JVM Error 547 - Flash Write Failed

Hi, i got the 547 error after a long way of many other errors, it start by installing a new app using the stupid DM and my BB restart after the installation and i got 507 error, which mean no software, so i doubt it and tried to pull the battery, sim card and SD, wait for some time, return the battery, and 561 error was there, tried again and nothing
after search on crackberry and blackberry forums, talking about JL and BBSAK, used both to wipe and re-install the OS again,
of course i remove the vendor.xml from common files and user "document and settings" folders
during the installation it load until the net_rim_cldc.cod and restart on its own, and the loader give an error not able to connect again, so i wait until my phone restart with error 507 and click on retry, it stupidly erase every thing again instead of continue from the stop point and it reach the same point and restart, so i fall in a loop
i tried to delay the net_rim_cldc.cod to the end by changing the Platform.alx, and i tried to cancel this file from Platform.alx and it stuck with the truetype font.cod
i remove this OS and i tried to download from a different service provider, "again of course i remove the two files for vendor.xml" but no use
then i used the BBSAK to add manually all the basic files which is 220 modules, and i left the net_rim_cldc.cod to the end, suddenly my phone try to start and keep restarting every 2 minutes, and after several attempts is give me the JVM Error 547 "flash write failed"
no i cannot connect to BBSAK, the only way is to connect to the loader without battery and wait until it finish erasing then i can connect to JL to wipe or BBSAK
but then what?? i will end up between BB apploader which cannot finish the installation and BBSAK which can put the 220 files in 220 steps and the phone will not load
now, any BB genius can help??

Hi maytik and welcome to the BlackBerry Support Community Forums!
Take a look at this article as it should help get you back up and running again:
KB11320 - How to perform a clean reload of the BlackBerry Device Software using BlackBerry Desktop M...
Hopefully that helps!
-CptS
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Similar Messages

BB- pearl 8100 - JVM error 547

Hi,
I have Blackberry 8100 pearl model, it is giving me following error message ( even after hard restart, this msg appears as soon as i insert the battery):
JVM ERROR 547
flash write failed: p=827a0000,s=4.
I downloaded the version 4.2.2 desktop manager from the below link:
http://na.blackberry.com/eng/support/downloads/download_sites.jsp
After installing the new DTM ver 4.2.2, I performed the points mentioned in this link
http://www.blackberry.com/btsc/search.do?cmd=displayKC&docType=kc&externalId=KB10144&sliceId=SAL_Pub...
But when i try this , it fails in step 4, that is, I am not able to see any applications listed. It is displaying this message:
" The BlackBerry desktop software does not have BlackBerry Device software for the device that you have connected to the computer. Contact your wireless service provider or system administrator."
I have not taken any back up of my phone, so i dont want to loose my data esp the contact list and messages. Earlier I had version 4.2.0.10 deskop manager now even after upgrading it to 4.2.2 it didnt help .
I also tried selecting secure mode and reset but it didnt help.
Please help me to recover. I shall be extremely thankfull.
PS: I am new to this forum, not sure If I am posting at right place, please redirect me to the correct thread if I am wrong.

Hello jamin
The first thing here is that your data is most likely already lost
Second, have you downloaded your device software? The device software is different from the
Desktop Manager software.
If you have not downloaded your device software you will need to do this and
install it on the computer. I suspect
this is the reason you are getting " The BlackBerry desktop software
does not have BlackBerry Device software for the device that you have connected
to the computer. Contact your wireless service provider or system
administrator."
To get the device software you will need to go back to the carrier site and
download it.
If you tell me who your carrier is I can get you the download link.
Once you have the device software you are going to want to follow the below
KB article
http://www.blackberry.com/btsc/microsites/search.do?cmd=displayKC&docType=kc&externalId=KB11320&slic...
Hope to hear from you soon!
-SR
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Jvm error 547

Good morning, I have a blackberry pearl and on the screen has appeared the following message "JVM Error 547 flashes write failed Scroll for available commands." with under different options among which Continuous, Reset, Attach Debugger, Breakpoint, Catfail, Delete Fixups, Delete Modules, Delete Persistent Objects, Dump Logged Stack Traces...
What must I do?
Thanks

Hi there!
You've posted this three times...that is not encouraged as it takes away from other who need help while we spend time duplicating (or triplicating) efforts for you. Please choose one of your threads to work in and mark the others as solved.
Cheers!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

JVM Error 547 - Can't load OS

I have a Blackberry 8120 and it keeps getting the JVM Error 547 with the only option to reset. I tried loading a fresh install of the OS but it get's to the point of loading the first .cod file and it resets itself. I've also tried using just the app loader and not the Desktop Manager but get the same problem. I've tried downgrading the OS but get the same problem. I've also tried a custom app called "BBSAK" but I get the same problem.
Help! I've searched the net and tried a bunch of things but nothing seems to work! Is the blackberry fried?

