Just setup new Draytek vigor 2750N...... + resetti...

HI all
i mentioned on another thread http://community.bt.com/t5/BT-Infinity/New-draytek-sync/td-p/517941/page/2
that i was getting a  Draytek vigor 2750N. I got it from ebay for about £100.
As it was used off ebay i took some advise and factory reset it 1st.  was quite easy to setup. and is now up and running.  just a couple of Qs
username/password  should this be my @btinternet.com email address /password   or home@bthomehub thiny (cant remember it exactly) and leave p/w blank? 
also on the stats page is there somewhere that tell me what each is   e.g 1Day CV, Total FEC etc.?
next question is simple but bit lengthy..
As as previously mentioned in another thread.  after having a few engineer visits and disconnections on my line, my profile dropped from btspeedchecker ( was about 32mb)  dropped down to a low of about 27ish.  
Now i have read mixed advise about if people should actually disconnect (reboot) the modem(and ot routers) to give the line profile a kick/push  or just to leave it to naturally increase (with DLM).. as some warn that it may reduce it even more so with the disconnections. (as DLM thinking line is unstable and lowers speed accordingly)
From my finding i found that...   if i did keep disconnecting the BT OR modem that it would keep dropping the line profile by a meg or so each time..  however what i did was after a reset and seeing it drop i  kept downloading large files (50gb - 100gb) at a time at full speed  to show the line was capable to handing downloads at the max speed) i did this for a day or two   however the profile wouldnt "naturally increase" after doing another btspeedcheck.   so after a day or so of heavy downloading  i would then give the modem a quick blip (usually at off peak times like  late night or v eary morning   this did actually raise the profile.. 
and kept following the same process.upto  2 nights ago i was working late till about 2am  profile was at 31.51mb so rebooted modem (had to wait an hour for another test) and it increased to  33.62mb (highest i seen since 1st of may from when i had work done)  which its been at since now  (installing draytek)
now i installed the draytek 2pm today.  line profile decreased to 32.77  was disconnected for about 5 mins as had to input settings etc.  so im hoping after a day or 2 of downloading again this will raise up..  
However with the draytek router/modem  will i need to give the unit a reboot to see the profile increase(or decrease)   like the BT OR modem or will this naturally increase(or decrease) itself??
if someone can tell me how i will paste a image of my stats from the draytek so you can take a look and see what you think??
thanks
Grant 

If you use the power on/of switch you will lose your settings.
The best way is in the admin section,as that has a choice of a factory reset or a warm reset.
If you do any resets though it is a good idea to save your settings first from the admin section.
Another good move if you have not done it is to change the PW [system PW] in the admin section as all drayteks use admin/admin,you need to use admin/xxxxxx,but don`t forget the new PW or you will not get in.
But personally I think that a reboot will only make your profile worse as with the draytek you are rebooting the modem and the router sections.If you leave it on it should get stable again,but the choice is yours.

Similar Messages

  • Draytek Vigor 2750n Connection Issues

    Guys,
    After searching the forums I chose to purchase a Draytek 2750n from BB for a replacement for my BT Infinity kit, however for the life of me I cant get the Draytek to connect to Infinity; I've followed the below guide and have had no luck;
    http://www.draytek.co.uk/support/kb/kb_vigor_v2750_setup.html
    I've tried all username conventions, my BT Yahoo email and password, [email protected], with a "space" as a password, [email protected] with a "space" as a password with no luck.  I can see the initial VDSL2 sync and with a profile of 17a however the Draytek constantly shows Idle > Handshake > Training.
    I did notice that the Draytek time was set to 1970!! could this be the issue?
    Infinity was recently placed live in my area with one of the smaller slimline cabs, is there anyway that the cab can only be accepting connections from the Openreach Modem? Can any BT forum guys advise?
    Can anyone share any experiences they've had, I'm at a loss and dont want to return the modem
    Cheers,

    Cleric wrote:
    toekneem wrote:
    Mine is set up with [email protected]  Space for a password details are all you need, and it definitely works with the 1.5.1 firmware
    The details are the same as page 19 of the BT Infinity user guide and troubleshooting booklet.
    One always gives way to one's elders and betters! :
    Belt and braces you have two options here both of which are known to work so if at first you don't succeed - try the other one!
    err!!! 3 options......go back to the OR Modem and HH
    [edit] It must show that you may be able to put what you want in, as long as the telephone number authenticates
    toekneem
    http://www.no2nuisancecalls.net
    (EASBF)

  • BT Infinity - DrayTek Vigor 2820 - Connection Drop...

