JMS, MQ WebSphere messagesplit and commit scope

Dear all
I have a problem regarding read/write to WebSphere MQ.
I'm sending messages from ERP to XI to MQ Websphere. There is a twist on my scenario. When XI receive a message from ERP XI creates 3 messages: Begin, Data and End. This is because the receiving application needs these. The problem arises (the MQ guys thinks) when i write to the qeue at the same time the legacy system gets from it. Sometimes the legacy system reads the begin message only because its the only one in the queue - next time he reads the system crashes because of the missing begin.
Is there some way to make the three messages part of the samme commit scope in MQ so the legacy always get at chunk of messages.
The message split is done via messagemapping without BPM - BPM not allowed in our landscape.
Any suggestions?
Kind regards
Martin

Hi ViJaYaNt JhA
I find it difficult to relate your answer to my question. I have actually seen this response before in
Message "Lost" in a JMS adapter. which is regarding af sender JMS adapter. My case is receiver and I'm not having diffuculties about unique msgID. Can you go into details about this?
Kind regards
Martin

Similar Messages

Configuration for JMS Adapter Sensor action and JMS Queue sensor action..!!

Hi,
Id like my BPEL process to send an XML message to JMS on Websphere,I was able to do this through a JMS adapter.But I would more like to add sensors into my process which would really do the same thing - send an XML message to JMS Q.
Now I understand that there are two ways to do this,JMS Queue and JMS Adapter - thorugh bpel sensor action.
I am able to use JMS Queue and it works fine , but adds its own xml tags to the message,Is there any way I could send only my xml payload as a message to the queue??
Also could any1 tell me what is the configuration for JMS Adapter sensor action?
Any suggestions how do I go about it??

Hey Anirudh,
Thanx for the response :-)
All these hold good when I have an AQ adaptor right,But the thing is I want to send a message to a 'JMS' queue with out actually using an adapter configuration wizard and everythng..So I resolved to JMS queue Sensor action..Heres the xml snippet from the sensorAction.xml files which is generated..
<actions targetNamespace="http://xmlns.oracle.com/Test_JMS_Logging" xmlns="http://xmlns.oracle.com/bpel/sensor" xmlns:tns="http://xmlns.oracle.com/Test_JMS_Logging" xmlns:pc="http://xmlns.oracle.com/bpel/sensor">
<action name="JMS_LogEntry" publishName="" publishType="JMSQueue" enabled="true" filter="" publishTarget="jms/L_Queue">
<property name="JMSConnectionFactory">jms/L_QueueCF</property>
<sensorName>ActivitySensor_JMS</sensorName>
</action>
</actions>
This works grt and adds messages to the queue..But adds its own header info according to the sensor.xsd loacted at the Oracle_home\bpel\system\xmllib\ folder.
Right now the XML message added to the Queue is:-
<actionData xmlns="http://xmlns.oracle.com/bpel/sensor">
<header>
<sensor sensorName="ActivitySensor_JMS" classname="oracle.tip.pc.services.reports.dca.agents.BpelActivitySensorAgent" kind="activity" target="AddLEntr
y" xmlns:pc="http://xmlns.oracle.com/bpel/sensor" xmlns:ns2="http://www.ulrhome.com/2008/10/L_Entry" xmlns:tns="http://xmlns.oracle.com/Test_JMS">
<activityConfig evalTime="completion">
<variable outputDataType="string" outputNamespace="http://www.w3.org/2001/XMLSchema" target="$WriteL_Produce_Message_InputVariable/L_Entry/ns2:L_Entry/ns2:LCName"/>
</activityConfig>
</sensor>
<instanceId>950016</instanceId>
<processName>Test_JMS</processName>
<processRevision>v2009_04_15__40833</processRevision>
<domain>default</domain>
<timestamp>2009-04-15T11:21:23.596-04:00</timestamp>
<midTierInstance>app01.ulrhome.com:9700</midTierInstance>
</header>
<payload>
<activityData>
<activityType>scope</activityType>
<evalPoint>completion</evalPoint>
<durationInSeconds>0.011</durationInSeconds>
<duration>PT0.011S</duration>
</activityData>
<variableData>
<dataType>12</dataType>
<data>
<ns0:LCName xmlns:ns0="LC_Test1http://www.ulrhome.com/2008/10/L_Entry">LC_Test1</ns0:LCName>
</data>
<queryName/>
<target>$WriteL_Produce_Message_InputVariable/L_Entry/ns2:L_Entry/ns2:LCName</target>
<updaterName>AddL_Entry</updaterName>
<updaterType>scope</updaterType>
</variableData>
</payload>
</actionData>
My requirement is that I need to add a sensor to the BPEL process which posts 'Only my payload message to the JMS queue'..
What I would want the message in the Queue to be is : -
<data>
<ns0:LCName xmlns:ns0="LC_Test1http://www.ulrhome.com/2008/10/L_Entry">LC_Test1</ns0:LCName>
</data>
Also while creating a Sensor action I get another option as JMS Adaptor,I am not sure of what value to type in this wizard..Heres what I keyed in..M sure this is not right..Cos it dosnt work :-)
<action name="SensorAction_JMS" publishName="" publishType="JMSAdapter" enabled="true" filter="" publishTarget="jms/LoggingQueue">
<property name="JMSConnectionName">Log</property>
</action>
</actions>
Could any 1 tel me what values are the right values..And does JMS Adapter mean that I have to create a JMS Apator in the project and give that connection name as a Value..
I am not finding sufficiant Documentation for 'JMS Adapter' so M clueless and right now any help will be appriciated :-)
Regards,
Akshatha.

