Jammer Detected
Hello all,
I have two 1310's running in bridge mode that at times encounter problems with dropping connection.
The only thing I see that may be at issue here is a large number of "Jammer Detected" however I can not seem to locate any information on it.
Any help?
Thanks!
Jammer Detected, is when the AP detects a sustained level of RF energy which it has determined is not 802.11.
Typically 2.4ghz phones, microwaves, etc. I had at one point a physically damaged nic which was just spewing RF, in the 2.4ghz spectrum.
Personally i used the congio spectrum expert to help me locate the issue. Any spectrum analyzer will help you locate the issue at hand.
Similar Messages
-
Need info about "sh int dot11Radio" and "sh int dot11Radio stati"
Hello,
Could someone explain me the counters in the 2 following display on an AP (like a AIR-AP1231G)
sh int dot11Radio 0
sh int dot11Radio 0 statistics
SiteR02#sh int dot11Radio 0
Dot11Radio0 is up, line protocol is up
Hardware is 802.11G Radio, address is 000f.3415.bf30 (bia 000f.3415.bf30)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:12, output 00:00:12, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/30 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
24680 packets input, 3282575 bytes, 0 no buffer
Received 129 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
23427 packets output, 4831674 bytes, 0 underruns
212 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
SiteR02#sh int dot11Radio 0 statistics
DOT11 Statistics (Cumulative Total/Last 5 Seconds):
RECEIVER TRANSMITTER
Host Rx Bytes: 3265473 / 0 Host Tx Bytes: 4338004 / 0
Unicasts Rx: 88699 / 1 Unicasts Tx: 27040 / 0
Unicasts to host: 88699 / 1 Unicasts by host: 23629 / 0
Broadcasts Rx: 0 / 0 Broadcasts Tx: 4601528 / 49
Beacons Rx: 0 / 0 Beacons Tx: 4601528 / 49
Broadcasts to host: 0 / 0 Broadcasts by host: 0 / 0
Multicasts Rx: 0 / 0 Multicasts Tx: 0 / 0
Multicasts to host: 0 / 0 Multicasts by host: 0 / 0
Mgmt Packets Rx: 0 / 0 Mgmt Packets Tx: 3411 / 0
RTS received: 0 / 0 RTS transmitted: 1721 / 0
Duplicate frames: 230 / 0 CTS not received: 1597 / 0
CRC errors: 4303 / 0 Unicast Fragments Tx: 26833 / 0
WEP errors: 0 / 0 Retries: 2540 / 0
Buffer full: 0 / 0 Packets one retry: 435 / 0
Host buffer full: 0 / 0 Packets > 1 retry: 174 / 0
Header CRC errors: 43265 / 0 Protocol defers: 2 / 0
Invalid header: 311 / 0 Energy detect defers: 206 / 0
Length invalid: 0 / 0 Jammer detected: 0 / 0
Incomplete fragments: 0 / 0 Packets aged: 0 / 0
Rx Concats: 0 / 0 Tx Concats: 0 / 0
RATE 2.0 Mbps
RATE 5.5 Mbps
RATE 11.0 Mbps
SiteR02#
Somes counters are displayed on those 2 displays but it is not with the same figure (CRC errors, input, output, broadcast, ...)
Can someone explaines me this ?
regards,Hello, do you know the formula ?
If I had errors to the "input field -from sh int-" then I don't get the unicats received field in the "sh int stat".
Regards, -
Aironet Power Injector -Air-Pwrinj-Blr2=
I am working with a Aironet Power Injector (Air-Pwrinj-Blr2=) trying to connect it to the access point it comes with to a desktop running Windows XP. I am able to connected to it and use cli commands via hyper terminal, but I am not able to get a network signal to the desktop. I was able to find the IP address or what I assume is the ip address, but can't ping it from inside the office and I am not able to use the ip address to get a connection to the power injector via browser. Has anybody worked with one of these units before this is a first for me and I am hoping somebody can steer me in the right direction and get this working. The Ethernet, Status and Radio are all blinking green lights on the access point and the Install is not used on this model so no light there. Thanks in advance for any help provided!
what error do you get when you http://10.0.0.1 ?
webpage cannot be displayed
seems to function cli mode fine?
it seems to, but I'm also not very familiar with this piece of equipment
I am also receiving a blinking green light under (E) Ethernet and also under (S) Status
the device does a sh tech?
Heres what I received from this command:
ap#sh tech
------------------ show version ------------------
Cisco IOS Software, C1310 Software (C1310-K9W7-M), Version 12.4(25d)JA, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 09-Dec-10 16:12 by prod_rel_team
ROM: Bootstrap program is C1310 boot loader
BOOTLDR: C1310 Boot Loader (C1310-BOOT-M) Version 12.3(2)JA4, RELEASE SOFTWARE (
fc1)
ap uptime is 4 weeks, 3 days, 21 hours, 11 minutes
System returned to ROM by power-on
System image file is "flash:/c1310-k9w7-mx.124-25d.JA/c1310-k9w7-mx.124-25d.JA"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-BR1310G-A-K9 (PowerPCElvis) processor (revision A0) with 25590K/71
68K bytes of memory.
Processor board ID FTX1220U0G1
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:21:55:CC:70:3A
Part Number : 73-8960-09
PCA Assembly Number : 800-24963-06
PCA Revision Number : A0
PCB Serial Number : FOC12171GGX
Top Assembly Part Number : 800-28764-01
Top Assembly Serial Number : FTX1220U0G1
Top Revision Number : A0
Product/Model Number : AIR-BR1310G-A-K9
Configuration register is 0xF
------------------ show running-config ------------------
Building configuration...
Current configuration : 1009 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
logging rate-limit console 9
enable secret 5
no aaa new-model
dot11 syslog
username Cisco password 7
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
shutdown
station-role root access-point
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp client-id FastEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
login local
end
------------------ show stacks ------------------
Minimum process stacks:
Free/Size Name
2612/6000 soap_flash init
11624/12000 Setup
5604/6000 Autoinstall
5564/6000 Clock Update Proc
5628/6000 dot11 platform init
8836/12000 Init
11308/12000 BootP Resolver
5456/6000 RADIUS INITCONFIG
10828/12000 DHCP Autoinstall
2544/3000 Rom Random Update Process
9628/12000 Exec
Interrupt level stacks:
Level Called Unused/Size Name
4 2428500 8164/9000 dot11 radio interrupt
6 9538 8860/9000 NS16550 VECTOR
------------------ show interfaces ------------------
BVI1 is up, line protocol is up
Hardware is BVI, address is 0021.55cc.703a (bia 0021.55b2.4d70)
Internet address will be negotiated using DHCP
MTU 1500 bytes, BW 54000 Kbit/sec, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
79221 packets input, 15586895 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
103299 packets output, 33985371 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
48621 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
Dot11Radio0 is administratively down, line protocol is down
Hardware is 802.11G Radio, address is 0021.55b2.4d70 (bia 0021.55b2.4d70)
MTU 1500 bytes, BW 54000 Kbit/sec, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/1127/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/30 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
FastEthernet0 is up, line protocol is up
Hardware is PowerPCElvis Ethernet, address is 0021.55cc.703a (bia 0021.55cc.70
3a)
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Full-duplex, 100Mb/s, MII
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:02, output hang never
Last clearing of "show interface" counters never
Input queue: 0/1127/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 1000 bits/sec, 1 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
2004070 packets input, 385155716 bytes
Received 2004070 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
424653 packets output, 66628823 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
32 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
------------------ show controllers ------------------
interface Dot11Radio0
Radio AIR-MP31G, Base Address 0021.55b2.4d70, BBlock version 0.00, Software vers
ion 6.30.25
Serial number: FOC1218B109
Number of supported simultaneous BSSID on Dot11Radio0: 16
Carrier Set: Americas (US) (-A)
Uniform Spreading Required: No
Configured Frequency: 0 MHz Channel 0
Allowed Frequencies: 2412(1) 2417(2) 2422(3) 2427(4) 2432(5) 2437(6) 2442(7) 244
7(8) 2452(9) 2457(10) 2462(11)
Listen Frequencies: 2412(1) 2417(2) 2422(3) 2427(4) 2432(5) 2437(6) 2442(7) 2447
(8) 2452(9) 2457(10) 2462(11) 2467(12) 2472(13) 2484(14)
Beacon Flags: 0, Interface Flags 60109, Interface Events 0, Mode 9; Beacons are
disabled; Probes are disabled
Configured CCK Power: 100 mW
Configured OFDM Power: 100 mW
Active power levels by rate
1.0 to 54.0 , 0 mW
OffChnl Power: 32767, Rate 1.0
Allowed CCK Power Levels: 1 5 10 20 30 50 100
Allowed OFDM Power Levels: 1 5 10 20 30 50 100
Allowed Client Power Levels: 1 5 10 20 30 50 100
Receive Antennas : right-a
Transmit Antennas : right-a
Antenna: internal, Gain: Allowed 4, Reported 4, In Use 4
Active Rates:
Current Rates: basic-1.0 basic-2.0 basic-5.5 basic-11.0 6.0 9.0 12.0 18.0 24.0
36.0 48.0 54.0
Allowed Rates: 1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
All Rates: 1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
Default Rates: basic-1.0 basic-2.0 basic-5.5 basic-11.0 6.0 9.0 12.0 18.0 24.0
36.0 48.0 54.0
Best Range Rates: basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
Best Throughput Rates: basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic
-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
Current Voice Rates: basic-5.5 basic-11.0 6.0 12.0 24.0 [disabled until voice p
acket-discard enabled]
Default Voice Rates: basic-5.5 basic-11.0 6.0 12.0 24.0
Managment Rates:
Multicast Rates:
Data Rate Sensitivity (rate, SNR dB, Contention dBm)
( 1.0, 1, -98) ( 2.0, 7, -94) ( 5.5, 9, -92) (11.0, 16, -86)
( 6.0, 7, -92) ( 9.0, 14, -87) (12.0, 12, -87) (18.0, 15, -84)
(24.0, 17, -82) (36.0, 24, -76) (48.0, 29, -73) (54.0, 33, -69)
ERP settings:.