    Hi everyone,
    We're having a few issues with BT Infinity when using a DrayTek Vigor 2820.
    We stopped using the official BT Fibre modem when we started having endless port forwarding issues (which I don't really want to go in to here.. it's a a long story!)
    We did some reviews, and ended up purchasing a new DrayTek Vigor 2820 Fibre modem router. It's connected to the BT fibre modem, and then into WAN2 of our DrayTek router. 
    We seem to be getting random drops in connection, sometimes the cable modem drops which results in a log at BT's end showing the connection disconnect. Usually, the connection doesn't drop, it just appears to time out for around 2-5 seconds. If you're downloading, it cuts the download - so is quite annoying!
    I've looked into the logs on the DrayTek which don't tell show that much - lines of interest are below.
    Any ideas anyone could suggest would be most appreciated!
    Andy
    PPP Connection Log:
    0:00:57.920 PPP Start (WAN-2, [email protected])
    0:00:58.210 CHAP Login OK (WAN-2, [email protected])
    0:00:58.230 IPCP Opening (WAN-2, [email protected])
                 Own IP Address : 81.xxx.xx.xxx  Peer IP Address : 81.xxx.xx.x
                 Primary DNS : 194.72.0.114  Secondary DNS : 62.6.40.178
    15:25:28.440 PPP Closed : No Echo Response (WAN-2, [email protected])
    15:25:37.450 PPP Closed : LCP Time-out (WAN-2)
    15:25:40.110 >>> Dial-up triggered by user : 10.250.251.23
                 proto=UDP, to 192.55.83.30 port=domain
    15:29:11.290 PPP Start (WAN-2, [email protected])
    15:29:11.570 CHAP Login OK (WAN-2, [email protected])
    15:29:11.580 IPCP Opening (WAN-2, [email protected])
                 Own IP Address : 81.xxx.xx.xxx  Peer IP Address : 81.xxx.xx.x
                 Primary DNS : 62.6.40.162  Secondary DNS : 194.74.65.69
    Log continues like this
    Solved!
    Go to Solution.

    Hi ninjaandy, I don't understand this,
    "We stopped using the official BT Fibre modem when we started having endless port forwarding issues (which I don't really want to go in to here.. it's a a long story!)
    We did some reviews, and ended up purchasing a new DrayTek Vigor 2820 Fibre modem router. It's connected to the BT fibre modem, and then into WAN2 of our DrayTek router."
    You say you stopped using the BT fibre modem in para 1 and then you say you connected the new 2820 to the BT fibre modem?? Why not just connect your line that went to the BT modem directly to your 2820?
    I also have a Draytek 2820n (not the fibre version) and I connect the ethernet cable from the BT modem to the lan2 port on the Draytek and have had no problems. Hope this helps.
    wedding
    Mistakes and embarrasing goofs in e-mails are only discovered when you've sent them!

  • I've just setup my new iPad Air. With new Apple ID ect everything working fine, but I can't redeem my iTunes voucher it says wrong password/ user name but they are not wrong. I've reset password same problem anyone help?

    II've just setup a new iPad Air for my daughter with a new apple ect, everything is working fine, but I can't get it to redeem the I tunes voucher. It asks for I'd and password, put them in and comes up with wrong Id/password. They are not incorrect answers, but reset password just incase. Same problem. Also tried making another apple account. Same problem again can anyone help?? Please  

    Your iTunes Voucher is link to the old Apple ID.

  • I just got a new iPhone and have reset my iCloud password 3 times on my computer but each time i try to enter on my new phone it does not recognize.

    Any thoughts on how to fix this?

    To be clearer, i just got a new phone and have reset my iCloud password three times on my PC but it is not taking on my phone.

  • HT1349 Hi all,I have just purchased new iphone but have difficulty in completing the itunes download with message : problem with Windows installer package. A program run as part of the setup did not finish as expected.

    Hi all,I have just purchased new iphone but have difficulty in completing the itunes download with message : problem with Windows installer package. A program run as part of the setup did not finish as expected.
    Would appreciate help...its driving me up the wall!!

    Perhaps let's first try updating your Apple Software Update.
    Launch Apple Software Update ("Start > All Programs > Apple Software Update"). Does it launch and offer you a newer version of Apple Software Update? If so, choose to install just that update to Apple Software Update. (Deselect any other software offered at the same time.)
    If the ASU update goes through okay, try another iTunes install. Does it go through without the errors this time?

  • I've just setup icloud on our new ipad but can't get any music to play on the ipad.  It shows everything that is in our itunes but they won't play.

