Jumpstart on T2000 with SOL 01/06 fails
Hi Gurus,
the problem:
jumpneu => Install-Server 10.245.129.145
xserv3 => boot-Server 10.245.129.18
Running the command: boot net -v install
Everythings runs well until: NFS server jumpneu not respondig still trying
TFTP is ok.
bootparams-file accessed
sysidcfg accessed but after that the error appeared.
Here are the last lines from the "boot net -v install" output:
Using RPC Bootparams for network configuration information.
Attempting to configure interface ipge3...
Skipped interface ipge3
Attempting to configure interface ipge2...
Skipped interface ipge2
Attempting to configure interface ipge1...
Skipped interface ipge1
Attempting to configure interface ipge0...
Configured interface ipge0
Beginning system identification...
Searching for configuration file(s)...
Using sysid configuration file 10.245.129.145:/jumpstart/Sysidcfg/Solaris_10/sysidcfg
Search complete.
Discovering additional network configuration...
Completing system identification...
Starting remote procedure call (RPC) services: done.
NFS server jumpneu not responding still trying
I don't know what mount should mounted.
bootparams-file:
ctx710 root=jumpneu:/jumpstart/SunOS.5.10_0106/Solaris_10/Tools/Boot install=jumpneu:/jumpstart/SunOS.5.10_0106 boottype=:in sysid_config=jumpneu:/jumpstart/Sysidcfg/Solaris_10 install_config=jumpneu:/jumpstart rootopts=:rsize=8192
Shares at jumpneu:
jumpneu[root]/jumpstart/Config: share
- /jumpstart ro,anon=0 ""
- /export/home ro,anon=0 "home directories"
- /export/jumpstart/SunOS_5.8 ro,anon=0 "Jumpstart Sol8"
- /export/jumpstart/SunOS_5.9 ro,anon=0 "Jumpstart Sol9"
- /export/jumpstart/SunOS_5.9/Software ro,anon=0 "Software Sol9"
- /export/jumpstart/SunOS_5.9/Patches ro,anon=0 "Patches Sol9"
- /export/jumpstart/SunOS_5.10 ro,anon=0 "Jumpstart Sol10"
- /export/jumpstart/Bungee ro,anon=0 "Jumpstart Config"
Because /jumpstart is shared, the subdir also shared ( referencing in bootparams file).
Mount on boot-Server:
Filesystem kbytes used avail capacity Mounted on
/jumpstart-bn:/jumpstart
17385770 15831289 1380624 92% /jumpstart
Any hints???
Is that the correct forum?
Regards
heinz
Hi,
we solved the problem!!!
in sysidcfg was an static entry for default_router!!!
We changed it => now we are happy
heinz
Similar Messages
-
CRM orders in R/3 with rejected (cancelled) lines fail on billing.
Hi,
I have issue in the replicatuion of the orders and Invoice generation in R/3 system.
u2022CRM orders in R/3 with rejected (cancelled) lines fail on billing.
u2022CRM orders in R/3 have the value of the rejected lines included in the order header.
u2022CRM orders in R/3 have the rejected/cancelled lines included in internal BW Traffic and Revenue Reports.
u2022CRM orders that have been saved but only contain rejected/cancelled items can be confirmed and passed to R/3.
your inputs will be appreciated!!
Regards,
Sathya.Already answered
-
when Update to 10.7.2 ,I cannot access to any site with ssl connection and fail to open safari and keychain, unless restart computer and login in with Guest account.
OS:10.7.2
Macbook Pro 2010-mid 13inchI also have the same problem, however if I use Firefox or Opera sites with ssl connection work fine. Still, I can't use Google Chrome (ssl), Safari (ssl), the Mac app store (generally), or the iTunes store (generally). Both the iTunes store, Safari and the app store won't respond, and Chrome displays this error: (net::ERR_TIMED_OUT). The problem persists regardless of what network I'm using. Also, when trying to access the keychain or iCloud, the process will not start (will hang). I didn't have these problems at all before updating to 10.7.2.
