K1 and N-trig digitizer pen

Does anyone know whether a N-trig pen would work on the K1? Would this tablet support pressure sensitive inputs?
Thx

usualy this message means there is no communication between the digitizer and the computer.
the only thing you can do is contact Dell/HP support and they will probably reflash or replace your screen.

Similar Messages

Problems with Illustrator CC 2014 in Sony Vaio Fit 15A with N-Trig touch screen and digitizer pen.

Hello to everybody!
Some times ago Adobe has updated Illustrator to CC 2014 version and now it support touch pressure\pan\zoom in Windows 8 tablets. I have Sony Vaio Fit 15A with N-Trig touch screen and digitizer pen with pressure-sensitive support.
I was extremely disappointed that the brush in new version does not work correctly. Watch the video please that I did specifically for the demonstration.
I use Adobe Illustrator CS6 and Adobe Illustrator CC 2014 for comparison. In the old version the brush is works correctly. You must do a lot of clicks to start the brush in CC 2014 version (please see video). What causes of the problem? Please help me!

Hello to everybody!
Some times ago Adobe has updated Illustrator to CC 2014 version and now it support touch pressure\pan\zoom in Windows 8 tablets. I have Sony Vaio Fit 15A with N-Trig touch screen and digitizer pen with pressure-sensitive support.
I was extremely disappointed that the brush in new version does not work correctly. Watch the video please that I did specifically for the demonstration.
I use Adobe Illustrator CS6 and Adobe Illustrator CC 2014 for comparison. In the old version the brush is works correctly. You must do a lot of clicks to start the brush in CC 2014 version (please see video). What causes of the problem? Please help me!

ThinkPad Tablet 10 (TPT10) digitizer pen does not work

I have a new TPT10 that came with the ultra keyboard and digitizer pen. Pen is completely unresponsive, touch screen works fine. TPT10 is fully updated with both Msoft and Lenovo software/drivers.

did you ever get this resolved? I have the same problem.

Digitizer pen

I have just recently bought an i7 Lenovo Yoga pro 2. As many of you may know, it does not come with a digitizer pen. I would like to purchase one but I am not sure what to get. Please help me with suggestions.

Good afternoon and welcome to the community.
The Yoga 2 Pro doesn't have a digitizer. The panel is 10-finger capacitive touch. That said, there are a number of capacitive stylii available, but I don't have experience with them , so I can't offer a recommendation.
Hopefully other members will join the discussion with their experiences that will aid your decision.
Cheers.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
PM requests for individual support are not answered. If a post solves your issue, please mark it so.
X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
I am not a Lenovo employee.

Will the Lenovo Helix Digitizer Pen work with Windows 7

Hello forum,
I work in the IT department and we have recently order a number of Lenovo Helix to use for special projects.
We will be downgrading to Windows 7 64-bit.
My question is will the digitizer pen still be supported by Windows 7?
Maybe I over looked, but I did not see any drivers that seemed to be associated with the digitizer pen or any previous mention of this and downgrading to Windows 7.
Any information you can provide will be helpful.
Solved!
Go to Solution.

Welcome to the forum!
Stylus pen is natively supported by W7 and it will work "out of the box".
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Best Replacement digitizer pen for my TouchSmart Tm2

Hi, I recently lost my digitizer pen to my touchsmart tm2 notebook, I looked for an exact replacement to this pen but they seem to be out of stock. Are there other digitizer pens that work with my notebook you can recomend?
I don't mind buying another brand or another type of pen from HP so as long as it works with my notebook.
Plus I don't want to draw with my mouse ( Btw I am an illustrator)

@jcarmona1978
‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
If you are unfamiliar with the Forum's private messaging please click here to learn more.
Thank you,
Omar
I Work for HP

Split x2 with digitizer pen

I have a spare digitizer pen I got when I purchased my TM2 Touchsmart. Is there a way to have this, or any other Wacom pen, work with the Split x2. I've tried the TM2 driver and the Wacom driver without success. Has anyone else tried this too?

