K3B unable to write dvd-r after 0.12.10-1 - 0.12.11-1

As the subject says, after upgrading to the 0.12.11-1 version of k3b, there is a "mmap" error, unable to anonymously allocate error.
I tried the ulimit thing, but it didn't work.
Reverting to the 0.12.10-1 version avoids the error.
Edit: The exact error is :-( unable to anonymously mmap 67108864: Resource temporarily unavailable
It burns CD ok still.

Haiyadragon wrote:Give the following parameters to growisofs (in k3b settings): "-use-the-force-luke=bufsize:16m".
not work 

Similar Messages

  • Unable to write DVDs w/T61p Multi-Recorder (Optiarc AD-7910A)

    I have a pack of Memorex DVD-R 16X DVDs which I tries to use to write recovery DVDs with.  Both the Vista back up program and the ThinkVantage Rescue/Recover program faild to write to DVDs.  Ended up writing 8 CDs instead.
    Has anyone else had a problem writing DVDs with theit T61p?

    Optiarc AD-7910A Product Specification
    Transfer Rate Read: 
    DVD-ROM 8x (max. 11,000 kByte/s) CD-ROM 24x (max. 3,600 kByte/s) 
    Transfer Rate Write: 
    DVD-R: 8x (max. 11,000 kByte/s) DVD-RW: 6x (max. 8,250 kByte/s) DVD-R DL: 4x (max. 5,500 kByte/s) DVD-RAM: 5x (max. 6,900 kByte/s) DVD+R: 8x (max. 11,000 kByte/s) DVD+RW: 8x (max. 11,000 kByte/s) DVD+R DL: 4x (max. 5,500 kByte/s) CD-R: 24x (max. 3,600 kByte/s) CD-RW: 16x (max. 2,400 kByte/s) 
    Access time: 
    DVD: 180 ms CD: 150 ms 
    Mechanism: 
    Internal 12/8 cm CD- and DVD-drive (half height form factor), tray load mechanism for horizontal and vertical use, emergency eject 
    Interface: 
    IDE/ATAPI 
    Burst Transfer Rate: 
    PIO mode 4/Ultra DMA 33 (max. 33 MByte/s transfer rate) 
    Cache Memory: 
    2 MByte 
    Media/Modes Supported: 
    DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD-RAM, DVD +R, DVD +R DL, DVD +RW, DVD-Video, CD-ROM, CD-ROM XA, CDAudio, CD-Extra, CD-Text, CD-I Ready, CD-Bridge, Photo-CD, Video-CD, Hybrid-CD 
    Writing Methods: 
    DAO (disc at once), SAO (session at once), TAO (track at once) with zero gap, variable or fixed packet, multisession 
    Compatibility: 
    MPC Level 3, MultiRead, PC2001 
    Weight: 
    0.15 kg 
    Dimensions: 
    9.5 mm x 128 mm x 129 mm 
    I don't work for Lenovo

  • I'm unable to write/burn a CD-R (Verbatim) from a playlist after upgrading to iTunes 12.0.1.26. I get error 4000. I can however write/burn a CD from Windows Explorer and CDBurnerXP v4.5.4.5143 – which implies the device is working OK