Neighbors in non-erp mode:
Number of MFP Indices: 10
RFID Tag Detection: Disabled
Multicast Address filtered:
Packet type filtered:
Probe limit: active off, filter on, count 0, time 0
Assoc limit: active off, count 0, time 0
Radio Management (RM) Configuration: Regular AP, Mode 1, Disabled
MCST RSCs: [0]0x0 [1]0x0 [2]0x0 [3]0x0 [4]0x0 [5]0x0 [6]0x0 [7]0x0 [8]0x0
TKIP Cum Stats: STA MIC-L-Errs MIC-R-Errs Replay C-Measure
0000.0000.0000 00000000 00000000 00000000 00000000
AES-CCMP Cum Stats: 00000000 replays discarded
QBSS Load: 0x0, Policing Stats: Rx downgrades 0, Tx downgrades 0
Classifier Stats tx_on_up6 0, tx_on_up4 0
Configured Local Access Class Parameters
Back : cw-min 4 cw-max 10 fixed-slot 7 admission-control Off txop 0
Best : cw-min 4 cw-max 6 fixed-slot 3 admission-control Off txop 0
Video : cw-min 3 cw-max 4 fixed-slot 1 admission-control Off txop 3008
Voice : cw-min 2 cw-max 3 fixed-slot 1 admission-control Off txop 1504
Configured Cell Access Class Parameters
Back : cw-min 4 cw-max 10 fixed-slot 7 admission-control Off txop 0
Best : cw-min 4 cw-max 10 fixed-slot 3 admission-control Off txop 0
Video : cw-min 3 cw-max 4 fixed-slot 2 admission-control Off txop 3008
Voice : cw-min 2 cw-max 3 fixed-slot 2 admission-control Off txop 1504
SIP stats sip_udp_rx_pkt 0, sip_tcp_rx_pkt 0,
downlink classified_pkt 0,
uplink classified_pkt 0,
num_processed_SIP_Calls 0
Transmit queues: Limit 650 Current 0 In-Progress 0
---- Active --- In-Progress --------------- Counts --------------
Cnt Quo Bas Max Cnt Quo Bas Sent Discard Fail Retry Multi
Uplink 0 0 0 0 0 0 0 0 0 0 0 0
Voice 0 0 0 0 0 0 0 0 0 0 0 0
Video 0 0 0 0 0 0 0 0 0 0 0 0
Best 0 0 0 0 0 0 0 0 0 0 0 0
Back 0 0 0 0 0 0 0 0 0 0 0 0
BSSIDS Index Flags State Next Held Defer NonDefer Clients Tsf Dtim Txq
Driver TX blocks: in use 0, high 0, at reset 0, fail 0 drop 0
Off Channel Metrics: Timeouts - Tx 0 Beacon 0 DTIM MC Waits 0
---Clients AID VLAN Status Age Tx Mode Enc Key Rate
RxPkts KBytes Dup Dec Mic TxPkts KBytes Retry RSSI SNR
IP Address Pauses RSC
Video Report: Cnt Rate Retries/Tot
8021x auth in prog 0 allowed 0
Vlan BSSID Clients PSP Pri HT Encr Key0 Key1 Key2 Key3 SSIDs MFP
0n 0000 0 0 0 0 0 0
Protocol 55
Registers: io E8000000 mem 80000000 aux A0000000
0000 FF6A 0000 0000 0021 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0220 1A1C FFFF 0504
0000 0000 0000 0000 9936 0020 E5FF 73C9
00000000 18200340 30540041 BFFFF7FF FFFFFFEF 00000000 10840000 08008208
FFFFFDCE 00000FFF 9C6276F3 00690706 00000000 00000000 00008000 00008080
00000000 00000000 00000000 00000000 00000F7A 00000000 00000000 0000E6B4
Radio running: temp 0 C tx_power 0 bb_code 0x0
rssi_threshold 0x3E gain offset 0 platform 0
PCI sys_id: 0xA506 subsys_id 0x5500 (0x5501)
Unicast ciphers 0x0 mcast ciphers 0x0
Rid Ring:
A0000970: 01C08000 21D6A1BC * n
Rx Ring:
A0000950: 89380000 21BF493C * v, 89380000 21BF3EA8 v
A0000960: 89380000 21BF3414 v, 89380000 21BF2980 v
Tx Ring:
A0000800: 00000000 00000000 * n, 00000000 00000000 n
A0000810: 00000000 00000000 n, 00000000 00000000 n
A0000820: 00000000 00000000 n, 00000000 00000000 n
A0000830: 00000000 00000000 n, 00000000 00000000 n
A0000840: 00000000 00000000 n, 00000000 00000000 n
A0000850: 00000000 00000000 n, 00000000 00000000 n
A0000860: 00000000 00000000 n, 00000000 00000000 n
A0000870: 00000000 00000000 n, 00000000 00000000 n
A0000880: 00000000 00000000 n, 00000000 00000000 n
A0000890: 00000000 00000000 n, 00000000 00000000 n
A00008A0: 00000000 00000000 n, 00000000 00000000 n
A00008B0: 00000000 00000000 n, 00000000 00000000 n
A00008C0: 00000000 00000000 n, 00000000 00000000 n
A00008D0: 00000000 00000000 n, 00000000 00000000 n
A00008E0: 00000000 00000000 n, 00000000 00000000 n
A00008F0: 00000000 00000000 n, 00000000 00000000 n
A0000900: 00000000 00000000 n, 00000000 00000000 n
A0000910: 00000000 00000000 n, 00000000 00000000 n
A0000920: 00000000 00000000 n, 00000000 00000000 n
TxDn Ring:
A0000930: 802C0000 21D6A9C4 * v, 802C0000 21D6AAA4 v
A0000940: 802C0000 21D6AB84 v, 802C0000 21D6AC64 v
Multicast counters:
Internal MC counts:
0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0
(0) 0 (0) 0 (0)
-Channel Range- -------Rates------ Max Power Allowed
1 to 11 by 1 1.0 to 11.0 100 1 5 10 20 30 50 100
6.0 to 54.0 30
DOT11 Statistics (Cumulative Total/Last 5 Seconds):
RECEIVER TRANSMITTER
Host Rx K Bytes: 0 / 0 Host Tx K Bytes: 0 / 0
Unicasts Rx: 0 / 0 Unicasts Tx: 0 / 0
Unicasts to host: 0 / 0 Unicasts by host: 0 / 0
Broadcasts Rx: 0 / 0 Broadcasts Tx: 0 / 0
Beacons Rx: 0 / 0 Beacons Tx: 0 / 0
Broadcasts to host: 0 / 0 Broadcasts by host: 0 / 0
Multicasts Rx: 0 / 0 Multicasts Tx: 0 / 0
Multicasts to host: 0 / 0 Multicasts by host: 0 / 0
Mgmt Packets Rx: 0 / 0 Mgmt Packets Tx: 0 / 0
