%C6K_PLATFORM-1-DISABLE_NON_C7600_CHASSIS

Dear Sir,
chassis is OSR-7609 with sup720, OSM-2+4GE-WAN+ and WS-X6548-RJ-45, we will add on SIP-400 with SPA-5X1GE-V2 into slot.
in order to support new hardware.
we try to upgrade from version s72033-advipservicesk9_wan-mz.122-18.SXF13.bin to c7600s72033-advipservicesk9-mz.122-33.SRB4.bin.
when reload new version, message as belows appear. system could not boot.
*Nov 17 18:12:14.355: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Nov 17 18:12:14.279: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
*Nov 17 18:12:14.319: %C6K_PLATFORM-1-DISABLE_NON_C7600_CHASSIS: Software has detected an attempt to run a c7600 image on an incompatible chassis OSR-7609 (36867). This image will not boot.
*Nov 17 18:12:14.739: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Nov 17 18:12:14.739: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
*Nov 17 18:12:14.739: %PFREDUN-4-SUP_FORCE_TO_ROMMON: Supervisor forced to rommon with reason: Cannot continue... disabling autoboot and resetting
System Bo otstrap, Version 8.1(3)
Copyright (c) 19 94-20 04 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory
rommon 1 >
due to the new version will check chassis type.
the original type is OSR-7609, please advise how to fix this issue in order to support SIP400 with SPA-5X1GE-V2 on OSR-7609.
looking forward to hearing from you soon.
thank you very much.
best regards,
Jason Lin

Your chassis is not supported in release 12.2SR
http://198.133.219.25/en/US/docs/routers/7600/Hardware/Hardware_Guides/Supervisor_Engine_and_Route_Switch_Processor_Guide/SupE02_ps368_TSD_Products_Installation_Guide_Chapter.html#wp1154003

