Journaling mailbox - Exchange 2013 Migrations from 2010

hi guys
i am about to start mailbox movement from Exchange 2010 to 2013. my setup is working fine. i have enabled journaling from Exchange 2010 and as ii found, automatically journaling rules will be reflected to exchange 2013. i had very big journaling mailbox
and then newly created New Exchange 2010 journaling mailbox. now new journaling mailbox is configured for journaling and that also still on 2010(both Old and new journaling mailbox ), new mailx is couple of weeks old (6-8 GB) and old one is 2.6 TB. So i will
move old one at the end .
my questions is if i move new journaling mailbox to 2013 before start normal Mailboxes, it will cause some issues for journaling. i use premium journaling . is it okay to move journaling mailbox at the begin ??
thank you
Indunil

Hi,
Based on my test, journal rules will be synchronized in Exchange 2013 after you create in Exchange 2010. If you create in Exchange 2013, then the rule will be synchronized in Exchange 2010.
And I did create a rule to send message to a Exchange 2013 jounal mailbox for Exchange 2010 users. It worked.
So you can migrate journal mailbox to Exchange 2013 firstly based on this test.
Best regards,
Belinda Ma
TechNet Community Support

Similar Messages

Exchange 2013 Migration from 2010 Test (Shared split DNS)

Hi
Im testing a migration from Exchange 2010 to 2013. I have tried to run a single DNS name to both servers, so externally mail.test.com resolves to the external IP and that NAT's to the new Exchange 2013. Then internally mail.test.com resolves both to EXC13
and EXC10 ip adresses (Round Robin).
I have moved some mailboxes to 2013. If the IP resolves to the new Exchange and i try to login to a mailbox on the old server i get redirected as im supposed to. If the IP resolves to the old Exchange and i try to login with a mailbox on the new server i
get:
A server configuration change is temporarily preventing access to your account. Please close all Web browser windows and try again in a few minutes. If the problem continues, contact your helpdesk.
Should this be possible, or do i need to change the intarnal URL on all virtual directories on the old server to the local netbios name or what to do?

You should never use the server name in any of the URLs. You should use either a CNAME or a load-balanced VIP with a generic name like mail.company.com or webmail.company.com. Then you just point this name to the new server. If
you're currently using a server name, it's about time to change that first before trying to switch to Exchange 2013.
Curently im using a generic name, mail.test.com. But that's just a normal A record on the internal DNS. So i cannot use that on both?

Exchange 2013 upgrade from 2010 and no mail flow and cannot move mailboxes

I am in the process of moving to Ex 2013 from 2010. I have installed Ex 2013 SP1 on a new server 2012 R2. All of my Ex 2010 servers are SP3 RU 5. Ex 2013 is running and I can connect through the EAC and see all other Exchange servers and connectors that
were already in existence. Several puzzling things are happening now that the servers are in coexistence:
1) As soon as Ex 2013 was installed on the network, many Outlook users are continuously being prompted to enter their domain credentials. They can cancel the prompt and Outlook still sends/receives email. No user mailboxes are on Ex 2013 yet.
Why is this happening?
2) I am following the Ex 2013 Deployment Assistant and I get to the step to move the Ex 2010 Arbitration mailbox to Ex 2013 and the move does not happen--it just says "syncing" and never completes. I tried moving a test mailbox from Ex 2010
to the 2013 database and I get the same result. I created the move request on the Ex2013 server and I see it as queued on the Ex2010 server, so I know they are "talking" to each other. However, when reviewing the status of the move I
see "MapiExceptionNoAccess: Unable to open message store".
3) There seems to be no mail flow on the same Ex2013 server or between the Ex 2010 and 2013 servers. I created two new test user mailboxes in Ex 2013. The Ex2013 mailboxes cannot send/receive to each other or to Ex 2010 users. This
seems strange, unless I am completely missing something in the Ex 2013 install?
I know this is a lot in one post, but following the Deployment assistant, I was hoping this would be something that others have faced. Thanks for any input here.