RTS received: 0 / 0 RTS transmitted: 0 / 0
Duplicate frames: 0 / 0 CTS not received: 0 / 0
CRC errors: 0 / 0 Unicast Fragments Tx: 0 / 0
WEP errors: 0 / 0 Retries: 0 / 0
Buffer full: 0 / 0 Packets one retry: 0 / 0
Host buffer full: 0 / 0 Packets > 1 retry: 0 / 0
Header CRC errors: 0 / 0 Protocol defers: 0 / 0
Invalid header: 0 / 0 Energy detect defers: 0 / 0
Length invalid: 0 / 0 Jammer detected: 0 / 0
Incomplete fragments: 0 / 0 Packets aged: 0 / 0
Rx Concats: 0 / 0 Tx Concats: 0 / 0
Multicast throttle drops: 0
Client TX pause count: 0
Media Direct Band Configuration
Unicast Video Redirect = 0
Client Min Phy Rate = 0
Max Retry Percentage = 0
Dot11 Current Video Transmission Metrics:
Arrivals:0 Q-Drops:0 Tries:0 Agg:0 Success:0 Fail:0
Dot11 5-second Video Transmission Metrics:
Arrivals:0 Tries:0 Agg:0 Success:0 Fail:0
Radio-Q-Peak:0 Video-Q-Peak:0 Video-Q-Drops:0
Delay - Tot Msec:0 10/20/40/40+ Msec:0/0/0/0
Dot11 1-second Video Transmission Metrics:
Q-util:0 max-tx-time:0 p-chan:0 p-video:0 L/r:0
Last radio reset code: 37
Radio resets - total:4 retries:0 failed:0
Reset Stats: -- Start Cnt: 1, Recovery: Cnt 0Last Ret: 200, Fails: 0, Recover
y Status: Stalled? NO, In Prog? NO
Code/Count: 37/00003 54/00001
Log Buffer:
PowerPCElvis Ethernet unit 0
PHY Hardware is Broadcom BCM5914 rev. 2 (id_register: 0x40, 0x6322)
rx_intr: 0 tx_intr: 0 mac_err_isr: 0 phy_link_isr:0
Current station address 0021.55cc.703a, default address 0021.55cc.703a
MAL register dump:
malcr 0x0007C082 0x180
malesr 0x00000000 0x181
malier 0x0000000F 0x182
maltxcasr 0x80000000 0x184
maltxcarr 0x80000000 0x185
maltxeobisr 0x00000000 0x186
maltxdeir 0x00000000 0x187
malrxcasr 0x80000000 0x190
malrxcarr 0x80000000 0x191
malrxeobisr 0x00000000 0x192
malrxdeir 0x00000000 0x193
maltxctp0r 0x01D6AEA0 0x1A0
malrxctp0r 0x01D6ADA0 0x1C0
malrcbs0 0x00000060 0x1E0
EMAC register dump:
emacmr0 0x18000000 0x00
emacmr1 0xA1788000 0x04
emactmr0 0x00000000 0x08
emactmr1 0x380F0000 0x0C
emacrmr 0x7D180000 0x10
emacisr 0x00000002 0x14
emacier 0x00000001 0x18
emaciah 0x00000021 0x1C
emacial 0x55CC703A 0x20
emacptr 0x0000FFFF 0x2C
emaclsah 0x00000000 0x50
emaclsal 0x00000000 0x54
emacipgr 0x00000004 0x58
emacstacr 0x002F8018 0x5C
emactrtr 0x18000000 0x60
emacrwmr 0x0F002000 0x64
emacoctx 0x041380E4 0x68
emacocrx 0x176FF93A 0x6C
UIC register dump:
uicsr 0x00009FB4 0xC0
uicer 0x803F0048 0xC2
uicmsr 0x00000000 0xC6
PHY register dump:
3000 782D 0040 6322 05E1 45E1 0005 2001 0000 0000 0000 0000 0000 0000 0000 0000
1000 0300 0000 0000 0200 008F 0400 0000 002F 8D1F 4400 008A 002F 0000 80A0
RX ring with 16 entries at 0x1D6ADA0, Buffer size 1524
Rxhead = 0x1D6ADF0 (10), Rxp = 0x111A11C (10)
00 pak=0x1060830 buf=0x1BF7E68 status=9C00 pak_size=0
01 pak=0x10604AC buf=0x1BF73D4 status=9C00 pak_size=0
02 pak=0x1060BB4 buf=0x1BF88FC status=9C00 pak_size=0
03 pak=0x105E88C buf=0x1BF1F34 status=9C00 pak_size=0
04 pak=0x105FA20 buf=0x1BF5418 status=9C00 pak_size=0
05 pak=0x1060128 buf=0x1BF6940 status=9C00 pak_size=0
06 pak=0x10620CC buf=0x1BFC874 status=9C00 pak_size=0
07 pak=0x105FDA4 buf=0x1BF5EAC status=9C00 pak_size=0
08 pak=0x1061640 buf=0x1BFA8B8 status=9C00 pak_size=0
09 pak=0x1062EDC buf=0x1BFF2C4 status=9C00 pak_size=0
10 pak=0x1060F38 buf=0x1BF9390 status=9C00 pak_size=0
11 pak=0x1061D48 buf=0x1BFBDE0 status=9C00 pak_size=0
12 pak=0x105E508 buf=0x1BF14A0 status=9C00 pak_size=0
13 pak=0x10627D4 buf=0x1BFDD9C status=9C00 pak_size=0
14 pak=0x10619C4 buf=0x1BFB34C status=9C00 pak_size=0
15 pak=0x10612BC buf=0x1BF9E24 status=DC00 pak_size=0
TX ring with 8 entries at 0x1D6AEA0, tx_count = 0
tx_head = 0x1D6AEB8 (3), head_txp = 0x111A15C (3)
tx_tail = 0x1D6AEB8 (3), tail_txp = 0x111A15C (3)
00 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
01 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
02 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
03 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
04 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
05 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
06 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
07 pak=0x0000000 buf=0x0000000 status=5400 pak_size=0
0 missed datagrams, 0 overruns
0 transmitter underruns, 0 excessive collisions
0 single collisions, 0 multiple collisions
0 dma memory errors, 0 CRC errors
0 alignment errors, 0 runts, 0 giants
emac/mal specific errors:
0 rx in range, 0 rx out range
0 mal_rx_serr, 0 mal_tx_serr
0 mal_rx_de, 0 mal_tx_de
0 emac_int
0 mal_err_isr
0 SQE errors, 0 tx CRC errors
0 output queue fail
------------------ show user ------------------
Line User Host(s) Idle Location
* 0 con 0 idle 00:00:23
Interface User Mode Idle Peer Address
------------------ show data-corruption ------------------
No data inconsistency errors have been recorded.
