Jumstart install from x86 to x86 Solaris 10

I already posted this to the solaris 10 list, but I when checking this
forum it thought it more appropriate. My apologies to those who are active on both forums.
My setup is:
install server OS: Solaris 10, i86pc .
The install server is also boot server using tftpboot.
The dhpc server is configured according to the instructions which are
given when adding an install client in Solaris 10.
The client can communicate with the install and boot server but fails
to load the boot image. The snoop output is
Using device /dev/iprb0 (promiscuous mode)
cdm3 -> cdm2 ICMP Echo request (ID: 48130 Sequence number: 0)
cdm2 -> cdm3 TFTP Read "nbp.cdm2" (octet)
cdm3 -> cdm2 UDP D=2070 S=39122 LEN=22
cdm2 -> cdm3 TFTP Error: not defined
cdm2 -> cdm3 TFTP Read "nbp.cdm2" (octet)
cdm3 -> cdm2 UDP D=2071 S=39123 LEN=23
cdm2 -> cdm3 TFTP Ack block 0
cdm3 -> cdm2 TFTP Data block 1 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 1
cdm3 -> cdm2 TFTP Data block 2 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 2
cdm3 -> cdm2 TFTP Data block 3 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 3
cdm3 -> cdm2 TFTP Data block 4 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 4
cdm3 -> cdm2 TFTP Data block 5 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 5
cdm3 -> cdm2 TFTP Data block 6 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 6
cdm3 -> cdm2 TFTP Data block 7 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 7
cdm3 -> cdm2 TFTP Data block 8 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 8
cdm3 -> cdm2 TFTP Data block 9 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 9
cdm3 -> cdm2 TFTP Data block 10 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 10
cdm3 -> cdm2 TFTP Data block 11 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 11
cdm3 -> cdm2 TFTP Data block 12 (172 bytes) (last block)
cdm2 -> cdm3 TFTP Ack block 12
cdm2 -> BROADCAST DHCP/BOOTP DHCPDISCOVER
cdm2 -> BROADCAST DHCP/BOOTP DHCPDISCOVER
cdm3 -> cdm2 ICMP Echo request (ID: 48130 Sequence number: 0)
cdm3 -> cdm2 DHCP/BOOTP DHCPOFFER
cdm2 -> BROADCAST DHCP/BOOTP DHCPDISCOVER
cdm3 -> cdm2 ICMP Echo request (ID: 48130 Sequence number: 0)
cdm3 -> cdm2 DHCP/BOOTP DHCPOFFER
cdm2 -> BROADCAST DHCP/BOOTP DHCPDISCOVER
cdm3 -> cdm2 ICMP Echo request (ID: 48130 Sequence number: 0)
cdm3 -> cdm2 DHCP/BOOTP DHCPOFFER
And then fails: i.e. it seems not to find the boot image.
Any suggestions???
Lydia

The SUNWfoo and SUNWfoox packages were generally merged for Solaris 10 SPARC packages. The foox would represent 64-bit binaries/libraries and may be left out of a 32-bit system install.
Since Solaris 10 only runs a 64-bit kernel on SPARC, there's no reason to supply both packages and they were merged.
For x86, 32-bit kernel mode is still supported, and the package separation exists.
Darren

Similar Messages

Network install fron x86 solaris server to x86 solaris client ?

