Just upgraded to snow leopard, downloader apple support drivers for canon mp620. Why won't a printer list display in add printer window?
Just upgraded to snow leopard, downloader apple support drivers for canon mp620. Why won't a printer list display in add printer window?
Assuming the MP620 is connected to your wireless network, then there are two components to this device - the printer and the scanner. The printer uses Canon proprietary software while the scanner is supported by Apple's Bonjour service. So in many cases, you will at least see the scanner, shown as Bonjour Scanner in the Kind column, while the printer can take longer to appear and is shown as canonijnetwork in the Kind column. If you cannot see either then you have a network issue. Try turning off the MP620 for a minute and then turning back on. Then see if the scanner / printer component appears in the Add Printer window. If you still don't see either, then confirm the MP and the Mac are using the same network. If you know the MP's IP address you can use Network Utility to Ping the address. You can also enable Bonjour Bookmarks in Safari preferences and when selected, the MP620 should appear.
Similar Messages
-
I have just upgraded to snow leopard and lost my epson printer software. I have checked Epson Aus web site for printer software but they haven't upgraded it for snow leopard. Am i able to download software for a lesser operating system then snow leopard or do i have to purchase a new printer? The model is stylus photo R310.
Have you tried the R300 or R320 software? Typically the software covers a broad spectrum of printers, often providinbg overlap to cover "relatives" of a series.
http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?BV_UseBVCookie=yes&oid= 47541&prodoid=47915738&infoType=Downloads&platform=Macintosh -
I just upgraded to Snow Leopard then Lion and the computer shut down after installation.
Now when it starts up it gets as far as the apple icon and then shuts down again
whenever I turn it on it loads that far and then closes.
HELP!Restore your bootable backup/clone or Time Machine backup of Snow Leopard, launch Disk Utility from the install disc, repair the boot volume, and reinstall Lion.
-
I just upgraded to snow leopard and some of my printers disappeared and I am unable to get them back any ideas
Hello DaveDue
Start your troubleshooting with the article below, you may need to download the printer drivers directly from the manufactures website.
Troubleshooting printer issues in OS X
http://support.apple.com/kb/ts3147
Regards,
-Norm G. -
HELP!! i have a ton of videos of my boys stored in iPhoto..They played fine on my old OSX system (leopard). However, I just upgraded to snow leopard and then to mountain lion and now i can't open my videos at all anymore. HELP!!
Can you tell us about one or more of the video files - what are they? QuickTime? MP4? Something else? How did you create the video files in the first place?
I do a lot of video and when I upgraded to Snow Leopard I discovered that many of the QT videos that I had created previously (via iMovie & Final Cut) would not play correctly in QuickTime X - the bizarre behavior was that QT X acted as if my video files were only audio files! I reported this to Apple at the time but never heard anything back, and there hasn't been any change in later updates to QT X.
The solution was to (re)install QuickTime 7. But first look in your Applications > Utilities folder. When you upgrade from Leopard to Snow Leopard, the installer normally moves the old QT 7 program to your Utilities folder. If it's there, try using QT 7 to play one of your video files. If QT 7 is not there, you can download and install it from here Make sure you are running at least OS X 10.6.3 before you install QT 7. It's even better if you make sure you are running 10.6.8 which was the last release of Snow Leopard. -
I just upgraded to snow leopard and now my intellipoint mouse doesn't work, I tried downloading a new driver and it installs successfully except an extension but it still doesn't work, is this typical of the OS higher than 10.4? Is there any way I can get around this problem?
You need to check with the mouse's developer and see if it's supported or not. That information wouldn't be known by users on this forum.
-
Just upgraded to Snow Leopard but my Logic Studio software quit functioning, anyone else ever have a something like this happen?