------------------ show file systems ------------------
File Systems:
Size(b) Free(b) Type Flags Prefixes
* 7483392 1940480 flash rw flash:
- - opaque rw bs:
7483392 1940480 unknown rw zflash:
- - opaque rw archive:
- - opaque rw system:
32768 31692 nvram rw nvram:
- - network rw tftp:
- - opaque rw null:
- - opaque ro xmodem:
- - opaque ro ymodem:
- - network rw rcp:
- - network rw ftp:
- - network rw http:
- - network rw scp:
- - network rw https:
------------------ show flash: all ------------------
Directory of flash:/
2 drwx 0 Mar 1 2002 23:49:39 +00:00 Test
3 drwx 256 Jan 1 1970 01:15:32 +00:00 c1310-k9w7-mx.124-25d.JA
152 -rwx 5 Mar 1 2002 00:15:39 +00:00 private-config
153 -rwx 1048 Mar 1 2002 00:15:39 +00:00 private-multiple-fs
154 -rwx 0 Mar 1 2002 00:00:03 +00:00 env_vars
7483392 bytes total (1940480 bytes free)
------------------ dir nvram: ------------------
Directory of nvram:/
30 -rw- 0 startup-config
31 ---- 0 private-config
1 -rw- 0 ifIndex-table
32768 bytes total (31692 bytes free)
------------------ show memory statistics ------------------
Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
Processor D2CB44 12389564 7066360 5323204 5237068 5256656
I/O 1900000 7340032 4632280 2707752 2707580 2707688
------------------ show process memory ------------------
Processor Pool Total: 12389564 Used: 7066272 Free: 5323292
I/O Pool Total: 7340032 Used: 4632268 Free: 2707764
PID TTY Allocated Freed Holding Getbufs Retbufs Process
0 0 11640760 831304 9313600 0 0 *Init*
0 0 12324 142912 12324 0 0 *Sched*
0 0 2259352 2409964 216696 4536992 4536992 *Dead*
0 0 0 0 1349016 0 0 *MallocLite*
1 0 10052 0 17064 0 0 Chunk Manager
2 0 196 196 4012 0 0 Load Meter
3 0 1034696 1032992 14768 0 0 Exec
4 0 3348 196 10164 0 0 Check heaps
5 0 0 0 7012 0 0 Pool Manager
6 0 196 196 7012 0 0 Timers
7 0 196 196 7012 0 0 AAA high-capacit
8 0 0 0 7012 0 0 AAA_SERVER_DEADT
9 0 0 0 13012 0 0 Policy Manager
10 0 0 0 25012 0 0 Crash writer
11 0 0 0 7012 0 0 RO Notify Timers
13 0 0 0 7012 0 0 ARP Input
14 0 588 0 7600 0 0 Entity MIB API
15 0 0 0 7012 0 0 HC Counter Timer
16 0 196 196 7012 0 0 GraphIt
17 0 0 0 7012 0 0 Net Input
18 0 0 0 7012 0 0 Critical Bkgnd
19 0 21704 152 13528 0 0 Net Background
20 0 68328420 68328420 13012 0 0 IDB Work
21 0 196 196 13012 0 0 Logger
22 0 92460 748 7136 0 0 TTY Background
23 0 0 0 10012 0 0 Per-Second Jobs
25 0 0 0 7012 0 0 Transport Port A
26 0 196 196 7012 0 0 Compute load avg
27 0 0 1056 7012 0 0 Per-minute Jobs
28 0 196 196 7012 0 0 Dot11 Install Mo
29 0 196 196 7012 0 0 sys monitor
30 0 196 196 7012 0 0 Power Injector m
31 0 196 196 7012 0 0 Dot11 driver
32 0 196 196 7012 0 0 Dot11 dumper
33 0 196 196 7012 0 0 Dot11 driver log
34 0 0 0 7012 0 0 Voice Metrics Ta
35 0 0 0 7012 0 0 SOAP LED Process
36 0 196 196 7012 0 0 AAA Server
37 0 0 0 7012 0 0 AAA ACCT Proc
38 0 0 0 7012 0 0 ACCT Periodic Pr
39 0 0 0 13012 0 0 IP Input
40 0 0 0 7012 0 0 ICMP event handl
42 0 196 196 7012 0 0 AAA Dictionary R
43 0 656 196 7472 0 0 CDP Protocol
44 0 0 0 7012 0 0 linktest
45 0 196 196 10012 0 0 Dot11 aaa proces
46 0 0 0 10012 0 0 pmkid
47 0 196 196 7012 0 0 Dot11 Mgmt & Ass
48 0 196 196 7012 0 0 DOT11 MFP IO
49 0 1324 196 8140 0 0 AiroIAPP Protoco
50 0 196 196 7012 0 0 Triggered events
51 0 196 196 10012 0 0 Dot11 auth Dot1x
52 0 0 0 7012 0 0 Dot11 Mac Auth
53 0 748 0 7760 0 0 Dot11CACprocess
54 0 196 196 7012 0 0 Dot1x Mgr Proces
55 0 0 0 7012 0 0 MAB Framework
56 0 0 0 7012 0 0 EAP Framework
57 0 0 0 7012 0 0 EAP Test
58 0 0 0 13012 0 0 TCP Timer
59 0 0 0 13012 0 0 TCP Protocols
60 0 0 0 7012 0 0 Socket Timers
61 0 0 0 7012 0 0 IP Traceroute
62 0 800 0 7812 0 0 L2MM
63 0 0 0 7012 0 0 MRD
64 0 0 0 7012 0 0 IGMPSN
65 0 3244 0 13256 0 0 HTTP CORE
66 0 1096 196 13912 0 0 Soap Upgrade fet
67 0 10540 196 17356 0 0 DDP
68 0 196 196 7012 0 0 WLCCP MFP AP
69 0 360 196 7176 0 0 Dot1x Supplicant
70 0 360 196 7176 0 0 Dot1x Supplicant
71 0 360 196 7176 0 0 Dot1x Supplicant
72 0 196 196 7012 0 0 LOCAL AAA
73 0 196 196 7012 0 0 AAA Cached Serve
74 0 196 196 7012 0 0 ENABLE AAA
75 0 196 196 7012 0 0 LINE AAA
76 0 66600 196 7828 0 0 TPLUS
77 0 392 196 9208 0 0 Crypto WUI
78 0 0 0 7012 0 0 EM Background Pr
79 0 0 0 13012 0 0 encrypt proc
80 0 196 196 7012 0 0 Soap Consoleless
81 0 66960 66184 13788 0 0 Crypto CA
82 0 0 0 13012 0 0 Crypto PKI-CRL
83 0 0 0 9012 0 0 Crypto SSL
84 0 0 0 7012 0 0 crypto engine pr
85 0 196 196 7012 0 0 AAA SEND STOP EV
86 0 196 196 7012 0 0 Dot11 LBS Proc
87 0 0 0 7012 0 0 Syslog Traps
88 0 196 196 7012 0 0 Radio Temperatur
89 0 3724 3724 13012 0 0 Syslog
92 0 0 32495900 13012 0 0 DHCP Client
94 0 196 196 13044 0 0 HyBridge Input P
95 0 512 348 7360 0 0 Tbridge Monitor
96 0 5412 5248 13208 0 0 Spanning Tree
97 0 33453996 3480 7012 0 0 RAC I/F Conf.