My setup is:
install server OS: Solaris 10, i86pc .
The install server is also boot server using tftpboot.
The dhpc server is configured according to the instructions which are
given when adding an install client in Solaris 10.
The client can communicate with the install and boot server but fails
to load the boot image. The snoop output is
Using device /dev/iprb0 (promiscuous mode)
cdm3 -> cdm2 ICMP Echo request (ID: 48130 Sequence number: 0)
cdm2 -> cdm3 TFTP Read "nbp.cdm2" (octet)
cdm3 -> cdm2 UDP D=2070 S=39122 LEN=22
cdm2 -> cdm3 TFTP Error: not defined
cdm2 -> cdm3 TFTP Read "nbp.cdm2" (octet)
cdm3 -> cdm2 UDP D=2071 S=39123 LEN=23
cdm2 -> cdm3 TFTP Ack block 0
cdm3 -> cdm2 TFTP Data block 1 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 1
cdm3 -> cdm2 TFTP Data block 2 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 2
cdm3 -> cdm2 TFTP Data block 3 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 3
cdm3 -> cdm2 TFTP Data block 4 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 4
cdm3 -> cdm2 TFTP Data block 5 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 5
cdm3 -> cdm2 TFTP Data block 6 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 6
cdm3 -> cdm2 TFTP Data block 7 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 7
cdm3 -> cdm2 TFTP Data block 8 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 8
cdm3 -> cdm2 TFTP Data block 9 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 9
cdm3 -> cdm2 TFTP Data block 10 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 10
cdm3 -> cdm2 TFTP Data block 11 (1456 bytes)
cdm2 -> cdm3 TFTP Ack block 11
cdm3 -> cdm2 TFTP Data block 12 (172 bytes) (last block)
cdm2 -> cdm3 TFTP Ack block 12
cdm2 -> BROADCAST DHCP/BOOTP DHCPDISCOVER
cdm2 -> BROADCAST DHCP/BOOTP DHCPDISCOVER
cdm3 -> cdm2 ICMP Echo request (ID: 48130 Sequence number: 0)
cdm3 -> cdm2 DHCP/BOOTP DHCPOFFER
cdm2 -> BROADCAST DHCP/BOOTP DHCPDISCOVER
cdm3 -> cdm2 ICMP Echo request (ID: 48130 Sequence number: 0)
cdm3 -> cdm2 DHCP/BOOTP DHCPOFFER
cdm2 -> BROADCAST DHCP/BOOTP DHCPDISCOVER
cdm3 -> cdm2 ICMP Echo request (ID: 48130 Sequence number: 0)
cdm3 -> cdm2 DHCP/BOOTP DHCPOFFER
And then fails: i.e. it seems not to find the boot image.
Any suggestions???
Lydia

I must have been too late previously. I got a whole host of output now.
The boot clearly tries to get underway, but configs fail, such as the real
boot file. I followed the instructions in the manual to setup the
dhcp server but must be missing something.
The output on the client is:
PXE BIOS stack - 8cc006e8
NBP ends at d108.
Buffer starts at d110.
Reserved memory starts at 8cc00.
Buffer size is 522992 bytes.
Checking !PXE structure at 9cf60070.
UNDIROMID c08000020, BaseROMID 0
StatusCallout 0
SegDesCnt 7, FirstSelector 0
Stack selector 8cc0, base 8cc00, size 800
UNDIDate slelector 96d9, base 96d90, size 61d0
UNDICode selector 9cf6 base 9cf690, size 2c40
UNDICodeWrite selector 9cf6, bse 9cf690, size 2c40
BC_Daate selector 8d40, base 8d400, size 3950
BC_Code slecttor 90d5, base 90d50, size 603e
BC_CodeWrite selector 90d5, bse 90d50, size 603e
Valid !PXE passed in by BIOS.
PXE is present
Calling PXENV_UNDI_GET_NIC_TYPE
Network boot dievice is PCI device 308, vendor ID 8060, device ID 1013
get_cached_info discover succeeded:
client IP: 0:0:0:0
your IP: 0:0:0:0
next server IP: 0:0:0:0
relay agent IP: 0:0:0:0
client MAC addr: 0:30:48:71:1c:44
server name:
boot file:
get_cache_info ack succeeded:
client IP: 0:0:0:0
your IP: 129.234.194.12
nextt server IP: 129.234.194.13
relay agent IP: 0:0:0:0
client MAC addr: 0:30:48:71:1c:44
server name:
boot file: nbp.cdm2
Network bootstrap program server was 129.234.194.13
Network bootstrap program file was nbp.cdm2.
get_cached_info reply succeeded:
client IP: 0:0:0:0
Your IP: 129.234.194.12
next server IP: 129.234.194:13
relay agent IP: 0:0:0:0
client MAC addr: 0:30:48:71:1c:44
server name:
boot file: nbp.cdm2
Calling PXENV_UNDI_GET_INFORMATION
client MAC address is 0:30:48:71:1c:44.
PXENV_UDP_OPEN succeeded
Broadcasting DHCPDISCOVER for class ID SUNW.i86pc.
PXENV_UDP_WRITE succeeded
PXEENV_UDP_READ failed, reet = 1, status =1
PXENV_UDP_READ failed, ret = 1, status = 1
When I checked access dates on files
in /tftpboot on the server I found that
nbp.cdm2 (the link) and nbp.I86PC.Solaris_10-1
had access times = time of boot attempt of client, but that
inetboot.I86PC.Solaris_10-1 had not been touched.
in the dhcp configuration there is no reference to inetboot.I86PC.Solaris_10-1 .
Any further ideas ?
Lydia