    I've just setup icloud on our new ipad but can't get any music to play on the ipad.  It shows everything that is in our itunes but they won't play

    Keep the Powerbutton and the Homebutton pressed at the same time until you see the Apple logo on your iPad screen.

  • I have just setup a new ipad and the first app I downloaded was ibook.  I pad says its installed but I can't find it.  any suggestions please?

    I have just setup a new ipad and first app I downloaded was ibook.  my ipad says its installed but I can't find it.  any suggestions please?

    For some reason this happens to some people.  The one thing that works is to reboot your iPad.  To reboot:  Press and hold BOTH the power and home buttons at the SAME time for at least 10 seconds (ignore the red slider) until the Apple Logo appears, then let go of both buttons and your iPad wil restart.  Once it's back up, I'm betting you'll see iBooks.

  • Just got NEW Apple TV, The status light went out during final part of setup and it no longer works

    Just got NEW Apple TV, The status light went out during final part of setup and it no longer works.  Any ideas?

    If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
    Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
    Connect the micro USB cable to the Apple TV and to your computer.
    Reconnect the power cable (only for Apple TV 3)
    Open iTunes.
    Select your Apple TV in the Devices list, and then click Restore.

  • I have smurf village on my ipod and just downloaded new smurf village to my ipad, but it has reset my game on the ipod.  how to l fix this and can l get my original game position back.

    i have smurf village on my ipod and just downloaded new smurf village to my ipad, but it has reset my game on the ipod.  how to l fix this and can l get my original game position back.

    If it is the same app for the iPod and the iPad (universal or iPod/iPhone app) and not a iPad only app, the only way is to restore the iPad from the backup of the iPod.  That will wipe out all the app data currently on the iPad though.
    If the iPad is an iPad only app, then there is no way.

  • Just got new iPad 3.  Not able to setup my Ohio.edu email account

    Just got new ipad3.   Not able to setup my Ohio.edu mailbox

    I'd talk to your school tech support and see what settings they have in place. For example, I can't access my work's e-mail via the exchange app but I can via the web access...largely because it's not a work iPad and they won't allow that kind of access on a device that's not 'their own'

  • Just setup a new i phone 6  if I restore from Itunes will I loose what I have already setup

    Just setup a new ipone 6  if I restore from Itunes will I loose what I have already setup

    Hello maspeds45
    When you remove iTunes, you are just removing the software; the media files still remain in place. Just follow the steps in the article below to remove iTunes from your computer if you are on Windows. If you are a Mac, just download the install file and it will reinstall the software for you. 
    Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
    http://support.apple.com/kb/ht1923
    iTunes 11.1.3
    http://support.apple.com/kb/dl1614
    Regards,
    -Norm G.

  • HT4623 I just updated my IPAD and it reset everything to a new IPad.  I lost everything that was on it.  Is there anyway of retrieving my pictures??

    I just updated my Ipad and it reset everything to factory settings.  I lost everything on the IPad.  Is there any way of retrieving my pictures??

    Yes, as Diavonex said to restore your iTunes or iCloud backup.
    Please following this.
    http://support.apple.com/kb/HT1766
    If it does not work, you may try a 3rd easy iPhone recovery tool to get your pictures back.
    You may refer to this to have a try.
    http://easy-iphone-recovery.blogspot.com/2013/09/iphone-recovery-resource.html
    I think this is helpful.

  • DrayTek Vigor 120 + Airport Extreme Base Station?  I have queries.

    Ok, so my 3 or 4 year old USR 9108 router went down today-- again. I'm fed up and want a new one. It dies on me once or twice a month. It has decided it doesn't like my powerline adapters lately. and I'm fed right up. I run an internet radio station and what I need is stability.
    At the moment, I'm thinking of setting up a DrayTek Vigor 120 ADSL modem (modem-only) with the Airport Extreme Base Station for my router. (I already have an Express on my network.)
    First of all, can anyone please comment on whether they have this set-up and whether it's solid? I've heard good things about both of these devices, and I need something that's not going to flake out as regularly as my USR has been doing of late. Rock solid is a good thing for a 24/7 stream.
    Second, can I just confirm a few questions that I think I know the answer to, but want to be sure before shelling out?
    I am in the UK using an ISP that uses PPPoA; so I need to be sure the modem has a PPPoA to PPPoE bridge in order for the Airport to talk to the outside world. (Right?). I gather the DrayTek will do this. Will it therefore be just a question of setting the Airport to connect via PPPoE and then entering my ISP login settings in Airport Utility?
    I need a setup ideally that, like the USR, will allow me to assign IP addresses manually to some machines or devices on my network but allow DHCP on other things (like my iPhone). It's particularly important that the radio stream should have a static IP. I gather, from having a play with my Express's settings, that I'll be able to accomplish this either directly or by DHCP IP-reservation. Directly would be preferable. Therefore, if I, e.g., assign my computers an IP address on their local network settings and then just shift the Airport's DHCP range so that it starts with (say) 192.168.1.10, rather than, 192.168.1.2, will the Airport be happy with that?
    I also need port forwarding / port mapping. This should be o.k., right?
    Thanks for help, people.

