Just got my RMAed MB(K8T NEO2-F) back GOING GOOD@264FSB

CAN SOME PLEASE HELP!!!! I sent my old MB (K8T NEO2-F) in because I could not get the MB to reboot into Windows after setting AGP Frequency to 66Mhz. So now I just put the system back together with the MB they sent me and was going to try and OC this 3200+ I have but I put the AGP Frequency to 66Mhz and it would not boot into windows still. Am i missing something here or what? I am supposed to set the AGP Frequenct to 66Mhz to keep my SATA Raid locked right? There are 3 settings 1-Sync with CPU 2-66Mhz and 3-75.4Mhz. Now how can I OC this board this way? That is what I'm supposed to use to lock it right? Is there a special way I'm supposed to do it? I just went in and disabled spread spectrum set FSB to 210 set AGP Frequency to 66Mhz Lowered HHT from 1000 to 800 then saved and it didn't reboot. So I reset the BIOS went in set spread spectrum to disabled set FSB to 215 and set HTT from 1000 to 800 saved and it booted into windows. So the 66Mhz isn't letting this MB boot either. Plus for the CPU VCORE it is set on AUTO and there are no other settings except for AUTO for it.

Guys that is way outdated info on those links and not for this board with the newer CPU's Ignore it.
The K8T800 is a socket 754 board and has no AGP locking. This can't be fixed as Via has an issue with that chipset and that is where the problem is not in the Bios.
The K8T800 Pro is the socket 939 board but you must use 9.x for any of the newer CPUs beyond Clawhammers, Newcastles and Winchesters. These have locking that works and can be confirmed. However there has been a couple reports of ATi cards that don't lock using this board.
The X2's and the Opties must use socket 9.3 to operate correctly.
There have been a couple folks now with ATi 9xxx cards that have reported troubles with the locking on the Neo2 boards. No idea what will fix it as there was never enough complaints to isolate the problems and I am still trying to gather enough data on it. Some ATi 9xxx cards work and some don't I do not have enough info to check further.
The only thing I can tell you is to report the issue to MSI who may or may not be able to sort it out. Again there is very little info on this particular problem.
There are no modded Bios's for that board that I have found. Yes I looked. I am not sure a modded Bios would solve this anyways unless there was more info on what the cause is. You need to know more than one or two cards won't lock. Most cards do lock and everything is fine. So there has to be something odd about those cards that don't that is different from the rest that causes this. However I don't have that info so even passing this on helps veryu little.
I am still gathering data but as there are fewer and fewer folks that have the right combo of parts that show the problem there is likely not going to be enough data to finds the problem.

Similar Messages

I just got myself a macbook how do I back it up

I just got myself a macbook and learning how to use it not sure how back it up I'd switched it on but when I close it's off again I manage to put my printers drive inside the window can anyone help I have time machine I hear you guys talk about boot camp what's that.

A laptop will going to sleep mode when you close it because it would overheat if it was left running with the lid closed.
The best way to back up your Mac is to get an external hard disk and use Time Machine. You can set this up from System Preferences. Click the question mark button at bottom right of the preference pane for more information.
You could also get a second external hard disk and clone your Mac to it; you can do this using Disk Utility in Applications/Utilities, or third party programs such as SuperDuper. The advantage of this is that you get an exact copy of your Mac which you can start up from in an emergency.
Boot Camp is nothing to do with backing up. It is a method of running Windows on your Mac.

I just got a macbook pro Retina display , where is a good resourse on how to use it ?

Hi all ,
never owned a mac before and know nothing about it.
Where is a good resource on using it , like a really good
users manual ? Like how do I use the turbo boost on it ?
Im good on a pc but lord , please help me. Id sure appreciate it.
Either that or sell the thing . thanks for looking

You might want to check Amazon and search for a "Mavericks Missing Manual" - they are usually very good informative manuals, though not necessarily good for the actual hardware of your computer. Knowing the OS, though, is far better than any sort of hardware manual.
As to making a recovery disk, you can get a 8GB+ USB pen drive and, having downloaded "Install OS Mavericks.app" from the Mac App Store, create a USB recovery pen drive using DiskMaker X to create the USB drive. Pretty simple. I don't know that you can use a DVD any longer (you once could but I don't know any longer).
Clinton
MacBook Pro (15-inch Late 2011), OS Mavericks 10.9.4, 16GB Crucial RAM, Crucial M500 960GB SSD, 27” Apple Thunderbolt Display

Just got an iPhone 5s a few weeks back and it restarts!

