JVC KD-R200 Radio works but no sound?

Help! Just installed this receiver from BestBuy.com JVC KD-R200. Install went well deck worked great for a day. Took faceplate off and next day put it back on. All the lights and visible power indicators came on but no sound. There is a slight audible pop when the face plate is put on but nothing else. Any ideas?

Jamesr –
Thanks for posting on our forum. Unfortunately, I would not know how to address your concerns. I do not know much about the technical end of decks. I would recommend you contact JVC if we did not install this for you.
JVC
800-252-5722
You can contact your local store as well and speak to a Geek Squad Auto-Tech and see if this is a common issue with your model vehicle or deck.
Thanks,
Jesus|Senior Social Media Specialist | Best Buy® Corporate
Private Message

Similar Messages

I have windows 7 and my speakers worked then after update my speakers do not work and everything checked out and says they are working and that soundcard is working but no sound now.

I have windows 7 and my speakers worked then after update my speakers do not work and everything checked out and says they are working and that soundcard is working but no sound now.
I have tried everything and nothing works.

sound problems:
#Restore speaker icon to System Task bar, right-click on clock or tray > Properties > Volume: On
#Click on the Sound icon in System tray then on Mixer, make sure Firefox is not muted [http://dmcritchie.mvps.org/icons/fx_sound.png picture]
<p>Additional references
* [https://support.mozilla.com/en-US/kb/No%20sound%20in%20Firefox No sound in Firefox | Troubleshooting | Firefox Help]
* [http://support.mozilla.com/en-US/kb/Video%20or%20audio%20does%20not%20play Video or audio does not play | Troubleshooting | Firefox Help]
* [http://kb.mozillazine.org/Video_or_audio_does_not_play Video or audio does not play - MozillaZine Knowledge Base]

I dropped my iPhone 4 in the sink where it was submerged in water for not even 2 seconds I took it out and put it in a warm room by the radiator and most of it works but no sound and battery length is short and runs out quickly. Any ideals on how to help?

I dropped my iPhone 4 in the sink where it was submerged in water for not even 2 seconds I took it out and put it in a warm room by the radiator and most of it works but no sound and battery length is short and runs out quickly. Any ideals on how to help?

$149
They do not repair .Apple exchange and all returned units are refurbished at The Apple plants in China
So you get a device that looks like and functions like new
Are you familiar with the results of water and electricity mixing

HT5517 video is working but no sound in airplay

I have an Apple Tv both 2nd and 3rd generations. My vidoe is working but no sound when trying to play a video from my Iphone. I use Airport express for wi-fi. I am able to do everything else with Apple TV.

Welcome to the Apple Community.
Try the following steps, check whether things are working after each step where appropriate, before trying the next.
    1.    Check AirPlay is turned on on the Apple TV (turn it off and on if it already is)
    2.    Check that both devices are on the same network (Settings > Wifi, on the mobile device and Settings > General > Network, on the Apple TV).
    3.    Restart the Apple TV (Settings > General > Restart).
    4.    Restart the Apple TV by removing ALL the cables for 30 seconds.
    5.    Restart your router.
    6.    Restart your mobile device.

Speakers work but no sound

Speakers work but cannot get any sound output. Running windows 7 on Intel iMac. Speakers sound on booting and graphics in Control panel and on toolbar indicate sound is being recieved but nothing comes out of speakers or headphones.