Can't install SJAS 8.2 in Solaris 10 x86 Zone

I'm using a VPS account from a vendor running Solaris 10 on one of Suns AMD machines.
I downloaded the sjsas_pe-8_2-solaris-i586.bin and uploaded it to the server.
I logged in as myselff and su'd to root.
I then chmod +x the .bin file and executed it.
This machine has Java 5 installed on it, in /usr/java.
It also has Java 1.4.2 in /usr/j2se.
I start the install, it asks for an installation directory (I choose the default of /opt/SUNWappserver), it creates the directory and then prompts for the JDK.
This is my transcript:
The Sun Java System Application Server Platform Edition components will be
installed in the following directory, which is referred to as the "Installation
Directory".To use this directory, press only the Enter key. To use a different
directory, type in the full path of the directory to use followed by pressing
the Enter key.
   Installation Directory [/opt/SUNWappserver] {"<" goes back, "!" exits}:
The Sun Java System Application Server requires a Java 2 SDK.
   Please provide the path to a Java 2 SDK 1.4.1 or greater.
   Recommended version is 1.4.2 or greater. [/usr/j2se] {"<" goes back, "!"
   exits}At this point I just hit enter to accept the default (/usr/j2se) and the installation just hangs. It also hanged when I told it to use /usr/java.
I ran: truss -f -o /tmp/out ./sjsas_pe-8_2-solaris-i586.bin -console
And in another window saw that it was essentially idle.
12955/8:        pollsys(0xBD1BBEA0, 0, 0xBD1BBEF8, 0x00000000) = 0
12955/8:        pollsys(0xBD1BBEA0, 0, 0xBD1BBEF8, 0x00000000) = 0
12955/8:        pollsys(0xBD1BBEA0, 0, 0xBD1BBEF8, 0x00000000) = 0
12955/8:        pollsys(0xBD1BBEA0, 0, 0xBD1BBEF8, 0x00000000) = 0
12955/8:        pollsys(0xBD1BBEA0, 0, 0xBD1BBEF8, 0x00000000) = 0
12955/2:        lwp_cond_wait(0x08072FE0, 0x08072FC8, 0xBAE9AE68, 0) Err#62 ETIME
12955/8:        pollsys(0xBD1BBEA0, 0, 0xBD1BBEF8, 0x00000000) = 0
12955/8:        pollsys(0xBD1BBEA0, 0, 0xBD1BBEF8, 0x00000000) = 0
12955/8:        pollsys(0xBD1BBEA0, 0, 0xBD1BBEF8, 0x00000000) = 0
12955/8:        pollsys(0xBD1BBEA0, 0, 0xBD1BBEF8, 0x00000000) = 0
12955/8:        pollsys(0xBD1BBEA0, 0, 0xBD1BBEF8, 0x00000000) = 0
12955/8:        pollsys(0xBD1BBEA0, 0, 0xBD1BBEF8, 0x00000000) = 0
12955/8:        pollsys(0xBD1BBEA0, 0, 0xBD1BBEF8, 0x00000000) = 0
12955/8:        pollsys(0xBD1BBEA0, 0, 0xBD1BBEF8, 0x00000000) = 0Any ideas why this is happening? Could this be something to do with the Zone?

So, if I understand this correctly, you are running this installation in local zone and trying to use J2SE from the global zone, right?
This hang might have something to do with zones. Based on limited truss snippet it is hard to tell where exactly it hangs, though. One possibility is that in fact J2SE verification went through fine but the next screen is the one which asks for default server configuration, including port numbers. Before that screen is shown, installer will try to find out whether the default port numbers are free or not, so it is possible it actually hangs there.
To see if the port verification is an issue, please try running:
./sjsas_pe-8_2-solaris-i586.bin -console -noportcheck
With this option, any port verification done by installer will be skipped, so if the hang was there installation should now go through. Note that this will create your default domain using default set of port numbers, so there is a chance you'll need to change port values prior to starting the server if any of those ports are in fact in use.
Also, if installer hangs in port verification, this might point to network configuration issues, so if you also run into problems during the server startup you might need to further deal with networking. In any case, try installing as above and see if you can get further.