When we should use JMS based proxy services and when JMS Adapter in OSB

Hi,
Can somebody explain me when we could go for JMS Adapter and when we should go for JMS based service in OSB?
The one scenerio i can think of is when my provider/consumer is using jms provider other than WLS jms provider we should use jms adapter.
Edited by: user12883209 on Jan 5, 2012 5:29 AM

I don't think there are clear guidelines available, however here is my view.
1) OSB 11gR1 is not certified with Oracle JMS Adapter. It is certified with Oracle FTP, Database, AQ and application adapters.
http://docs.oracle.com/cd/E21764_01/doc.1111/e15867/interop.htm#OSBAG1403
2) In addition of the Weblogic JMS, OSB can also integrate with following provider without using adapter.
- WebSphere MQ
- Tibco EMS
3) if you need to integrate JMS with BPEL Process or Oracle SOA suite composite, it has built in support for generic Oracle JMS adapter. Oracle generic JMS adapter can integrate with AQ JMS (JMS providers OJMS 8.1.7, 9.0.1.4, and 9.2), TIBCO JMS, IBM Websphere MQSeries (IBM MQSeries JMS 6.0), Weblogic JMS, Apache, and Active MQ
http://docs.oracle.com/cd/E14571_01/integration.1111/e10231/adptr_jms.htm
4) If you need to integrate OSB with Weblogic JMS, WebSphere MQ, Tbco EMS it does not need JMS adapter.
Hope this helps !!!
Jayesh Patel
http://jayesh-patel.blogspot.com/
http://www.yagnasys.com/

Integration of websphere mq and Host

Hi,
I'm trying to find some information about the integration of this scenario:
WebLogic 1 Websphere 2 Websphere 3
<--> <--> <-->
Host(CICS)
Server MQ MQ
1 Integration is no Problem, you can use jms, and the normal java API
2 It is also no Problem, I think
3 Is also no Problem, because IBM has a solution
BUT WHAT is with the hole scenario. Are there any bottlenecks if you want to exchange
data from a J2EE Application on WebLogic to the Host(CICS) and back. Are there
any special things to handle, any Problem with Headers and so on.
If someone has an Idea or some suggestions, please let me know.
Thanks, Robert