My new IPhone 5s has suddenly restarted 3 times in a week and is currently taking long to turn on when I press the home button. What do I do? I have also never dropped it or damaged it in any way.

Did you set up this phone from a backup of your old phone? You can try restoring the phone as a new device, not from a backup and manually sync your content back. See if that helps, or you can make a backup of the device, make an appointment at the Genius Bar and have the hardware checked.

I just got a connect to iTunes icon while backing up my iPad. I have reset it. No luck. HELP!

I have reset several times and restarted my computer.

You will have to be more specific. Why have you reset it (presumably the iPad)?

MSI K8T Neo2 constant hangup

OK, so I changed my motherboard a few days ago, and got myself a MSI K8T Neo2 card, with the AMI bios ver.3.31a
I put in my old 2 x Apacher 256mb pc 2700 ram (single side) in there, and tried to add in some other ram, but it failed.
I also got my 350powersupply running on it. (It says 5v, 3.3v and 12v on the side, saw someone asking about that in another tread, if that helps)
So now I get to boot all the way into windows (XP SP2 btw), and I even get it running for a long while (sometimes)
Like last night, it was up all night doing recovery from a old HD, that took 7-8hours, and no brakedown.
However, when I try to do normal things... like open a folder, there is a 1 in 20 chance (about) that it will hang.. Same with watching a movie, while watching it will just hang.
So when starting a program/task, running a program/task, ending a program/task. There is always a chance of frezzing up.
Anyone got any idea of what the problem is?

35A, 28A, 17A, 0.3A, 0.8A, 2A
I'w been thinking about a ram problem, seeing how the ram is old, and most people complain over the fact that Ram prevents booting (not a problem) and makes the system unstable (just my problem).
Video driver/card problem never crossed my mind.. it's nvidia.. the most streamline drivers out there.
There is no cpu drain, and no apps that are not responding. I have been having this problem all the way since I did a clean install of windows, so I don't think it's a program problem.
However.. I found the first sign of "always" crash last night.
If I wanted to play Evil Genius, and I had a file application started, (emule or Ares) It would hang before it could load up, always. If I had them turned of, then it would have a far bigger chance of starting and running normaly.

I have just got an Airport time Capsule for back up how do I do it? Do I put the ethernet cable into the back of my sky hub because when I do that the amber light on my Time Capsule flashes amber. Please talk in simple terms as I am a

I have just got an Apple Airport time capsule to back up my one year old iMac......how do I do it? I have tried putting an ethernet cable into the time capsule and to my sky hub, all I get is a flashing amber light, can anyone help I am a silver surfer not used to Apple products, but love them, plus I don't understand half of the jargon....HELP please

