Jabra headset and Cisco 7942 Aux port

Hi ,
Two of our employees are using Jabra headsets. They are currently working over the analog headset port, but they would like to use the digital converter cable the headset came with to improve performance. How should I turned it on to utilize the auxiliary port in behind the phone.
Head model: Jabra GN9300e
Phone model: 7942
Any help would be much appreciated.
Saima

Hi Saima,
With the Cisco 7942, you would leverage the setting under
the product specific porting of the config via device>phone
and set Wireless Headset Hookswitch Control to Enabled
http://headsetplus.com/PDF/Jabra-EHS-guide.pdf
Cheers!
Rob
"And if I should fall behind
Wait for me" - Springsteen

Similar Messages

Cisco asr1000 aux-port

Hi. I have a Cisco ASR 1006 Router, with the the aux-port connected but i can´t configure the "line aux 0".. the line does not exist in the running config.
http://www.cisco.com/c/en/us/td/docs/routers/asr1000/install/guide/asr1routers/asr1higV8/asr1_hw2.html
In the related link Cisco says "The AUX port is a diagnostics access port".
I need to connect Cisco ASR1000 Aux-port with a Cisco CRS Console-Port as a second remote control method.
I Wish to confirm this before deploy several sites in the same way.
Thanks

Hi Saima,
With the Cisco 7942, you would leverage the setting under
the product specific porting of the config via device>phone
and set Wireless Headset Hookswitch Control to Enabled
http://headsetplus.com/PDF/Jabra-EHS-guide.pdf
Cheers!
Rob
"And if I should fall behind
Wait for me" - Springsteen

Is it possible to use Cisco 1721 AUX port to dial into MS-RAS?

Is it possible to use Cisco 1721 AUX port with external modem to dial into Microsoft W2k-RAS server?

Hello Thanks for the link. The place where I'm stuck is when the async is going through the LCP negotiation. the LCP Confreg sends but I dont' get back anything. Cisco documentation states "make sure autoselect PPP or Async mode dedicated are set but I'm actually dialing into a Microsoft RAS server. Do you know where these settings are?
*Mar 1 05:38:04.782: As65 PPP: Phase is ESTABLISHING, Active Open
*Mar 1 05:38:04.782: As65 PPP: No remote authentication for call-out
*Mar 1 05:38:04.782: As65 LCP: O CONFREQ [Closed] id 43 len 20
*Mar 1 05:38:04.782: As65 LCP: ACCM 0x000A0000 (0x0206000A0000)
*Mar 1 05:38:04.782: As65 LCP: MagicNumber 0x314EFEBB (0x0506314EFEBB)
*Mar 1 05:38:04.786: As65 LCP: PFC (0x0702)
*Mar 1 05:38:04.786: As65 LCP: ACFC (0x0802)
*Mar 1 05:38:06.782: As65 LCP: TIMEout: State REQsent
*Mar 1 05:38:06.782: As65 LCP: O CONFREQ [REQsent] id 44 len 20
*Mar 1 05:38:06.782: As65 LCP: ACCM 0x000A0000 (0x0206000A0000)
*Mar 1 05:38:06.782: As65 LCP: MagicNumber 0x314EFEBB (0x0506314EFEBB)
*Mar 1 05:38:06.782: As65 LCP: PFC (0x0702)
*Mar 1 05:38:06.782: As65 LCP: ACFC (0x0802)
*Mar 1 05:38:08.782: As65 LCP: TIMEout: State REQsent
*Mar 1 05:38:08.782: As65 LCP: O CONFREQ [REQsent] id 45 len 20
*Mar 1 05:38:08.782: As65 LCP: ACCM 0x000A0000 (0x0206000A0000)
*Mar 1 05:38:08.782: As65 LCP: MagicNumber 0x314EFEBB (0x0506314EFEBB)
*Mar 1 05:38:08.782: As65 LCP: PFC (0x0702)
*Mar 1 05:38:08.782: As65 LCP: ACFC (0x0802)

Jabra GN9120 headset and Cisco 7970G

I purchased a GN9120 wireless headset and tried to install it on my Cisco 7970G IP phone. But when I use it, the far end user always hears echoing.
Does anyone have the experience of using GN9120?
What is the proper setting for GN9120 to make it works with my Cisco phone?