Sometimes rebooting helps, and sometimes not. If the problem disappears by rebooting, then it only lasts a few minutes before it reappears. It is very frustrating, especially since there doesn't seem to be any obvious or consistent way of which to fix it.
I'm also using a Macbook Pro 13-inch mid 2010. -
When my iPhone 4S (with ios7) experiences a failed call while connected to my Bluetooth hands free in my car(screen locked) the failed call appears on the locked screen, as it should, the problem arises whenever I unlock the phone, it automatically redials the last failed call, it doesn't do this with missed calls that are on the locked screen, if any. It is really annoying as sometimes the phone doesn't respond to attempts to end the call before it connects to the number. I then have to explain that it was my phone and not me, I look like an idiot, which I don't really need any extra help with!! Does anyone have any ideas? I don't want to stop missed call from showing in the locked screen but it might be associated with the failed calls and therefore be the only resolution
I have had the same issue which was driving me mad but think I have just found a way around it. In iOS 7 if you swipe up on the lock screen to access quick settings and go into timer then click the home button you get into the phone without calling the person back. Not a great 'fix' but hope it works for you. Come on Apple this isn't good enough, fix this bug otherwise you will lose your customers.
-
I got an issue with OS of widows 7.
unable to scan documents to user's PC.am getting error message "Authentication with the destination has failed. Check settings. To check the current status, press [Scanned Files Status
Other Windows xp PC can do this.
How can I fix this problem?
Printer Model :C2051 /mp2001spHi,
I searched for the error and it is mentioned in Ricoh's website:
Messages Displayed on the Control Panel When Using the Scanner Function
http://support.ricoh.com/bb_v1oi/pub_e/oi_view/0001045/0001045718/view/trouble/int/0036.htm
Please Note: Since the web site is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.
Message
Cause
Solution
“Authentication with the destination has failed. Check settings. To check the current status, press [Comm. Status/Print].”
The entered login user name or login password is not correct.
Check that the user name and password are correct.
Check that the ID and password for the destination folder are correct.
A password of 128 or more characters may not be recognized.
From the solution, it mentioned that the issue could relate to user account or its password.
Please let me know if it is in domain environment. If so, please test to log the same user account currently on Windows 7 to Windows XP and see if issue persists.
Also please test to directly access the scanning folder on printer server to see if there is any issue in accessing the destination folder. -
I have just upgraded to Windows 8 and my scyning and upgrading my phone with new apple software fails, Itunes looses connection with the device (phone), cant backup the phone or download new software, is this an issues with Windows
Hi, stig2013.
I would recommend the steps in the article below. See the section labeled Verify that the Apple Mobile Device USB Driver is installed > For Windows Vista, Windows 7, and Windows 8 > Update the Apple Mobile Device Driver.
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
If you are receiving an error message, find the exact error number that you recieved in the article below and process the steps.
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694
This error occurs when the device unexpectedly loses its USB connection with iTunes. This can occur if you manually disconnect the device during the restore process. You can resolve this issue by using USB troubleshooting, using a different Dock Connector or Lightning Connector to USB cable, trying another USB port, restoring on another computer, or by eliminating conflicts from third-party security software.
Cheers,
Jason H. -
I have recently upgraded a clients servers to Windows Server 2012 & since doing so have lost the ability to scan to folder.
Both servers are domain controllers and previously on a 2008 domain controller I would have had to make the following change to allow scan to folder:
Administrative Tools
Server Manager
Features
Group Policy Manager
Forest: ...
Default Domain Policy
Computer configuration
Policies
Windows Settings
Security Settings
Local Policies
Security Options
Microsoft Network Server: Digitally Sign Communications (Always)
- Define This Policy
- Disabled
However I have applied this to the Windows 2012 server but am still unable to scan, possibly due to added layers of security in server 2012. The error on the scanner is Authentication with the destination has failed check settings.
I have also tried the following at the server:
Policies -> Security Policies
Change Network Security: LAN Manager authentication level to: Send LM & NTLM - Use NTLMv2 session security if negotiated.
