Jawbone2: Must choose Jawbone from Audio Source for Incoming Calls

Had the original Jawbone and just got the new Jawbone. Love it except I must choose Audio Source>Jawbone for all incoming calls. All I had to do with the original Jawbone was 'slide to answer'.
I did unpair the headset, turned off Bluetooth and did reset the Jawbone but re-pairing the headset.
Any ideas?

I have the same problem. I emailed customer support at Jawbone and this is the response I got back from them. So I followed the instructions but I had little hope. I did it 2x. No help.
Response (Chris) - 06/12/2008 10:57 AM
Hi Ross,
I understand your problem and have a fix for it. I have experienced the same problem. To fix this reset the Jawbone and iPhone and then repair them. Also make sure that if this happens again that you use the headset because the New Jawbone has an idle feature that goes in to effect after 15 minutes.
Sincerely,
Chris
The Jawbone Support Team
www.jawbone.com
Customer (ross brookshire) - 06/10/2008 11:36 AM
So I had an original Jawbone and didn't have this problem on my iphone. Thank god you guys made a magsafe type connector for the power cord.
Anyways, when I receive a phone call on my
iphone if I use my phone to accept the call, the phone answers and says that it is using the headset. But I can't hear anything. But if I put the phone up to my ear I can hear the conversation. So then I have to go to the audio source on the iphone and change it to headset.
But if I answer it using the jawbone button it works fine. I know the answer is to just use the headphone. But I didn't have to with the old one. What else can be done.
Thanks for the help.
RBB

Similar Messages

My iphone 4S has problem in making and receiving the calls. While making the call , call fails and netwrok disappears. Like wise no voice is heard for incoming calls. This happened after return from the overseas travel.

My iphone 4S has problem in making and receiving the calls. While making the call , call fails and netwrok disappears. Like wise no voice is heard for incoming calls. This happened after return from the overseas travel.

Hello SamSax
Check out the assist page below for troubleshooting call connectivity.
Calls and connection issues
http://www.apple.com/support/iphone/assistant/calls/
Thanks for using Apple Support Communities.
Regards,
-Norm G.

My new iPhone 5S will not ring for incoming calls. It vibrates. I've tried suggested tips for iPhone 4 but it doesn't work for 5S. Please help!!

Can anyone help. My new iPhone 5S does not ring for incoming calls. It vibrates. How can I get ringer to work?

Hello lyngos,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iPhone: No sound or distorted sound from speaker
http://support.apple.com/kb/TS2802
If an audio issue occurs when using a specific application, try testing other applications to see if the issue persists.
If the iPhone is paired with a Bluetooth headset or car kit:
Try turning off Bluetooth.
If you experience difficulties with the Bluetooth feature, follow these troubleshooting steps.
Restart the iPhone.
If restarting doesn't fix the issue, ensure that your iPhone is updated to the latest version of iOS.
Best of luck,
Mario

I have no volume for incoming calls ,texts and emails how do i fix it

I have no volume alert for incoming calls ,texts and emails . How can I fix this as I can watch video clips wiyh sound

Hello Strangers1,
After reviewing your post, I have located an article that can help in this situation. It contains a number of troubleshooting steps and helpful advice concerning audio issues:
iPhone: No sound or distorted sound from speaker
http://support.apple.com/kb/ts5180
Verify that the volume is set to a level you would normally be able to hear.
Ensure that there is nothing plugged in to the headset jack or the dock connector.
If the iPhone is in a protective case, make sure that the speaker port isn't blocked by the case.
Make sure that the speaker and dock port aren't clogged with debris. If necessary, clean it with a clean, small, dry, soft-bristled brush. Carefully and gently brush away any debris.
If an audio issue occurs when using a specific application, try testing other applications to see if the issue persists.
If the iPhone is paired with a Bluetooth headset or car kit:
Try turning off Bluetooth.
If you experience difficulties with the Bluetooth feature, follow these troubleshooting steps.
Restart the iPhone.
If restarting doesn't fix the issue, ensure that your iPhone is updated to the latest version of iOS.
If the issue is not resolved, please contact Apple Support.
Learn more about troubleshooting iPhone hardware issues.
Thank you for contributing to Apple Support Communities.
Cheers,
BobbyD

How can I turn off the phone saying "Call from" #/name when getting incoming call.