Hi
This may be relevant:
http://support.apple.com/kb/TS3968
CCT -
After a long time, I have just upgraded to Snow Leopard. My computer is seemingly running so much faster, could this be because of the upgrade? The reason it took me so long in the first place is I could not find the location to delete all the used memory. I happened to luck upon a place just the other day that said "all media". From there I was able to go through and get rid of approximately 15GB worth of memory. My computer has been saving multiple copies of all my images. I do not know how to make this stop happening. Has anyone had this experience?
10.6 is faster than 10.5 because of updated video drivers, however the machine will slow down if you upgrade OS X past 10.6.8 as 10.7 and 10.8 are more hardware demanding operating system verisons.
Also 10.7 and 10.8 will not run your PPC based software or older Intel software, requiring all new purchases.
From there I was able to go through and get rid of approximately 15GB worth of memory
What you did was free up 15GB of storage space on your boot drive which if a boot hard drive is getting near full will slow down the comptuers performance. Ideally it's best to stay under 50% filled, but never more than about 80%.
Your "memory" actually refers to the RAM which the processor uses as temporary storage space while it works on things.
Why is my computer slow?
My computer has been saving multiple copies of all my images. I do not know how to make this stop happening. Has anyone had this experience?
Sometimes the duplicates are actually thumbnails, or tiny versions for rapid display in programs like iPhoto with the smaller images to preview before you click the larger version, so they will always be recreated.
Hopefully you didn't delete the original larger files by accident.
The "All Images" is particularly dangerous if not used wisely.
Also it might have been you forget and duplicated the images at one time or another.
https://discussions.apple.com/community/notebooks/macbook_pro?view=documents -
I have just upgraded to snow leopard and ical now wont open. says it is not compatible and is ical 3.0.2 which seems strange as i have a osx10.6.3 . have looked for update but cant find one, what do i do?
Greetings,
It sounds like you have moved iCal from it's normal location and are opening a second copy which is the older version.
The current version of OS X 10.6 is 10.6.8. As you are running 10.6.3 you need the updates. Go to the Apple Menu > Software update and keep doing this until it says all updates have been installed.
Click anywhere on your desktop (the background).
Go to the top of the computer screen and click on "Go" > "Applications"
In this list look for "iCal".
Double-click iCal in this location (which is the proper home for iCal) and see what version it says.
If it reports the correct version you can drag the iCal from the Applications folder to the dock on your screen to add an button for it (if you already have one in the dock, remove it before you drag this one there). Be sure to leave iCal in the Applications folder.
Hope that helps. -
Just upgraded to Snow leopard; can't receive photo attach's in email
We just upgraded to snow leopard and now can't receive photos in email attachments. All that pops up is a bunch of alpha-numeric characters in some emails and the little blue boxes with the inserted question marks in others. Also seem to note that replies are not denoted or marked/flagged as they were in the previous version, though this is not as big a deal as the said replies seem to make it to their intended destination. Mail version is 4.5 (1084). Please advise
Another note, Ernie... I said that I emailed a pic from the imac (which is where I'm having the problems... snow leopard?) to my ipad and no problem, the pic shows up fine; but if I then forward that email BACK to the imac, then no-go... no pic just the following, and I'm shortening it for simplicity's sake:
--Apple-Mail-1--691056766
Content-Transfer-Encoding: 7bit
Content-Type: multipart/related;
type="text/html";
boundary=Apple-Mail-2--691056765
--Apple-Mail-2--691056765
Content-Transfer-Encoding: quoted-printable
Content-Type: text/html;
charset=utf-8
<html><body bgcolor=3D"#FFFFFF">
Sent from my iPad
<br=
Begin forwarded message:
From:=
"s" <=
skoella@EDITOUT>
D=
ate: April 2, 2011 10:53:08 PM EDT
To: jak@
Subject: really a pic this time
<b=
r>
=
hokay
<blockquote type=3D=
"cite">
</di=
v>
Sherry<=
/span>
WARNING: currently under construction by my Lord and Savior J=
esus Christ
<s=
pan>
</body></html>=
--Apple-Mail-2--691056765
Content-Disposition: inline;
filename="19 pr.jpg"
Content-Id: <8E1037EC-DD94-4CEE-9647-611D5098D161/19%20pr.jpg>
Content-Type: image/jpeg;
x-unix-mode=0644;
name="19 pr.jpg"
Content-Transfer-Encoding: base64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 -
I just upgraded to Snow Leopard, and I have Aperture 3.1.3. Now after I import pics from my camera I get a dialogue box so large that I can't see the eject card button. Consequently, I can't get rid of the dialogue box without having to do a force quit on Aperture. How do I fix?
