Aleksandra,
Below Configuration is right or wrong for 3560 and SG300.
3560 Configuration:
interface GigabitEthernet0/23
switchport trunk encapsulation dot1q
switchport trunk allowed vlan remove VLAN 1
switchport native vlan 1
switchport trunk allowed vlan 1,2,10,11
switchport mode trunk
SG300 Configuration:
interface gigabitethernet49
spanning-tree link-type point-to-point
switchport mode general
switchport general allowed vlan add 2,10-11 tagged
macro description switch
Regards,
JItesh Mahajan.

Site-to-Site VPN between Cisco ASA 5505 (8.4) and Cisco Router (IOS 15.2)

Hi, I'm trying to create Site-to-Site VPN between Cisco ASA 5505 and Cisco Router 3945.
I've tried create configuration with and without ASA wizard, but anyway it doesn't work.
Please help me to find where is the issue.
I have two sites and would like to get access from 192.168.83.0 to 192.168.17.0
192.168.17.0 --- S1.S1.S1.S1 (IOS Router) ==================== S2.S2.S2.S2 (ASA 5505) --- 192.168.83.0
Here is my current configuration.
Thanks for your help.
IOS Configuration
version 15.2
crypto isakmp policy 1
encr aes 256
authentication pre-share
group 2
crypto isakmp key cisco address 198.0.183.225
crypto isakmp invalid-spi-recovery
crypto ipsec transform-set AES-SET esp-aes esp-sha-hmac
mode transport
crypto map static-map 1 ipsec-isakmp
set peer S2.S2.S2.S2
set transform-set AES-SET
set pfs group2
match address 100
interface GigabitEthernet0/0
ip address S1.S1.S1.S1 255.255.255.240
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
crypto map static-map
interface GigabitEthernet0/1
ip address 192.168.17.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
access-list 100 permit ip 192.168.17.0 0.0.0.255 192.168.83.0 0.0.0.255
ASA Configuration
ASA Version 8.4(3)
interface Ethernet0/0
switchport access vlan 2
interface Vlan1
nameif inside
security-level 100
ip address 192.168.83.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address S2.S2.S2.S2 255.255.255.248
ftp mode passive
same-security-traffic permit intra-interface
object network inside-network
subnet 192.168.83.0 255.255.255.0
object network datacenter
host S1.S1.S1.S1
object network datacenter-network
subnet 192.168.17.0 255.255.255.0
object network NETWORK_OBJ_192.168.83.0_24
subnet 192.168.83.0 255.255.255.0
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any log
access-list outside_cryptomap extended permit ip 192.168.83.0 255.255.255.0 object datacenter-network
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpn_pool 192.168.83.200-192.168.83.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic inside-network interface
nat (inside,outside) source static inside-network inside-network destination static inside-network inside-network no-proxy-arp route-lookup
nat (inside,outside) source static inside-network inside-network destination static datacenter-network datacenter-network no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.83.0_24 NETWORK_OBJ_192.168.83.0_24 destination static datacenter-network pdatacenter-network no-proxy-arp route-lookup
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 DEFAULT_GATEWAY 1
crypto ipsec ikev1 transform-set vpn-transform-set esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set vpn-transform-set mode transport
crypto ipsec ikev1 transform-set L2L_SET esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set L2L_SET mode transport
crypto dynamic-map dyno 10 set ikev1 transform-set vpn-transform-set
crypto map vpn 1 match address outside_cryptomap
crypto map vpn 1 set pfs
crypto map vpn 1 set peer S1.S1.S1.S1
crypto map vpn 1 set ikev1 transform-set L2L_SET
crypto map vpn 20 ipsec-isakmp dynamic dyno
crypto map vpn interface outside
crypto isakmp nat-traversal 3600
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
group-policy GroupPolicy_S1.S1.S1.S1 internal
group-policy GroupPolicy_S1.S1.S1.S1 attributes
vpn-tunnel-protocol ikev1
group-policy remote_vpn_policy internal
group-policy remote_vpn_policy attributes
vpn-tunnel-protocol ikev1 l2tp-ipsec
username artem password 8xs7XK3To4s5WfTvtKAutA== nt-encrypted
username admin password rqiFSVJFung3fvFZ encrypted privilege 15
tunnel-group DefaultRAGroup general-attributes
address-pool vpn_pool
default-group-policy remote_vpn_policy
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group S1.S1.S1.S1 type ipsec-l2l
tunnel-group S1.S1.S1.S1 general-attributes
default-group-policy GroupPolicy_S1.S1.S1.S1
tunnel-group S1.S1.S1.S1 ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f55f10c19a0848edd2466d08744556eb
: end

Thanks for helping me again. I really appreciate.
I don't hve any NAT-exemptions in Cisco IOS Router. Transform-set I will change soon, but I've tried with tunnel mode and it didn't work.
Maybe NAT-exemptions is the issue. Can you advice me which exemptions should be in Cisco IOS Router?
Because on Cisco ASA I guess I have everything.
Here is show crypto session detail
router(config)#do show crypto session detail
Crypto session current status
Code: C - IKE Configuration mode, D - Dead Peer Detection
K - Keepalives, N - NAT-traversal, T - cTCP encapsulation
X - IKE Extended Authentication, F - IKE Fragmentation
Interface: GigabitEthernet0/0
Session status: DOWN
Peer: 198.0.183.225 port 500 fvrf: (none) ivrf: (none)
      Desc: (none)
      Phase1_id: (none)
IPSEC FLOW: permit ip 192.168.17.0/255.255.255.0 192.168.83.0/255.255.255.0
        Active SAs: 0, origin: crypto map
        Inbound: #pkts dec'ed 0 drop 0 life (KB/Sec) 0/0
        Outbound: #pkts enc'ed 0 drop 0 life (KB/Sec) 0/0
Should I see something in crypto isakmp sa?
pp-border#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst             src             state          conn-id status
IPv6 Crypto ISAKMP SA
Thanks again for your help.

My MacBook Pro with Lion 10.7.2, only audio on the headset, and speaker mute. With Windows, the audio works in speaker and headphone jack. What is the problem? What's the solution?

My MacBook Pro with Lion 10.7.2, only audio on the headset, and speaker mute. With Windows, the audio works in speaker and headphone jack. What is the problem? What's the solution?

There is probably a red light on inside your headphone port, indicating that the analog/digital switch in there is stuck in the digital position. Insert a headphone plug and wigle it around, especially in the horizontal plane, as you insert and remove it several times. This will usually unstick the switch and restore normal operation. If it doesn't, the machine will need to be repaired.
This has been a fairly common problem, but in most cases it is easily cured as described above.

Can I use more than one blue-tooth device at the same time on IPhone 4S? Like a wireless headsets and speed and cadence sensor for cycling computer, receive the data and listen music simultaneously

Can I use more than one blue-tooth device at the same time on IPhone 4S? Like a wireless headsets and speed and cadence sensor for cycling computer, receive the data and listen music simultaneously

As long as the profiles are different (ex. HID vs AD2P) you will not have any issues. But say if you try to use 2 keyboards at once, it won't work. Or 2 headsets at once. Your scenario seems fine.

Jabra GN9120 headset and Cisco 7970G

Similar Messages

Maybe you are looking for