64-Bit PHP on x86-Solaris 11.1

Hi all,
we have just set-up a x86-Solaris 11.1 based workgroup server which will be mainly used for web-based applications (like ownCloud, Moodle or openAtrium) at our university institute. As some of the members of our workgroup produce media (i.e. full HD videos), we have to deal with files larger than 2 GB. While it isn't any problem for Solaris' Apache to handle these file sizes, some PHP applications have quite big problems to work with files >2 GB correctly as long as the underlying PHP is a 32 bit binary.
I wouldn't have expected that an Enterprise system like Solaris 11.1 still comes with 32 bit applications as the Solaris kernel itself is using the 64 bit mode on x86_64 for quite some time now. Nevertheless, as I really like Solaris' features especially for stable and large storage solutions, I want to stick with Solaris and will have to find a solution for the mentioned problem...
Recompiling PHP from the sources as a 64 bit application is not a problem. I also assume that I would also have to recompile Apache2 as a 64 bit application to get compatibility to the apache module of 64 bit PHP.
My question is: Is there any "gold standard" to accomplish this? Of course, I can recompile all parts that I need by myself, completely independently from the packaging system, and put them to "/usr/local/..." or to "/opt/local/...". I am, however, not sure if this is the best way. Perhaps there are already packages I could install and I don't know about. I can't imagine that I am the first user who experiences that problem. Would it make sense to switch to an alternative package repository like OpenCSW? What I also thought about, was the following way to proceed: I'm going to take the source packages from Oracle and then compile Apache and PHP (and most probably also MySQL) with the option for 64 bit according to the instructions in the sources. So I can also build new packages which I can deploy into the zones where I need them in.
Is there any better way which I might have overlooked, yet?
Thank you in advance for any help!
Kind regards,
Steffen

I also assume that I would also have to recompile Apache2 as a 64 bit application to get compatibility to the apache module of 64 bit PHP. In S11.1 Apache is already 64-bit aware:
ls -l /usr/apache2/2.2/bin/amd64
total 4277
-r-xr-xr-x 1 root bin 89584 Jan 12 20:47 ab
-r-xr-xr-x 1 root bin 3649 Jul 19 2012 apachectl
-r-xr-xr-x 1 root bin 22657 Jul 19 2012 apxs
-r-xr-xr-x 1 root bin 16424 Jan 12 20:47 checkgid
-r-xr-xr-x 1 root bin 8925 Jul 19 2012 dbmmanage
-r-xr-xr-x 1 root bin 1348 Jan 12 20:47 envvars
-r-xr-xr-x 1 root bin 1081 Jan 12 20:47 envvars-std
-r-xr-xr-x 1 root bin 36728 Jan 12 20:47 htcacheclean
-r-xr-xr-x 1 root bin 27232 Jan 12 20:47 htdbm
-r-xr-xr-x 1 root bin 21616 Jan 12 20:47 htdigest
-r-xr-xr-x 1 root bin 26432 Jan 12 20:47 htpasswd
-r-xr-xr-x 1 root bin 841064 Jan 12 20:47 httpd
-r-xr-xr-x 1 root bin 859224 Jan 12 20:47 httpd.worker
-r-xr-xr-x 1 root bin 21576 Jan 12 20:47 httxt2dbm
-r-xr-xr-x 1 root bin 17376 Jan 12 20:47 logresolve
-r-xr-xr-x 1 root bin 21464 Jan 12 20:47 rotatelogs
-r-x------ 1 root bin 21712 Jan 12 20:47 suexec.disabled
The problem is that 64-bit PHP isn't bundled.
You can try to rise an SR on that topic.
It seems that it would be easier to integrate large file support only in 32-bit PHP instead.
Any 32-bit application that is compiled with large file support (-D_LARGEFILE_SOURCE and
-D_FILE_OFFSET_BITS=64) will work with > 2GB files.
I think that SR could be realized relatively faster than integrating stable 64-bit PHP.
Regards,
Serghei

Moving disks while maintaining Solaris 10 install from one v240 to another.

Hi,
I want to move a Solaris 10 install from a sunfire v240
with a single cpu to another sunfire v240 with dual cpu's. Here are the
details of the hosts as well as configuration.
I have 2 sunfire v240's. One has a single 1 Ghz cpu and the second has
dual 1.5 Ghz cpu. I want to move the disks of the single cpu host to
the host with dual cpu's. I want to keep the installed version of
Solaris 10 intact. The installation of Solaris is split across 2
mirrored disks, i.e. 4 disks in total. I am using Suns volume manager
for mirroring and also have one files system mirrored with zfs.
The questions I have are the following:
1) Can I simply shut down the servers and swap the disks to the
destination host, in the same disk slots? The controllers the disks are
on line up and are the same between the 2 hosts.
2) Will the kernel pickup the changes moving from a single 1 Ghz cpu to
dual 1.5. Ghz cpu's with out any problems? Will the kernel pickup the
faster cpu's speeds. i.e. will it know it is now running dual 1.5. Ghz
cpu opposed to a single 1 Ghz?
3) Would we have to break the mirroring on the OS before shutting it
down?
4) As another option, instead of swapping disks, could we swap the
cpus? Move the dual 1.5. Ghz cpu's to the other host? Will the
motherboards read the updates of the cpu or are their jumper settings we
would need to update?
Thanks for your help.