Nitin,
A Tuxedo server (actually, all the servers in any group) can only access
1 resource manager.
To have Tuxedo access MQ and Orcale, you need separete servers and
server groups for the Oracle and MQ accesses. Then call both from a
single place where the transaction demarcation happens (or use AUTOTRAN
and tpforward from 1 server to the other)
Regards,
Peter.
Nitin wrote:
Hi Roopesh
thanks for your response.I have tried the sample prograame in which only Tuxedo
and Websphere MQ is involved . Its working fine.But when I try to use oracle the
server exits without giving any reason.I tried to debug the application using
gdb.The prgram is exiting with exitcode 0x377
Regards
Nitin
"roopesh" <[email protected]> wrote:
I think tuxedo should should act as transaction coordinator in this case.
IBM bundles sample programs for tuxedo with MQSeries.
check the following link
http://publibfp.boulder.ibm.com/epubs/html/csqzal09/csqzal09tfrm.htm
Thanks
"Nitin" <[email protected]> wrote:
I am developing a small programme which uses websphere MQ5.3
and Oracle 8.1.7.4.My server programme connects to a Queue Managerof
Websphere
MQ and opens a connection to the queue.But the MQCONN call of websphere
MQ fails
to connect to queue manager without giving any resaon code and the server
is terminated
giving LIBTUX_CAT:541.This is the situation when Oracle is used as a
resource
manager.If I dont use Oracle as a resource Manager the programme works
fine.
I am using HP-UX11.0 OS.
Any Suugestions???

Problem with sqlldr and commit

Hi,
i have a problem with sqlldr and commit.
I have a simple table with one colum [ col_id number(6) not null ]. The column "col_id" is primary key in the table. I have one file with 100.000 records ( number from 0 to 99.999 ).
I want load the file in the table with sqlldr ( sql*loader ) but i want commit only if all records are loaded. If one record is discarded i want discarded all record of file.
The proble is that in coventional path the commit is on 64 row but if i want the same records of file isn't possible and in direct path sqlldr disable primary key :(
There are a solutions?
Thanks
I'm for the bad English

This is my table:
DROP TABLE TEST_SQLLOADER;
CREATE TABLE TEST_SQLLOADER
( COL_ID NUMBER NOT NULL,
CONSTRAINT TEST_SQLLOADER_PK PRIMARY KEY (COL_ID)
This is my ctlfile ( test_sql_loader.ctl )
OPTIONS
DIRECT=false
,DISCARDMAX=1
,ERRORS=0
,ROWS=100000
load data
infile './test_sql_loader.csv'
append
into table TEST_SQLLOADER
fields terminated by "," optionally enclosed by '"'
( col_id )
test_sql_loader.csv
0
1
2
3
99999
i run sqlloader
sqlldr xxx/yyy@orcl control=test_sql_loader.ctl log=test_sql_loader.log
output on the screen
Commit point reached - logical record count 92256
Commit point reached - logical record count 93248
Commit point reached - logical record count 94240
Commit point reached - logical record count 95232
Commit point reached - logical record count 96224
Commit point reached - logical record count 97216
Commit point reached - logical record count 98208
Commit point reached - logical record count 99200
Commit point reached - logical record count 100000
Logfile
SQL*Loader: Release 11.2.0.1.0 - Production on Sat Oct 3 14:50:17 2009
Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.
Control File: test_sql_loader.ctl
Data File: ./test_sql_loader.csv
Bad File: test_sql_loader.bad
Discard File: none specified
(Allow all discards)
Number to load: ALL
Number to skip: 0
Errors allowed: 0
Bind array: 100000 rows, maximum of 256000 bytes
Continuation: none specified
Path used: Conventional
Table TEST_SQLLOADER, loaded from every logical record.
Insert option in effect for this table: APPEND
Column Name Position Len Term Encl Datatype
COL_ID FIRST * , O(") CHARACTER
value used for ROWS parameter changed from 100000 to 992
Table TEST_SQLLOADER:
100000 Rows successfully loaded.
0 Rows not loaded due to data errors.
0 Rows not loaded because all WHEN clauses were failed.
0 Rows not loaded because all fields were null.
Space allocated for bind array: 255936 bytes(992 rows)
Read buffer bytes: 1048576
Total logical records skipped: 0
Total logical records read: 100000
Total logical records rejected: 0
Total logical records discarded: 0
Run began on Sat Oct 03 14:50:17 2009
Run ended on Sat Oct 03 14:50:18 2009
Elapsed time was: 00:00:01.09
CPU time was: 00:00:00.06
The commit is on 992 row
if i have error on 993 record i have commit on first 992 row :(
Edited by: inter1908 on 3-ott-2009 15.00