11695864 Total
------------------ show process cpu ------------------
CPU utilization for five seconds: 0%/0%; one minute: 0%; five minutes: 0%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
1 0 3 0 0.00% 0.00% 0.00% 0 Chunk Manager
2 51 550818 0 0.00% 0.00% 0.00% 0 Load Meter
3 475 565 840 0.24% 0.37% 0.10% 0 Exec
4 1253541 281225 4457 0.00% 0.05% 0.05% 0 Check heaps
5 0 1 0 0.00% 0.00% 0.00% 0 Pool Manager
6 0 2 0 0.00% 0.00% 0.00% 0 Timers
7 0 2 0 0.00% 0.00% 0.00% 0 AAA high-capacit
8 0 1 0 0.00% 0.00% 0.00% 0 AAA_SERVER_DEADT
9 0 1 0 0.00% 0.00% 0.00% 0 Policy Manager
10 0 1 0 0.00% 0.00% 0.00% 0 Crash writer
11 1 1 1000 0.00% 0.00% 0.00% 0 RO Notify Timers
13 33858 80352 421 0.00% 0.00% 0.00% 0 ARP Input
14 1 2 500 0.00% 0.00% 0.00% 0 Entity MIB API
15 22 826230 0 0.00% 0.00% 0.00% 0 HC Counter Timer
16 65 2754084 0 0.00% 0.00% 0.00% 0 GraphIt
17 0 32 0 0.00% 0.00% 0.00% 0 Net Input
18 0 1 0 0.00% 0.00% 0.00% 0 Critical Bkgnd
19 28 826252 0 0.00% 0.00% 0.00% 0 Net Background
20 51 275412 0 0.00% 0.00% 0.00% 0 IDB Work
21 1 15 66 0.00% 0.00% 0.00% 0 Logger
22 41 2754073 0 0.00% 0.00% 0.00% 0 TTY Background
23 48 2754134 0 0.00% 0.00% 0.00% 0 Per-Second Jobs
25 0 1 0 0.00% 0.00% 0.00% 0 Transport Port A
26 21 550819 0 0.00% 0.00% 0.00% 0 Compute load avg
27 319831 45903 6967 0.00% 0.01% 0.00% 0 Per-minute Jobs
28 1 183608 0 0.00% 0.00% 0.00% 0 Dot11 Install Mo
29 6334 629456 10 0.00% 0.00% 0.00% 0 sys monitor
30 97907 1924609 50 0.00% 0.00% 0.00% 0 Power Injector m
31 13808 39941824 0 0.00% 0.00% 0.00% 0 Dot11 driver
32 0 2 0 0.00% 0.00% 0.00% 0 Dot11 dumper
33 0 2 0 0.00% 0.00% 0.00% 0 Dot11 driver log
34 20 2754125 0 0.00% 0.00% 0.00% 0 Voice Metrics Ta
35 369 18360875 0 0.00% 0.00% 0.00% 0 SOAP LED Process
36 0 2 0 0.00% 0.00% 0.00% 0 AAA Server
37 0 1 0 0.00% 0.00% 0.00% 0 AAA ACCT Proc
38 0 1 0 0.00% 0.00% 0.00% 0 ACCT Periodic Pr
39 7608 124872 60 0.00% 0.00% 0.00% 0 IP Input
40 0 1 0 0.00% 0.00% 0.00% 0 ICMP event handl
42 0 2 0 0.00% 0.00% 0.00% 0 AAA Dictionary R
43 14 277776 0 0.00% 0.00% 0.00% 0 CDP Protocol
44 18 2754126 0 0.00% 0.00% 0.00% 0 linktest
45 0 2 0 0.00% 0.00% 0.00% 0 Dot11 aaa proces
46 1 45903 0 0.00% 0.00% 0.00% 0 pmkid
47 1 2 500 0.00% 0.00% 0.00% 0 Dot11 Mgmt & Ass
48 0 2 0 0.00% 0.00% 0.00% 0 DOT11 MFP IO
49 26 3298517 0 0.00% 0.00% 0.00% 0 AiroIAPP Protoco
50 0 2 0 0.00% 0.00% 0.00% 0 Triggered events
51 0 2 0 0.00% 0.00% 0.00% 0 Dot11 auth Dot1x
52 0 1 0 0.00% 0.00% 0.00% 0 Dot11 Mac Auth
53 5 550827 0 0.00% 0.00% 0.00% 0 Dot11CACprocess
54 1 2 500 0.00% 0.00% 0.00% 0 Dot1x Mgr Proces
55 0 1 0 0.00% 0.00% 0.00% 0 MAB Framework
56 0 1 0 0.00% 0.00% 0.00% 0 EAP Framework
57 0 1 0 0.00% 0.00% 0.00% 0 EAP Test
58 0 1 0 0.00% 0.00% 0.00% 0 TCP Timer
59 0 1 0 0.00% 0.00% 0.00% 0 TCP Protocols
60 0 1 0 0.00% 0.00% 0.00% 0 Socket Timers
61 0 1 0 0.00% 0.00% 0.00% 0 IP Traceroute
62 1 3 333 0.00% 0.00% 0.00% 0 L2MM
63 0 1 0 0.00% 0.00% 0.00% 0 MRD
64 3 53 56 0.00% 0.00% 0.00% 0 IGMPSN
65 0 9182 0 0.00% 0.00% 0.00% 0 HTTP CORE
66 0 2 0 0.00% 0.00% 0.00% 0 Soap Upgrade fet
67 0 2 0 0.00% 0.00% 0.00% 0 DDP
68 1 137707 0 0.00% 0.00% 0.00% 0 WLCCP MFP AP
69 0 2 0 0.00% 0.00% 0.00% 0 Dot1x Supplicant
70 1 2 500 0.00% 0.00% 0.00% 0 Dot1x Supplicant
71 1 2 500 0.00% 0.00% 0.00% 0 Dot1x Supplicant
72 0 2 0 0.00% 0.00% 0.00% 0 LOCAL AAA
73 0 2 0 0.00% 0.00% 0.00% 0 AAA Cached Serve
74 0 2 0 0.00% 0.00% 0.00% 0 ENABLE AAA
75 0 2 0 0.00% 0.00% 0.00% 0 LINE AAA
76 1 2 500 0.00% 0.00% 0.00% 0 TPLUS
77 0 3 0 0.00% 0.00% 0.00% 0 Crypto WUI
78 0 1 0 0.00% 0.00% 0.00% 0 EM Background Pr
79 0 1 0 0.00% 0.00% 0.00% 0 encrypt proc
80 0 2 0 0.00% 0.00% 0.00% 0 Soap Consoleless
81 6 4 1500 0.00% 0.00% 0.00% 0 Crypto CA
82 0 1 0 0.00% 0.00% 0.00% 0 Crypto PKI-CRL
83 0 1 0 0.00% 0.00% 0.00% 0 Crypto SSL
84 0 1 0 0.00% 0.00% 0.00% 0 crypto engine pr
85 0 2 0 0.00% 0.00% 0.00% 0 AAA SEND STOP EV
86 0 2 0 0.00% 0.00% 0.00% 0 Dot11 LBS Proc
87 0 1 0 0.00% 0.00% 0.00% 0 Syslog Traps
88 0 45904 0 0.00% 0.00% 0.00% 0 Radio Temperatur
89 1 7 142 0.00% 0.00% 0.00% 0 Syslog
92 25 2754129 0 0.00% 0.00% 0.00% 0 DHCP Client
94 4801 364480 13 0.00% 0.00% 0.00% 0 HyBridge Input P
95 56 3077274 0 0.00% 0.00% 0.00% 0 Tbridge Monitor
96 0 2 0 0.00% 0.00% 0.00% 0 Spanning Tree
97 183 5543231 0 0.00% 0.00% 0.00% 0 RAC I/F Conf.
------------------ show process cpu history ------------------
ap 09:02:23 PM Monday Apr 1 2002 UTC
11111 22222
100
90
80
70
60
50
40
30
20
10
0....5....1....1....2....2....3....3....4....4....5....5....6
0 5 0 5 0 5 0 5 0 5 0
CPU% per second (last 60 seconds)
2
100
90
80
70
60
50
40
30
20
10
0....5....1....1....2....2....3....3....4....4....5....5....6
0 5 0 5 0 5 0 5 0 5 0
CPU% per minute (last 60 minutes)
* = maximum CPU% # = average CPU%
100
90
80
70
60
50
40
30
20
10
0....5....1....1....2....2....3....3....4....4....5....5....6....6....7..