Box A
Sparc Solaris 9, Oracle 10g
Box B
Solaris 10 x86, Oracle 11g
I know there are many factors, but I'm pretty new to both unix & oracle, so I >needed some general steps to get me started. You have many options.
Since you're in 10g, Have the Target Database created in Solaris 10 x86, Oracle 11g.
you can use,
RMAN - Cross platform Transportable Tablespaces.
Datapump Export and Datapump import.
Read the following:
How To Use RMAN CONVERT DATABASE for Cross Platform Migration - 413586.1
http://download-uk.oracle.com/docs/cd/B19306_01/backup.102/b14191/dbxptrn.htm
http://www.oracle-base.com/articles/10g/OracleDataPump10g.php
http://www.oracle-base.com/articles/10g/RMANEnhancements10g.php#cross_platform_tablespace_conversion

Solaris v10 sparc jumpstart server on x86 solaris - can't find miniroot.

I am trying to setup a jumpstart install server on an x86 solaris v10 machine to do a sparc network install. I downloaded both the CD and DVD sparc v10 ISO's. When I mount the CD, the Solaris_10/Tools/Boot directory (miniroot system) is symlinked back to ../../../s1 which does exist. I can't find it on the CD, I've used prtvtoc and this slice does not seem to exist.
On the DVD iso, the directoy exists, but many files cannot be read, almost like the filesystem is corrupt.
I've download these ISO and burned them many times, so I know it's not an issue with hardware or the CD/DVD media.
Where can I download a working sparc solaris v10 miniroot system?

There is no such entry under solaris. This entry only exist on windows.
On solaris you need to change entries in the kjs script (prior to SP3)
or iasenv.ksh (after SP3)
madhavi korupolu wrote:
>
Can anybody tell me why the entry for /Application Server/6.0/Java/ in
kregedit on solaris is missing. I have the entry upto /Application
Server/6.0/.
Try our New Web Based Forum at http://softwareforum.sun.com
Includes Access to our Product Knowledge Base!--
Han-Dat Luc ([email protected])
Senior Consultant
SUN Professional Services (iPlanet)
o .
o .
O _ ____ _ _
(_) _ \| | __ _ _ __ ___| |_ TM
| | |_) | |/ _` | '_ \ / _ \ __|
| | __/| | (_| | | | | __/ |_
|_|_| |_|\__,_|_| |_|\___|\__|
e-commerce solutions
Sun Microsystems Australia Pty Ltd

X86 Solaris 10 problems with ipfilter

Colleagues,
I'm install Solaris 10 on HP Proliant DL360 G4
(listed in HCL for Solaris OS http://www.sun.com/bigadmin/hcl/data/sol/systems/details/691.html)
Everything works fine till, but when I increase loading
(DNS server there, so too much UDP packets, about 2000/sec) Solaris panic with:
Nov 30 10:35:45 d0 ^Mpanic[cpu0]/thread=ffffffff85759820:
Nov 30 10:35:45 d0 genunix: [ID 103648 kern.notice] mutex_exit: not owner, lp=0 owner=0 thread=ffffffff85759820
Nov 30 10:35:46 d0 unix: [ID 100000 kern.notice]
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08190 unix:mutex_panic+6f (0, ffffffff860f5d98, fffffe)
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c081b0 unix:mutex_vector_exit+39 ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c081e0 ipf:ipf_stinsert+333e9215 ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08210 ipf:fr_updatestate+61 ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08250 ipf:fr_checkstate+10f ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08390 ipf:fr_check+629 ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08530 pfil:pfil_precheck+850 ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08560 pfil:pfilmodwput+9f ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c085c0 unix:putnext+1f1 ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c086d0 ip:ip_wput_ire+1a98 ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08780 ip:ip_output+ee9 ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08790 ip:ip_wput+18 ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c087f0 unix:putnext+1f1 ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08870 udp:udp_wput+29d ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c088d0 unix:putnext+1f1 ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08a70 genunix:strput+3bc ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08af0 genunix:kstrputmsg+1e8 ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08ba0 sockfs:sosend_dgram+181 ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08c10 sockfs:sotpi_sendmsg+1bc ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08c80 sockfs:sendit+f0 ()
Nov 30 10:35:46 d0 genunix: [ID 655072 kern.notice] fffffe8000c08ed0 sockfs:sendmsg+1bf ()
Nov 30 10:35:47 d0 unix: [ID 100000 kern.notice]
Nov 30 10:35:47 d0 genunix: [ID 672855 kern.notice] syncing file systems...
Nov 30 10:35:47 d0 genunix: [ID 733762 kern.notice] 34
Nov 30 10:35:48 d0 genunix: [ID 733762 kern.notice] 24
Nov 30 10:36:08 d0 last message repeated 20 times
Nov 30 10:36:09 d0 genunix: [ID 622722 kern.notice] done (not all i/o completed)
Nov 30 10:37:30 d0 genunix: [ID 540533 kern.notice] ^MSunOS Release 5.10 Version Generic_118844-20 64-bit
Nov 30 10:37:30 d0 genunix: [ID 943906 kern.notice] Copyright 1983-2005 Sun Microsystems, Inc. All rights reserved.
At some stage there are problems with creation of a new state...
I remember some time ago (Solaris 2.8) there where problems like that with ipfilter, but now ipfilter included in Solaris distribution, hardware tested and so on...
New reincarnation of a problem?
Somebody has similar problems with the software x86 Solaris 10?
Thanks, Roman Gnatenko (rvg at co.ru)