Need to Return immediately and commit the App Module on a different thread

I have an action that I want to return fast (immediately) but the server processing takes longer than acceptable. The results of the operation don't matter to the page submitting it and I want it to be able to navigate away even if the operation is not complete. I want to either be able to send a non-blocking server event from the browser or on the server side start a new thread that performs the operation allowing the original thread to return immediately. The new thread would need access to an Application Module in order to commit data. How would I go about accomplishing this?
Some thoughts
I've tried creating a ConcurrentLinkedQueue and putting the DataControl on the que, then in the other thread I pull it off the que, process and commit the data. This works unless the page is navigated away from. Then calling dc.getApplicationModule(); returns null.
I thought about using createRootApplicationModule in the new thread (since the new thread has no context) but don't know how that would work
This is the code in the run method of the new thread. In this example, I'm adding data to the app module in the original thread and committing the data in a new thread.
(like I said, it works most of the time.)
Object[] req = (Object[])que.poll();
DCDataControl dc = (DCDataControl)req[0];
try{
ApplicationModule am = dc.getApplicationModule();
if (am != null){
am.getTransaction().commit();
} else{
System.out.println("AM:null unable to commit ");
} catch (Exception e){
e.printStackTrace();
finally{
if (dc!= null){ dc.resetState();} // release app module
}

Thanks for the replies. I am aware of the inherent risks of running a separate thread within a managed container.
The use case is a performance logging operation. We have a internal web app used by a network of franchises with over 1000 users. We log response time and performances statistics to the database. When the user clicks to navigate or commit data, the response time that the user experiences is logged after the page has fully rendered either through a PPR or a full submit. This is done by submitting ADFCustomEvent from javascript on the page after rendering is complete.. The event sends up the time difference from when the user first clicked to when the page was fully rendered. This information is then merged with logged events stored on the users Session that shows the name and response time of every query that was executed during the previous request. Depending on the page this could be up to half dozen to a dozen or more queries. The logging operation as experienced by the browser is generally fast (<200ms) but sometimes can be as long as a second or more when the database gets busy. A half second is too long as makes the app appear sluggish if the user can't type or click immediately after the page has finished rendering. The logged data is aggregated so we know exactly how much of the page load was due to a slow browser/network, how much was database time, webservice call time, etc... If it's due to a slow database we can drill down and see which query is the culprit. These performance metrics are critical to operations and are charted throughout the day so we know exactly what our users are experiencing. All of our users use a custom firefox client that we control. Using this logging framework we were able to determine that upgrading to a Firefox 4.0 based client cut browser render time by more than half a second on average. We can also tell what type of hardware the user is running so can place the blame for poor performance where appropriate. We have determined that pages render considerably faster on Windows 7 than on Windows 98 with the same hardware. We are moving the logging tables off of our exadata database to a separate box to remove that load from the application database. Since we expect the other database not to perform as well we don't want it to affect the user experience, hence the need to log asynchronously. I would like to put the data on a queue and have a background daemon process read from the queue and commit to the database. I would like the daemon thread to be able to use BC components. I would prefer not to resort to using a web service because of the inherent overhead. The logging operation is not a long operation but is of high frequency so should be as streamlined as possible. The load is spread over 6 servers with 4 JVM's each (24 weblogic instances). I know it's possible to use BC components from a plain Servlet (which runs on it's own thread) so what I want is to have something like a servlet thread that loops forever processing my logging queue.
One other method I am investigating is using my own non-blocking ajax call that callls a servlet to perform the logging. I will need to pull out the timestamp contained within a client side ADF component along with the pages ctrl-state variable that is included with every ADF request as it uses this as the key to get to the data on the session. ADF really needs a non-blocking ADFCustomEvent for this type of request. (send and don't care about the response)
The client component with the server listener looks like this
<af:outputText value="#{pageFlowScope.perfClientTS}" visible="false"
id="perfClientTSField" clientComponent="true">
<af:serverListener type="logPerfData" method="#{perfLog.logPerfDataAction}"/>
</af:outputText>
The script that queues the ajax call after the page loads looks like this
AdfCustomEvent.queue(perfClientTSField, "logPerfData", {
typeId : typeId,
subTypeId : subTypeId,
responseTime1 : new String(responseTime1),
responseTime2 : new String(responseTime2),
openedVia: via
true);
I also tried calling the noResponseExpected() method on the event before queuing it but it still blocked the UI and caused an additional side effect in that the client sent two ajax requests instead of one. It somehow thought something on the client side needed to be synced with the server.
email me and I can send a doc with more details about how our performance logging framework works.
Edited by: Don Kleppinger on Mar 14, 2012 2:52 PM