Network security: Minimum session security for NTLM SSP based (including secure RPC) clients and uncheck the require 128 bit.
Network security: Minimum session security for NTLM SSP based (including secure RPC) servers and uncheck the require 128 bit
I have created a user account on the server for the ricoh and set this in the settiings of the Ricoh and verified everything is correct.
Are there any other things I have missed?I can email anybody the firmware module if interested and how to...
Tell me your model and email
If your offer still stands we have an Aficio MP C3300
Firmwareversion
Modulnavn Version Delnummer
System/Copy 1.13 D0255562H
Network Support 8.16.1 D0255563D
Font EXP 1.03 D0255588
OptionPCLFont 1.02 D0255589
animation 1.3.1 D0255568A
Fax 01.10.00 D0255569B
RemoteFax 01.10.00 D0255564B
Printer 1.11 D0255572A
RPCS 3.7.5.4.1 D0255574A
Option PCL 1.00 D0255580A
Scanner 01.17 D0255570C
Network DocBox 1.00 D0255567B
Web Support 1.06 D0255565B
Web Uapl 1.07 D0255566C
libcvm(v4) 4.13 D4135765B
GWFCU3-13(WW) 03.00.00 D3935570C
PowerSaving Sys 1.10 D0255560C
Engine 1.51:09 D0255117E
OpePanel 1.03 D0251492A
LANG0 1.03 D0251496
LANG1 1.03 D0251496
ADF 03.420:02 D3665604
Finisher 01.090:03 D3725112
Best Regards/
Henrik Plougstad
henrik(a)pieroth.dk -
trying to download an instal ios 7 on my iphone 4s, after half an hour into the download it came up with a message saying failed and everytime i try again the download doesnt start. tried downloading from itunes aswel but not working. anyone know why?
The servers are overloaded. There are a hundred million people all trying to download iOS 7 at one time. Try again later
-
I have followed the "usual" way to build a pooled VDI desktop using Win7 or Win8 with success, but it fails when I use an image of Win Server 2012 as VM instead.
Am I overlooking something? Should I need to prepare the image in a different way? (Sysprep differently?)
ThanksHi,
Thank you for your posting in Windows Server Forum.
Can you specify the error which you are facing during VDI setup for server 2012?
I might think that you need to check the memory setting for server 2012, as might happens that due to less memory you can’t setup the VDI setup properly.
Memory: If the Master VM is configured with static memory, it must have at least 1024 MB as startup RAM. If the Master VM is configured with dynamic memory, the maximum RAM must be at least 1024 MB.
Please check beneath article for information.
Windows
Server 2012 2,500-user pooled VDI deployment guide (Doc)
Single Image Management for Virtual Desktop Collections in Windows Server 2012
Hope it helps!
Thanks.
Dharmesh Solanki -
Post Author: LeeCUK
CA Forum: Authentication
I have installed Enterprise XIR2 onto a Windows 2003 server and all services are running.I have installed the client on another windows 2003 server and I can connect to the console via the web.
Firstly desktop intel would not work and gave me the error below, however a new entry appeared in my server dropdown with servername (.Net Portal) and after selecting this Desktop intell worked.
When I try to run designer I dont get the extra server in the dropdown nor does it connect when tryped manually and gives me the same error I was getting for desktop intel.
Im using enterprise authentication
Has anyone figured this out please?