Did you ever find a solution for this?

Jabra headset and iPhone issue

I have connected my iPhone to Jabra Extreme BT headset. But I can't hear SMS tone receiving. Is there any setting that resolve this

Hi Saima,
With the Cisco 7942, you would leverage the setting under
the product specific porting of the config via device>phone
and set Wireless Headset Hookswitch Control to Enabled
http://headsetplus.com/PDF/Jabra-EHS-guide.pdf
Cheers!
Rob
"And if I should fall behind
Wait for me" - Springsteen

IPhone 3g and aux port

Hi Everyone,
I bought an 3.5mm cable to connect my iPhone to the Aux port on my car's radio. The playback works but only seems to play from one speaker. Is there a setting on the iPhone that I'm missing or do I need to play around with the settings on my car stereo?
Thanks

It was a cable issue. The cable I had was mono not stereo. Got the correct cable and it's working fine

Configuring - Cisco 2921 with Switch Module/POE PS and 3750-x 24 port switch

This is what I have
- Cisco 2921 router
         with SM-ES2-24-P switch module and
                 POE power supply
-Cisco 3750x- 24 port Switch
I have port G1/0 (which connects to 24p Switch Module port g0/26 logically) configured with 3 sub interfaces (management, User and VOIP)
I want to connect 3750x to G0/1 on 2921 via fiber GBIC but want to use same three VLANs
I can not daisy chain 3750x via the switch module because it does not have fiber port.
I do not want to create another routed (g0/1) interface because I want to keep Users on both switches on the same subnet without further splitting the subnet in two.
I hope I am not making this confusing.
How can I bridge g1/0 and g0/1 so I can pass vlan traffic between two switches?
Second problem i have is ...
I have a VOIP connected to switch module (SM) and it is not getting any power.
I went in to all the interfaces on SM and issued power inline auto command
On the SM (sh power inline) - available is 0.0(w)
on the 2921 (sh power inline)
   - power supply status is good,
   - maximun power available is 280.
   - interface G1/0( which connects to SM)
      *device is unknown
      * powered off
     * allocated 0.0 watts.
I already tried resetting SM
Is there any other command I need to issue?
thanks for your help.

I'm having a similar issue. I can get trunked connectivity between the switch module and the router if I put the IP address on the router sub interface, but not if I put it on a VLAN interface. I was hoping to have it on a VLAN sub interface on the router so I could use Gig0/1 and Gig0/2 to connect other switches and have them on the same VLANs. I'm using Gig1/0 on the router side and Gig0/51 on the switch side (48-port module).
Any help? Am I on the wrong track altogether?

Telnet to router through AUX port

i have configured my router to telnet through modem dialin but when i dials from my pc to router it give me garbage charcter in my hyperterminal. can any one help me that is this is problem with my router configuration or the cable connection with the router.
router AUX port --> ciscoconsole cable --> cisco 29-4043-01-->modem

Even though the AUX port is supposed to "auto-baud" (usually you need to hit the "Enter" key a couple times), some/many/most/all current modems will set the DTE speed (the console cable) to the DCE speed (the modem-to-modem link) ... and "auto-baud" doesn't always work.
Since the modems will (by default) connect at 56K (or the top speed), chances are that it will try to talk to your Cisco device at some baud above 9.6K, which it is probably expecting.
You can do one of a couple things:
Hard set the modems to a 9.6k DTE speed (and/or DCE speed, since you won't go faster then the slowest baud)
OR
Experiment on the router to hard set the DTE speed to the baud set on the modem's serial port (frequently 115 kilobaud).
Check it out and get back to us.
Good Luck
Scott

Connection a RS232 device to the Aux port.