Unable to get values within scope of the RowGroup(only got values using Previous and current scope value)

Hi All,
I already calculated a row(Add Total row) like Gross profit within Group1 (a,b,c,d,e which are sub groups) using Previous and current scope column group values. ex: Gross Profit = a - b. (within group1)
Gross Profit = Previous(Sum(Fields!Trans_amount.Value)) - Sum(Fields!Trans_amount.Value) in Group1
Now, I want to get values for Net income like Net income = a - b - c in Group1. (OR)
Net income = Gross Profit - c in Group1 (Using Gross Profit textbox values using Reportitems!textbox.value). but, values different. Since Expression got new calculation)
Please help me.
Thanks Advance.
- Prem Kumar T D http://www.sharepointbasic.com/

Hi Premtd,
As per my understanding, there are group and subgroups in the report, you added total to a group with the expresson: Previous(Sum(Fields!Trans_amount.Value)) - Sum(Fields!Trans_amount.Value). You want to add a text box to the report to calculate Net income
with the expression: Previous(Sum(Fields!Trans_amount.Value)) - Sum(Fields!Trans_amount.Value) - Sum(Fields!Trans_amount.Value). In order to improve the efficiency of troubleshooting, I need to ask several questions:
• “I already calculated a row(Add Total row) like Gross profit within Group1 (a,b,c,d,e which are sub groups)” What’s the meaning of Group1 and subgroup a, b, c, d, e ? Could you please mark Gross profit and the groups in the screenshot?
• How to calculate Net income? Please provide some more detailed information of your requirements. I would be appreciated it if you could provide sample data and clear screenshot of the report.
This may be a lot of information to ask for at one time. However, by collecting this information now, it will help us move more quickly toward a solution.
If you have any more questions, please feel free to ask.
Thanks,
Wendy Fu

What is the significance of the Assembly Deployment Target and Feature Scope?

Hello,
We have created a project as Farm Solution (not sandbox).
Under project properties we can see an option for Assembly Deployment Target : GAC or WebApplication.
I know that GAC will deploy the dll to windows\assemblies and WebApplication will deploy to website/bin folder.
Now, we add a feature to the project; in here we can see a dropdown for scope with options as: Farm; Web; Site; WebApplication. I know that depending upon what option is chosen; the feature can then be activated by going to the respective manage features
option via SharePoint front end UI.
Can you tell me what is the significance of the Assembly Deployment Target and Feature Scope?

>>Can you tell me what is the significance of the Assembly Deployment Target and Feature Scope?
Feature scope can be decided based on the type of artifacts you will be building
Check the below link for what type of artifacts can be build at different levels of scopes
http://msdn.microsoft.com/en-us/library/ms454835(v=office.14).aspx
wrt to Assembly Deployment Target depends on what type of components you are deploying through your solution which will be specified in manifest.xml. There are advantages
if you deploy the components to web application rather GAC like all Apppools will not get recycled, avoiding IIS reset etc. But if you have 3rd party dlls and feature receivers which need to deployed along with the solution then its advisable to deploy to
GAC
http://trentacular.com/2009/06/sharepoint-differences-between-global-and-web-application-targeted-solution-deployment/
https://www.captechconsulting.com/blog/james-brocato/sharepoint-without-the-gac
Hope this helps.
My Blog- http://www.sharepoint-journey.com|
If a post answers your question, please click Mark As Answer on that post and Vote as Helpful