Similar Messages

6509 - 720 Supervisor Module Failure after Password Recovery

Hi,
I attempted to perform a password recovery on a 6509 with dual WS-SUP720-3B modules running 12.2(33)SXI2A.
After changing the configuration register to 0x2142 and booting, I am getting a major error on the supervisor modules. I've changed the configuration register back to 0x2102 and am still getting the same error on both supervisor modules. I've also tried it with one module removed and one module installed.
I have about 30 seconds in where I can run commands before I get booted to rommon.
Any thoughts?
See below for the console output:
System Bootstrap, Version 8.5(3)
Copyright (c) 1994-2008 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 524288 Kbytes of main memory
Autoboot executing command: "boot bootdisk:"
Initializing ATA monitor library...
string is bootdisk:s72033-ipservicesk9-mz.122-33.SXI2a.bin
Loading image, please wait ...
Initializing ATA monitor library...
Self extracting the image... [OK]
Self decompressing the image : ################################################################################################################################################################################################### [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, s72033_sp Software (s72033_sp-IPSERVICESK9-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Sep-09 01:25 by prod_rel_team
Image text-base: 0x40101328, data-base: 0x4224F120
*Apr 19 05:03:02.747: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Apr 19 05:03:01.515: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor for this switch
Firmware compiled 19-May-09 12:08 by apyu Build [25600]
*Apr 19 05:03:02.747: %OIR-SP-6-CONSOLE: Changing console ownership to route processor
System Bootstrap, Version 12.2(17r)SX5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2006 by cisco Systems, Inc.
Cat6k-Sup720/RP platform with 524288 Kbytes of main memory
Download Start
Download Completed! Booting the image.
Self decompressing the image : ############################################################################################################################################################################################################################################################################################################################ [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Sep-09 01:00 by prod_rel_team
Image text-base: 0x40101328, data-base: 0x43A51E70
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco WS-C6509-E (R7000) processor (revision 1.5) with 458720K/65536K bytes of memory.
Processor board ID SMC133600GT
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
1 Virtual Ethernet interface
194 Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: no
Press RETURN to get started!
*Apr 19 04:55:51.335: RP: Currently running ROMMON from S (Gold) region
*Apr 19 04:55:52.107: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan. The Bridge IDs of all active STP instances have been updated, which might change the spanning tree topology
*Apr 19 04:56:00.531: %SYS-5-RESTART: System restarted --
Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c)
Router> 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Sep-09 01:00 by prod_rel_team
*Apr 19 05:03:03.111: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
*Apr 19 04:55:46.739: %SPANTREE-SP-5-EXTENDED_SYSID: Extended SysId enabled for type vlan. The Bridge IDs of all active STP instances have been updated, which might change the spanning tree topology
*Apr 19 04:55:46.747: SP: SP: Currently running ROMMON from S (Gold) region
*Apr 19 04:55:47.483: %SCHED-SP-7-WAen
Router#TCH: Attempt to set uninitialized watched boolean (address 0). -Process= "<interrupt level>", ipl= 1, pid= 3
-Traceback= 408E0820 40D74FEC 40D4B31C 40D4A1A8 40D46448 40F604B8 4173CCDC
*Apr 19 04:55:59.607: %SYS-SP-5-RESTART: System restarted --
Cisco IOS Software, s72033_sp Software (s72033_sp-IPSERVICESK9-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Sep-09 01:25 by prod_rel_team
Router#
Router#Apr 19 04:56:00.591: %OIR-SP-6-INSPS: Power supply inserted in slot 1
*Apr 19 04:56:00.695: %C6KPWR-SP-4-PSOK: power supply 1 turned on.
*Apr 19 04:56:00.943: %OIR-SP-6-INSPS: Power supply inserted in slot 2
Router#
Router#
Router#
*Apr 19 04:56:08.099: %FABRIC-SP-5-CLEAR_BLOCK: Clear block option is off for the fabric in slot 5.
*Apr 19 04:56:08.195: %FABRIC-SP-5-FABRIC_MODULE_ACTIVE: The Switch Fabric Module in slot 5 became active.
Router#
Router#
Router#
*Apr 19 04:56:09.567: %DIAG-SP-6-RUN_MINIMUM: Module 5: Running Minimal Diagnostics...
Router#
Router#
Router#
Router#show diagnostic result
% Incomplete command.
Router#show diagnostic result ?
module Module Keyword
Router#show diagnostic result ,modu modjle ule 5
Current bootup diagnostic level: minimal
Module 5: Supervisor Engine 720 (Active) SerialNo : SAL1338YTZ0
Overall Diagnostic Result for Module 5 : UNTESTED
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
1) TestScratchRegister -------------> U
2) TestSPRPInbandPing --------------> U
3) TestTransceiverIntegrity:
Port 1 2
U U
4) TestActiveToStandbyLoopback:
Port 1 2
--More-- U U
5) TestLoopback:
Port 1 2
6) TestNewIndexLearn ---------------> .
7) TestDontConditionalLearn --------> .
8) TestBadBpduTrap -----------------> .
9) TestMatchCapture ----------------> .
10) TestProtocolMatchChannel --------> .
11) TestFibDevices ------------------> F
12) TestIPv4FibShortcut -------------> F
13) TestL3Capture2 ------------------> F