    I’m unable to write/burn a CD-R (Verbatim) from a playlist after upgrading to iTunes 12.0.1.26. I get error 4000. I can however write/burn a CD from Windows Explorer and CDBurnerXP v4.5.4.5143 – which implies the device is working OK – and only fails when I write from iTunes.  The drivers are up to date
    Microsoft Windows 7 x64 Business Edition Service Pack 1 (Build 7601)
    Dell Inc. Latitude E6420
    iTunes 12.0.1.26
    QuickTime 7.7.6
    FairPlay 2.7.39
    Apple Application Support 3.1
    iPod Updater Library 12.0
    CD Driver 2.2.3.0
    CD Driver DLL 2.1.3.1
    Apple Mobile Device 8.0.5.6
    Apple Mobile Device Driver 1.65.0.0
    Bonjour 3.0.0.10 (333.10)
    Gracenote SDK 3.06.0.2770
    Gracenote MusicID 3.06.0.2770
    Gracenote Submit 3.06.0.2770
    Gracenote DSP 3.06.0.2770
    iTunes Serial Number 756D13C00C3583C8
    Current user is not an administrator.
    The current local date and time is 2015-01-13 14:47:35.
    iTunes is not running in safe mode.
    WebKit accelerated compositing is enabled.
    HDCP is supported.
    Core Media is supported.
    Video Display Information
    Intel Corporation, Intel(R) HD Graphics Family
    **** External Plug-ins Information ****
    No external plug-ins installed.
    iPodService 12.0.1.26 (x64) is currently running.
    iTunesHelper 12.0.1.26 is currently running.
    Apple Mobile Device service 3.3.0.0 is currently running.
    **** CD/DVD Drive Tests ****
    LowerFilters: SbCeCd (3.2.6.3),
    UpperFilters: GEARAspiWDM (2.2.3.0),
    F: HL-DT-ST DVD+-RW GU40N, Rev A103
    Drive is empty.
    The last failed audio CD burn had error code 4000(0x00000fa0). It happened on drive F: HL-DT-ST DVD+-RW GU40N on CDR media at speed 24X.
    F: HL-DT-ST DVD+-RW GU40N, Rev A103
    Audio CD in drive.
    Failed Reading table of contents, error 4000.
    Check the website of your computer or drive manufacturer to verify that you have the latest firmware for your CD / DVD drive.
    Audio CD reading failed. Error Code:   87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87.
    iTunes cannot play or import music from a CD in this drive. The drive may need a firmware update. Check with the manufacturer.
    Get drive speed failed. Error Code: 4000.
    The last failed audio CD burn had error code 4000(0x00000fa0). It happened on drive F: HL-DT-ST DVD+-RW GU40N on CDR media at speed 24X.

    Hi iTunes-1,
    Welcome to the Support Communities!  The error message you posted indicates a possible firmware update is needed for iTunes for Windows to work with your CD drive.  
    iTunes for Windows: Updating the firmware on your CD or DVD drive - Apple Support
    http://support.apple.com/en-us/HT201852
    Having outdated firmware can cause issues using CDs and DVDs with iTunes for Windows. Firmware is a type of software stored in a chip in hardware that can sometimes be updated.Identifying drives and firmware versions
    To run CD Diagnostics, follow the steps in this document.
    After following the steps to run CD Diagnostics linked above, look at section three to find out more about your optical drive(s).
    Here is an example of what section three might look like:
    In this example there are two drives. Drive E is a Samsung DVD-ROM drive with a model designation of SD-616 that has firmware version F000. Drive F is an NEC drive with a model designation of NR-7900A that has firmware version 1.08.Updating the firmware
    If the optical drive you are using came with your computer, check with the support site for your computer for a firmware update. Typically you will need to go to the support website for the computer maker and click on a "downloads" or "updates" link, and then enter your computer model designation and operating system version to see what updates are available. Then look through the available updates for a firmware update for your optical drive. Download the updater and run it. If you need assistance applying the update, contact the maker of your computer.
    If the optical drive you are using came as a separate part (was not included with a computer), check the support site for the drive maker for a firmware update. Sometimes the manufacturer is not clear in the CD Diagnostics results. In that case, you may just have to search the Internet for the drive model designation. You can usually find out who made the drive by looking through the results of such a search. Once you have identified who made your drive, go to the support website for that company. Look for a "downloads" or "updates" link, and then enter your optical drive model designation. Download the updater and run it. If you need assistance applying the update, contact the maker of the optical drive.Verifying that the firmware was updated
    Run CD Diagnostics again.
    Examine the CD Diagnostics results. The firmware version for the drive should be the new version.
    Information about products not manufactured by Apple, or independent websites not controlled or tested by Apple, is provided without recommendation or endorsement. Apple assumes no responsibility with regard to the selection, performance, or use of third-party websites or products. Apple makes no representations regarding third-party website accuracy or reliability. Risks are inherent in the use of the Internet. Contact the vendor for additional information.
    Last Modified: Nov 8, 2014
    Also, you mentioned that you have been successful burning a CD with the Windows OS.  Make sure that you have closed all software programs that can access the CD burner so that there isn't a conflict for the drive.   Sometimes chaning the burn speed from "maximum" to 8x can also help in this situation.
    I hope this information helps ...
    - Judy