Want to know more about Business Analytics in SAP and its scope

Hi all,
I would like to know more about Business Analytics in SAP and its scope. My wife has finished her MBA (HR) and currently working as HR. She is more interested Business analytics, so please guide her how to startup her career in this field in the entry level, what prerequisites should be met and how the job market will be.
Thanks a lot in advance.
Srini

Dear,
Its good decision to go with Business Analytics in SAP ERP.
Both businesses and SAP AG no more requires consultants, requires efficient dynamic skilled business analytics professionals to advance in current international market. Business Strategic planning plays a major role in Business Analytics.
If you search google with "Business analytics" you will find hundreds of results which everyone of us has to read and learn what really stands for Strategy and Planning.
http://www.sap.com/corporate-en/press.epx?pressid=14491
http://marksmith.ventanaresearch.com/2011/02/25/sap-retrofits-business-intelligence-and-information-management-to-meet-it-and-business-needs/
http://www.sap.com/solutions/sapbusinessobjects/index.epx
As you mentioned, its not a difficult task for an MBA(HR) person to read and understand the subject available.
Please check and Best of luck.
Regards,
Syed Hussain.
P.S: "no more requires consultants" my intention is already plenty of consultants in market today. When competition is tough and plenty - invent new technologies and upgrade.
Edited by: Syed Hussain on Jun 22, 2011 9:21 AM

Lock and Commit work in INBOUND IDOC

Hi Experts,
Problem is about lock and commit work
i need to receive idoc for Good receipt for purchase order.
For one Purchase Order i can receive many good receipt Idoc at the same time and when first came in Lock the Purchase Order and further idoc came after give Errors becouse purchase Order is lock.
Problem is not the serialization (the sequence is correct), but is the lock.
Any idea on how to fix this issue? (maybe there is some std settings??)
Cheers
Boris

Hello Guys
the packetsize is already set to 1 but the problem still again..... and where i can find this setting   "in Customizing choose Engineering Change Management ® Define statuses for master record". ?
Any way i try in function module in inbound to check the lock object with this sample code:
      DO 30 TIMES.
        CALL FUNCTION 'ENQUEUE_EMEKKOS'
         EXPORTING
           mode_ekko            = 'S'
           mandt                = sy-mandt
           ebeln                = goodsmvt_item-po_number
           _scope               = '2'
         EXCEPTIONS
           foreign_lock         = 1
           system_failure       = 2
           OTHERS               = 3.
        IF sy-subrc <> 0.
          WAIT UP TO 1 SECONDS.
        ELSE.
          EXIT.
        ENDIF.
      ENDDO.
but also with this....problem syill again...
thanks
Boris

Problem in Creating new row & inserting data using CreateInsert and Commit

Hello All,
I have created a page there are few input text and i want to insert the data into a database table. I have created an Application Module I am using CreateInsert and Commit operation but there is one problem.
At first it created a row in database after that it is not creating the new row instead it is updating the same row with the new values.
In bindings of my jspx page I have created two binding for action (1) CreateInsert for the VO of that Application Module (2) Commit operation of that Application Module.
Here is the code snippet of my application:
BindingContainer bindings = getBindings();
OperationBinding operationBinding = bindings.getOperationBinding("CreateInsert");
Object result = operationBinding.execute();
*if (!operationBinding.getErrors().isEmpty()) {*
return null;
OperationBinding operationBinding1 = bindings.getOperationBinding("Commit");
Object result1 = operationBinding1.execute();
*if (!operationBinding1.getErrors().isEmpty()) {*
return null;
I have tried using Execute+Commit and Insert+Commit case also in every case it is updating the same row and not inserting a new row.
Is there anything I am missing?
Please Help.