Does the below points already fit for you.
Exchange 2013 Supported with the following minimum versions of Exchange:
1) Exchange*** 2010 SP3 on all Exchange 2010 servers in the organization, including Edge Transport servers.
2) Exchange 2013 CU2 or later on all Exchange 2013 servers in the organization.
*** If you want to create an EdgeSync Subscription between an Exchange 2010 Hub Transport server and an Exchange 2013 SP1 Edge Transport
server, you need to install Exchange 2010 SP3 Update Rollup 5 or later on the Exchange 2010 Hub Transport server.
Thanks Prem P Rana MCSA Messaging 2003 MCSE 2003 Server MCTS MCITP Exchange 2007, 2010 Gurgaon, India http://blogs.msexchange-experts.com

Server 2012 and Exchange 2013 Migration from SBS 2011

Server UpgradeI'm migrating an SBS 2011 server to a new machine with Server 2012 R2 and a Hyper-V server running Exchange 2013. I've set up the new machine, all is running well in a test environment. I now want to migrate the old server to new. These are the steps I'm going to take and I wanted advice for any modifications or errors. 1. Demote DC on Server 2012 that I set up to test. 2. Join new Server 2012 to existing SBS 2011 domain. 3. Promote Server 2012 to DC. 4. Join the Hyper-V Server 2012 to the Server 2012 domain.5. Migrate Exchange 2010 on the SBS 2011 Server to Exchange 2013. 6. Transfer FSMO role from SBS 2011 Server to Server 2012 DC. I'll copy shared data files using robocopy.The only things I'm not sure about is the FSMO order, when to do that and the fact that I already have Exchange 2013 installed in the test...
This topic first appeared in the Spiceworks Community

I recently acquired a SuperMicro chassis that has a SAS2 expander backplane. It has SFF-8087 ports on it.http://www.supermicro.com/manuals/other/BPN-SAS2-846EL.pdfI made a post on another forum and someone mentioned that the card couldn't be used with that backplane since it's a SATA controller, however, the backplane is both SAS and SATA device compliant, it's only the RAID controller, as far as I know, that is a "SATA II" controller, and not a SAS controller.So, I couldn't find anything in the official documentation of this controller on whether or not it was able to control SAS devices. The card itself has a 3 SFF-8087 ports though, couldn't this theoretically still be used with a SFF-8087 to SFF-8087 cable(seen below)since the backplane is a SAS/SATA backplane?...

Outlook clients cannot connect Exchange 2013 cutover from 2010

Hello,
My company has been running an Exchange 2013/2010 coexistence. Currently, Exch 2013 (2mbx and 1 CAS) utilizes "mail2.domain.com" for the name space. Exch 2010 (1MBX 1 CAS) uses "mail.domain.com"
We recently attempted to cutover external and internal DNS to point "mail.domain.com" and "autodiscover.domain.com" to the Exch 2013 server.
We changed all virtual directories on 2013 to use "https://mail.domain.com/owa" (ECP, EWS, etc. were changed too) for the internal and external URL. The Exch 2010 virtual directories internal URL are set to "https://internalFQDN.domain.com/owa"
the external URLs are $null
Both CAS servers were setup to use Outlook Anywhere since this is how 2013 proxies to 2010. The internal URLs for both were set to "mail.domain.com" IIS authentication Methods (Basic, NTLM). ClientAuthenicsationMethod: NTLM.
For both servers the autodiscoverserviceinternaluri was set to: https://autodiscover.domain.com/autodiscover/autodiscover.xml
The 2013 server has two SSL certificates installed. One is a wildcard cert for "*.domain.com" and the other includes our SANs (mail.domain.com, mail2.domain.com, webmail.domain.com, autodiscover.domain.com) it also includes the FQDN for the 2010
and 2013 CAS servers.
I'm speaking in the past tense because we had to roll back. The problem was no Outlook user could connect. This goes for mailboxes hosted on the Exchange 2013 and 2010 servers. The error was: "Cannot
open your default e-mail folder" to "The connection to Microsoft Exchange is unavailable. Outlook must be online or connected to complete".
Everything else worked fine during the cutover. OWA 2013 login page proxied 2010 logins properly, Outlook 2011 could connect with EWS fine, Active-Sync worked without issues too.
It was only the Outlook 2010 and 2013 clients that could not connect.
We rolled back and everything is working as it was before with the separate namespace. That leads me to think it's something with Outlook Anywhere (RPC/HTTPS)
but the settings seem correct unless I'm missing something. Any help is appreciated.
Thanks!