Turns out it was the ribbon.

KQRCMT: Write failed with error=604 Errors in Trace File

Anyone know what errors like these in the trace file might indicate? I'm trying to diagnose why one of our application processes died without warning, and found this in the process trace file right about the time when it died. My Oracle Support turns up very few hits, none of them helpful. Google likewise had very little to say on the matter.
Also there were no errors thrown in the alert log during the time indicated in the trace file messages.
*** 2011-02-01 14:30:29.976
*** MODULE NAME:() 2011-02-01 14:30:29.976
*** ACTION NAME:() 2011-02-01 14:30:29.976
KQRCMT: Write failed with error=604 po=0xa68636878 cid=13
diagnostics : cid=13 hash=7ad19577 flag=2a
KQRCMT: Write failed with error=604 po=0xa68636878 cid=13
diagnostics : cid=13 hash=7ad19577 flag=2a
*** 2011-02-01 14:30:33.416
KQRCMT: Write failed with error=604 po=0xa68636878 cid=13
diagnostics : cid=13 hash=7ad19577 flag=2a
*** 2011-02-01 14:30:35.343
KQRCMT: Write failed with error=604 po=0xa68636878 cid=13
diagnostics : cid=13 hash=7ad19577 flag=2a
KQRCMT: Write failed with error=604 po=0xa68636878 cid=13
diagnostics : cid=13 hash=7ad19577 flag=2a
*** 2011-02-01 14:30:36.572
KQRCMT: Write failed with error=604 po=0xa68636878 cid=13
diagnostics : cid=13 hash=7ad19577 flag=2a
*** 2011-02-01 14:30:38.684
KQRCMT: Write failed with error=604 po=0xa68636878 cid=13
diagnostics : cid=13 hash=7ad19577 flag=2a
*** 2011-02-01 14:30:39.316
KQRCMT: Write failed with error=604 po=0xa68636878 cid=13
diagnostics : cid=13 hash=7ad19577 flag=2a
*** 2011-02-01 14:30:40.575
KQRCMT: Write failed with error=604 po=0xa68636878 cid=13
diagnostics : cid=13 hash=7ad19577 flag=2a
...etc, etc...Thanks.

Hi All ,
MY database is oracle 11G , SParc OS 64 Bit , i got the same error on my primary database.
Please find the exact error below :
KQRCMT: Write failed with error=604 po=3ebb848b0 cid=13
diagnostics : cid=13 hash=d906a6b flag=2a
KQRCMT: Write failed with error=604 po=3ebb848b0 cid=13
diagnostics : cid=13 hash=d906a6b flag=2aThat is the only error in the trace file.
i have checked on google and metalink but not much is available.
please suggest
Thanks
Kk
Edited by: Kk on Apr 8, 2011 5:19 AM

Linux and PCI-485/8. Write failed:Input/Output error

i am running red hat linux and installed my pci-485/8 serial card. actually, the machine is dual boot with windows nt 4.0 and the card works fine under nt. i followed all the instructions in the ni document "notes to users" entitled "using pci serial with linux". when i finally run serialtest i just get the error message above: Write failed:Input/output error.
not much to go on. any advice???

There are few things that we can try to trouble shoot this problem.
Try uninstalling driver for Win NT completely and reinstalling driver for Linux and see whether that solves the problem.
If that doesn't solve the problem then try using a different Linux machine ( if you have access to ) for the same card. The card works under Win NT that means card is fine and there is no hardware issue associated with this problem.
Try recompiling your serialtest.c :
Enter the following to recompile serialtest.c and rerun serialtest.
(Also, the source code for serialtest is available for editing and viewing
at serialtest.c, provided in the PCI-SERIAL directory.)
linux PCI-SERIAL# gcc serialtest.c -o serialtest
linux PCI-SERIAL# ./serialtest < receive port numbe
r>
< transmit port number>
If serialtest hangs:
Make sure the interface is seated correctly and tighten the screw that holds
the interface in place. Also, make sure the cables are attached to the correct
ports. In some cases, serialtest hangs if the transceiver modes
(PCI-485) are not set. Try setting both transmit and receive ports to
transceiver mode 0 (Four-Wire Mode).
linux# ./rs485 < transmit port number> 0
linux# ./rs485 < receive port number> 0
linux# ./serialtest < receive port number> < transmit port number>
See the attached file for more information.
Attachments:
322539a.pdf ‏138 KB