Apple's Setup Guide for the Time Capsule is pretty simple and clear for most users, and you don't indicate at what point or step that you are getting stuck.
So, please go to page 8 in your Setup Guide to review the topic of Plugging In Your AirPort Time Capsule.
The Sky hub will likely have 4 Ethernet <--> ports on the back of the device. Pick any one that you want and connect one end of the Ethernet cable to the port that you choose.
Then, connect the other end of the Ethernet cable to the WAN (circle of dots) port as shown in the Setup Guide.
Continuing with the instructions on page 8 of the Setup Guide, power up the Time Capsule by connecting the power cord from the back of the Time Capsule to a wall AC jack.
Note that the instructions indicate that the indicator light will be solid amber during startup, and it will change to blinking amber during the setup. The light will remain blinking amber until you have configured the Time Capsule at which time the light will turn green.
Next, go to page 12 of the Setup Guide to see the information to Use your Mac or iOS device to set up your AirPort Time Capsule.
You indicated in your tag line that you were using OS X Mountain Lion (10.8.3), and since that will exceed the minimum requirement of a Mac using OS X (10.7.5) as noted in the guide, you can use your Mac to set up the Time Capsule.
Continuing with the instructions on page 12 of the Setup Guide......
1. Open AirPort Utility on your Mac. It is located as follows: Finder (the smiley face on the dock) > Applications > Utilities > AirPort Utility
2. Select your AirPort Time Capsule and click Continue. You won't be able to do this, but read further......If you do not see the AirPort Time Capsule that you want to configure, choose it from the WiFi status menu in the menu bar, at the top of the screen.
So, clicking on the WiFi icon will yield a small window that looks like this:
The example below shows an AirPort Extreme. You will see Time Capsule on your screen. Click on Time Capsule.
When you click on Time Capsule, that will get the setup wizard going. it will take a minute to analyze the network, then display a screen that looks similar to the illustration below, except that you will see a picture of a Time Capsule on your screen
3. Continuing with the Setup Guide.......Follow the onscreen prompts to create a new network
Network Name...........Type in a simple name that you want to call your network. Do not use the suggested name.
Base Station Name....Type in a simple name that you want to call the Time Capsule. Mine is TC, for example.
Password...................Type in a password that will be used for both the network and the Time Capsule. Write that down.
Verify..........................Type in the password again to Verify
Click Next
The setup wizard will configure everything for you. When you see the message of Setup Complete, click Done.
The Time Capsule is now set up and it will display a green light.

Just got my iPhone 5s at&t out of a blue screen boot loop how do i prevent this in the future?

My sister has had her iphone 5s at&t for a while. While using it would get stuck on the apple logo but would usually reboot and be fine within a minute. Today i just got stuck there and didn't go back to normal, so i decided to completely restore it (7.1.0) and after 10 tries of pluggin the usb in different ports and putting it in dfu and restore mode i finally got it to work. (9 of those tries it finished the restore then went into a blue screen and proceeded to show an apple logo with a loading bar that wouldn't move). Now i'm just holding on to it and probably going to take it to the apple store to get it replaced but it has no warrenty and im not prepared to pay 200 or more for a phone thats in perfect condition without a scratch(kidda stupid to charge a flat rate for every problem i understand if the phones glass is broken but for os problems). So is there any options i have rather than taking it to apple to stop this problem from happening.

OS X Yosemite: Use your Mac to make and receive phone calls

I recently got a new iphone 5s and accidentally backed it up with my old iphone. I lost all my pictures. Is there anyway for me to get my pictures back?

I had previously had an iphone5 but it got stolen and I just got the iphone5s. I had previously backed up my old iphone to my itunes, and didnt have time to restore it to my new phone. I had taken pictures with my new iphone and when i connected it to my laptop i changed the setting to backup with icloud and it deleted all my current pictures and things and replaced them with what was on my old phone. Is there anyway I can undo this and get my pictures back?

Almost certainly you lost the previous iPhone 5S photos. But just in case you might have saved them ...
On your iPhone 5S, check Settings > iCloud > Storage & Backup and find the time (if any) that you made an iCloud backup. If you made one before you deleted the iPhone 5S' photos, they are on iCloud. If that's the case, you can retrieve them by doing Settings > General > Reset > Erase All Content and Settings and then restoring that iCloud backup to the iPhone. Of course, you would then lose the iPhone 5's photos from the iPhone 5S.
It's extremely unlikely you performed this iCloud backup at the right time, but it's your only chance.

Just got my K7T Turbo2 from RMA. Ver 5 ??

Topic says it ..
How can I tell if the K7T Turbo2 I just got back from rma is a ver 5 ?? 2600xp t-bred (a) support would be great !
T

if its a turbo 2 its version 5
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=24&MODEL=MS-6330