Dear,
I have a home lab wthe a 2600 access server (16 port octal).
From this 2600 router I want to connect to a Raritan 8 ports RPC.
This RPC (Remote power control) has a rs232 serial port (RJ45)
I tried a lot and still I do not get connected to the RPC, has anyone ever done this before.
When I use a rs232 serial cable from the RPC to my serial pc port, I get into the rpc directly when putty is opened.
pinout RPC
Pinout Aux (cisco)
Pinout rs-232 (db9)
1 DTR
1 RTS
1 DCD
2 GND
2 DTR
2 RX
3 RTS
3 TX
3 TX
4 TX
4 GND
4 DTR
5 RX
5 GND
5 GND
6 -
6 RX
6 DSR
7 GND
7 DSR
7 RTS
8 DCD
8 CTS
8 CTS
9 RI (ring indicator)
I created several cables without succes.
I connected RTS to CTS and DTR to DSR.
On aux port I used the following.
speed 9600 8n1
transport all
modem inout
(also tried with modem printer)
I'm missing something to get is working.
Any help?
Kind regards,
Remko

If you attach this USB drive to your Mac can it be accessed now?

Aux port configuration

Hi,
I have a following configuration:
Router AUX port -> FW Console
If there is something problem in the FW I can log the FW from cisco aux but the problem is now that the aux port is sending character's to FW's console port and now if the FW is rebooting it will go bootloop because when the FW boot's there is situation where is something "press any key" and now cisco router sends characters and the FW boots again.
Router AUX port config is following:
line aux 0
no exec
transport input all
stopbits 1
Which aux-port config the Cisco won't send any character to FW's console.
br
J

Hi Jody,
Thanks for your reply.
Actually I have no logging console configured at router but I will configure this also to the FW..I forgot to configure this at FW :)

Out-of-band dialin to AUX port

Hi
Setting up a modem to dial into on the AUX port has been a nightmare. I have the following configured on R1:
line aux 0
password cisco
login
modem inout
speed 115200
flowcontrol hardware
transport input all
modem auto configure type default
I then have to reverse telnet to the modem, this being necessary for a remote dialin to connect to the aux port. However, when I dialin from a remote pc using the normal Microsoft dial-up connection, I get a black window with a blinking prompt but I'm unable to type in window. If I enter a command in the window, I can see it being entered into the modem of the AUX port. If I click the button called DONE on this screen, it gets stuck on "verifying username and password". The reverse consol session then shoots out garbage characters and connection drops.
All I want is a simple out-of-band dialin to connect to a remote router. I have spent 2 valuable days on this and gone through all documentation. Is it my dial-up connection or the modem (the modem is a standard 56k V.92/V.90 with NO dip switches only software switches). The only AT command I've used is the at&f1s0=1 I simply cannot get hold of a USRobotics modem in this country. I have tried connecting at 9600 but that doesn't work.
Help please
Marcus

look here http://www.cisco.com/en/US/tech/tk801/tk36/tech_configuration_examples_list.html

Connectivity issues between Cisco 2901 and Cisco SG300-52

Hello,
I am having some serious connectivity issues between the hosts in my LAN.
My LAN is based on a Cisco 2901 router and a Cisco SG300-52 port switch.
The issue that has been happening is that connections between hosts on the LAN (remote desktop, extended ping, etc) is very unstable, at some point I can see a 35% lost packets on an extended ping. This happens at any time of the day and from any host.
All hosts are on the same Vlan(default Vlan) and on the same subnet. Some hosts have fixed IP addresses (servers and network equipment) and others obtain their IP address trough a DHCP reservation established on the router (reserved with the MAC address of every host).
I can provide further details if needed, because this issue is very serious and I would really appreciate any insight or support.
Many thanks in advanced.
Sair Amer
EDIT: After doing every test we could think of, we finally found the reason behind this problem.
It turns out that the switch has problems handling communications between clients at different speeds, because most of the hosts connected were working at 100 Mbps but the servers were working at 1000 Mbps (and the communication between host and servers wasn't stable).
After manually setting the speed on all ports to 100 Mbps the problems have stopped.
Many thanks for you help on this issue.