Hi plloyd1010,
In my knowledge, the Split X2 will not work with Digitizer pens of any kind.
!------------------- Please click the KUDOS star on the left to say 'Thanks'. Please mark 'Accept as Solution' if it answers/solves your problem. Thank you-----------------------------------------------------------------!
I am an HP Employee.

What digitizer pen is compatible with Portege Z10T-A

Hi All,
I have the z10t-a i5 telstra 4G cellular model.
This model did not come with the digitizer pen or stylus and i am wondering if the pens are compatible.
The support website says the pen is compatible with the Z series but am not sure.
Can anyone shed any light on the subject.
I would hate to spend the money on an accessory that did not work.
Cheers

Hi guys,
I found also some details about the Toshiba Digitizer Pen with Eraser
Part number: PA5133U-1EUC and this digitizer pen is compatible with the Toshiba Portg Z10t, Z15t Ultrabook series and 10 Excite Write Tablet PC
Further details:
+Using this digitizer pen, you can write directly on the screen and save your notes in your own handwriting - or convert them to typed text for use in other applications. The pen can also handle common mouse and keyboard tasks like opening applications, selecting text and displaying menus. Since the grid provides the power to the pen through resonant coupling, no batteries are required. Keep a spare pen handy.+

Yoga S1 Digitizer Pen Question

I just got a Yoga S1 with the Digitizer Pen. Is the pen supposed to behave similar to a standard touch? In otherwords, can I use it instead of my finger when touching the screen? So far it doesn't seem to have any affect on the windows start screen. I know the pen works because I found an app that translates the writing to text (can't remember the app name, still learning what came on the computer). I'm just trying to learn the capabilities and limitations of the pen.
Thanks in advance
Solved!
Go to Solution.

https://www.flickr.com/photos/lead_org/14487189987/
i recorded the above video to show you the basic behaviour under both finger touch and pen digitiser. Compare this to your laptop, and see if it is the same.
Also, it would helpful to do a video recording of what you are getting, then upload it to say flickr or something. This will allow us to troubleshoot more easily.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

How do I turn off the alt scroll zoom? When I'm in Adobe photoshop and illustrator using the pen tool, alt is utilized for another short cut. I would like to use the alt command for the pen tool instead of zooming into the screen.

How do I turn off the alt scroll zoom?
When I'm in Adobe photoshop and illustrator using the pen tool, alt is utilized for another short cut. I would like to use the alt command for the pen tool instead of zooming into the screen.

I tend to select things from left to right and every time I am moving in a downward right diagonal motion during lasso selection I am missing a clear view and I am tending to have a more sloppy selection. All this does is slow me down since I need to go back and hit those areas again. The big arrowhead just get's in the way. The original lasso tool with the thin line and small active point at it's lower left was far better for me.
I don't like turning the cursors to precise because I like to see the active tool icon where my cursor is and as the icon changes as I hold modifier keys down. If I am forced to get comfortable with using pricise cursors I guess I will, but man, I've never had to do this in my 15 years of photoshop use...
I would absolutely LOVE to find a way to get the old lasso icon -- without the arrowhead above it.
Is there any chance this option could be inlcuded in cursor preferences? I'd give much thanks, Adobe.

Layers feature and a layer mask pen tool

Could we see a simple Layers feature and a layer mask pen tool - so that we don't have to go to photoshop for simple cutout etc.

Theres some basic stuff you are not understanding…
1. In Photoshop there is the pen tool for creating abstract vector edges, and selection tools (lasso, magic wand etc). You need to turn the results of the pen tool into a selection. Best way is using the the Command/return shortcut, or command clicking on the path in the paths panel.
2 layers need to be , not - If you want to delete areas (make them transparent). To do this either go to Layer/New/Layer from background - or hold Option and double click the Background layer.
3 See answer 2, and use Free Transform (command T)

Is the new slider2 support digitizer pen?