  • Unable to write to external drive after drive sleeps

    This topic seems to be all over the place. I want to know if there is a fix.
    I have a number of external disk drives. They are connected via USB and firewire. About 30% of the time, if a drive has been put in sleep mode and then later awakened, I am unable to write to it. If I try to dismount the drive I get a -50 error that the drive is in use. But that is not true because nothing but the finder is running. If I look the console log there are lots of the following messages.
    Dec 6 15:50:43 squid fseventsd[45]: disk logger: failed to open output file /Volumes/Calvary1TB/.fseventsd/63657332a56b8d30 (Invalid argument). mount point /Volumes/Calvary1TB/.fseventsd
    Dec 6 15:50:50 squid UnmountAssistant[1463]:
    The drive in question is the CAXM Calvary1TB drive. BTW when I received the Calvary disk drive, I reformatted it OSX journaled with a GUID partition before using it. All my other 8 TB of storage is formatted the same way and I had no problems before Snow Leopard. Anyhow, If I force a dismount, all returns to normal. OR if I disable sleep the drive drives options in the energy saver preferences, the problem disappears. But then none of the drives ever spin down.
    Once every 50 or so forced dismounts (it happens a lot), OSX will crash with the kiss of death display.
    This problem did not exist in pre Snow Leopard, so obviously changes were made to the file system and not properly tested. Anyone have any idea when this will be fixed.

    The drive in question is the CAXM Calvary1TB drive.
    Calvary lists this drive series only in its "Windows PC" section at http://www.cavalrystorage.com/pr_index.htm. This could be a problem because different manufacturers use different methods to implement wake-from-sleep (or more generally, energy management features) in the support circuitry of external drives. IOW, there are no universal standards for this, so manufacturers may or may not design their implementations for cross-platform compatibility.
    Unfortunately, since Windows PC's dominate the market some manufacturers use energy management methods in some or all of their designs that work reliably only with that platform. For this reason, there is always some risk of unexpected behavior when using external drives not specifically marketed as Mac OS X compatible with a Mac. (This is not a problem with "raw" internal drives directly connected to a Mac's SATA interface because there is no support circuitry involved.)
    Since you already have invested in these drives, your best bet is to contact Calvary & see if they can offer a solution. If you are lucky, they may have a firmware updater for the CAXM series that works reliably with Snow Leopard; if not, they may simply tell you not to let the drives sleep, or that they don't support the CAXM series with Macs & you are on your own.

  • RW-00000: Unable to write the following directory after aborting rapidwiz

    Hello installation Gurus,
    I am running rapidwiz as root to install/upgrade ebs to 12.1.1 on oracle Linux 6 and it is failing on the database Node Configuration with
    "RW-00000: Unable to write the following directory. Please check permissions." The irony is it doesn't exactly tells me which directory.
    My oracle account is orafint and owns /u01/app/oracle and /u01/app/oracle/product/11.1.0/db_1.
    I rant through this installation last night and abort at when I realised that it could not continue for lack of an existing inventory as I had yet installed the database rdmbs. I cancelled rapidwiz, installed the rdbms, created a database and rebooted the server. I have tried "rapidwiz -restart" to no avail.
    The log file /tmp/11021532 has not errors in it. No file in oraInventory/ has been updated since I started this installation.
    I have read a few forums but non was of help.
    Thanks
    Mathias

    Hi Hussein,
    thanks, Note [ID 110372.1] solved that problem by renaming /etc/oraInst.loc, some files in/tmp and then restarting the installation.
    But I just encountered another problem towards the end of my installation:
    RW-50016: Error: - Database ORACLE_HOME environment file was not created:
    File = /u01/app/oracle/product/11.1.0/db_1/OFTEST_ofintest.env
    RW-50016: Error: - TNSNames SQL*Net file was not created:
    File = /u01/app/oracle/product/11.1.0/db_1/network/admin/OFTEST_ofintest/tnsnames.ora
    RW-50016: Error: - APPL_TOP environment file was not created:
    File = /u02/applfint/apps/apps_st/appl/OFTEST_ofintest.env
    RW-50016: Error: - ADOVARS environment file was not created:
    File = /u02/applfint/apps/apps_st/appl/admin/adovars.env
    RW-50016: Error: - APPSCONFIG was not created:
    File = /u02/applfint/apps/apps_st/appl/admin/adconfig.txt
    I had precious successfully installed from this same directory about two twice within the past two months for testing so rapid install is up to date.
    Thanks
    Mathias