Windows XP SP3 and Time Capsule Delayed Write Failed

I am having difficulty getting my MacBook Pro to back up to my Time Capsule.
TC is 1TB.
Works fine with OSX.
XP SP3 on wireless network allows full internet access and print sharing and also allows very small backups (i.e. one or two documents in a folder) without a problem.
When I try to do a few folders (let alone a full back up) I get an error - Windows delayed write failed.
As I can do small backups I think that this rules out a problem communicating with the TC and also any issues with the formatting of the drive (I have left it as it came from apple - although a right click on the drive states FAT32).
I have a poor work around which is to use Macdrive to mount my OSX disc and backup to that. Reboot into OSX and let time machine take care of the rest.
Very messy but also rules out a size problem and I suspect that this also rules out any problems with the backup utility (Microsoft XPs own)as I don't get the same error with this "networked" drive
I have spent some time looking for ways to fix this and the windows support site suggested disabling a cache option under properties if you right click the drive. This option is not available for the TC as properties only give you information on the free space.
I am now at a loss as to what to do to make this work

Kappy,
Thanks for taking to time to reply.
I don't believe that the TC is FAT32 formated as it is working fine with OSX and I have not formated the drive from how it shipped from apple - which I guess is Mac OS Extended as you described - Have just checked and it is indeed Mac OS Extended (Case-sensitive, Journaled)
What you suggest with winclone is effectively what I am doing using MacDrive (which allows me to mount the OSX disc in XP and write directly to it).
Is there not a way to back up straight from XP without going via OSX (the literature on TC would suggest this is possible).
I had looked at retrospect to use as a backup instead of XPs own but think I will have the same problem with disc caching. It is not that I cannot write to the TC (as I can in small sizes) its just that I get the error delayed write failed if I try to do a full back up.
Message was edited by: Juan Quirk