Hard to say. I've had to change the router to point to the old server as mail wasnt getting in. But OWA did seem ok, although I couldn't send messages... I could only see the inbox and contacts etc.

Exchange 2013 transition from 2010

I have installed a single 2013 CAS server and a single 2013 MB server in my testlab. I already have a 2010 cas server, Hub Server, and mb server in the testlab. After installing 2013, and redirecting my mail to the 2013 CAS server, mail is flowing to
the 2013 MB server. In the Queue Viewer for the 2013 DB server, I see the message with the next hop being SITE:mysite; Version:14, Delivery Type is SMTP Relay to Mailbox Delivery Group; Status is Retry;
Error:
"Wednesday, June 19, 2013 12:11:19 PM" "[{LRT=6/19/2013 12:10:19 PM};{LED=451 4.4.0 Primary target IP address responded with: ""451 5.7.3 Cannot achieve Exchange Server authentication."" Attempted failover to alternate
host, but that did not succeed. Either there are no alternate hosts, or delivery failed to all alternate hosts. The last endpoint attempted was (IP of 2010 Hub:25};{FQDN=2010 Hub Server FQDN};{IP=2010 Hub Server}]"
Submission Undefined Ready 0
I am at a loss on how to correct this. Is there a jedi master out there that can help?

I know it has been a year since this thread, but I wanted to say thank you. This worked for me after many hours of troubleshooting. I thought just checking Anonymous users under the Permission Groups would work. But that isn't the case, I needed to add
"Exchange Server authentication" under the Authentication tab. I was able to telnet fine with the anonymous users, hence my hours of troubleshooting. Your post did it so THANK YOU!

Exchange 2013 migration, disable SSLOffloading on 2010 CAS servers

We just going through the Exchange 2013 migration from Exchange 2010. I have one or two questions when following the Exchange deployment Assistant. We have HLB where the certificates and we enable SSLoffload on the CAS server. So we don't have public CA's
on our CAS 2010 servers.
So on the documentation it says to run this command, were it will disable SSLOffloading and change to Basic authentication. Will my running outlook 2010 clients start getting certificate errors and will they work as normal ?
Get-ExchangeServer | Where {($_.AdminDisplayVersion -Like "Version 14*") -And ($_.ServerRole -Like "*ClientAccess*")} | Get-ClientAccessServer | Where {$_.OutlookAnywhereEnabled -Eq $False} | Enable-OutlookAnywhere -ClientAuthenticationMethod
Basic -SSLOffloading $False -ExternalHostName $Exchange2013HostName -IISAuthenticationMethods NTLM, Basic

We have OA enabled on all CAS 2010 servers with NTLM authentication and SSLoffloading box checked. We have also setup our CAS2013 and is running. My question above was that if I ran that command, Will I break anything since all my users
are still on Exchange 2010 mailboxes.
Then as I mentioned, that command will do nothing as OA is already enabled on CAS 10. It would only make a change if CAS10 had OA disabled.
Where {$_.OutlookAnywhereEnabled -Eq $False}
Where {$_.OutlookAnywhereEnabled -Eq $False}
Cheers,
Rhoderick
Microsoft Senior Exchange PFE
Blog:
http://blogs.technet.com/rmilne
Twitter:   LinkedIn:
  Facebook:
  XING:
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

Exchange server name not changing in mail profile after migration from 2010 to 2013

Following a migration from 2010 to 2013 we are finding that for a number of users the old exchange server address stays in the mail profile (control panel -> mail -> e-mail accounts) which causes Outlook not to load.
We are able to go into control panel -> mail -> e-mail accounts and change this manually to the new exchange 2013 server address but we have quite a number of users and don't really want to do it manually.
Shouldn't it be updating automatically and if so why is it?