0 5 0 5 0 5 0 5 0 5 0 5 0
CPU% per hour (last 72 hours)
* = maximum CPU% # = average CPU%
------------------ show dot11 associations all-client ------------------
------------------ show wlccp ap mobility traffic ------------------
------------------ show wlccp ap mobility forwarding ------------------
------------------ show crypto key mypubkey rsa ------------------
------------------ show inventory ------------------
NAME: "BR1310", DESCR: "Cisco Aironet 1300 Series (IEEE 802.11g) Bridge"
PID: AIR-BR1310G-A-K9 , VID: V04, SN: FTX1220U0G1
------------------ Mempool statistics ------------------
Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
Processor D2CB44 12389564 7066360 5323204 5238084 5256656
I/O 1900000 7340032 4632280 2707752 2707580 2707688
-------------- Top 100 allocator pc summary -----------
Allocator PC Summary for: Processor
PC Total Count Name
0x000FD014 1591200 1768 *Packet Header*
0x0008732C 955488 14 MallocLite
0x001ABE58 710836 93 Process Stack
0x001B1188 393528 6 MallocLite
0x0005AA84 262196 1 Init
0x0030C5A0 170884 17 Flashfs Sector
0x00509580 167236 1 802.11 driver Instance
0x0050A584 159252 1 Init
0x00194E14 98616 6 TW Buckets
0x008469A8 88736 1163 Init
0x00195BEC 85640 2 pak subblock chunk
0x004340C4 77252 1 Spanning Tree Opt Port Block
0x001741BC 69524 91 Process
0x001C0B3C 65588 1 Memory RO RU Chunks
0x001C0C80 65588 1 Memory RO RU Index Chunks
0x001A64A8 65588 1 CPU RO RU Chunks
0x0011AB34 65588 1 Buffer RO RU Chunks
0x0011AB5C 65588 1 Buffer RU Notify Chunks
0x0011A844 65588 1 Buffer Display Chunks
0x0009DF8C 65588 1 Parseinfo Blocks
0x001369EC 65588 1 IDB List Element Chunks
0x0052ABEC 65588 1 dot11drvr clients
0x005491E0 65588 1 Dot11 Pmkid Record Chunks
0x005593D8 65588 1 Dot11 Mgmt Station Chunk
0x000133FC 65588 1 AAA DB Chunk
0x0017C11C 62936 228 Init
0x0048AEBC 60076 1 BTE Entries
0x0008F544 49628 3 Init
0x000DBC6C 49204 1 Exec
0x001814A8 40104 2 RMI-RO_RU Chun
0x000F5044 32824 1 Init
0x0009E004 32820 1 Parse Nodes
0x00509FD8 32820 1 dot11 call control events data
0x0055BA1C 32820 1 Dot11 Mgmt SSID Chunk
0x0055BA54 32820 1 Dot11 Mgmt SSID Config. Chunk
0x00029314 32820 1 AAA SG ID table
0x005D2F24 26716 2 dot11 auth client chunk
0x00099500 26452 1 PM Event Pool
0x0007D868 26424 6 TTY data
0x001916C4 21364 7 Keepalive
0x001C19B8 20052 1 Managed Chunk Queue Elements
0x0017FD08 20052 1 RMI-RO_RU Chunks
0x0017FD30 20052 1 RMI-RO_RG Chunks
0x0017FE4C 20052 1 RMI-RU Chunks
0x005B2244 20052 1 wlan_ip_mcast_record
0x005B2D04 20052 1 wgb_ip_mcast_record
0x000A35CC 19748 258 Parser Linkage
0x000E79AC 19732 1 Init
0x00177088 17984 91 Process Events
0x001063FC 14860 5 *Hardware IDB*
0x0030C4BC 11704 154 soap_flash init
0x007BF4D4 11676 1 DISC specific structure members
0x000E7A2C 10776 86 Init
0x0036DA6C 10432 2 dhcpc_lq_chunk
0x0017BCD0 10260 5 Reg Function 1
0x0016DDDC 10052 1 List Elements
0x00179694 10052 1 Watched Queue
0x001796BC 10052 1 Watched Boolean
0x001796E4 10052 1 Watched Bitfield
0x0017FEB4 10052 1 RMI-RG Chunks
0x0016C940 10052 1 List Elements
0x00103018 10052 1 Packet Elements Cache
0x00103044 10052 1 Packet Elements
0x002C689C 10052 1 Pathents for parsing
0x002C68C4 10052 1 TTY Pathents for parsing
0x00311B84 10052 1 Flashfs Sector Pointers
0x0030B668 10052 1 Flashfs Sector
0x0052AC7C 10052 1 dot11 cc info
0x0015480C 10052 1 AAA chunk
0x001C1D28 10052 1 List Elements
0x005B14F0 10052 1 wlan_ip_mcast_host
0x005B152C 10052 1 wlan_ip_mcast_domain
0x002A5390 10052 1 IPTRACE probe chunks
0x003C00C4 10052 1 SNMP SMALL CHUNK
0x003C010C 10052 1 SNMP MEDIUM CHUNK
0x002BE794 10052 1 Time Range Entry Chunks
0x000E700C 10052 1 Init
0x000E7044 10052 1 Init
0x005D7728 10052 1 DDP UDP tx Chunk
0x00361E40 9652 1 NET ACCT LISTS
0x00361E7C 9652 1 SYS ACCT LISTS
0x0003964C 8852 1 PPP ACC LISTS
0x00799E10 8448 88 *Init*
0x0017BC3C 8208 4 Reg Function 1
0x0088D140 8128 1 Crypto Engine Object Table
0x0007C064 8080 102 NameDB String
0x00039688 8052 1 NET AUTHOR LISTS
0x000A4240 7668 71 Parser Mode
0x005510A0 7312 1 Dot11 Mgmt Client Send Fail Event Chunk
0x005510D8 7312 1 Dot11 Mgmt Client Not Found Event Chunk
0x00106418 6700 5 *Software IDB*
0x0039DEC0 6488 1 Init
0x00705468 6300 3 Init
0x007054B4 6300 3 Init
0x007054E8 6300 3 Init
0x000A42CC 5444 71 Parser Mode Q2
0x000A42A8 5404 71 Parser Mode Q1
0x000A6C2C 5368 10 Chain Cache No
0x0016DE18 5052 1 List Headers
0x00179734 5052 1 Watcher Info
Allocator PC Summary for: I/O
PC Total Count Name
0x000FD064 4628876 1767 *Packet Data*
0x007B8DD0 2056 1 Init
0x007BA3BC 896 4 Init
0x005C1480 296 2 Init
------------------ show region ------------------
Region Manager:
Start End Size(b) Class Media Name
0x00000000 0x018FD7FF 26204160 Local R/W main
0x00003000 0x0089B823 9013284 IText R/W main:text
0x0089B840 0x00B8E17F 3090752 IData R/W main:data
0x00B8E180 0x00D2CB3F 1698240 IBss R/W main:bss
0x00D2CB44 0x018FD7FF 12389564 Local R/W main:heap
0x01900000 0x01FFFFFF 7340032 Iomem R/W iomem
Free Region Manager:
Start End Size(b) Class Media Name
------------------ show buffers ------------------
Buffer elements:
1119 in free list (1119 max allowed)
849266 hits, 0 misses, 619 created
Publi -
Windows no longer detecting my Audigy 4?(Non-P
Hey all. I've had my Audigy 4 (non-Pro) installed and working super for about 50 days, but it started giving me a weird problem. Windows was no longer detecting the card! It was weird. DX Diag, programs like EVEREST... they all report no sound card whatsoever.
Here are my PC specs:
XP Home Edition
Albatron K8X800 Pro
S754 3200+ ClawHammer
x 2 OCZ ELPE 52 MB(2-3-2-5)
Visiontek XTASY X850XT PE
x 80 GB SATA 2 Seagate, x 80 GB Maxtor
Some other things to note:
XP has been repaired. Went from Service Pack , updates, and all the way to Service Pack 2. The card requires XP w/SP2, yes, so I have that covered.
Onboard audio is disabled through the bios. I have AC'97 integrated audio on this.
My motherboard has fi've PCI slots - although I can only access 4 because my video card is in the way, and I have tried three of those and I get the same problem.
I have tried it in other PCs in my house, double-checked each time - so it is not ESD as I originally believed. It works just fine on those PCs. It is being not located only on MY PC.