HELP: flarcreate fails with ERROR: unable to write archive

Greetings,
Having trouble trying to create flar file.
I am using the following syntax, but the -X seems to be ignored and I can't find what the format for that file should be.
appdev03 # flarcreate -n appdev03 -S -H -a "author" -X /tmp/exclude /tools/appdev03.flar
Full Flash
Checking integrity...
Integrity OK.
WARNING: fdo: Ignoring duplicate filter entry. Choosen entry will be: /opt/orca/var -
WARNING: fdo: Ignoring duplicate filter entry. Choosen entry will be: /opt/orca/var -
Running precreation scripts...
Precreation scripts done.
Creating the archive...
cpio: "var/tmp/21502_00000001" ?
cpio: "var/tmp/28914_00000001" ?
cpio: "var/tmp/28939_00000001" ?
cpio: "var/tmp/26624_00000001" ?
cpio: "var/tmp/26627_00000001" ?
cpio: "var/tmp/04733_00000001" ?
cpio: "var/tmp/29298_00000001" ?
cpio: "var/tmp/13627_00000001" ?
cpio: "var/tmp/13628_00000001" ?
cpio: "var/tmp/02531_00000001" ?
cpio: "var/tmp/02532_00000001" ?
cpio: "var/tmp/04735_00000001" ?
cpio: "var/tmp/xsauthn" ?
cpio: "var/tmp/27491_00000001" ?
cpio: "var/tmp/08868_00000001" ?
cpio: "var/tmp/08869_00000001" ?
cpio: "var/tmp/20269_00000001" ?
cpio: "var/tmp/20270_00000001" ?
cpio: "var/tmp/27492_00000001" ?
cpio: "var/tmp/xsauthz" ?
cpio: "var/tmp/16103_00000001" ?
cpio: "var/tmp/16104_00000001" ?
cpio: "var/tmp/29964_00000001" ?
cpio: "var/tmp/03913_00000001" ?
cpio: "var/tmp/09305_00000001" ?
cpio: "var/tmp/10454_00000001" ?
cpio: "var/tmp/10505_00000001" ?
cpio: "var/tmp/07839_00000001" ?
cpio: "var/tmp/08129_00000001" ?
cpio: "var/tmp/00574_00000001" ?
cpio: "var/tmp/00694_00000001" ?
cpio: "var/tmp/05611_00000001" ?
cpio: "var/tmp/05612_00000001" ?
cpio: "var/tmp/01281_00000001" ?
cpio: "var/tmp/06672_00000001" ?
cpio: "var/tmp/06674_00000001" ?
cpio: "var/tmp/14242_00000001" ?
cpio: "var/tmp/14243_00000001" ?
cpio: "var/tmp/13904_00000001" ?
cpio: "var/tmp/13924_00000001" ?
cpio: "var/tmp/25133_00000001" ?
cpio: "var/tmp/25159_00000001" ?
cpio: "var/tmp/27648_00000001" ?
cpio: "var/tmp/27649_00000001" ?
cpio: "var/tmp/29284_00000001" ?
cpio: "var/tmp/29287_00000001" ?
cpio: "var/tmp/12637_00000001" ?
cpio: "var/tmp/12640_00000001" ?
cpio: "var/tmp/13947_00000001" ?
cpio: "var/tmp/03944_00000001" ?
cpio: "var/tmp/03945_00000001" ?
cpio: "var/tmp/13950_00000001" ?
cpio: Error with fstatat() of "opt/appworx/log/RmiServer1106141450.log", errno 2, No such file or directory
cpio: Error with fstatat() of "opt/appworx/log/RmiServer1106141440.log", errno 2, No such file or directory
22708784 blocks
54 error(s)
Unable to write archive file.
ERROR: Unable to write archive.
my -X file /tmp/exclude is as follows, yet it seems ignored:
appdev03 # more /tmp/exclude
/var/tmp/.oracle
/var/tmp/[0-9*]
/var/tmp/xsauthz
/var/crash
/tlg
/tacp
/depot
/tools
/toolsdb
/development
/opt/orca/var
/usr/local/CAcrypto/cacrypto_solaris.tar
/usr/local/CAcrypto/cacrypto_sun4_solaris.tar
/usr/local/CAcrypto/cacrypto.tar
/var/opt/oracle/jre/jre.tar
/var/opt/oracle/oraInventory.09252003.tar
/var/opt/oracle/oraInventory.10212003.tar
/var/opt/oracle/oraInventory.11032003.tar
/var/opt/oracle/jre.tar
/opt/ca/harvest/harvest.tar
/opt/ca/harvest/tomcat55/apache-tomcat-5.5.20.tar
/opt/ca/harvest/tomcat55/apache-tomcat-5.5.20-compat.tar
/opt/ca/caiptodbc/odbc511.tar
/opt/appworx/UWClient/web/images.tar
/opt/appworx/jre.tar
/opt/appworx/apache.tar
/opt/appworx/apache_dev.tar
/opt/appworx61/jre.tar
/opt/appworx61/apache.tar
/opt/appworx61/AWjars.tar
/opt/appworx61/AWutil.tar
/opt/appworx61/install/v61/apache.tar
/opt/appworx61/install/v61/awjars.tar
/opt/appworx61/install/v61/awutil.tar
/opt/appworx61/install/v61/jre.tar
/opt/appworx/log/RmiServer1106141450.log
/opt/appworx/log/RmiServer1106141440.log
/emc/2312fcode_2_00_6.tar
the file is there but not sure of its accuracy:
appdev03 # flar -i appdev03
files_archived_method=cpio
creation_date=20110621221025
creation_master=appdev03
content_name=appdev03
creation_node=appdev03
creation_hardware_class=sun4u
creation_platform=SUNW,Netra-T12
creation_processor=sparc
creation_release=5.9
creation_os_name=SunOS
creation_os_version=Generic_118558-39
files_compressed_method=none
content_author=author
content_architectures=sun4u
type=FULL
system is Solaris 9 04/03 with Generic_118558-39 V1280.
plenty of space in the directory being written to and I can touch a file there as well.
Any advise is appreciated, thanks.
Jeff
Edited by: user13021352 on Jun 21, 2011 3:40 PM

What report is it ?
Did you try and search metalink ?
How to handle 'ORA-01652: unable to extend the temp segment by 128 in tablespace' error messages? (Doc ID 1359238.1)
R12 Journal Entries Report (XLAJELINESRPT) Has Performance Issue Or Fails With Error: "java.sql.SQLException: ORA-01652: unable to extend temp segment by 128 in tablespace TEMP1" (Doc ID 1141673.1)
This forum may be the right one for your question - General EBS Discussion

IPod won't sync, gives 'Delayed Write Failed' error.