[865PE/G Neo2 Series] Just got my first SATA drive.. need help booting up.. :(

Hey guys
I just got my very first SATA drive. it's a Hitachi 160GB 7k250!
anyway, I wanted to set this new drive (partion 1 to be exact) as my PRIMARY or what I like to call SYSTEM drive.. this is where i store only my windows core files and program files..
My previous setup is that I have 2 PATA drives (Primary master and Secondary Master) and 2 DVD drives (Primary Slave and Secondary Slave)..
Now with the introduction of this new SATA drive, well, i didnt know what to do..
I got as far as setting my BIOS to: (forgive me if the following isnt exact terms as in the bios)
ATA = PATA Channel only
keep SATA = YES
(and some settings i can't remember)
I was able to boot my computer up with the SATA HD partitions set at the next available drive letters.
Now here's the problem.. I currently have an Image of my C: (system) created with Acronis TrueImage 8, and i restored that to my SATA drive's FIRST partition...
The first partition is also formatted with the same file system NTFS and is set to primary..
From here, i honestly dont know what to do..
ofcourse I will have to set bios to boot the SATA drive first...
Also, since the System image (windows XP) is that of DRIVE C: I have to somehow set the SATA drive to be HD0 (first channel)... playing around in my bios I have accomplised to have set my SATA drive as IDE channel 1 = Primary.. funny thing is the rest of the drives moved down starting at IDE Channel 3 and 4..
Still i went on to boot up.. but i was unsuccessfull. I get a very quick blue screen (about 50 miliseconds) and then my computer shuts off and reboots..
I played around witht he settings and tried many things.. still get the quick BSOD and then reboot problem
GUys? What am i missing here?
I didnt know this SATA drive was gona get complicated.. i thought i'd be up and running by now.. :( ..
Please lend me some of your knowledge peoplez.. :D
tea

Hi Danny,
Thanks for your reply.
I have followed your instructions to the dot.. now im getting as far as the WindowsXP Boot Screen... after an unusually long loading time, i get that BSOD flash which i really cant make out since the darn thing reboots right away.. :(
I also tried
Native Mode
ATA Configuration - SATA only
(changing this to SATA, thinking you were mistaken since am booting sata up.. but what do i know ei?)
SATA Keep enabled - yes
PATA Keep enabled - yes
PATA channel selection - both
same results... a long boot screen loading time.. then a quick BSOD..
I alsto tried booting up in safemode.. the loading stops at agp440.sys and reboots after a long pause at that part.
So now I switched back to your recommended settings, but this time setting my old hard drive to boot (PATA).
To my surprise im back to where i started (despite maintaining your suggested settings) thus i am replying to this post again..
also, i noticed that with your suggested settings, my SATA drive is on IDE channel 1.. and the rest on IDE channel 3 and 4.. but here in windows my old hard drive is still drive C:.. I was expecting my SATA drive to be Drive C this time.. could this be the problem here?
I mean the windows Image I restored is setup to work on drive C (first drive), although I removed all the drive, could it be that my SATA drive is still not on drive C?
Please help. My brain's bleeding
Tea

Will the MSI K8T Neo2 FIR support what I have?

Well, I bought an abit av8 mobo, hoping to make my new happy computer system.. Turns out, after I built the thing, my happiness ended... I tried basic setup-1 dimm on each bank, nothing, same POST code. So, I RMA'ing the mobo and getting a MSI K8T Neo2 FIR mobo, hoping that it WILL work (a bit more, but worth it). Will it support what I have right now?
1 gig Crucial PC3200 Ballistix
1 WD 74 GB Raptor HDD
1 Maxtor 80 IDE HDD
1 XFX GeForce 6800 (it says minimum is a 300w PSU)
1 Thermaltake 480w Silent Purepower (+12 rail is 18a... mm... ouch...)
1 Thermaltake Venus 12 HSF
1 AMD 3500 Skt 939
1 Nec DVD+RW/-RW DVD burner
1 Mitsumi Floppy Drive
4 CoolerMaster Green LED fans
4 temperature controlled crystal fans
1 Blue LED fan
I think I might have to upgrade the PSU...

Nobody can garantee you that it works you have to pay s.o. to take risk or risk it yourself.
Well I'd just try it, you'll always find a friend that can lend you a stick of ram for a day or two.
I was working in a computer store when I got my rig and I tried 4 different kinds of memory till everything worked perfectly.
I just wanted to warn you, not to frighten you.
Moreover you could check MSIs memory compatibility list....
DO IT :hypecrite:

K8t neo2-FIR lock ups

hey i'm posting for my friend who recently got a new setup for his computer
antec 400W power supply
3200+
k8t neo2-FIR
sapphire radeon 9600XT
512 meg major brand ram
2 80 gig harddrives
onboard sound/lan
i'm not too sure of the psu specs
the computer (with latest driver updates) has a tendency of locking up where the screen will just go black at random periods
no matter the situation and we will have to restart it (we tried in optimizeed bios settings and default)
the computer when i was there ran fine in video games except for the locking up part
i'm not sure what the problem is nor does my friend any help is appreciated

Run Memtest86 and find out which RAM models he uses. Likely as not it is going to be part of the issue. See if you can read the lable on that PSU as well and find out how many amps are on the 12v rail.