Hi,
Yes, it should be changed by autodiscover. Does this issue occur to all the migrated users?
I have seen this kind of issues before when migrating from Exchange 2003/2007 to Exchange 2010. The most efficient way is to rebuild the Outlook profile.
Thanks,
If you have feedback for TechNet Subscriber Support, contact
[email protected]
Simon Wu
TechNet Community Support

Exchange 2010 to Exchange 2013 Migration and Architect a resilient and high availability exchange setup

Hi,
I currently have a single Exchange 2010 Server that has all the roles supporting about 500 users. I plan to upgrade to 2013 and move to a four server HA Exchange setup (a CAS array with 2 Server as CAS servers and one DAG with 2 mailbox Servers). My
goal is to plan out the transition in steps with no downtime. Email is most critical with my company.
Exchange 2010 is running SP3 on a Windows Server 2010 and a Separate Server as archive. In the new setup, rather than having a separate server for archiving, I am just going to put that on a separate partition.
Here is what I have planned so far.
1. Build out four Servers. 2 CAS and 2 Mailbox Servers. Mailbox Servers have 4 partitions each. One for OS. Second for DB. Third for Logs and Fourth for Archives.
2. Prepare AD for exchange 2013.
3. Install Exchange roles. CAS on two servers and mailbox on 2 servers. Add a DAG. Someone had suggested to me to use an odd number so 3 or 5. Is that a requirement?
4. I am using a third party load balancer for CAS array instead of NLB so I will be setting up that.
5. Do post install to ready up the new CAS. While doing this, can i use the same parameters as assigned on exchange 2010 like can i use the webmail URL for outlook anywhere, OAB etc.
6. Once this is done. I plan to move a few mailboxes as test to the new mailbox servers or DAG.
7. Testing outlook setups on new servers. inbound and outbound email tests.
once this is done, I can migrate over and point all my MX records to the new servers.
Please let me know your thoughts and what am I missing. I like to solidify a flowchart of all steps that I need to do before I start the migration.
thank you for your help in advance

Hi,
okay, you can use 4 virtual servers. But there is no need to deploy dedicated server roles (CAS + MBX). It is better to deploy multi-role Exchange servers, also virtual! You could install 2 multi-role servers and if the company growths, install another multi-role,
and so on. It's much more simpler, better and less expensive.
CAS-Array is only an Active Directory object, nothing more. The load balancer controls the sessions on which CAS the user will terminate. You can read more at
http://blogs.technet.com/b/exchange/archive/2014/03/05/load-balancing-in-exchange-2013.aspx Also there is no session affinity required.
First, build the complete Exchange 2013 architecture. High availability for your data is a DAG and for your CAS you use a load balancer.
On channel 9 there is many stuff from MEC:
http://channel9.msdn.com/search?term=exchange+2013
Migration:
http://geekswithblogs.net/marcde/archive/2013/08/02/migrating-from-microsoft-exchange-2010-to-exchange-2013.aspx
Additional informations:
http://exchangeserverpro.com/upgrading-to-exchange-server-2013/
Hope this helps :-)

Public Folder Exchange 2010 to Exchange 2013 Migration

hi guys
i have Exchagne 2010 SP3 and Exchange 2013 CU2 , i have moved all my mailboxes to Exchange2013 , before that i created Exchnage2013 Address Book ( web base ) for OAB . i have Public folder Database( used for Default Address book ) -Free/Busy on exchnage
2010 . now i don't need PF at all on Exchange 2013, So can i just Delete Public Folders from Exchange 2010 without Moving Public Folder ( free/Busyy , etcc... ) to Exchange 2013. from exchange 2007 to exchange , we did create Public folder
on Exchnage 2010 , Add replica , waited for sync, moved OAB generated Server as Exchnage 2010.
as i see from deploymetn guild, there are few steps need to be done to move PF to excahnge 2013, but since i don't need PF, can i just delete it.
Indunil