How can I turn off the phone saying "Call from" #/name when getting incoming call before the ring tone starts? I have a LG accolade

I recommend checking your prompts and alerts to turn this feature off. This may be you "Call Connect" or "Readout" alerts. Listed below are steps to update this feature.
With the flip open, press the Voice Command Key (on the left side of the phone).The Voice Commands feature has several settings which allow you to customize how you want to use it. Access Voice Commands, then press the Right Soft Key[Settings]. Your choices are below:
-Confirm Choices--- Automatic/Always Confirm/ Never Confirm
-Sensitivity--- Control the sensitivity as More Sensitive/ Automatic/Less Sensitive
-Adapt Voice ---If the phone often asks you to repeat voice command,train the phone to recognize your voice patterns.Train Words/ Train Digits
Prompts ---Mode/ Audio Playback/Timeout
* For Mode, set Prompts/ Readout+ Alerts/ Readout/ Tones Only.
* For Audio Playback, set Speakerphone or Earpiece.
* For Timeout, set 5 seconds or 10seconds.

My phone displays numbers instead of contact names for incoming calls and text - how do I fix?

My phone displays numbers instead of contact names for incoming calls and text - how do I fix? It used to display the names if there was a contact listed, now it just shows numbers regardless of whether or not the number corresponds to a contact name in the contact list. Can anyone help? I googled this problem and lots of folks have experienced it, however there is not a consensus for a resolution.

Alexandribill, I have been having the exact same issue. I got a new phone and restored my contacts. If the # doesn't have the area code first then the name isn't shown. I just added my husbands area code to my phone and called my phone from his and now his name shows up...Ugh, I have to go through and manually add the area code to all my contacts....
I'd say Verizon needs to rewrite their program to include the area code in the restoring from backup process!

Ringer doesn't work for incoming calls

My iPhone 4 ringer won't work for incoming calls. It is not on vibrate only and the ringer works through the earphones when earphones are connected. Any suggestions?

Thank you so very much.
. Simple yet perplexing.. I bought the waterproof case and had them put it on before leaving the store.. GRANTED, I never read the instructions.. Just knew it must have been something in the way I programmed the phone. I especially loved that you put up an illustration with your explanation.
Mahalo,
Donna Jo

Callerid for incoming call

I have configured some clients number as CCM users so that we can easily find and call them from the Corporate Directory. Is it possible for these clients names to show up in the phone for incoming calls (from PSTN)?Some kind of lookup in LDAP...
I use CCM 4.2
Darek

The callerinfo service from the SDK should help you get started. Unfortunately, adding users in ccm only populates the directory - the info shown on the display when making calls is taken from the lines, and I have no clue how ccm would react if you created dummy phones with dummy lines that have the proper number.. the name would probably still not be displayed since the call doesn't come from the line in question but a PSTN trunk.

HT1413 how to set the ringer to flash the camera flash for incoming calls

I have seen other iphone 4 have their riinger set up to flash the camera flash for incoming calls. I have not been successful to figure it out from the settings feature. does anyone know how to do this?

Hi jdflo50,
The feature you are talking about was introduced in iOS 5 Software Update v1.0:
http://support.apple.com/kb/DL1456
Accessibility improvements
Option to light LED flash on incoming calls and alerts for iPhone 4S and iPhone 4
Settings > General > Assessibility > LED Flash for Alerts
Hope this helps!
- Judy

When will apple bring back the onscreen cancel button for incoming calls?

when will apple bring back the onscreen cancel button for incoming calls?

No one here would know, as there is no one from Apple here. Suggest such to Apple using this:
http://www.apple.com/feedback/iphone.html

Bluetooth no longer works for incoming calls after recent update

When I updated my Bluetooth to iOS 6, the Bluetooth no longer works for incoming calls. I press button to answer call, it makes a small cracking noise, and then sends the call to my phone. I can use the Bluetooth for outgoing calls and it works just fine. I was hoping when I updated to iOS 6.0.1 that the problem would be fixed. I have uninstalled and reinstalled Bluetooth but that has not helped either. I am frustrated. I have a LG HBM-905 Bluetooth that I loved prior to this problem.