K8T Neo2 V2.0 SATA-Problem

Hi Folks,
I got a "problem" with my K8T Neo2 V2.0. At first I had 3 IDE-drives, but I needed a new DVD-burner to read double-layer discs. So I bought a SATA-Drive, plugged it in and it worked good. (VIA 5.13A hyperions). After that I decided to go for a new, bigger, faster harddisk .. also SATA. I wanted to profit from the speed so I made a clean install of Windows XP on that new SATA-drive. BIOS was set to IDE and the Windows-setup recognized the drive correctly without an driver from floppy. Then I used the newly released 5.14A Hyperions and the strangeness began. Suddenly the safe-removal-icon for the SATA drives in the taskbar was gone, no more hot-plug capabillity I thout. I wanted to install a game from DVD and I realized darn slow read-speed from the new DVD-drive. I read only with 3x-speed and double-layer DVDs with 2x. I made a repair-install of Windows XP an rolled back to the 5.13A Hyperions and now my safe-removal-icon and the normal read-speed is back - but now sometimes I get an "program-lag". When I close a programm and want to open an other, or just a menu or something, sometimes the PC don't react for 1-2 seconds.
Any suggestions? Any knowledge about SATA-behavior on the K8T Neo2 V2.0? (or the VIA Hyperions?)

Well here are some specs:
Athlon 64 X2 4200+
2x 512 MB DDR400 RAM, Infineon
1x IDE HDD, Maxtor 6Y120P0
1x SATA HDD, Seagate ST3250410AS16
1x IDE DVD-Drive Pioneer A06S
1x SATA DVD-Recorder Plextor PX-810SA
Creatice SB Live! 5.1
PSU Enermax 350 Watt (EG365AX-VE / 3,3V=32A; 5V=32A, 12V=26A)
Windows XP Pro with SP2 installed on SATA-HDD
The Hyperions from the MSI-Driver CD also don't work (same no-hot-plug-problem).
In the BIOS the SATA-channels are configured as IDE, I never needed a driver floppy for XP-install.
The system event-log only shows one failure "loading of boot- or systemdriver viamraid failed". When I had my old XP install on the IDE drive (with installed 5.14A hyperions) the VIA V-Raid utility was installed and could be started, the hot-plug-ability was working as I plugged in the DVD-Recorder. Then I installed XP on the new SATA-HDD (with plugged in dvd-recorder) and the problems came up. Also now no via vraid-utility is installed.

Help installing XP Pro on K8T Neo2-F!!!

I'm trying to help my cousin install XP Pro on their new pc. It's got an Athlon 64 3000+, K8T Neo2-F, 512mb Samsung ram, and an 80gb ata drive. before i started to fix it, my cousin said that he stopped the xp install midway thru because he forgot to install the RAID drivers. when i try to reinstall xp, it just freezes on DOS when it says "setup is checking hardware configuration" or sumthin like that. i also noticed that their dvdrw drive stops spinning and has a clicking noise at that point. i tried installing win 98 on it and it worked, then tried to upgrade to xp, which froze when the pc rebooted. anyone have any idea what's going on???

Hi. My setup is very similar, and I had a similar problem installing XP as well. Do as simon suggested to make sure your harddrive is clean for a fresh install. Make sure the promise 579 SATA controller and the VIA SATA RAID controller are both disabled in BIOS. Especially if your not using a RAID setup or any SATA drives you wont need them anyway.
Install XP as normal. Do not install the RAID drivers from the floppies by hitting F6. Now the XP installation should be able to complete itself. If you want to use the controllers later, enable the one (or both) you want in BIOS, Then install the drivers from the CD under Device manager update driver option.

Just got my RMAed MB(K8T NEO2-F) back GOING GOOD@264FSB

Similar Messages

Maybe you are looking for