Building configuration...
Current configuration : 4123 bytes
! Last configuration change at 12:06:16 PCTime Sat Jul 19 2014 by ccp
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Foninsa
boot-start-marker
boot-end-marker
no logging buffered
enable secret 5 $1$BDbJ$HN3VP8nmywrGB55RCxPd30
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
clock timezone PCTime -4 0
clock summer-time PCTime date Apr 6 2003 2:00 Oct 12 2003 12:00
no ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.10
ip dhcp excluded-address 192.168.1.151 192.168.1.255
ip dhcp pool FONINSA
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 8.8.8.8 8.8.4.4
ip dhcp pool Laptop-Sporta-Wifi
host 192.168.1.10 255.255.255.0
ip name-server 8.8.8.8
ip name-server 8.8.4.4
no ipv6 cef
multilink bundle-name authenticated
crypto pki trustpoint TP-self-signed-213585710
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-213585710
revocation-check none
rsakeypair TP-self-signed-213585710
crypto pki certificate chain TP-self-signed-213585710
certificate self-signed 01
30820229 30820192
quit
license udi pid CISCO2901/K9 sn
license boot module c2900 technology-package securityk9
username ccp privilege 15 password
redundancy
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 190.196.21.98 255.255.255.248
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface GigabitEthernet0/1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
no ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 1 interface GigabitEthernet0/0 overload
ip nat inside source static tcp 192.168.1.3 21 190.196.21.98 21 extendable
ip nat inside source static tcp 192.168.1.3 80 190.196.21.98 80 extendable
ip nat inside source static udp 192.168.1.8 1194 190.196.21.98 1194 extendable
ip nat inside source static tcp 192.168.1.4 3389 190.196.21.98 3389 extendable
ip nat inside source static tcp 192.168.1.9 3389 190.196.21.98 10000 extendable
ip nat inside source static tcp 192.168.1.3 3389 190.196.21.98 20000 extendable
ip route 0.0.0.0 0.0.0.0 190.196.21.97
access-list 1 permit 192.168.1.0 0.0.0.255
control-plane
line con 0
password $
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 5
access-class 23 in
privilege level 15
password #
transport input telnet ssh
no scheduler allocate
end

Routing via AUX port

I have a dial-up modem connected to my router's AUX port.
Using this setup, I need to get remote users to access our internal servers via dial-up.
The users aren't network admins, so they should not have exec access to the routers. They only need to be able to access the servers on our system, i.e. I need to route their Laptops's traffic via the aux port to the intended server.
Is there a way of configuring the router and modem to do this? Or do I need more equipment in order for this to work?
The router is a 2960 series and the modem is a US Robotics dial up modem.
Any help is greatly appreciated. Thanks!

These configs are a bit old and crusty , but they should give you an idea on how to set up async routing on the AUX ports. As Paolo says , performance is not brilliant, but it will work ... The chat scripts would likely need to be modified to suit your particular modems -
#####DIALING SIDE############
username PRIROUTER password SAMEPASSWORDS
chat-script modem "" "atdt\T" TIMEOUT 60 CONNECT \c
chat-script rstusr "" "at&fs0=1e0&r2&d2&c1&b1&h1&m4&k1q0" "OK"
interface Async1
ip address 192.168.10.2 255.255.255.0
encapsulation ppp
async default routing
async mode interactive
dialer in-band
dialer string 5553731
dialer-group 1
ppp authentication chap
ip route 0.0.0.0 0.0.0.0 Async1
dialer-list 1 protocol ip permit
line aux 0
modem InOut
script reset rstusr
transport input all
flowcontrol hardware
script dialer modem
######RECEIVING SIDE##############
Username RouterA password cisco
interface Async1
ip address 192.168.10.1 255.255.255.0
encapsulation ppp
async default routing
async mode dedicated
dialer in-band
dialer-group 1
ppp authentication chap
ip route 0.0.0.0 0.0.0.0 async1
dialer-list 1 protocol ip permit
chat-script rstusr "" "at&fs0=1e0&r2&d2&c1&b1&h1&m4&k1q0" "OK"
line aux 0
modem InOut
script reset rstusr
transport input all
flowcontrol hardware