I've had my iPod classic 80gb, for roughly a year now, and I never really had any permanent issues with it, until last week. I plugged it into my laptop and left it on over night. I wake up in the morning and all my songs and videos were gone. iTunes was reading the data as 'Other'. Overnight, without me doing a single thing, everything was gone. I unplugged it and plugged it back in, and all the files were gone. Completely. Space had been returned.
I painstakingly put my songs back in that afternoon. The next day, I plugged the ipod into my office computer, and tried to sync my podcasts. After syncing about 20 files, iTunes froze. Then a yellow bubble popped up saying 'Delayed Write Failed' after which it wipes out everything I was able to sync.
I've done everything, from restoring the ipod, to re-installing iTunes to formatting the disk to straight up performing a chkdsk. As i speak right now, my laptop won't boot up after i performed the last chkdsk, which told me i had a bunch of invalid sectors or some other. For one week, I've searched the net and it seems no-one has a solution to this.
Any help? I don't have an Apple store in my country, and I don't want to believe that i have to get a replacement.

1st - Sorry I can't help you.
I also have iPod Classic 80gb and have had no trouble till two days ago (11/08). I connected my iPod and it showed up as a source in iTunes but none of my music was shown. I reconnected it and same thing, I checked for update for iPod but it said it was up to date. I then used iTunes to restore my iPod to factory settings. It went through the process and restarted but after that would never show up as a source in the iTunes window.
When I connect the iPod to my PC it detects the USB Device as an iPod right way (so it doesn't seem to be a USB Driver issue) but then the "Auto-Play" window shows up and it makes my PC slow way down and then eventually I see the "Windows Delayed Write Failed" error mesage in the task bar. If I check My Computer it shows the iPod as a drive.
I've done everything listed in Apples Support Page for this, from restoring the iPod, to re-installing iTunes, clearing temp folder and old registry files, updating iPod Service in MsConfig. I have also tried to sync the iPod with my other PC and see the same error so it seems the iPod is corrupted. I don't know anyway to restore factory settings again since it won't show up in iTunes anymore. I've searched the net and it seems no-one has a solution to this.

IPod Mini error (Delayed write failed)

Whenever I update songs to my ipod mini it copys about 43 songs until a delayed write failed error message shows up. I'm not able to copy more songs. Any help would be appreciated.

I used to get this error:
http://saltypickles.com/itunes.jpg
I never did fix the problem... it didn't matter witch USB port I used I would get that error, sometimes after 10 songs, sometimes after 200... I couldn't reformat with it either. When I posted here about it, I was told to try Firewire, unfortunaly I didn't have any Firewire ports. So I fought with it until I got the music on it.. then I left it alone and bought an iMac... not suggesting to buy an iMac, but I am suggesting it could be the USB ports on your computer. Could be there are not fast enuf (such as USB 1) or they may not be powered... are you using a USB port from a hub? or on the front of your computer? Make sure you have it plugged into one on the back.

What is this error fatal: Write failed: Broken pipe in log of N7K

<186>: 2015 Mar 24 08:29:27 HKT: %DAEMON-2-SYSTEM_MSG: fatal: Write failed: Broken pipe .Client is 75.121.220.251,length of packet causing error 84 84 - sshd[684]
what is this error fatal: Write failed: Broken pipe in log of N7K
i find many brute force guessing login,
what can we do next?
[7m--More--[27m
iled for user root#02# from 222.186.30.115 - sshd[23714]
[7m--More--[27m
2015 Mar 24 07:17:25 xxxx %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication fa
[7m--More--[27m
iled for user root#02##02# from 222.186.30.115 - sshd[23714]
[7m--More--[27m
2015 Mar 24 07:17:28 xxxx %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication fa
[7m--More--[27m
iled for user root from 222.186.30.115 - sshd[23715]
[7m--More--[27m
2015 Mar 24 07:17:28 xxxx %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication fa
[7m--More--[27m
iled for user root#02# from 222.186.30.115 - sshd[23715]
[7m--More--[27m
2015 Mar 24 07:17:28 xxxx %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication fa
[7m--More--[27m
iled for user root#02##02# from 222.186.30.115 - sshd[23715]
[7m--More--[27m
2015 Mar 24 07:17:31 xxxx %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication fa
[7m--More--[27m
iled for user root from 222.186.30.115 - sshd[23717]
[7m--More--[27m
2015 Mar 24 07:17:31 xxxx %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication fa
[7m--More--[27m
iled for user root#02# from 222.186.30.115 - sshd[23717]
[7m--More--[27m
2015 Mar 24 07:17:31 xxxx %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication fa
[7m--More--[27m
iled for user root#02##02# from 222.186.30.115 - sshd[23717]
[7m--More--[27m
2015 Mar 24 07:17:33 xxxx %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication fa
[7m--More--[27m
iled for user root from 222.186.30.115 - sshd[23718]
[7m--More--[27m
2015 Mar 24 07:17:33 xxxx %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication fa
[7m--More--[27m
iled for user root#02# from 222.186.30.115 - sshd[23718]
[7m--More--[27m
2015 Mar 24 07:17:34 xxxx %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication fa
[7m--More--[27m
iled for user root#02##02# from 222.186.30.115 - sshd[23718]
[7m--More--[27m
2015 Mar 24 07:17:36 xxxx %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication fa
[7m--More--[27m
iled for user root from 222.186.30.115 - sshd[23719]
[7m--More--[27m
2015 Mar 24 07:17:36 xxxx %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication fa
[7m--More--[27m
iled for user root#02# from 222.186.30.115 - sshd[23719]
[7m--More--[27m
2015 Mar 24 07:17:36 xxxx %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication fa