14) TestIPv6FibShortcut -------------> F
15) TestMPLSFibShortcut -------------> F
16) TestNATFibShortcut --------------> F
17) TestAclPermit -------------------> F
18) TestAclDeny ---------------------> U
--More-- 19) TestQoSTcam ---------------------> U
20) TestL3VlanMet -------------------> U
21) TestIngressSpan -----------------> U
22) TestEgressSpan ------------------> U
23) TestNetflowInlineRewrite:
Port 1 2
U U
24) TestFabricSnakeForward ----------> U
25) TestFabricSnakeBackward ---------> U
26) TestTrafficStress ---------------> U
27) TestFibTcamSSRAM ----------------> U
28) TestAsicMemory ------------------> U
29) TestAclQosTcam ------------------> U
30) TestNetflowTcam -----------------> U
31) ScheduleSwitchover --------------> U
32) TestFirmwareDiagStatus ----------> U
33) TestAsicSync --------------------> U
34) TestUnusedPortLoopback:
--More--
Router#[Ashow diagnostic result module 5
Current bootup diagnostic level: minimal
Module 5: Supervisor Engine 720 (Active) SerialNo : SAL1338YTZ0
Overall Diagnostic Result for Module 5 : UNTESTED
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
1) TestScratchRegister -------------> U
2) TestSPRPInbandPing --------------> U
3) TestTransceiverIntegrity:
Port 1 2
U U
4) TestActiveToStandbyLoopback:
Port 1 2
--More--
Router#
*Apr 19 04:56:29.637: %DIAG-SP-3-MAJOR: M
%Software-forced reload
04:56:30 UTC Sun Apr 19 2015: Breakpoint exception, CPU signal 23, PC = 0x42735338
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
-Traceback= 42735338 42732E8C 423A6220 423A624C 421C1388 4223F614 4223F670 40962164 40963034 40962F54 40963D28 423259D0 42319604 42319820 42727FEC
$0 : 00000000, AT : 43FE0000, v0 : 45870000, v1 : 00000200
a0 : 46DC99C0, a1 : 44E05758, a2 : 00000000, a3 : 00000040
t0 : 00000010, t1 : 3400F101, t2 : 3400F100, t3 : FFFF00FF
t4 : 42728608, t5 : 00002F04, t6 : 80000000, t7 : 00000000
s0 : 00000000, s1 : 43EE0000, s2 : 50449158, s3 : 0000001F
s4 : 50449158, s5 : 470B3AB4, s6 : 00000000, s7 : 08A5DFC8
t8 : 08028FEC, t9 : 00000000, k0 : 00000000, k1 : 00000000
gp : 43FDDE8C, sp : 5000DBB0, s8 : 00000000, ra : 42732E8C
EPC : 42735338, ErrorEPC : 870FDDF0, SREG : 3400F103
MDLO : 00000000, MDHI : 00000000, BadVaddr : 00000000
DATA_START : 0x43A51E70
Cause 00000824 (Code 0x9): Breakpoint exception
Writing crashinfo to bootflash:crashinfo_20150419-045630
=== Flushing messages (04:56:30 UTC Sun Apr 19 2015) ===
Buffered messages:
*Apr 19 04:55:51.335: RP: Currently running ROMMON from S (Gold) region
*Apr 19 04:55:52.107: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan. The Bridge IDs of all active STP instances have been updated, which might change the spanning tree topology
*Apr 19 04:56:00.531: %SYS-5-RESTART: System restarted --
Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Sep-09 01:00 by prod_rel_team
*Apr 19 05:03:03.111: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
*Apr 19 04:55:46.739: %SPANTREE-SP-5-EXTENDED_SYSID: Extended SysId enabled for type vlan. The Bridge IDs of all active STP instances have been updated, which might change the spanning tree topology
*Apr 19 04:55:46.747: SP: SP: Currently running ROMMON from S (Gold) region
*Apr 19 04:55:47.483: %SCHED-SP-7-WATCH: Attempt to set uninitialized watched boolean (address 0). -Process= "<interrupt level>", ipl= 1, pid= 3
-Traceback= 408E0820 40D74FEC 40D4B31C 40D4A1A8 40D46448 40F604B8 4173CCDC
*Apr 19 04:55:59.607: %SYS-SP-5-RESTART: System restarted --
Cisco IOS Software, s72033_sp Software (s72033_sp-IPSERVICESK9-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Sep-09 01:25 by prod_rel_team
*Apr 19 04:56:00.591: %OIR-SP-6-INSPS: Power supply inserted in slot 1
*Apr 19 04:56:00.695: %C6KPWR-SP-4-PSOK: power supply 1 turned on.
*Apr 19 04:56:00.943: %OIR-SP-6-INSPS: Power supply inserted in slot 2
*Apr 19 04:56:08.099: %FABRIC-SP-5-CLEAR_BLOCK: Clear block option is off for the fabric in slot 5.
*Apr 19 04:56:08.195: %FABRIC-SP-5-FABRIC_MODULE_ACTIVE: The Switch Fabric Module in slot 5 became active.
*Apr 19 04:56:09.567: %DIAG-SP-6-RUN_MINIMUM: Module 5: Running Minimal Diagnostics...
*Apr 19 04:56:29.637: %DIAG-SP-3-MAJOR: Module 5: Online Diagnostics detected a Major Error. Please use 'show diagnostic result <target>' to see test results.
*Apr 19 04:56:29.641: %CONST_DIAG-SP-3-BOOTUP_TEST_FAIL: Module 5: TestFibDevices failed
*Apr 19 04:56:29.641: %CONST_DIAG-SP-3-BOOTUP_TEST_FAIL: Module 5: TestIPv4FibShortcut failed
*Apr 19 04:56:29.641: %CONST_DIAG-SP-3-BOOTUP_TEST_FAIL: Module 5: TestL3Capture2 failed
*Apr 19 04:56:29.641: %CONST_DIAG-SP-3-BOOTUP_TEST_FAIL: Module 5: TestIPv6FibShortcut failed
*Apr 19 04:56:29.641: %CONST_DIAG-SP-3-BOOTUP_TEST_FAIL: Module 5: TestMPLSFibShortcut failed
*Apr 19 04:56:29.641: %CONST_DIAG-SP-3-BOOTUP_TEST_FAIL: Module 5: TestNATFibShortcut failed
Queued messages:
*Apr 19 04:56:33.583: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
IPv6FibShortcut failed
*Apr 19 04:56:29.641: %CONST_DIAG-SP-3-BOOTUP_TEST_FAIL: Module 5: TestMPLSFibShortcut failed
*Apr 19 04:56:29.641: %CONST_DIAG-SP-3-BOOTUP_TEST_FAIL: Module 5: TestNATFibShortcut failed
*Apr 19 04:56:29.971: %HA_EM-6-LOG: Mandatory.go_bootup.tcl: GOLD EEM TCL policy for boot up diagnostic
*Apr 19 04:56:30.575: %CPU_MONITOR-3-PEER_EXCEPTION: CPU_MONITOR peer has failed due to exception , reset by [5/0]
*** System received a Software forced crash ***
signal= 0x17, code= 0x24, context= 0x45876f54
PC = 0x42728664, SP = 0x43ed9cd8, RA = 0x413ad2f4
Cause Reg = 0x00003820, Status Reg = 0x34008002
rommon 1 >