hi user,
i dono. why are trying with codes. adf provides zero lines codes.
a wonderful drag and drop functionality provide by the framework.
while double click the button the codes are registered in your bean
    public String cb6_action() {
        BindingContainer bindings = getBindings();
        OperationBinding operationBinding = bindings.getOperationBinding("CreateInsert");
        Object result = operationBinding.execute();
        if (!operationBinding.getErrors().isEmpty()) {
            return null;
        return null;
    public String cb8_action() {
        BindingContainer bindings = getBindings();
        OperationBinding operationBinding = bindings.getOperationBinding("Commit");
        Object result = operationBinding.execute();
        if (!operationBinding.getErrors().isEmpty()) {
            return null;
        return null;
    public String cb7_action() {
        BindingContainer bindings = getBindings();
        OperationBinding operationBinding = bindings.getOperationBinding("Delete");
        Object result = operationBinding.execute();
        if (!operationBinding.getErrors().isEmpty()) {
            return null;
        return null;
    public String cb14_action() {
        BindingContainer bindings = getBindings();
        OperationBinding operationBinding =
            bindings.getOperationBinding("Delete4");   // some different here. after deleting usually do commit
        OperationBinding operationBinding1 =
            bindings.getOperationBinding("Commit");    // so here commit operation.
        Object result = operationBinding.execute();
        Object result1 = operationBinding1.execute();
        if (!operationBinding.getErrors().isEmpty()) {
            return null;
        if (!operationBinding1.getErrors().isEmpty()) {
            //add error handling here
            return null;
        return null;
    }if am not understud correctly. please some more explanation need.

Issue with Transporting Trans and Comm Structure

Hi Experts,
Recently we moved an Infosource ( with Transfer structure and Comm stucture) from D to Q. After movement we checked teh Transport log and we see a warning that says
" R3TRROUT458SEFRDF2PUBJRIZGZAOPSNB not found, object also deleted in target system"
From teh object name it appears like a routine. But how do we know the actual name of the routine so that we can see in find out and compare betwn systems.
Thanks
DVMC

Hi,
If you want to find the objects using only technical name, use the table TADIR.
In your case execute this table and give the technical name
'458SEFRDF2PUBJRIZGZAOPSNB' (Removed R3TR and ROUT).
Then you can get the routine details.
Regards,
Vivek V

CreateInsert And Commit Programmtically

dear all
how i can
programmtic CreateInsert action And Commit action into one commandButton.
h

Hi,
You can CretaeInsert and Commit using bindings as follows
BindingContainer bindings = getBindings();
OperationBinding operationBinding = null;
//access the ADF commit operation in an Operation binding and
//execute it
operationBinding = bindings.getOperationBinding("CreateInsert");//
Object result = operationBinding.execute();
if (!operationBinding.getErrors().isEmpty()) {
//don’t continue in the case of an error
return null;
}For Commit,Same code as above just change above CreateInsert to Commit as follows
operationBinding = bindings.getOperationBinding("Commit");//Access bindings
public BindingContainer getBindings() {
return BindingContext.getCurrent().getCurrentBindingsEntry();
}

CreateInsert and Commit in one operation

Is there a way to CreateInsert and Commit in one operation? I just want the user to click one button to create a new record.

Hi..
You can try as this scenario one way is without bean class also you can with bean any way i will explain how do you do without bean
Refresh your Data Control and say you have ViewObject name sampleVO and Application Module as AM.
Drag and drop CreateInsert as ADF Button(DataControl --> AM -->sampleVo --> Operations --> CreateInsert),To fill data for newly created row Drag and Drop sampleVO as ADF - Form(DataControl --> AM--> sampleVo).Now want to commit this form to database for that purpose you can use Commit Operation in your Application Module Drag and Drop Commit as ADF Button(DataControl --> AM --> Operations -->Commit).Now you can successfully inserted data to DataBase using CreateInsert and Commit.

ADF 11g Taskflows and PageFlow Scope.

Hi,
I am working in ADF11g and I have a question on ADF Taskflows and PageFlow Scopes.
I have 2 bounded taskflows a and b. a is in showdetailitem1 and b in showdetailitem2. I have created a bounded taskflow on a and b and dropped on a page.I have some values set in page flow scope of a and when I try to retrieve those values in b, I get them as null.
Can anyone tell me what could be wrong.
Thanks,
User

Hi,
As i understand, each bounded taskflow will have a separate pageFlowScope. I believe, I have read this before in the documentation but now having a hard time finding it. If you need to share the same variable between bounded taskflows, you can look into taskflow parameters or contextual events. Another dirty and easy way is to use session scope (not recommended if can be avoided).
Regards,
Pino

JMS, MQ WebSphere messagesplit and commit scope

Similar Messages

Maybe you are looking for