So guys and gals, I do not know what to do... I am stumped. It's the weekend so I can't call Creative support until Monday. I don't want to request an RMA through my warranty because clearly it's just a problem with my PC. What should I do?!Message Edited by Celsius on -26-2005 07:36 PMDevice not recognized in iTunes
-
IPod Touch/Phone 4gens No Longer Detected in WINDOWS MY COMPUTER but OK in iTunes
Since I have not found help online regarding the above situation I'm looking for help accordingly. For most folks it's iTunes not detecting i-Devices, but my situation is unique.
It started last night after I was on the phone for hours with Norton regarding error messages I was getting with Internet Security. Those issues have been resolved.
Again: iTunes detects and interacts successfully with ALL my iDevices. Windows Vista > My Computer no longer does.
Please help.Just now I performed the following:
Turned off and turned back on AMDS(Apple Mobile Device) Service.
Disabled Norton Internet Security, and tried checking if Windows would see my devices.
For anyone who has Windows Vista you are familiar with the notes that play when you plug in a USB device: "da-dunk!" Low-High note dadunk indicates connected. High-low indicates it was disconnected.
I can tell there is a problem because right after the Low-High dadunk in Vista I get a triple Low-note Du-du-dunk.
Please help! -
Not detecting tv display when connected with Apple Mini-DVI to Video Adapte
I am connecting my macbook to my older tv using a Apple Mini-DVI to Video Adapter to an RCA (yellow video prong) and then into the tv. The red and white audio prongs hang loose, not hooked into anything on both ends. When I go into Displays there is no option for mirroring displays. I hit 'detect displays' but nothing happens. The Apple Mini-DVI to Video Adapter is brand new, just ordered it from apple. And I use the RCA cord all the time with other machines into my tv and it works fine.
Any help is really appreciated. Thanks!Which generation MacBook do you have because at some point Apple dropped support for that adapter. Here is a link to a list of Apple adapters and compatible computer models:
http://support.apple.com/kb/HT3235 -
No TV detected using mini-DVI to S-VHS/Scart
In my old laptop, I have used the S-VHS output from the graphics card, and in order to see the monitor on my TV, I had to set the TV as default monitor. Now I recently purchased an iMac with a mini-DVI to video. I put my s-vhs cable into this adapter and at the other end I put the s-vhs cable into a scart adapter and then into the tv. When I push "Detect displays"-button, I see a short flicker (grey lines) on my TV and then it becomes black again. I have tried all possible resolutions, but I have a feeling that the TV is not properly detected. I have also tried all possible codecs like NTSC, PAL and SECAM on my TV ++, but it doesn't work?! I'm a total newbie, so hopefully there is a simple solution:) - maybe some settings on the iMac?
Okay you should connect your dvi to S-video and then the other end of the S-video small round 7 pin connector to the S-video port on your TV.
Then set your tv channel to input or video in sometimes listed as L1 or aux in.
Once this is set to same as what you would connect a DVD or VHS via rca round pin red/yellow/black or white cables to the channel / input then press detect.
The screen should go black and then after say 5+ secs. you should see a colorfull / background or something on the tv and on your Apple and it will also show the resolution settings for each screen on that screen itself.
Then you can choose either to mirror the screens = same size display and desktop on both or each one to be independent.
Maybe set your tv then to 800x600 to be safe and select what ever tv standard is available in your country. (ntsc/PAL)
PS: the S-video looks like the old PS2 mouse connectors from windows PC's from before usb was discovered. -
Is there a way to detect two keys at the same time?
Is there a way to detect the keys if the user is holding two keys down at the same time?
yes, but you'll have to check outside of the event loop (i.e. don't check for it in the keyPressed method).
just use an array of keys that keeps track of which keys are currently down and which are up. you could use a boolean array but I use an int array because... Im not sure I've just done it probably because of my C background. anyway, basic setup:
import javax.swing.*;
import java.awt.*;
import java.awt.event.*;
import java.util.*;
public class MultiKey extends JFrame {
int keys[];
public MultiKey() {
super();
keys = new int[256];
Arrays.fill(keys,0); // 0 = key is up
enableEvents(AWTEvent.KEY_EVENT_MASK);
show();
public void processKeyEvent(KeyEvent e) {
// the 0xff below binds the key code to below 256
int key = (e.getKeyCode()&0xff);
if (e.getID() == KeyEvent.KEY_PRESSED) {
keys[key] = 1; // 1 = key is down
else if (e.getID() == KeyEvent.KEY_RELEASED) {
keys[key] = 0; // 0 = key is up
protected boolean isKeyDown(int key) {
return (keys[key] != 0);
protected boolean isKeyUp(int key) {
return (keys[key] == 0);
}so now at any time in your code you can check key state by using the isKeyUp and isKeyDown methods. this is about as close as you get to input polling in java unless you use LWJGL or something similiar ;)
you can try out a full executable example at my site here - just open up the jar and start holding keys down :) -
IPod Touch, not detected in Windows or iTunes...
First of all, hello to everyone...
i want to say that i read a lot EVERYWHERE about my issue and still i couldnt find a solution...
the problem is easy, i have a 3rd gen ipod touch, OS 4.2.1 now fully working... but, it's not detected in windows or itunes, as simple as that, and as u all have read in lots of other posts...
my ipod is now working because i took it to an apple store and they charged it in a MAC and they had no problem at all. the MAC detected the ipod, with all its content and my ipod's name...
but when i took it home -this has been hapenning since maybe... 5 MONTHS!-, i plug it in my PC and nothing happens...
ok, first of all, my spec... win vista home premium 64 bits, last version of itunes...
i tried ALL the solutions provided in APPLE official support page, and nothing happens... that means:
1- completely uninstall itunes and then reinstalling it... i ALSO FORMATED my entire hard drive twice!!!!
2- tried all USB ports and even an entirely different PC and nothing happened
3- bought 3 different IPOD to USB cables and nothing happened
4- tried setting ipod to restore, that way itunes SOMETIMES detected the ipod but i coulnt restore because of different error codes, so i had to take it several times to apple store to "unblock" it...
the only way it works -detection and charge- is with MAC computers or dock systems such as an iHome my gf has thats the way im charging it now, but otherwise it wont work...
i would really appreciate any help, since idont know what else to do!!
thx in advance!!HI I was having some other problems getting my itouch to restore because it was not being recognized in itunes and kept erroring out. Now it has finally restored after I updated all kinds of drivers and removed and reinstalled itunes and apple software a million times,(yes this is all after installing itunes 8.1 and paying for an itouch upgrade as well) Now itunes says it cannot do anything with the ipod because it is getting an invalid response from the device. So it won't put anything back on my itouch or even show that I have plugged it in. I emailed tech support, If I find anything out I'll let you know, will you do the same for me?
-
IPod Nano 4Gb (2nd Gen) not detected by Windows or iTunes
I am hoping someone can help me with this as I am at my wits end.
When I plug my iPod into the usb port, it begins the charging process, but neither windows, nor iTunes will detect any new devices. I have tried the 4 R's (the fifth needs a connection with iTunes), putting it into disc mode, and even on 3 different windows computers, but no dice. To save the no doubt normal questions, The usb ports are 2.0, and brand spanking new, which i have tested sucessfully with other usb devices, so I know it's not the usb port. I have the latest drivers & updates installed, and the latest version of iTunes also installed.
Other potentially useful info:
The model is iPod nano 4bg alu 2nd gen
It's not new, i was given it as a gift by a friend who upgraded to the video model.
Though I can't be sure, I suspect that the dock cable isn't an apple product. Given that *very few* places where I live sell official iPod accessories, it is difficult for me to check.