This is your machine - http://www.everymac.com/systems/apple/imac/specs/imac-core-2-duo-3.06-24-inch-al uminum-early-2008-penryn-specs.html
It is an iMac from 2008. You can download the .zip file directly to a new folder on the Windows side, unzip it and run setup.exe from this folder.
This is what you need - Boot Camp Support Software 4.0.4033. (From System Requirements).
Post Date: Mar 14, 2013
File Size: 601.76System Requirements
MacBook (13-inch, Late 2006)
MacBook (13-inch, Mid 2007)
MacBook (13-inch, Late 2007)
MacBook (13-inch, Early 2008)
MacBook (13-inch, Late 2008)
MacBook (13-inch, Early 2009 & Mid 2009)
MacBook (13-inch, Late 2009) *
MacBook (13-inch, Mid 2010) *
MacBook Air (13-inch, Early 2008)
MacBook Air (13-inch, Late 2008 & Mid 2009)
MacBook Air (11-inch & 13-inch, Late 2010) *
MacBook Pro (15-inch & 17-inch, Core 2 Duo)
MacBook Pro (15-inch & 17-inch, 2.2 & 2.4GHz)
MacBook Pro (15-inch & 17-inch, Early 2008) *
MacBook Pro (15-inch, Late 2008) *
MacBook Pro (17-inch, Early 2009 & Mid 2009) *
MacBook Pro (15-inch, Early 2009) *
MacBook Pro (13-inch and 15-inch, Mid 2009) *
MacBook Pro (13-inch,15-inch, and 17-inch, Mid 2010)
MacBook Pro (13-in, 15-inch, and 17-inch, Early 2011 & Late 2011)
Mac Pro (Mid 2006)
Mac Pro (Early 2008) *
Mac Pro (Early 2009)
Mac Pro (Early 2007)
Mac Pro (Mid 2010)
Mac Pro (15-inch and 17-inch, 2.2 & 2.4GHz)
Mac mini (Mid 2007)
Mac mini (Early 2009 & Late 2009)
Mac mini (Mid 2010) *
iMac (17-inch, Late 2006)
iMac (20-inch, Late 2006)
iMac (24-inch, Late 2006)
iMac (20-inch & 24-inch, Mid 2007)
iMac (20-inch & 24-inch, Early 2008)
iMac (20-inch, Early 2009 & Mid 2009)
iMac (21.5-inch & 27-inch, Late 2009) *
iMac (27-inch, Late 2009) *
iMac (21.5-inch, Mid 2010) *
iMac (27-inch, Mid 2010)
iMac (21.5-inch, Mid 2011 & Late 2011)
iMac (27-inch, Mid 2011)
all these drivers support Windows 7, 32 bit
* drivers that support Windows 7, 32 and 64 bit

Transitions work but no sound?!?

I have a Power Point with animated GIF's, custom animations
with sounds assigned, and transistions with sounds assigned. When I
play the slide-show in Power Point everything functions fine but
when I publish it using presenter the animations and transitions
work but there is no sound and the animated GIF's only show up as a
still graphic. Any suggestions?

Not only that Taz, but here's something else to consider:
If you're using Breeze 5.1, animated .gifs aren't supported.
Although I can't speak for Presenter 6.0 users yet (still waiting
on my upgrade), I've heard that animated .gifs do work in that
environment.
Last note...and this really should be something everyone
needs to consider when crafting decks/presentations with the
intention of publishing...Just because you can make certain things
happen while editing and displaying in PowerPoint (including slide
show mode or F5), that doesn't necessarily mean that things will
STILL work when you publish your content.
Various facets of what you could normally get away with in
Powerpoint simply don't convert well (if at all), especially with
things like custom animations and Action Buttons. And although most
of those "bugs" have been documented I still think we, as users,
need to keep putting the heat on Adobe to improve what they have,
because the reality is that there are a BUNCH of other products
that can do what Breeze/Presenter does, and in some cases, cheaper.
That said, however, I also realize that the list of things
that don't work really isn't that long at all...but better to test
as you build rather than forcing yourself into a bad situation when
it's too late.

Speaker works, but no sound when using iPhone handset and no typing sounds

Hello, This is the 2nd time this has happened to my iPhone in the last month...
When I type a text message, lock the phone, slide to unlock the phone, start up the phone, use the iPhone itself to talk to someone on the phone, etc - the sound does not work...
It does work using the bluetooth headset and it also works on speaker phone (I am able to hear my calls). The ringer for my alarm clock works, but not when someone calls me. The ipod is not working either - I am unable to hear songs.
The silence switch is not turned on (on the side of the phone) and I've checked the other settings as well... I also restored my phone last night hoping that might work and I've reset the settings on the phone as well...
Can anyone please help me with this issue?
Thanks!

Did this occur after using the earbuds?
Try inserting and removing the earbuds several times in a row.

Logitech USB headphones - microphone works but not sound output

Seems like the sound output to my Logitech USB headphone has stopped. The microphone inputs but the sound output is blocked. Could be technical issue with the set but was wondering of anyone else has this problem after the last update to 10.14.0

ChickInVici,
Having similar issue with iPad 2. No volume on Apps or Music (except when using headphones). Just started happening after months of no issues. Have reset/ restored with no solution. Can you provide more detail with your solution? I went to >settings>accessibility>voiceover.....but could not find headphones etc... what am I missing. Could you be more specific on what you changed to resolve your issue.
thanks

My sub works but no sound plz help audigy

i have audigy 2zs and 5. sicuro all works but sub

Go to the EAX panel and shut off all effects, then run the speaker tests. Also, I found (Using an O-scope checking the voltage levels of a properly terminated channel) that the output voltage level of the subwoofer channel is 20% of the other 5 channels.
My solution was to spend $50 and buy an ARTcessories HEADAMP and some cables/adapters to give it some gain. Even with the?HEADAMP maxed, I'd like more so I could shake the floor apart with my 0W RMS/CH Peavey amps and JBLs. Very close to happy.
Got some 60 cycle hum out of the 2zs card (very, very low) I can't get rid of though. Even after attaching EVERYTHING (but the mouse and keyboard) to the master grounding block for the entire house with individually run #0 wires. Even when the PC is off. Interesting.

