Just turned on new ipad touch 4 screen just has a itunes logo and pic of usb cord cant clear it
just turned on brand new IPOC touch 4, screen only has a pic of Itunes logo and dsl cord going to it. cant clear it.
What happens when you connect to your computer that is running the most recent version of iTunes?
Stedman
Similar Messages
-
My Ipad mini had frozen with an Itunes logo and image of USB lead.
If I turn it off it goes back to that screen
You probably have to restore the device with iTunes so connect the iPad to your computer and launch iTunes.
You want to use the same computer that you always sync with so that you can restore your app data and settings. You can restore with any other computer, but you will lose everything on the iPad.
Instructions can be found here.
http://support.apple.com/kb/ht1212
You will probably need to restore using Recovery Mode. You can read about it here.
http://support.apple.com/kb/ht4097
Recovery Mode Instructions
Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
Use iTunes to restore iPad. -
How do I fix my phone? I went to dowload ios 7.0.4 and it went to this blank screen wih a charger pointing up to the iTunes logo.
http://support.apple.com/kb/HT1808
you may have to do those steps a few times. -
I just did the update for my apple TV and it got halfway through the update the TV screen showed a itunes logo and a plug in cord and wouldnt respond. I unplugged it and plugged it into my computer to try and restore it and now I can get audio but no vide
DFU mode? How do I do that? So far the only thing I can do is hold down both buttons to power it on and nothing is on the screen and it wont reconize on my computer....
-
I clicked the button in my setting thatz is saying "software update iOS 6.1.2. It turned off and now My iPad 2 is stuck on a black screen that has the iTunes symbol and a charger that I'm guessing means "plug into iTunes". I did so and then waited four hours to download something. And now it is saying that its going to update my iPad but it isn't working. I tried to "update" twice. I am VERY ANNOYED beczuse the last time i updated it, it just turned off and i didnt have ot plug it in or anything. WHY IS IT DOING THIS.....?????? My ipad will not turn on or anything. Help me FIX THIS!!!
hi Kinney. last hour, i update my ipad 2, then im having the same problems as u. im also hoping people can solve this issue.
-
My iPod touch is off and wont turn on because it has the itunes logo and a usb pointing to it, so when i looked it up online, it says i have to restore it but i don't want to because i don't want to lose all my pictures. What can I do?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
I thought I was updating my IPad, i selected update and came back home to the screen frozen with the Itunes symbol and a plug in cord displayed. I can not get it to do anything. Any suggestions?
Your iPad has gone into recovery mode and it needs to be restored now. The instructions are in this kb article.
If you can't update or restore your iOS device - Support - Apple -
HT201412 my Ipad screen is stuck with Itunes logo and wont repsond
my Ipad screen is stuck with Itunes logo and wont repsond
Connect to iTunes on the computer you usually Sync with and “ Restore “...
http://support.apple.com/kb/HT1414
If necessary Place the Device into Recovery mode...
http://support.apple.com/kb/ht4097
Note on Recovery Mode.
You may need to try this More than Once...
Be sure to Follow ALL the Steps... -
My iPad has the Itunes logo and USB cable on screen. Can I still back up my files?
If you haven't already done so, its unlikely.
You can try holding both the home and power buttons at the same time until the apple logo appears on the screen, then let go. -
My ipod was updating overnight. I woke up to find the screen frozen with the itunes logo and the usb charger. I've tried hooking it up to itunes but it says I need to restore and update but I've tried to do that and it won't. What should I do?
- Try placing the iPod in Recovery Mode and restoring via iTunes
- Next try DFU mode and restore.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings -
my iphone has a itunes logo and usb cable picture on the screen....what can I do to get it to work
What happens when you plug your phone into itunes
-
My Iphone 4 will not turn on all it will do is show the iTunes logo and and arrow point to it with an image of the connector to power cord. Ive tried to turn it off, taken out sim but nothing
Hello there, FrancesCech.
The following iPhone Troubleshooting Assistant should help with what to do with your situation:
Apple - Support - iPhone - Restore Troubleshooting Assistant
http://www.apple.com/support/iphone/assistant/restore/
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro D. -
I was updating my iPhone 4 to 6.1 and it froze. It has an iTunes logo and picture of a usb port on the screen. It gave me the option to restore settings, which I don't want to do. Now the phone is frozen. Any ideas how to get the phone back?
Im sorry to hear that. You need to restore like brad said.
But you can restore from a latest backup from itunes after restore. I hope you had a recent backup made.
Here is a link to help
http://support.apple.com/kb/HT1808 -
Iphone 5 screen is stuck on itunes logo and USB cable?
iPhone 5 screen is stuck on iTunes logo and USB cable. Reset does not work.
Place your device in recovery mode as explained here:
iOS: Unable to update or restore -
MY IPAD IS STUCK FOR ALMOST ONE DAY.. LAST NIGHT I TRIED TO INSTALL THE LATEST IS UPDATE WHICH IS IOS 6.1 BUT THEN MY IPAD2 TURNED OFF AND THE ITUNES LOGO AND USB CABLE CAME OUT ON THE SCREEN SO I TRIED TO CONNECT IT TO MY ITUNES ON MY COMPUTER AND IT SAYS RECOVERY MODE SO I CLICKED OK BUT THEN IT ALWAYS END UP CORRUPTED... AND IM CONNECTED TO MY INTERNET 24/7...I JUST DONT KNOW WHAT TO DO...I HOPE APPLEWILL FIX THIS AS OSOON AS POSSIBLE...SO DISAPPOINTED!! PLEASE HELP ANYONE... BEEN TRYING TO RECOVERY MODE OVER 150 TIMES...
Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times.
Maybe you are looking for
-
Printing Problem with layered photos
I have sent my InDesign document to the printer for reproduction. There seems to be a problem with the output. A couple of the photos (layered) did not print. On my personal printer they print fine both directly from InDesign and the PDF I created
-
Defaulting Valuation type of header material in production order
Hi PP users, I have a scenario where a Semi-finished material SF is subject to split valuation as per valuation type = In-House & Export. However, the production of SF is always done in MTS environment and client wants that each production order for
-
Hi, I am using the BOX control command in SapScript. Is it possible to assign the values of Xpos and Ypos dynamicalliy. In BOX XPOS 16 CH WIDTH 0 MM HEIGHT 18 MM FRAME 10 TW, i want to assign the values at runtime, instead of xpos 16 , something like
-
NDR: recipient not found
So I've seen a like a million different questions on this, and a few resolutions, and even fewer similar resolutions. I'm probably missing something really simple, but I haven't had any extra eyes on it, so here it is: Generating server: BN1PR0301MB0
-
HI THERE i have startup oralce streaming on database(object) level, capture and propogation on source database is OK, But the apply process on destination database give error, and the error is following. ORA-26687 no instantiation SCN provided for "S