Like I said, i really hope someone can help me, I really don't know how long i can go listening to my friends rather dubious music tastes...hi,
try the following article my friend...it will definitely resolve your problem..
http://docs.info.apple.com/article.html?artnum=302420
http://docs.info.apple.com/article.html?artnum=61711
Regards,
Sam -
Error message "iTunes has detected an iPod that appears to be corrupted"
Everything used to work just fine until recently. On my Windows XP Home SP3 laptop, with iTunes (version 9.0.2.25) already open, I connect my 5th Generation iPod Nano and get the following message in iTunes:
"iTunes has detected an iPod that appears to be corrupted. You may need to restore this iPod before it can be used with iTunes. You may also try disconnecting and reconnecting the iPod."
If I plug the iPod into the computer without first starting iTunes, the Windows ‘Auto Play’ message comes up immediately then disappears and then the following message appears:
"Your iPod needs to be formatted for use with Windows. Would you like to run iTunes to restore your iPod Now?"
Otherwise, the iPod functions normally when not connected in iTunes. I can play the music, videos, and record videos with no problems.
The troubleshooting steps I took were:
I performed a reset of the Nano by first sliding the hold switch on/off a few cycles, leaving switch off (no orange showing), then pressed and held the Menu + Select button until the Apple logo appeared. Then I tried it in iTunes again; no such luck, same error. I then did a reset again, this time with the iPod connected to an AC power source; still no luck. I tried the reset numerous times and it didn’t help.
Next, I ran the diagnostics by pressing and holding the Menu + Select buttons immediately followed by the Select + Reverse buttons. I stepped through all the diagnostics tests and all tests passed as far as I could tell (there was no errors reported).
After this, I tried it in iTunes again and still no luck.
I even tried the iPod on my Windows Vista Home Premium (32 bit) machine and it behaved the same way. The version of iTunes on that machine was at an earlier version when I first tried it there. I then upgraded iTunes to the latest version but that didn’t help either.
I can sync my iPod Touch and 2nd gen Nano without any problems.
Sorry about be long winded about this but I am wondering if anyone else may have other suggestions. I want to try and avoid a restore if possible because I have some videos I recorded that I would like to get off the iPod. I’m not concerned about my music files as I have them always backed up but didn’t get the videos off yet.I am having this same problem with my brand new Mac Pro. It seems to be tied to the computer awaking from sleep (no I am not leaving the iPod connected while sleep... I am referring to waking the computer from sleep and then connecting iPod as opposed to restarting the computer and then connecting the iPod). In other words, if you are getting this error message, try ejecting the iPod, restart your computer, then connect the iPod and see if the error message goes away. For me it does, but I only get one shot at it, if I eject the iPod and then reconnect it, the error message returns. This happens on both iPods I have. I have rebooted (hold menu-select) and gone to disc mode (hold select-play) and the error message remains. The only way it goes away is to reboot the computer, then I get one shot at hooking up an iPod.
I NEVER had nor get this error message when I connect to the Windows PC that I started with. Perhaps the iPod does not like moving from PC to Mac? -
My Ellipsis 8 can no longer detect my gym's wifi signal. Please help!
I used my Ellipsis 8 to watch Netflix over the open wifi signal at my gym for 2 months with no problem. One day I showed up and no signal was found. I went through all the trouble shooting steps all the way down to factory resets with no resolution. Called Verizon tech support and still nothing. They had me send them the tablet in a recovery box. One week later I have the tablet back and they said nothing was wrong with the unit. I went to the gym today and it still can not detect the signal. My Samsung phone picks up a very strong signal. No other people have reported a problem with wifi connection issues. Obviously Planet Fitness will not allow me to start messing with their router. Any suggestions would be GREATLY APPRECIATED!
I understand the importance of ensuring you are able to get connected to wifi michaeltatham. Allow us to get to the bottom of your tablet concerns. Have you recently installed any new software or new applications when it stopped connecting to the gym wifi? Have you tried to connect another device to your gym wifi?
Thank You,
MichelleS_VZW
Follow us on Twitter @VZWSupport
If my response answered your question please click the �Correct Answer� button under my response. This ensures others can benefit from our conversation. Thanks in advance for your help with this!! -
I cannot access or reinstall Itunes, and my ipod isn't being detected
So, sometime after the fall of 2010, which I suspect was after iTunes 10 was launched, I noticed I couldn't access iTunes.
It read error 2330.
I did some sleuthing for months, and now I get these error messages under the heading "iTunes + Quicktime" when I attempted a re-installation of iTunes:
"There's a problem with this Windows Installer package. A program required for this install to complete could not be run. Contact your support personnel or package vendor"
"An error occurred while attempting to create the directory: C:\Documents and Settings\All Users\Application Data\Apple Computer\iTunes"
In the past while attempting to re-install iTunes, I got error message 2330...STILL don't fully know what this means.
I currently have Bonjour, the iTunes folder, The iPhone Configuration Utility folder, and Quicktime on my desktop...The actual programs are also in my C:\ drive in Program Files...I can also see Apple software in the Add/Remove Programs section of the Control Panel on my PC.
I seem to be able to access iTunes/iTunes store via the executable file in the iTunes folder by clicking "iTunes.exe", but no other way...I also noticed that the software will run normally, but not detect my iPod or allow my computer access...So in other words, iTunes doesn't recognize my computer as being authorized for my account, and yet it displays my email address in the upper-right hand corner of iTunes.
It's like I can only access a "half version" of the full iTunes I once had by going through that folder...No clue what's happening or what files may be missing or corrupted.
Quite simply put, I need help...I want to be able to use iTunes and my iPod Touch (1st gen) like I was able to this past fall before the mysterious accident or corrupt files ruined everything.For that 2330 error, run chkdsk on your C drive.
How to perform disk error checking in Windows XP
http://support.microsoft.com/?kbid=315265 -
This appears to be a software issue: my iPad 3G (32GB) is not detected by iTunes (yet my iPhone is), nor by Windows Vista. Furthermore, it does not charge from the wall charger until it shuts down in low battery, and only charges to 2%, after which it switches on again. Tried switching off and charging, which only causes it to switch back on again. Also tried cold resetting, but problem persists. Was working fine previously, no updates, additions or subtractions were made to either PC OS, iPad or iTunes immediately before problem started... and there doesn't seem to be any mention of this on the internets (including this forum). Any suggestions?
Soft boot, hold down top button and middle bottom button at the same time, with the iPhone connected to your computer and iTunes will recognize the phone on reboot.
-
Iphone is no longer detected on itunes/computer it is synched with.
One of my Iphones is no longer detected by the itunes/computer that it is synched with. The computer/itunes does detect other devices. The iphone in question is able to be detected on another computer/itunes.
I updated software oof iphone on another computer. I updated itunes on the computer that does not detect the phone. I rebooted both. I tried software conflict.
Does anyone have an idea how to resolve? I have all of my contacts, apps, photos, music etc on that computer.
When I updated phone software on another computer to see if that was the problem it wiped out all music,apps, photos etc on the phone. I have thee devices with one apple id and they are synched to different computers.You should try another USB cable, charging and sending data through the cable is not completely the same, sending data is using other contacts inside the plug or docking connector.
Maybe you are looking for
-
Report Issue - A subquery filter may not reference the current report
Hi, I a, trying to create a drill down report - I am getting below error when I drill down from summary report to detail - A subquery filter may not reference the current report (or contain a circular reference to any report). Error Details Error Cod
-
I have a 64-bit Windows 7 PC and a much-loved 2008 iPod Classic 120Gb. I recently updated iTunes to V12.1. I no longer have the 'info' legend in 'settings' and am unable now to update my calendar and contacts. Help!
-
Self-assigned ip address -- can't connect to Airport
I have a 2006 MacBook Pro which recently started exhibiting the exact same behaviour as reported by another poster in 2011: For some reason the computer has started self-asigning its IP address and Network Preferences says that, because of the self-a
-
I just spoke to Apple rep about the Prepared To Ship
Even if your phone does not say prepared to ship but your Delivery say Delivered June 24, you are getting your phone June 24. ABSOLUTELY GETTING IT THAT DAY! Your status will update when it ships even if they expedite your shipping. I only asked abou
-
How do i delete imovie videos and still have them on my time capsule
how can i delete imovie videos and still have them on my timecapsule