Is the new convertible tablet slider2 support digitizer pen?

The new earpods should support extended bass noise with other devices as it is not a software eq but the actual physical response of the speaker inside the earpod.
Hope it helps
Ryan

Hello,Where in Singapore can I get a LCD display and touch screen digitizer for a iphone 2g.

Hi there,Where in Singapore can I get a LCD display and touch screen digitizer for a iphone 2g.

Try searching google.

Synchronisation of M Series and High Speed Digitizer

Hello everybody,
i just have a question regarding synchronisation/timing of two different PCI cards (M-Series PCI 6220 and High Speed Digitizer PCI 5112, connected via RTSI cable).
I wonder how I can synchronise signals, because those cards use different mechanisms in Labview for timing and synchronisation.
Can anybody tell me, how I can synchronise the clocksignals and let them use the same trigger (actually I want to use the external trigger of the 5112)? Witch VIs do I have to use?
Thanks in advance
Oliver

Hello!
First of all many thanks for your reply.
Exporting the external trigger from the 5112 to 6220 via RTSI works.
Synchronising the clocks in the same way as you wrote doesn't seem to work. May be I did something wrong.
What I did was the following:
I exported the "reference clock" signal of the PCI 5112 using "niScope export signal.vi" to RTSI 7.
Than I used the daqmx "sample clock.vi" to configure the
clock. I used the instance "sample clock" with "dev1/RTSI 7" as
the source (dev 1 actually is PCI 6220) and as sample mode "continous
samples". I started the PCI 6220 (daqmx) first, after that I started
the 5112 (niScope).
Running this vi I get the following error:
"ADC conversion attempted before the prior conversion was complete.
Increase the period between ADC conversions. If you are using an
external clock, check your signal for the presence of noise or
glitches."
This is still a small problem, but meanwhile I came to a bigger one:
I thought I could use the 6220 in the same way I can use the 5112:
I want to fetch (or read) data on both cards contionously but also
periodically. The period time is given by the External trigger I
mentionend before. Till now I didn't find a way to aquire the data from
the 6220 in records of a given length (let's say 100 samples, at 1kHz)
every time the trigger occurs (External Trigger rate is about 250 Hz).
This is possible with the 5112 board, but I wonder if this is also
possible with the 6220?
Kind regards
Oliver
PS: Sorry for the "witch"

How to fill up pdf forms & sign pdf contracts using digitizer pen & tablet?

Greetings,
I travel a lot and bring tons of documents for clients to sign. As I am trying to cut down on travel weight, i fancied upon the idea of using a digitizer such as the Genius EasyPen i405 to fill up pdf forms and sign contracts so i wouldnt have to scan, save and email the forms back to the office thousands of miles away. I would like to know if it is possble to do that using such a device. If its possible, how? I use acrobat X. Any advise you can give would be greatly appreciated. Hope to hear from you soonest. Thank you.

Thanks for your response jallisy. I just thought about this because i read somewhere that the pen acts like a mouse cursor when you move it around the digitizer. I figured the pen could act as a mouse while the digitizer could act as a mouse pad, as such the size doesnt really matter, considering you need to press a button on the pen to engage the digital ink and you use the computer screen as your guide. I havent really tried one but am just starting to explore the idea as tablets like the Ipad are now allowing users to fill up forms and sign pdfs with a finger or a capacitive pen. Youtube offers all these interesting pdf signing and editing with the Ipad. I just really dont want an Ipad. I still think a solution is just around the corner. But i am not willing to buy an expensive tablet with limited storage and productivity features over a real laptop.
The genius site for the pen stated that i can sign microsof office docs but no pdf was mentioned. I guess they have a special software for that but the people at genius havent gotten back to me yet. Another way i was thinking about was converting all the pdfs to word, sign the word document and then save as a pdf again ... the document is prone to be edited though and formats could be accidentally changed so was really thinking about doing this directly with a PDF instead.

K1 and N-trig digitizer pen

Similar Messages

Maybe you are looking for