Magically started working today after I synced.
Post relates to: Treo 700w (Verizon)

TS2634 My iPhone 4s does not ring for incoming calls. Ring tone is set/settings/sound. It used to ring. I think it has to do with updating to IOS 7.0.4? After updating IOS 7.0.3 my microphone stopped working. Had to clear/reload.

My iPhone 4s does not ring for incoming calls. Ring tone set and used to ring. I think it has something to do with updating the IOS 7.0.4. When I updated to 7.0.3 the microphone stopped working. Had to call Apple Support and cleared phone and reloaded. ($57 charge). Any suggestions?

Start with your finger at the bottom of the screen (about even with the home button) and swipe in an upward motion. There should be a row of icons at the top of a grey field. if the quarter-moon icon is bright white, tap it. If it was (and still is) dark, take the iPhone in to be evaluated by a qualified technician.

2960X 15.02(EX5) %AAA-3-ACCT_LOW_MEM_UID_FAIL:AAA unable to create UID for incoming calls due to insufficient processor memory.

Deployed four 2960X switches in a stack. All okay for about one month then tried to web browse for the first time via firefox which partially displayed the page. I assumed this was a browser error. So tried Chrome then IE which both failed. Chrome was a bad display and IE fails to connect.
After this, I could not telnet or ssh. Plugged into the console and immediately started receiving:
%AAA-3-ACCT_LOW_MEM_UID_FAIL: AAA unable to create UID for incoming calls due to insufficient processor memory
%% Low on memory; try again later
I am unable to log in. I have a TAC case logged but the first step to try is a reboot which will be difficult until I can get a maintenance window. When I do get a maintenance window, I would also like to deploy a fix such as a different version of code or a work-around cofig command. I don't mind disabling HTTP.
Any suggestions?

I am currently working with TAC
The switches failed about 18 hours later and had to be rebooted to get back up. Now that I have console/telnet access, I can see the memory being depleted mostly by the Auth Manager process at about the same rate as free memory is dropping.
SW13#sho proc mem sort | i Auth Manager
191   0 177721332   95004616   34757416          0          0 Auth Manager
SW13#sho proc mem sort | i Auth Manager
191   0 177754888   95025696   34759780          0          0 Auth Manager
SW13#sho proc mem sort | i Auth Manager
191   0 177774316   95037928   34761056          0          0 Auth Manager
SW13#sho proc mem sort | i Auth Manager
191   0 177799720   95053940   34762888          0          0 Auth Manager
SW13#sho proc mem sort | i Auth Manager
191   0 177824976   95069732   34764696          0          0 Auth Manager
SW13#
SW13#
SW13#sho proc mem sort | i Processor
Processor Pool Total: 442796836 Used: 103448576 Free: 339348260
SW13#sho proc mem sort | i Processor
Processor Pool Total: 442796836 Used: 103454416 Free: 339342420
SW13#sho proc mem sort | i Processor
Processor Pool Total: 442796836 Used: 103455860 Free: 339340976
SW13#sho proc mem sort | i Processor
Processor Pool Total: 442796836 Used: 103459236 Free: 339337600
SW13#sho proc mem sort | i Processor
Processor Pool Total: 442796836 Used: 103461040 Free: 339335796

Please help ... have new samsung ativ se windows 8 phone ... screen lock is on to require password, but on incoming calls its not locked ... how do i lock it for incoming calls too ???? thanks

please help ... have new samsung ativ se windows 8 phone ... screen lock is on to require password, but on incoming calls its not locked ... how do i lock it for incoming calls too ???? thanks

Personal rant, why do people write the entire problem in topic line
It's not possible with Windows Phone 8. What's the point, a call is coming in and the phone allows you to answer.

How can I get volume on my I6 to hear incoming calls . I went to setting , sounds, and selected a tone, but still no sound for incoming calls, texts, or other notifications.

How can I get volume on my I6 to hear incoming calls . I went to setting , sounds, and selected a tone, but still no sound for incoming calls, texts, or other notifications.

Hi rsample,
Thank you for visiting Apple Support Communities.
Your symptoms make it sound like the iPhone side switch is set to silent mode.
iOS: Understanding sounds, ringtones, and alerts
Set your device to silent mode
iPhone: Toggle the Ring/Silent switch on the side of the device.
Best Regards,
Nubz

Jawbone2: Must choose Jawbone from Audio Source for Incoming Calls

Similar Messages

Maybe you are looking for