My Ipod touch recently fell into water, but once dried, it worked with seemingly little to no problems. Today, after working for at least an hour, the screen froze and is now not working, but the sounds are still functioning.

I accidentally dropped my Ipod into the lake, at the beach yesterday, but i caught it early and it wasn't too soaked... i wiped it off for the most part, and most of the buttons and the screen worked fine! i was shocked, and there were a few glitches with the camera and the slide button on the lock screen, but otherwise it was greatly intact! so i gave it a rest, put it in my purse, and picked it up fifteen minutes later, and it was working 100% normally again! when i got home a few hours later, i put it in rice for a few hours, taking it out every once and a while to check my notifications... it still seemed to be working perfectly, so i just set it down out of the rice, assuming the moisture was gone. this morning, again, everything was working normally, no glitches, UNTIL, i opened my instagram app, and the screen froze, and it seemed like it had two separate screens, and i held the Sleep button down until the screen went black... then i tried turning it back on, etc. and it still didn't work, and so i plugged it into the computer, holding down the sleep and home buttons, and itunes identified it as in recovery mode, and started updating. i tried again to press the sleep and home butttons, maybe pressing only the home button, because I heard the Siri noise, as well as the charging sound, but the screen was still black.... i checked my iTunes, and lo and behold, it had identified my iPod, and synced it to the computer, as if it were normally functioning. However, the screen is still not working, and Siri is not working either. The sounds may be the only thing that's functioning. Should i send it in?

- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar
Apple will exchange your iPod for a refurbished one for $199 for 64 GB 4G, $99 for the other 4Gs, $99 for the 16 GB 5G and $149 for the other 5Gs. They do not fix yours.
Apple - iPod Repair price
Sometime it takes a little while for the water to damage the iPod.

IPod working, but no sound

I have a 30gb video ipod. Up until about 2 weeks ago, I used it with great results in my car, with an itrip and at home on an iboom. Then it just stopped working. The strange thing is, it is not a hardware problem, because when I connect it to either of those, or to my PC, it recognizes and charges the ipod. The ipod lights up as if it is ready to play, but if I put a song on, no sound comes out. Just to be safe, I tried my friend's ipod on both and it worked fine. It also doesn't work with headphones
I ran diags on my ipod and everything is fine. I have reset the ipod. I have updated my software to 1.2.1 on the ipod and 7.3 itunes. I wasn't really looking forward to restoring it, but when I realized that was all that was left, I did it.....no help. Still not working.
The "genius" in the apple store said he has never seen anything like this before. I have an appointment with another genius on Monday, but I was hoping maybe you guys would have an answer for me....I have always had more luck here than anywhere else.
My warranty ran out 2 weeks ago, but I had forgotten to extend the apple care, so I am probably screwed, right?
Has anyone ever heard of this happening?
Thanks in advance for your help.
Nicki

Thanks Deggie,
I see no signs of damage. It is also not working with my headphones and it charges ok, so I figured it couldn't be the pins...which had been my first assumption.
I went to a couple 3rd party places online to see if they knew what it could be and got 3 different answers....headphone jack (which I know it isn't), system board and logic board. I have an appt tomorrow with the apple store, so I'll see what they say it is and then buy and fix the part myself. I did that with my old nano and it is alot easier than I thought it would be. Since my apple care is up (2 weeks ago, of course) it will be cheaper this way.
Stupid question coming, but whatever....logic board and system board are both differnt things right? Cause when I go online to see prices, most sites have one or the other, but I haven't found a site that sells both, which is starting to make me think they are the same thing.
Thanks Again for any info...
Nicki

My video recording sounds not working but other sounds are working fine, I've tried clearing the little mic thing near my earphone hole and had no success can someone please help me out?

hhi guys
my video recording sounds not working at all but it's working for other things such as music. I've tried to clear my sound thing near the earphone hole but had no success can someone please help me out?