Hi. I've never seen anything like this, and it seems to be something which
the JDBC module is going to be an innocent victim of, rather than a
contributor to... Your best course is to open an official support case.
Joe

I am having a problem installing the x86 drivers on a Windows 2008 server for a hp 4000n.

I am having a problem installing the x86 drivers on a Windows 2008 server for a hp laserjet 4000n.

Hi all,
Sylonious, did you manage to sort this problem out? I have been experiencing similar problems. I think my problem was because I had many different versions of JDKs. I have done a complete re-install. I would be really grateful to you (and anyone else) for help with this problem.
I have re-installed JSDK1.4.2_03, set the "path" variable to "C:\JSDK1.4.2_03".
When I compile using "javac" I get an error saying "javac" is not recognised.
When I compile using "C:\j2sdk1.4.2_03\bin\javac Freq.java" no error is thrown.
Every time I try to run a java file, I always get the NoClassDefFound error. When run with the -verbose option, files are loaded from C:\Program Files\Java\j2re1.4.2_03\bin - is this correct?
I have removed all previous references to java in the registry editor.
Please help !
Regards,
Vipul

How can x86 Solaris detect a expanded SAN volume

I have a x86 solaris box (SunOS jdnm01cdr01s 5.10 Generic_137112-02 i86pc i386 i86pc) that connects to a SAN volume with initial 10G space.
I increases the volumn size to 20GB.
Format commands displays the name is updated to 20G.
AVAILABLE DISK SELECTIONS:
       0. c0t600A0B800039BE61000016894ACD4D2Ad0 <SUN-LCSM100_F-0617-20.00GB>
          /scsi_vhci/disk@g600a0b800039be61000016894acd4d2aHowever, the partition tool is still report the wrong size.
Current partition table (original):
Total disk sectors available: 20955101 + 16384 (reserved sectors)
Part      Tag    Flag     First Sector        Size        Last Sector
0        usr    wm                34       9.99GB         20955101
1 unassigned    wm                 0          0              0
2 unassigned    wm                 0          0              0
3 unassigned    wm                 0          0              0
4 unassigned    wm                 0          0              0
5 unassigned    wm                 0          0              0
6 unassigned    wm                 0          0              0
8   reserved    wm          20955102       8.00MB         20971485
format> label
Ready to label disk, continue? yes
partition> p
Current partition table (original):
Total disk sectors available: 20955101 + 16384 (reserved sectors)
Part      Tag    Flag     First Sector        Size        Last Sector
0        usr    wm                34       9.99GB         20955101
1 unassigned    wm                 0          0              0
2 unassigned    wm                 0          0              0
3 unassigned    wm                 0          0              0
4 unassigned    wm                 0          0              0
5 unassigned    wm                 0          0              0
6 unassigned    wm                 0          0              0
8   reserved    wm          20955102       8.00MB         20971485How does it detect the new size?