Hi
I m migrating public folder 2010 to 2013
When i do :
Get-PublicFolderMigrationRequest | Get-PublicFolderMigrationRequestStatistics -IncludeReport | Format-List
I have a lot of line like this
00-00-00-00-1A-44-73-90-AA-66-11-CD-9B-C8-00-AA-00-2F-C4-5A-03-00-36-B9-C6-5D-38-99-D6-11-9B-D6-00-08-02-55-A6-70-00-00-00-18-33-94-00-00 ». Ce dossier peut être
lié manuellement en exécutant la cmdlet Enable-MailPublicFolder une fois la migration terminée.
23/05/2014 19:18:02 [serveur] Avertissement : échec de recherche ou de liaison de l'objet destinataire « 96-7D-85-6C-DC-A6-83-42-AC-77-A4-5E-BD-CD-52-9B » dans
Active Directory pour le dossier public à extension messagerie « Public Root/IPM_SUBTREE/Secrétariat RC/PAYS/VENEZUELA/2006/SINCOR » avec l'ID d'entrée «
00-00-00-00-1A-44-73-90-AA-66-11-CD-9B-C8-00-AA-00-2F-C4-5A-03-00-36-B9-C6-5D-38-99-D6-11-9B-D6-00-08-02-55-A6-70-00-00-00-13-4D-8A-00-00 ». Ce dossier peut être
lié manuellement en exécutant la cmdlet Enable-MailPublicFolder une fois la migration terminée.
it scared me, what does it means ? Do i do something wrong?
I have let it work
And when i check status i have this :
Statut: Failed
Détails status : Failed other
Syncstages : Copying message
Estimed transfert size : 0
Pourcentcomplete : 95
What do i do? Can You help me? I m a little scared right now
Thanks

Custom Auto Attendant Prompts through TUI not working for users who migrated from 2010 to 2013

In Exchange 2010, we started using unified messaging and set up Auto Attendants. We setup a admin role/RBAC for people of a security group to be able to update the message on the auto attendants. They have the UMPrompts assigned role. All of this is working
great in 2010. We have now migrated to 2013, and the users who were migrated from 2010 to 2013 can no longer update the messages through TUI. Newly created 2013 users can and are assigned the EXASCT same permission as the users who have been doing this for
well over a year on 2010. When they call the AA and press #,* they are asked to provide their extension, after doing so the system tells them that extension is not correct. and asks for the extension again. Newly created users with the same permissions
get prompted for their PIN and can log in and change the message just fine.
Confirmed Bug? anybody else having this issue?
What would be different for this process between a user who was migrated from a previous version like 2010 compared to a newer user who has only ever existed on 2013?

What if the migrated 2010 users are in the same DB as the system mailbox? I had a similar issue during a migration; http://www.skypeadmin.com/2014/11/10/known-issue-um-automated-attendant-tui-editing-broken-migration/
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
SWC Unified Communications
This forum post is based upon my personal experience and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.

Exchange 2013 Issue: Outlook 2010 auto populating the From Tab when forwarding email

Exchange 2013 Issue: Outlook 2010 auto populating the From Tab when forwarding email
I am running Exchange 2013 and I have an end user who connects to it via Outlook 2010. All was going well till he went to forward an email and he noticed that the From button appeared and auto populated the sender's email address.
I have clicked the Empty Auto Complete List in Outlook's Send messages... still displayed the From tab when forwarding.
I recreated the profile in outlook... same thing.
I created the profile with outlook 2013... same thing.
There is only one user profile setup in Outlook.
(I know the from tab usually appears when you have multiple profiles setup in Outlook and/or when you configure the "From" tab.)
I opened the end user's email in Exch 2013's OWA... what was different here was when I clicked on the email and it opened, it did NOT have the Reply or Forward option... and it displayed as a "Draft" email.
Does anyone have any ideas?