Restrict your vty line logins with an access-list to prevent Internet origin login attempts.

Adobe flash 5.5 jvm error or crash. Solutions?

Hi
i have 2 different problem with Cs5.5
first problem , when i launch flash cs5.5, several time "jvm error" occur. only opening flash , before opening fla!. So i can only close flash, close all the application, restart flash or reboot machine.
i have a I7 with 11 Gb of ram windows 7 64 pro machine. i tried to edit the AppData\Local\Adobe\Flash CS5.5\it_IT\Configuration\ActionScript 3.0\jvm.ini with more ram (768, 1024... 2048) but nothing changed.
second problem, randomly when i close compiled fla, flash cs5.5 "stops to work" with useless error reporting. where i can find error reportin log?
thanks

I put a video together to show what is happening.
http://www.youtube.com/watch?v=4m7RBXP5IVw
The crash happens as the file is opening up. The file hangs for a
second, and then Adobe Flash 5.5 Professional crashes, and then a
crash report appears.
I tested these files on another computer with Adobe Flash 5.5
Professional. Christian Audigier vodka file,
"cavodkabottlemenurev3TEMPLATE.fla," displays the description text
with the "client." "project," "label type." "award," and "project
description." The text right of the headings is not appearing. The
text is supposed to be there. For the "submenu" file, the hover state
does not work over the menu items. This file was created in Adobe
Professional CS 5.5.
I created "cavokdabottlemenu3Template.fla" from a re-saved CS3 which
was from MX 2004. The "preload file is from a Lee Brimelow tutorial.
These files are crashing Adobe Flash Professional 5.5. These files are
not crashing on my laptop with Adobe Flash Professional 5.5 (on a
mac). Now, other files are starting to crash in Adobe Flash
Professional as I try to open them on my desktop computer. I am unable
to open Adobe Flash Professional 5.5 without it crashing on my desktop
computer. It is getting worst.
My desktop computer is new, and I bought it in April.
I reinstalled the software. I changed the Java preference from 64 bit
to 32 bit. I did a hardware check. I did scanned disk, permissions
under disk utility. The memory on my computer is fine. I did a
hardware check. I am frustrated. The software is not working. After 3
to 5 times opening files, the software is still crashing. Now, all of
my fla files are not opening up.
I upgraded from Adobe CS3 to Adobe CS5.5. I bought the upgrade discs
directly from Adobe.
I need help fixing Adobe Flash Professional 5.5. I will send you the files.

Flash CS4 - Images in gallery will not show- TypeError: Error #1034: Type Coercion failed: cannot co