What kind of line card was being inserted in slot 6? Have you tried other slots? The crash file in the RP says it was reset by SP, so the important crashinfo file would be in the sup-bootflash: Try an see if you find any "dir sup-bootflash:"
Aug 5 17:46:11: %C6K_PLATFORM-2-PEER_RESET: RP is being reset by the SP
%Software-forced reload
To answer your question:
A Is there any different procedure to install line modules in supervisor slots?
>>No there are no special configuration you need to do when inserting a line card in slots that normally would be for supervisor.
B Switch is having previously removed linecard (i.e, fastethernet module)in running configuration. Will it create any system crash?
>>No, it will not cause the switch to crash, when you see the configuration of a line card even after it was removed is quite normal, it's cold module provisionsing, you would not want to keep putting in a configuration for any line card after just resetaing them do you?

IDSM-2 Hot-swapable?

Hi Guys,
I need some information!
Is the IDSM2 hot-swappable in a Cisco 6509 Chassis?
Recently I installed the IDSM2 on an Cisco 6509 Chassis (with two Sup720s in SSO mode). But chassis rebooted specifying that the
"%C6K_PLATFORM-2-PEER_RESET: RP is being reset by the SP"
After rebooting the secondary SUP became active.
Can anyone give an explaination for this?
Also Please do let me know whether the IDSM is hot-swappable or not?
Prompt response will be appreciated.
Thanks
Anand

If that the case, maybe it could be other things, even to the extend of bugs.
As you're saying, the blade is properly shutdown and removed from the slot. This make the active SupEngine to go down, and standby takes over.
With fresh idsm2 (not configured), this shouldn't happened. From my experience, I can always remove and put back the module without any issues with SupEngine.
BTW, IDSM2 is confirmed hot-swap, and shouldn't caused any issue to the switch
http://www.cisco.com/en/US/products/hw/modules/ps2706/products_data_sheet09186a00801e55dd.html
Rgds,
AK

Crash inserting module

Hallo,
I've problems inserting objetcs (modules) in Acrobat.
If I insert a module in a PDF with Adobe Acrobat 7 Professional I haven't problems.
If I do the same thing with Adobe Acrobat X Professional the program hangs.
If I do the same thing with Adobe Acrobat 9 Professional the program hangs.
The problem isn't present with all PDFs, but only with files PDFs that are conversions of DWGs drawings.
The programs Adobe Acrobat used have all disposable updates installed.
Could you help me, please?
Thank you very much.
Yuri Ceroni

What kind of line card was being inserted in slot 6? Have you tried other slots? The crash file in the RP says it was reset by SP, so the important crashinfo file would be in the sup-bootflash: Try an see if you find any "dir sup-bootflash:"
Aug 5 17:46:11: %C6K_PLATFORM-2-PEER_RESET: RP is being reset by the SP
%Software-forced reload
To answer your question:
A Is there any different procedure to install line modules in supervisor slots?
>>No there are no special configuration you need to do when inserting a line card in slots that normally would be for supervisor.
B Switch is having previously removed linecard (i.e, fastethernet module)in running configuration. Will it create any system crash?
>>No, it will not cause the switch to crash, when you see the configuration of a line card even after it was removed is quite normal, it's cold module provisionsing, you would not want to keep putting in a configuration for any line card after just resetaing them do you?

%C6K_PLATFORM-1-DISABLE_NON_C7600_CHASSIS

Similar Messages

Maybe you are looking for