I can drag the dialog box, but I can't move it up far enough to get to the eject card button. The dialogue box contains all the jpeg Numbers I am trying to upload. It has never done that before. It used to be just a smal dialogue box with no jpeg numbers in it.
It is even difficult to get to the Finder with the Dialague box is open. I have to force quit aperture.
Any ideas would be appreciated. -
i just upgraded from snow leopard v10.6.8 to os x mountain lion and my scroll bar has disappeared on all my applications on the internet. does anyone know a patch to get the scroll bar to work.
Open General preferences in System Preferences. You can set the desired scrollbar behavior there.
-
I just upgraded to Snow Leopard and a new Imac. Could someone tell me where the preference is to change file to open in original program instead of preview?
Right-click on one of the files and choose 'get info'. in the info box. Change the 'open with' setting to your correct application. Check the 'always open with' option before OK-ing the change, then click the 'change all' button before closing the info window.
Typos edited by: noondaywitch -
Just upgraded to Snow Leopard, but Palm device 4.0 won't sync with it. Any hope?
Can anybody tell me how to make Palm handheld running system 4.2.2 work on the Mac I just upgraded to Snow Leopard?
It would help if you stated what Palm device you are using. I had a Tungsten T3 and then an E2 running perfectly well on Snow Leopard before I gave Palm up, using Desktop 4.2.1 rev.d, so you could give that a try:
http://kb.hpwebos.com/wps/portal/kb/na/tungsten/e2/unlocked/solutions/article/33 219_en.html
or failing that 4.2.1 rev.a
http://kb.hpwebos.com/wps/portal/kb/na/tungsten/e2/unlocked/solutions/article/34 115_en.html
though I can't remember what the difference was. -
I've just upgraded from Snow Leopard to Lion. The installation seemed to go OK but on rebooting it is asking where the System Events app is. What is it and where is it located?
ThanksIf the dialogue appeared once, and you cancelled once, the dialogue may reappear when you next log in. For more certainty I suggest a restart of the operating system, then a log in.
If you like: immediately after the problem is worked around, open the Console utility to see whether — amongst its view of all messages — there is an obvious sign of what caused the dialogue to appear. (If you see nothing obvious, don't waste too much time looking.)
Maybe you are looking for
-
Default cell values for column not properly saved in uir file in labwindows 2009 (9.1.0 427)?
I've run into a strange problem with the table control. Basically, even though I set default cell values for a particular column as numeric, when I try to add items to the list it tries to add them as strings, and returns an error message that it is
-
Pricing condition is blocked when editing another
Hello experts, I'm experiencing an issue and would like your feedback. I created 2 pricing conditions for the same Condition type (PR00) and same combination key (see below) MANDT KAPPL KSCHL VKORG VTWEG KUNNR MATNR KFRST DATBI
-
After creating and signing in under a different user on imac, how can i use iphoto pictures?
-
Java plugin won't work in Chrome
Java won't work in Chrome. I have OSX 10.7 on my Macbook Pro, and when I try to update Java, a popup alert is served that the update is only going to work for OSX 10.6. It would be really, really helpful to be able to use Java in my browsers. Any ins
-
Implementing Basecommand interface
hi all, i have created a GUI using swing which i want to evoke as a button in ARC map ,but for that i have to implement basecommand interface and use my code there , but iam not getting it how to do that so can any one give me a code snippet or a des