So for my A2 studies I have to make an interactive product using flash. Long story short, I needed to make a flash gallery. I am using the "Zen Gallery Flash Component" and this is my code;
galleryInstance.albums=[ { imagesFolder:"N:\ICT\ICT Unit 10\Prototype 3\images", icon:"4.jpg", items: [ {source:"1.jpg"}, {source:"2.png"}, {source:"3.jpg"}, {source:"4.jpg"}, {source:"5.jpg"} ] }, { imagesFolder:"N:\ICT\ICT Unit 10\Prototype 3\images", icon:"8.jpg", items: [ {source:"6.png"}, {source:"7.jpg"}, {source:"8.jpg"}, {source:"9.jpg"}, {source:"10.jpg"} ] } ]; galleryInstance.build();
The user manual does not specify any more coding is needed (I read all the relevant parts and couldn't find anything). The problem is that my images do not show but when exporting the flash product, the gallery is fully functionon - it seems that it cannot locate my images.
In addition to this, I get multiple Output Errors;
TypeError: Error #1034: Type Coercion failed: cannot convert flash.events::IOErrorEvent@2d09a709 to Error. TypeError: Error #1034: Type Coercion failed: cannot convert flash.events::IOErrorEvent@2d09a709 to Error. TypeError: Error #1034: Type Coercion failed: cannot convert flash.events::IOErrorEvent@2d09a709 to Error.etc..
What am I doing wrong?

I'm not sure, the gallery just appeares to be an SWF.
This is all that came up when I clicked it (I had a look at the parameters and they don't seem to help in the addition of pictures).
There appears to be no forum for this flash component :L

'Write' failed due to: Translation Error.

Hi
I'm trying to convert csv and write to a file using FielAdapters in 11g. While reading input i created .xsd using native builder. and using same for write fileadapter. my flow is ReadFileAdapter-->Receive-->invoke-->writeFileAdapter.
Is this right? when I deploy and run I'm getting
<01-Mar-2013 10:09:23 o'clock GMT> <Error> <oracle.soa.adapter> <BEA-000000> <JCABinding=> ReadInput ReadInputAdapter Service ReadInput was unable to perform delivery of inbound message to the composite default/ReadWriteFile!1.0*soa_40862c80-62ba-4425-b7e6-5fcfb5c5b4e4 due to: faultName: {{http://schemas.oracle.com/bpel/extension}bindingFault}
messageType: {{http://schemas.oracle.com/bpel/extension}RuntimeFaultMessage}
parts: {{
summary=<summary>Exception occured when binding was invoked.
Exception occured during invocation of JCA binding: "JCA Binding execute of Reference operation 'Write' failed due to: Translation Error.
Translation Error.
Error while translating message to native format.
Please make sure that the payload for the outbound interaction conforms to the schema.
The invoked JCA adapter raised a resource exception.
Please examine the above error message carefully to determine a resolution.
</summary>
,detail=<detail>Element not completed: 'TestRoot'</detail>
,code=<code>null</code>}
>
I want to convert csv and write as an xml to output file. can some body help me whats is wrong?
here is my xsd
<xsd:schema xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:nxsd="http://xmlns.oracle.com/pcbpel/nxsd"
xmlns:tns="http://TargetNamespace.com/ReadInput"
targetNamespace="http://TargetNamespace.com/ReadInput"
elementFormDefault="qualified"
attributeFormDefault="unqualified"
nxsd:version="NXSD"
nxsd:stream="chars"
nxsd:encoding="US-ASCII"
>
<xsd:element name="TestRoot">
<xsd:complexType>
<xsd:sequence>
<xsd:element name="TestRecord" minOccurs="1" maxOccurs="unbounded">
<xsd:complexType>
<xsd:sequence>
<xsd:element name="C1" type="xsd:string" nxsd:style="terminated" nxsd:terminatedBy="," />
<xsd:element name="C2" type="xsd:string" nxsd:style="terminated" nxsd:terminatedBy="," />
<xsd:element name="C3" type="xsd:string" nxsd:style="terminated" nxsd:terminatedBy="," />
<xsd:element name="C4" type="xsd:string" nxsd:style="terminated" nxsd:terminatedBy="${eol}" />
</xsd:sequence>
</xsd:complexType>
</xsd:element>
</xsd:sequence>
</xsd:complexType>
</xsd:element>
</xsd:schema>
and csv file
12, John, ryegate, Essex
23, Will, wilow, orlean
I also tried inbuild advane function on invoke activity
ora:doTranslateFromNative(bpws:getVariableData('ReceiveInput_Read_InputVariable'),'xsd/Hello2_8.xsd','Test','DOM')
even this didn't work.
can somebody help me how to write as xml from csv?
Thanks
Edited by: user11132693 on Mar 1, 2013 3:01 AM

whne i use transformer it is xslt which takes only values isn't it? And it writes only valuesNope, xslt can write xml... Actually, I'm not sure if I understand what your question is at the moment... Are you still facing the "Translation Error"? Or do you have a problem with a transformation?
Check this... https://forums.oracle.com/forums/ann.jspa?annID=330

"JCA Binding execute of Reference operation 'Write' failed due to: Translation Error.