Had an Iphone 4 for about 3 months now. This happened to the first one I had and they ended up having to replace it at the apple store just a couple weeks ago 6/2. It happened again last night to my new one. This time i was able to correct it by going to itunes, backing up the phone to icloud, and then restoring the software. Mine did not work with voice memo, but did work with headphones plugged in, and would also work on speaker. I could hear callers but they couldn't hear me. I had purchased a new case (lifeproof case at $79.99) because it comes with plugs that cover the headphone jack, and the charging port, and is also waterproof. I heard that the root cause is due to lint, dirt, etc getting inside the headphone jack. Well, must be something else. It's a 10 days old phone, and has been in this overpriced case the whole time, and I have not used the headphones. I hope this doesn't keep happening.

Viewsonic VX2453MH-LED Display Works, but no sound from monitor

I'm using 15" MBP (early 2011), OS X Lion, and I saw earlier threads about this disaply not working (vertical bars). I figured that part out, but am having trouble with no sound coming from the built-in speakers. I have a Moshi HDMI adapter and ViewSonic's HDMI cable. I have no sound, though, and I even put in their supplied audio cable into the headphone jack, which didn't work. Maybe I need s/t else? I love the monitor and not having the sound won't kill me, but I did get it because it was primarily integrated into one whole unit. Thoughts would be greatly appreciated! Btw, called Viewsonic and they were no help.

After I click on playback devices and bring up the Sound window, I can see the monitor icon with the label Realtek HDMI Output, as well as icons for Realtek Digital Output, Speakers, and Headphones. Speakers and Headphones are greyed out since they are not plugged in. Realtek Digital Output is not greyed out and says Ready. The monitor icon is also not greyed out, has the check mark on a green circle background, and is marked as the Default Device. Since it is already set as the default device, the Set Default button is greyed out. When I double click Realtek HDMI Output and open the Realtek HDMI Output Properties window (Item 6 on the checklist) and click the Supported Formats tab (Item 7), there are no check boxes next to the choices under sample rates, but the various rates are there: 44.1 kHz, 48.0 kHz, 96.0kHz, and 192.0 kHz. The box for Encoded Formats just says: No compressed formats found. There doesn't appear to be a way to select a particular sample rate among the four that are listed. I've tried clicking and right clicking on 48.0 kHz with no effect, and the apply button remains greyed out regardless. Clicking on ok or cancel also makes no difference.
Really frustrating .....

Videos work but no sound

i am able to put videos on my ipod but there is no sound when i listen to them!!! help please!!!

I tired this and it worked:
Adobe Flash Player plug-in
https://support.google.com/chrome/answer/108086
Adobe Flash Player is directly integrated with Google Chrome and enabled by default. Available updates for Adobe Flash Player are automatically included in Chrome system updates.
If you want to use Adobe Flash Player in other browsers, you’ll need to separately download the Adobe Flash Playerfor those browsers.Enable or disable Adobe Flash Player
These instructions apply to Google Chrome on Windows, Mac, Linux, and Chrome OS.
Type chromelugins in the address bar to open the Plug-ins page.
On the Plug-ins page that appears, find the "Flash" listing.
To enable Adobe Flash Player, click the Enable link under its name.
To disable Adobe Flash Player completely, click the Disable link under its name.
Note: If you've previously installed Adobe Flash Player separately, you'll see two files listed for the plug-in. If both are listed as enabled, the version bundled with Chrome will be used. To enable a specific version of Adobe Flash Player, clickDetails in the upper-right corner of the page. Then click the Enable link for the version of Adobe Flash Player you want to enable. The table below shows the filename for the version that is integrated with Google Chrome. more at the link above .....

I just installed quicktime 7.7.2 to watch movie trailers, works but no sound

I just installed quicktime 7.7.2 to watch movie trailers on http://trailers.apple.com/trailers. It plays the trailers OK but there's no sound. Any ideas? I have Windows XP.
Quicktime installation also changed the association on an m4v movie that played perfectly with the VLC movie player, but plays real jerky with the QT player and also there's no sound. Any ideas?
Thnx

I just installed OuickTime 7 Pro in my Mac Pro Ver 10.6.8. The video I am trying to view is codec h264 Compression dvcpro 50 hd. I have audio but no video. It says I need other software with QuickTime for it to work. Dose anyone know what I need?
H.264 video should be supported by your basic Snow Leopard operating system. The DVCPRO HD family of codecs is part of the Apple "Pro" codecs package which is normally installed as part of a "Pro" video editing suite installer or contemporaneously installed separately as part of one of the newer pro editing apps like FCPX. if you already have one of these pro suites or apps installed or available, then re-install the correct codec package that is missing. If not, you will need to purchase a Pro suite or app to be able to install the required codec package.

JVC KD-R200 Radio works but no sound?

Similar Messages

Maybe you are looking for