Communication problem between ASA 5510 and Cisco 3750, L2 Decode drops

Having problem with communication between ASA 5510 an Cisco Catalyst 3750.
Here is the Cisco switch port facing the ASA 5510 configuration:
interface FastEthernet2/0/6
description Trunk to ASA 5510
switchport trunk encapsulation dot1q
switchport trunk native vlan 50
switchport trunk allowed vlan 131,500
switchport mode trunk
switchport nonegotiate
And here is the ASA 5510 port configuration:
interface Ethernet0/3
speed 100
no nameif
no security-level
no ip address
interface Ethernet0/3.500
vlan 500
nameif outside
security-level 0
ip address X.X.X.69 255.255.255.0
There is a default route on ASA to X.X.X.1.
When I try to ping from ASA X.X.X.1 i get:
Sending 5, 100-byte ICMP Echos to 31.24.36.1, timeout is 2 seconds:
Also in the output of show interface eth 0/3 on the ASA i can see that the L2 Decode drop counter increases.
I have also changed the ports on the Switch and ASA but the same error stays.
Any thoughts?

I don't see anything wrong with your trunk configuration; I have a similar one working between an ASA 5520 and a Catalyst 3750G.
Maybe you should adjust the "speed 100"? In my experience, partial autoconfiguration results in duplex mis-matches, which results in dropped packets.
I'd try removing the "speed 100" and letting the ASA port autonegotiate with the switch. Alternatively, have both sides set
speed 100
duplex full
and see if things improve.
-- Jim Leinweber, WI State Lab of Hygiene

Site-to-Site VPN between Cisco ASA 5505 (8.4) and Cisco Router (IOS 15.2)