Hi, i am trying to read a comma delimited file using an inbound file adapter, i have used a mediator to route records to the outbound file adapter.My input.txt file contains 10 records as Fname,Lname.I have used native format builder to generate xsd. To achieve transformation,in the mediator i have mapped only the Fname from source to traget using a for-each loop.I am trying to publish records in the batches of 2 so i have configured inbound file adapter accordingly.My inbound file adapter reads the first two records and the same is visible at the em console mediator instance(payload), i am even able to see the first two records being transformed in the transformed payload in the mediator instance detail but at the outbound file adapter i get an error saying :
Error during invoking 1-way operation "Write" on target service "writeFile"
Exception occured when binding was invoked. Exception occured during invocation of JCA binding: "JCA Binding execute of Reference operation 'Write' failed due to: Translation Error. Translation Error. Error while translating message to native format. Please make sure that the payload for the outbound interaction conforms to the schema. ". The invoked JCA adapter raised a resource exception. Please examine the above error message carefully to determine a resolution.
When i map both the Fname and Lname in the xsl map file i get the output.But i only need one field at the outfile i:e either the Fname or the Lname.
Given below are the details of the interface:
My Interface Flow:       InboundFileAdapter--------ReadsFile------->Medaitor------Transformation----->OutboundFileAdapter-----writesFile
Input Payload(comma delimited text file) as,
Brad,Pitt
Keanu,Reaves
Martin,Lawrance
Johnny,Depp
etc
etc
Schema definition for payload:
<?xml version="1.0" encoding="UTF-8" ?>
<xsd:schema xmlns:xsd="http://www.w3.org/2001/XMLSchema"
            xmlns:nxsd="http://xmlns.oracle.com/pcbpel/nxsd"
            xmlns:tns="http://TargetNamespace.com/readFile"
            targetNamespace="http://TargetNamespace.com/readFile"
            elementFormDefault="qualified"
            attributeFormDefault="unqualified"
            nxsd:version="NXSD"
            nxsd:stream="chars"
            nxsd:encoding="US-ASCII">
<xsd:element name="Root-Element">
    <xsd:complexType>
      <xsd:sequence>
        <xsd:element name="Employee" minOccurs="1" maxOccurs="unbounded">
          <xsd:complexType>
            <xsd:sequence>
              <xsd:element name="Fname" type="xsd:string" nxsd:style="terminated" nxsd:terminatedBy="," nxsd:quotedBy=""" />
              <xsd:element name="Lname" type="xsd:string" nxsd:style="terminated" nxsd:terminatedBy="${eol}" nxsd:quotedBy=""" />
            </xsd:sequence>
          </xsd:complexType>
        </xsd:element>
      </xsd:sequence>
    </xsd:complexType>
</xsd:element>
</xsd:schema>
XSL Map:
<xsl:template match="/">
    <imp1:Root-Element>
      <xsl:for-each select="/imp1:Root-Element/imp1:Employee">
        <imp1:Employee>
          <imp1:Lname>
            <xsl:value-of select="imp1:Lname"/>
          </imp1:Lname>
        </imp1:Employee>
      </xsl:for-each>
    </imp1:Root-Element>
</xsl:template>
</xsl:stylesheet>
Please help me with the above mentioned error and if above transformation is possible using a mediator instead of BPEL
Regards,
Saif

Hi Saif, Are you using the same xsd for the outbound (write) file adapter as well? In that case, you may need to map both the names (Fname and Lname) but leave the name which you do not want to be written to the file as an empty text. For example, if you would need to map only the Lname, but not the Fname, the xsl will be like,
<xsl:template match="/">
    <imp1:Root-Element>
      <xsl:for-each select="/imp1:Root-Element/imp1:Employee">
        <imp1:Employee>
          <imp1:Fname>
          <xsl:text disable-output-escaping="no"></xsl:text>
          </imp1:Fname>
          <imp1:Lname>
            <xsl:value-of select="imp1:Lname"/>
          </imp1:Lname>
        </imp1:Employee>
      </xsl:for-each>
    </imp1:Root-Element>
</xsl:template>
</xsl:stylesheet>
Another option is to have a separate xsd with only one element (Fname or Lname) for the outbound file adapter, in which case you would need to map only one field.

JVM Error 547 - Flash Write Failed

Similar Messages

Maybe you are looking for