The disk is running in ZFS and has data on it.
Does it harmful if I modify the VTOC label?
I get the following from the server. Shall I extend the slice up to 41943039?
# prtvtoc /dev/rdsk/c0t600A0B800039BE61000016894ACD4D2Ad0s2
* /dev/rdsk/c0t600A0B800039BE61000016894ACD4D2Ad0s2 partition map
* Dimensions:
*     512 bytes/sector
* 41943039 sectors
* 20971452 accessible sectors
* Flags:
*   1: unmountable
* 10: read-only
*                          First     Sector    Last
* Partition Tag Flags    Sector     Count    Sector Mount Directory
       0      4    00         34 20955068 20955101
       8     11    00   20955102     16384 20971485

Migrate an application from x86 to x64. Compiling succeed, but can not run. Always start with error 0xc0000142.

platform: windows server 2008 r2; ide: visual studio 2005 (installed the x64 development kit)
Hi, everyone.
I want to migrate my application to x64 platform from x86/win32 platform. I added x64 platform in visual c++ 2005 option, and compiled successfully. But the application can not start. When start it always pop up an alert dialog saying "The application
was unable to start correctly (0xc0000142). Click OK to close the application." Meanwhile, it's worked well when I use win32 option to compile.
Someone says online, the dependency walker can detect some root cause. I used it, and found that IEFRAME.dll may be had some problem because when I double click it, pop up a dialogue saying "Errors were detected when processing "c:\windows\system32\IEFRAME.DLL".
See the log window for details.". But I can not resolve this issue.
Please help me.

If I had to try to solve this:
I'd start by verifying that I can compile, and run a skeleton x64 Windows app. Just create one from scratch using the Windows Application project template, add the x64 platform, build it and run. Hopefully all goes well.
If that works, then I'd try trimming down your app to just its essentials. If you're not using revision control software, back up your projects now, because once you find the problem by hacking and slashing, you'll want to revert so you can make a
clean fix.
The first thing to do here is just put a return 0; in the beginning of WinMain to see if it's code at runtime that's causing the problem or something about the linking and dependent library loading.
I'm guessing that, even with return 0, you will still have a problem, which would suggest that you are perhaps still linking against a 32-bit version of a library or something like that. Start removing dependencies or references or libraries until
you can build and run your stripped-down application. Eventually you'll find the one reference/library that causes it to fail to load.
You can also check the debug window to see if some modules loaded correctly and others not.
You can also run
Process Monitor (sysinternals) to see which dll it was accessing when it failed to load.
Make sure you revert any changes you made while hacking and slashing, then make your platform fixes, and have another go.
I suspect that eventually you'll find that you've added a link library that is a 32-bit .lib or a component that references a 32-bit library. You'll have to make sure you specify the x64 .libs for whatever libraries you are using. Sometimes this
means that you have to change you additional linker directories to point to the x64 libs instead of the x86/win32 libs. Be very careful about your platform when specifying linker libraries, directories, etc.
It could also be that the x64 version of a dll has been copied to your output folder rather than the x86 version, assuming they have the same name. You'll have to sort out your SDKs and get the right .libs and .dlls.
Make sure that your settings and property pages are set correctly for Release and Debug, and for x86 and x64.

Does "rpm" exist for x86 Solaris 10 ?

Does "rpm" ( the Red Hat Package Manager ) exist for x86 Solaris 10 ? I haven't found it on www.sunfreeware.com or by Googling, and rolling my own is getting nasty....
Thanks !

there is a rpm2cpio command in Solaris, which is useful if you have source code or similar distributed in a RPM package format, but for Solaris installations you have pkgadd/pkgrm, and then there is the pkg-get utility which is downloadable from blastwave.org .
.7/M.

Link to download X86 Solaris Installation for weblogic 10.3

Can please anyone let me know the link to download X86 Solaris Installation for weblogic 10.3.
I am only able to see installables for X86 windows,X86 linus & sparc but nothing for X86 Solaris.

Hi;
Can please anyone let me know the link to download X86 Solaris Installation for weblogic 10.3.I belive its not available. Please check :
WebLogic 10.3 availability?
Also check certification matrix:
http://www.oracle.com/technology/support/metalink/index.html
Regard
Helios

How to install from a Solaris 8 install .iso?

I want to try to install Solaris 8 in an LDOM. I know that it is "not supported" - but it may be possible, according to some discussions I have had, so I want to try.
Unfortunately, when I try the naive approach and add the iso image of the CD as a virtual disk to the domain and try to boot from it, it tells me the file isn't executable. The explanation, it seems, is that the CD actually contains several slices, and only the first one is visible when you look at it as an iso file. So, I guess my question is: Is it actually possible to get to a point where I can try to install from this CD image into an LDOM?