The error im getting is below[repo_proxy 13] SessionFacade::openSessionLogon with user info has failed(Transport error: Communication failure.(hr=#0x80042a01)Post Author: jsanzone
CA Forum: Authentication
LeeCUK:
The [repo_proxy 13] error seems to be a catch-all for BO in that I've worked with this software (XI R2) for 1 1/2 years now and each time I've encountered [repo_proxy 13] it has been for a different reason, thus, you're going to have to apply troubleshooting checks all over the place until you find the problem. In my particular case I just resolved my [repo_proxy 13] error I've been working on this week, and here was my scenario. Our server in the lab died due to a hard drive failure, so we cut our losses and installed a new & more powerful server. When the rebuild was done I could not connect from my laptop to the repository via Designer (good old [repo_proxy 13] error). After much angst, etc, etc I found out that the servers in the CMC (/businessobjects/enterprise115/admin/en/admin.cwrwere">http://<server>/businessobjects/enterprise115/admin/en/admin.cwrwere) were all down except for one (even though CCM showed all servers "up"). When I went to start the servers in the CMC I was prompted for an account, and no matter what account I tried it won't work. So I went back to the CCM servers and stopped them all, then changed the default account it was using from LocalSystem to the administrator account, restarted all servers in CCM, went back to CMC and noted that all servers were now up as well. Then I went back to my laptop and used Designer and was able to successfully log in. Thus, the end of my story, however, it seems that many [repo_proxy 13] errors have different beginning and endings. For instance, a year ago I had the same [repo_proxy 13] error and brought it to BO tech support. They determined that I had to uninstall my client from my laptop, clean out the registry for any references to BO keys, and remove the c:\program files \Business Objects folder, then reinstall, and sure enough it worked in that case, but not in this case when I tried it again. By digging deeper I found out the root cause to my current problem, and voila, I'm in!
Good luck! -
How can I copy test plan WITH ITS RESULTS (PASS/FAIL) to other project in MTM??
How can I copy test plan WITH ITS RESULTS (PASS/FAIL) to other project in MTM??
Hi odedn,
Thank you for posting in MSDN forum.
Based on your issue, you mean that you want to copy the test plan with test results from the current team project
to other team project, am I right?
If yes, as far as I know that when we copy test plan with test results to other team proejcts. It is default that
there just will not copy the test plan with test results (pass/fail) to other team project in MTM.
You can refer the following MSDN document’s
what gets cloned, it explained that which objects are copied from the source test plan to the destination test plan.
Reference:
http://msdn.microsoft.com/en-us/library/hh543843.aspx
If you still want to this feature, I suggest you can
submit this feature request:
http://visualstudio.uservoice.com/forums/121579-visual-studio. The Visual Studio product team is listening to user voice there. You can send your idea there and people can vote. If
you submit this suggestion, I hope you could post that link here, I will help you vote it.
Thanks for your understanding.
Best Regards,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey. -
I tried my first Windows CD burn with iTunes; the burn fails at different points during the burn, with error codes 4450 or 4280.
I have the same problem, after years of everything working great. Last time this happened I tried using a different brand of CD and it worked, but I must warn you that now iTunes rejects all three brands I have been trying to use.
-
Install NetConnect in Global Zone of Solaris 10 x86 with 5 local zone fail
Problem:
Install NetConnect in Global Zone of Solaris 10 x86 with 5 local zone failed
But I didn't have any issue with the same pkg in Solaris 9
Steps taken:
# groupadd netcon
# useradd -d /export/home/netcon -g netcon -m netcon
# vi /etc/shadow
change LK to NP
# ./UninstallNetConnect.003.002.001.sh
# ./InstallNetConnect.003.002.001.sh
Enter the user account to use: netcon
Enter group: netcon
Installing Sun(SM) Net Connect Proxy Core as <SUNWsrspx>
## Installing part 1 of 1.
/etc/opt/SUNWsrspx/CustomerCert.pem
/etc/opt/SUNWsrspx/SRSCACert.pem
/etc/opt/SUNWsrspx/binaries
/etc/opt/SUNWsrspx/srsproxyconfig.cfg
/opt/SUNWsrspx/bin/srsexec
/opt/SUNWsrspx/bin/srsinstall
/opt/SUNWsrspx/bin/srsinstallmode
/opt/SUNWsrspx/bin/srsproxy
/opt/SUNWsrspx/bin/srspxrun
/opt/SUNWsrspx/bin/srspxstat
/opt/SUNWsrspx/bin/srspxtrace
/opt/SUNWsrspx/bin/srsuser
/opt/SUNWsrspx/bin/srsxfer
/opt/SUNWsrspx/lib/srsimapi.jar
/usr/lib/libsrsimapi.so.1
[ verifying class <none> ]
## Executing postinstall script.
copying initial install customer cert into place
copying initial install srs cert into place
copying initial install proxy config file into place
removing any existing uninstallscript before copying the correct one
copying uninstall script into place
/var/sadm/pkg/SUNWsrspx/install/postinstall: /opt/SUNWsrspx/bin/srspxrun: cannot execute
proxy queue initialization failed
pkgadd: ERROR: postinstall script did not complete successfully
Installation of <SUNWsrspx> failed.