So are you saying that the from button is filling the option with the original senders address (eg the person who sent the message to your user), or that it's filling in the your users address (in which case I don't understand what the issue is, since
it IS going from your user)?

Issue with Excel Access Web Part, with sites that were migrated from 2010 SP to 2013 SP

Hello,
If I try to add an Excel Access Web Part to a page I get the following:
**Note: This only happens with sites that were migrated from 2010 SharePoint to SharePoint 2013. If I create a new site the feature works like it should and loads the workbook. I've tested this on several sites, our environment is enterprise as well. Being
that the majority of our sites were migrated from 2010, I need this to work!

Can you try below fix and let me know
http://blogs.technet.com/b/excel_services__powerpivot_for_sharepoint_support_blog/archive/2013/05/21/excel-services-the-workbook-cannot-be-opened.aspx

Migration from 2010 to Office 365

I'm stumped on Office 365 Small Business Premium and the migration from 2010.
I thought that migration would be simple but I can't find any tools mentioned in the articles I read. I thought that it was supposed to be a tool found within 365 where you pull the info from the PST you keep on your desktop.
Do I need to uninstall 2010 and only use the 365 web based email. IF I can keep both, do they sync? Does this sync with the mobile app also?
So right now I have both installed and the users setup for 365 (the login accounts), but I don't have any thing else setup because I don't want to lose any data. I want to make sure that I do this right before I go any further.
No I don't have exchange. Every thing is hosted by Network Solutions and we use pop3 to pull the email.

Hi,
some options/suggestions are here:
http://community.office365.com/en-us/f/158/p/230137/714965.aspx?ss=87fa5dc5-cfde-49c9-ab80-294fc73ccb85#714965
http://community.office365.com/en-us/p/helpcenter.aspx?hcs=8b0e9324-aae1-4a96-a035-619cabe78397#ESKU-Admin-Mail
Don
(Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)
OK. I downloaded those files and they didn't do me any good. The one which would run was asking for a central computer, I'm assuming an email server, which we don't use.
We use pop3 through Network Solutions. We have Outlook on each desktop and the folders are local.
I am reading up on some other stuff on migration. I'll let you know how it goes.

Publish Exchange 2013 using UAG 2010 Sp4

Hi,
We need to publish Exchange 2013 through UAG 2010. But we are not getting any dedicated link for UAG 2010 to publish Exchange 2013. we have UAG 2010 with SP4.
Is there any Step by step UAG 2010 configuration link to publish Exchange 2013?
Thanks
jitender

Hi Jitender,
Based on my knowledge, publishing Exchange 2013 with UAG 2010 is similar with publishing Exchange 2010.
I find a related Blog and Guid for your reference:
1. Publishing Exchange Server 2010 with Forefront UAG and TMG
http://blogs.technet.com/b/exchange/archive/2010/07/16/publishing-exchange-server-2010-with-forefront-uag-and-tmg.aspx
2. Publishing Exchange Server 2010 with Forefront Unified Access Gateway 2010 and Forefront Threat Management Gateway 2010
http://www.microsoft.com/en-us/download/details.aspx?displaylang=en&id=8946
Please also notice the System requirement of both Exchange 2013 and UAG 2010.
System Requirement
Exchange 2013
http://technet.microsoft.com/en-us/library/aa996719(v=exchg.150).aspx
UAG 2010 SP4
Supported Operating System
Windows Server 2008 R2
Servers running Forefront UAG and SP4 require the following:
• Windows Server 2008 R2 Standard, Windows Server 2008 R2 Enterprise, or Windows Server 2008 R2 DataCenter.
• Microsoft Forefront Threat Management Gateway (TMG) 2010 Service Pack 2
Thanks
Mavis Huang
TechNet Community Support

Journaling mailbox - Exchange 2013 Migrations from 2010

Similar Messages

Maybe you are looking for