Hi, I'm trying to create Site-to-Site VPN between Cisco ASA 5505 and Cisco Router 3945.
I've tried create configuration with and without ASA wizard, but anyway it doesn't work.
Please help me to find where is the issue.
I have two sites and would like to get access from 192.168.83.0 to 192.168.17.0
192.168.17.0 --- S1.S1.S1.S1 (IOS Router) ==================== S2.S2.S2.S2 (ASA 5505) --- 192.168.83.0
Here is my current configuration.
Thanks for your help.
IOS Configuration
version 15.2
crypto isakmp policy 1
encr aes 256
authentication pre-share
group 2
crypto isakmp key cisco address 198.0.183.225
crypto isakmp invalid-spi-recovery
crypto ipsec transform-set AES-SET esp-aes esp-sha-hmac
mode transport
crypto map static-map 1 ipsec-isakmp
set peer S2.S2.S2.S2
set transform-set AES-SET
set pfs group2
match address 100
interface GigabitEthernet0/0
ip address S1.S1.S1.S1 255.255.255.240
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
crypto map static-map
interface GigabitEthernet0/1
ip address 192.168.17.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
access-list 100 permit ip 192.168.17.0 0.0.0.255 192.168.83.0 0.0.0.255
ASA Configuration
ASA Version 8.4(3)
interface Ethernet0/0
switchport access vlan 2
interface Vlan1
nameif inside
security-level 100
ip address 192.168.83.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address S2.S2.S2.S2 255.255.255.248
ftp mode passive
same-security-traffic permit intra-interface
object network inside-network
subnet 192.168.83.0 255.255.255.0
object network datacenter
host S1.S1.S1.S1
object network datacenter-network
subnet 192.168.17.0 255.255.255.0
object network NETWORK_OBJ_192.168.83.0_24
subnet 192.168.83.0 255.255.255.0
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any log
access-list outside_cryptomap extended permit ip 192.168.83.0 255.255.255.0 object datacenter-network
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpn_pool 192.168.83.200-192.168.83.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic inside-network interface
nat (inside,outside) source static inside-network inside-network destination static inside-network inside-network no-proxy-arp route-lookup
nat (inside,outside) source static inside-network inside-network destination static datacenter-network datacenter-network no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.83.0_24 NETWORK_OBJ_192.168.83.0_24 destination static datacenter-network pdatacenter-network no-proxy-arp route-lookup
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 DEFAULT_GATEWAY 1
crypto ipsec ikev1 transform-set vpn-transform-set esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set vpn-transform-set mode transport
crypto ipsec ikev1 transform-set L2L_SET esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set L2L_SET mode transport
crypto dynamic-map dyno 10 set ikev1 transform-set vpn-transform-set
crypto map vpn 1 match address outside_cryptomap
crypto map vpn 1 set pfs
crypto map vpn 1 set peer S1.S1.S1.S1
crypto map vpn 1 set ikev1 transform-set L2L_SET
crypto map vpn 20 ipsec-isakmp dynamic dyno
crypto map vpn interface outside
crypto isakmp nat-traversal 3600
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
group-policy GroupPolicy_S1.S1.S1.S1 internal
group-policy GroupPolicy_S1.S1.S1.S1 attributes
vpn-tunnel-protocol ikev1
group-policy remote_vpn_policy internal
group-policy remote_vpn_policy attributes
vpn-tunnel-protocol ikev1 l2tp-ipsec
username artem password 8xs7XK3To4s5WfTvtKAutA== nt-encrypted
username admin password rqiFSVJFung3fvFZ encrypted privilege 15
tunnel-group DefaultRAGroup general-attributes
address-pool vpn_pool
default-group-policy remote_vpn_policy
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group S1.S1.S1.S1 type ipsec-l2l
tunnel-group S1.S1.S1.S1 general-attributes
default-group-policy GroupPolicy_S1.S1.S1.S1
tunnel-group S1.S1.S1.S1 ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f55f10c19a0848edd2466d08744556eb
: end

Thanks for helping me again. I really appreciate.
I don't hve any NAT-exemptions in Cisco IOS Router. Transform-set I will change soon, but I've tried with tunnel mode and it didn't work.
Maybe NAT-exemptions is the issue. Can you advice me which exemptions should be in Cisco IOS Router?
Because on Cisco ASA I guess I have everything.
Here is show crypto session detail
router(config)#do show crypto session detail
Crypto session current status
Code: C - IKE Configuration mode, D - Dead Peer Detection
K - Keepalives, N - NAT-traversal, T - cTCP encapsulation
X - IKE Extended Authentication, F - IKE Fragmentation
Interface: GigabitEthernet0/0
Session status: DOWN
Peer: 198.0.183.225 port 500 fvrf: (none) ivrf: (none)
      Desc: (none)
      Phase1_id: (none)
IPSEC FLOW: permit ip 192.168.17.0/255.255.255.0 192.168.83.0/255.255.255.0
        Active SAs: 0, origin: crypto map
        Inbound: #pkts dec'ed 0 drop 0 life (KB/Sec) 0/0
        Outbound: #pkts enc'ed 0 drop 0 life (KB/Sec) 0/0
Should I see something in crypto isakmp sa?
pp-border#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst             src             state          conn-id status
IPv6 Crypto ISAKMP SA
Thanks again for your help.

Jabra headset and Cisco 7942 Aux port

Similar Messages

Maybe you are looking for