ERROR: pkgadd failed for: SUNWsrspx
Please correct this situation and rerun the installation.
Exiting installation.
# cat /var/adm/messages
Oct 7 00:00:01 planet root: [ID 702911 daemon.error] ERROR: proxy queue initialization failed
Any clue, or it will only possible in Global zone that didn't have any local zone
thanks in advanceProblem:
Install NetConnect in Global Zone of Solaris 10 x86
with 5 local zone failed
But I didn't have any issue with the same pkg in
Solaris 9
Steps taken:
# groupadd netcon
# useradd -d /export/home/netcon -g netcon -m netcon
# vi /etc/shadow
change LK to NP
# ./UninstallNetConnect.003.002.001.sh
# ./InstallNetConnect.003.002.001.sh
Enter the user account to use: netcon
Enter group: netcon
Installing Sun(SM) Net Connect Proxy Core as
<SUNWsrspx>
## Installing part 1 of 1.
/etc/opt/SUNWsrspx/CustomerCert.pem
/etc/opt/SUNWsrspx/SRSCACert.pem
/etc/opt/SUNWsrspx/binaries
/etc/opt/SUNWsrspx/srsproxyconfig.cfg
/opt/SUNWsrspx/bin/srsexec
/opt/SUNWsrspx/bin/srsinstall
/opt/SUNWsrspx/bin/srsinstallmode
/opt/SUNWsrspx/bin/srsproxy
/opt/SUNWsrspx/bin/srspxrun
/opt/SUNWsrspx/bin/srspxstat
/opt/SUNWsrspx/bin/srspxtrace
/opt/SUNWsrspx/bin/srsuser
/opt/SUNWsrspx/bin/srsxfer
/opt/SUNWsrspx/lib/srsimapi.jar
/usr/lib/libsrsimapi.so.1
[ verifying class <none> ]
## Executing postinstall script.
copying initial install customer cert into place
copying initial install srs cert into place
copying initial install proxy config file into place
removing any existing uninstallscript before copying
the correct one
copying uninstall script into place
/var/sadm/pkg/SUNWsrspx/install/postinstall:
/opt/SUNWsrspx/bin/srspxrun: cannot execute
proxy queue initialization failed
pkgadd: ERROR: postinstall script did not complete
successfully
Installation of <SUNWsrspx> failed.
ERROR: pkgadd failed for: SUNWsrspx
Please correct this situation and rerun the
installation.
Exiting installation.
# cat /var/adm/messages
Oct 7 00:00:01 planet root: [ID 702911 daemon.error]
ERROR: proxy queue initialization failed
Any clue, or it will only possible in Global zone
that didn't have any local zone
thanks in advance
[I believe that it does not work in x86, watches with pkginfo - l SUNWsrspx, in the platform.
Willy Suarez
Sopport UNIX
Colombia/code] -
CLUVFY failing with 'User Equivalence check failed for...'
New 2 node RAC configuration. Oracle 10gR2, Linux RHEL 5 x64. I'm at the post hardware config, pre install clusterware stage.
Running the cluster verification utility command:
cluvfy comp sys -n node-01,node-02 -p crs -verboseReturns the following error:
Verifying system requirement
ERROR:
User equivalence unavailable on all the nodes.
Verification cannot proceed.
Verification of system requirement was unsuccessful on all the nodes.I've verified the following:
1) RSA keys correctly configured on both nodes and I can ssh between without a password
2) ping ip and private work correctly to and from both nodes.
3) user, group ids are identical on both systems.