    I'm running a very similar setup here in the UK. I use a Netgear DG834 rather than the Draytek 120 which I was looking at. I use a Time Capsule connected to the router which is in half-bridge mode and this allows me to connect using PPPoE, which is possible on the BT ADSL network, which I didn't know before! - there's no need to get an expensive PPPoA-PPPoE bridge. I guess the Draytek would do an even better job than the Netgear, but mine was the free solution
    I use the TC to give out addresses to a network of various kit, with one fixed IP for a specific device. I find the TC and my airport express very easy to set up and run, if slightly light on the details of what's actually going on. That said, if it doesn't work, then they're probably broken!
    Nothing you've asked for is out of the ordinary / impossible on the apple kit.
    Hope that helps!

  • Question about Draytek Vigor 2850vn max sync

    Hi all, Accidentally lost the first message I had finished typing, didn't post successfully. Anyway, Infinity is near (one of those new green fibre cab's just appeared next to the PCP I should be connected to) and I wanted to ask if anyone knew whether the Draytek Vigor 2850vn is limited to 50mbit sync on VDSL/Infinity? Some places I found on Google mentioned that but I am uncertain if it's true. If it's not true then I'll be ordering it on dabs hopefully before the cut-off time, as I can use it to temporarily replace my Draytek Vigor 2820 router and use it on ADSL until Infinity is ready for my postcode. Many thanks.
    Solved!
    Go to Solution.

    Not sure if this helps but I emailed Draytek a while back about this - they replied Jan 19th so things may have changed:
    "I am thinking of replacing the modem supplied with my BT Infinity connection and was wondering whether the 2850n/vn would be suitable.
    In the description you state that "The Vigor 2850 is a variant of our Vigor 2830 series with the addition of a built-in interface which supports both ADSL/ADSL2+ and also VDSL lines (such as the BT Infinity™ service) for connectivity up to 50Mb/s"
    My question is about the "connectivity up to 50Mb/s" part. Currently BT infinity is an "up to 40Mb/s" connection but there will soon be an upgrade to "up to 80Mb/s".
    Would the 2850n be able to support this speed or is 50Mb/s the maximum it will support? In fact what is the maximum VDSL speed that the 2850n and 2750n support?"
    The reply was:
    "Both the 2750 and 2850 support these VDSL profiles: 8a, 8b, 8c, 8d, 12a, 12b, 17a, 30a 
    The units can connect at high speed profiles however it just hasn't been tested
    on those. The actual internal maximum possible rating does exceed 50Mb/s
    but right now we're using a conservative official maximum speed."
    I didn't buy one in the end!

Maybe you are looking for

  • How to use (Verify database) in DB13.

    Dear all, I tried to use (Verify database) in DB13 but it doesnt works. It says that the instance is up. HOw do I use this option in DB13. Thanx in advance. Lalit Rana

  • Evaluation of html stored in the database

    Hello everyone, here is my story. I have html stored in the database that I am using in regions. The region is a pl/sql anonymous block with code similar to this. DECLARE testt varchar(30000); BEGIN SELECT Main_Page_Image_Zone INTO testt FROM htmltab

  • Multiple photo develop settings paste not working

    Hi all keen photographers out there. Using Lightroom V5.7. I adjust one photo aka highlights, shadows etc..then copy and paste to many many photos.sometimes over 1000 shots. Only some of the photos will have the develop setting pasted. Any ideas why

  • Installing Oracle 8i Enterprise Edition on Novell Netware Platform

    Where can I get documentation and a copy of the Oracle 8i CD packs for installing on a Novell Netware platform? Thanks

  • What is "Firmware Could Not Be Found" message?

    I got a new iPod Nano (8GB) so I used the same iTune software installed in my laptop. I registered the new Nano on-line and then copied all the songs to the new iPod. The iPod is working fine (transferred music from the laptop and at I can listen to