Well, if it was supported you would be able to ;)
The thing with the SPARC installation CD's is that they are indeed sliced, i think the reason for it to be sliced is that different slices supports different CPU architectures, so that slice 2 (or slice :b when you boot it from an OK prompt) was originally, long time ago, used for the sun4c CPU's, slice 3 (or :c) was used for sun4m and slice 4 (:d) was used for sun4d.
Then came sun4u which used slice 5/:e
Then slice 0 would contain a HSFS filesystem which actually contained the packages and the installation program.
You can get the vtoc with dd, and then extract the slices you want with dd and access them using LOFS. But yet again this is probably futile. I don't think there is a single chip in the T4 hardware which is supported with Solaris 8.
Given how powerful the T4 seems, and how ineffective Solaris 8 could sometimes be at utilizing resources, it would also seem like a waste..
Have you had a look at native zones? that way you can run Solaris 8 / 9 in zones under Solaris 10..
.7/M.

How can I install Oracle Database 10g for Solaries (SPARC) from the console

Dear Forum Members,
In my office, I have to installed Oracle Database 10g for Solaries (SPARC). But I have to do it without DISPLAY Monitor.Is it possible install it by remote login to this server using response file (silent mode) or something like that?
If yes. Then How?
If anyone have the exact solution, then I need your feedback. I shall wait for your reply.
Thanks
Aungshuman Paul

There are 2 possible ways to accomplish this.
First,
Silent installation
http://www.informit.com/articles/article.asp?p=174771&rl=1
Second, (cut/paste from other site)
How to install Oracle software remotely?
Remote Software Installation Steps: (For Solaris only)
If you want to install Oracle Software remotely, you should perform the following steps. These steps are applicable only if your source and target machine are running Unix.
For example, you can install Oracle Software from your home from Washington, DC to a target source in California.
1. Pick your source server or machine for remote installation.
2. Check that your CD is in your source CD-ROM drive.
3. On the target machine, find your target machine name with the output of the /usr/bin/hostname
4. On the source machine, login as a user.
5. On the source machine, enable client access: % /usr/openwin/bin/xhost + target-machine-name
6. Become root user by typing: su (dont use -)
7. Check that Volume Manger is running. # ps ef |grep vold (if you see an entry that contains /usr/sbin/vold, Volume Manager is running. Then skip to Step 10.
8. If not then do the following: # mkdir p /cdrom/your-cd-file-name
9. # mount F hsfs r cdrom-device /cdrom/your-cd-file-name
10. Add the following line to your /etc/dfs/dfstab file: # share F nfs o ro /cdrom/your-cd-file-name
11. Verify whether your source machine is an NFS server: # ps ef | grep nfsd
12. If you see an entry that contains /use/lib/nfs/nfsd a 16, then nfsd is running and skip to Step 16.
13. If nfsd is running, then type: # /usr/sbin/shareall
14. If nfsd is not running, then start nfsd by typing: # /etc/init.d/nfs.server start
15. Verify whether your source machine is an NFS server again by typing: # ps ef | grep nfsd
16. Make sure your source machine is exporting your product directory by typing: # /usr/sbin/dfshares
17. Now, log in to the target machine by type: # rlogin target-machine-name l user (not root)
18. Then log in as the root user by typing: # su
19. Go to the source machine by typing: # cd /net/source-machine/cdrom/your-cd-file-name ,then Skip to 24.
20. If you cannot change to that directory in Step 19 and you do not have an auto-mounter on your network, then create amount point by typing the following commands.
21. # mkdir /remote_products
22. # /usr/sbin/mount F nfs r source-machine:/cdrom/your-cd-file-name /remote_products
23. # cd /remote_products
24. Redirect the target machine display to source machine by typing: # DISPLAY=source-machine:0; export DISPLAY (if you use a Bourne or Korn shell).
25. Start the Web Start Installer by typing: # ./installer (or whatever the installer name program is).

SWTK for x86 Solaris

Hi all,
Is there a beta version of SWTK for x86 Solaris or it's anchored to Windows or Linux development platform?
Thanks in advance,
Pedro
P.D.: Linux's version works a little at my opensolaris box but without preverify or zayit, and the emulator shutdowns early.

Jason Roesler wrote:
II am interested to know,
Is there an native client for enterprise eddition or enterprise 3 for
Solaris x86?
thanks
Hi.
There should be in the upcoming 4.1 release of SGD EE.
Native Clients should be available for Windows, Linux (Intel x86), Sparc
Solaris, x86 Solaris, MAC OS/X.
Best,
Rob
Roberto Zini - r.zini<@AT@>strhold.it
"Has anybody around here seen an aircraft carrier?"
(Pete "Maverick" Mitchell - Top Gun)

Jumstart install from x86 to x86 Solaris 10

Similar Messages

Maybe you are looking for