I also ran cluvfy stage -post hwos -n node-01,node-02 -verbose and received the following output. This output is from node-01. node-02's is identical, except with equivalence to itself failing.
Checking node reachability...
Check: Node reachability from node "node-01"
Destination Node Reachable?
node-02 yes
node-01 yes
Result: Node reachability check passed from node "node-01".
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
node-02 passed
node-01 failed
Result: User equivalence check failed for user "oracle".
WARNING:
User equivalence is not set for nodes:
node-01
Verification will proceed with nodes:
node-02
Checking node connectivity...I get the same behavior on both nodes. Not quite sure what else to check. Any thoughts or suggestions? Thanks.No, no banners. And I followed note 300548.1 to the letter. Several times :-)
However, I believe my issue has to do with a CVUHOME/cv/admin/cvu_config.
According to the documentation:
CV_XCHK_FOR_SSH_ENABLED—If set to TRUE, it enables the X-Windows check for verifying user equivalence with ssh. By default, this entry is commented out and X-Windows check is disabledIt was not, unfortunately, disabled by default - once I set it to false, everything succeeded. I still need to figure out why XCHK itself is failing, but I think I can troll through the log to figure that out. -
Posting payment to a company with sole proprietor
Hi,
Need you experts to help me address my query.
For companies with sole proprietor, the bank account name is
usually the owner's name instead of the company name. Currently, for
such cases, we amend the vendor name from the company to the bank
account (owner) name. Hence, payment is posted and made to the owner
not the company.
Is there a way (other than factoring) to maintain the vendor record
against the company name without affecting payment made to the owner's
bank account ?
Please help.
Thanks & Regards
AmmuHi Ammu,
First you should understand the system of SAP in FI. The purpose of spilitting is for legal records and statutory report submission.
In your case it is very clear the business has been operated and working according to the proprietor (Proprietorship). Here as per the income tax (other acts wont affect- Partnership act, companies act etc) authority all the transaction has to be done throught the owner's bank account only.
The same thing you can follow for your vendor. While creating the vendor you should assign vendor's (owner's bank account) bank account.
In your first paragraph you have mentioned "Hence, payment is posted and made to the owner not the company" here there is any question for company. Because your business transaction is not comes under "Companies Act 1956".
Please read the basis exercise in the books of "Direct Tax".
I am not clear your second paragraph: -
Is there a way (other than factoring) to maintain the vendor record
Against the company name without affecting payment made to the owner's
Bank account? - PLEASE BRIEF ME.
If you have any further clarifications please let me know.
Warm Regards,
Sivakumar Sathiyamoorthy
Maybe you are looking for
-
User Exit or BADI on saving of Sales order cost estimate (CK51N)
Hi, Can any one share with me what are the User Exit or BADI that gets triggered on saving of Sales order cost estimate (CK51N). Regards, Bijay
-
Itunes, iphoto, garageband, quicktime won't open, computer keeps freezing..
Hello, I am new to this forum, and am hoping to get some help. In just the last couple of days my computer has began to run a bit funky, freeze, and the pinwheel spins. I have to restart the computer, and sometimes can't even access the force quit. A
-
ClassFormatError when starting weblogic server on Solaris, SunOS 5.6
Hi, I get the following error when I start the server: startWebLogic.sh LD_LIBRARY_PATH=/sybase/sybase11/lib:/oracle/app/oracle/product/8.1.6/lib:/u sr/openwin/lib:/opt/SUNWspro/lib:/usr/atria/lib:/usr/java1.2/jre/lib/sparc:/ sybase/sybase11/lib:/ora
-
Can I listen to music when MacBook Pro Retina is closed?
Can I listen to music on MacBook Pro Retina when its closed? It can update when its closed as I know. Please reply!
-
ColdFusion 4.0 and Windows 2003 server
Greetings, I'm a newbie to coldfusion so please excuse the ignorance. I have a ColdFusion 4.0 applications sitting on a win2k that need move to a win2003 servers. Does 4.0 run on win 2003 and can be installed on it? The application is going to be ret