  • Can't upgrade iPhoto Library - 'unable to write to library "iPhoto Library"'

    I apologise in advance if this is a little convoluted.
    I have a MacBook Pro purchased a little over a year ago and I'm not sure what version of iPhoto is was running. It had a meltdown when I tried to upgrade to Mountain Lion and was ably serviced and returned to me with all my data heroically saved and stored in a shared folder.
    When I got it back I upgraded successfully to Mountain Lion and installed all the iPhoto updates. After a false start, and having to reinstall iPhoto I am now running 9.4.3.
    I have shifted my old iPhoto Library out of the shared folder and into the Pictures folder where it sits alongside the pretty much empty iPhoto Library created automatically by the install. When I try to open my old Library it says it needs to be upgraded, which makes sense, but immediately after the upgrade commences I get an error message saying 'Unable to write to library "iPhoto Library" Check that you have permission to write to the library directory'. I am not sure what to do from this point.
    I have verified that the photos are all still in the old iPhoto Library Package.
    Thank you.
    Melanie

    Hang on - I had browsed extensively, but it was only after I wrote my question that all the other similar ones popped up on the side bar. I've followed the advice in some of those and it seems to be working. I apologise, but I seem to be unable to delete this discussion.

  • [Solved] CUPS: Unable to write print data: Input/output error

    I'm filling this for the benefit of those poor googlers that can reach here.
    Symptoms: After trying to print a "complex" image the printer made too much breaks, and failed.
    The problem is, it then didn't came up. I mean, I restarted the printer, cupsd, the whole system, and nothing.
    I was unable to print again, it showed "Unable to write print data: Input/output error" and refused to print anything.
    I then saw that in /etc/cups I had printers.conf and printers.conf.O files, which differed (other than in StateTime), that printers.conf.O had
    State Idle
    but printers.conf had:
    State Stopped
    StateMessage Unable to write print data: Input/output error
    Reason paused
    Probably due to the ErrorPolicy being stop-printer.
    So seeing I followed the following steps:
    Stop cups
    Replace printers.conf with printers.conf.O (I could also had manually edited it)
    Start cups
    It then went working flawlessly.
    There was probably an option in the web interface combobox for doing that. The problem is that I didn't realise it was stopped, so didn't know how to make it work. Moreover, some posts in the web recommended reinstalling the printer (which would skip the problem by creating a new printer).

    I think that I had this same problem, and fixed it by reinstalling the printer.  Thank you for your post.

  • File manager unable to write data on USB/mem card

    After updated to Android 4.4, I am unable to write data on USB pendrive or on memory card( only inbuilt app - File commander can write data on memory card but not on USB pen drive).
    With file commander, I can read SD card and Micro USB pen drive( which means I can copy data from SD card and Micro USB pen drive to phone memory).
    But with File commander, I can write data on SD card( which means I can create folders and copy data to SD card) but not on Micro USB Pen drive.
    If any body has solution to that write restriction on micro USB pen drive, please tell ????????
    Upto Android 4.3 I can write on SD card and micro USB pen drive with any file manager app.
    But with 4.4, I can write only on SD card with only In build file commander app, but not on micro USB pen drive.
    Solved!
    Go to Solution.

    http://talk.sonymobile.com/t5/Xperia-Z-Ultra/What-changed-in-Android-4-4-KitKat-with-SD-cards/m-p/63...
    "I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

  • Have downloaded i Tunes 10.5.1.42 but get an error message on installation saying unable to write to CFNetwork.dll. This file is present in Program Files\Common Files\Apple\Apple Application Support which is where it should be....any ideas??

    Have downloaded i Tunes 10.5.1.42 but get an error message on installation saying unable to write to CFNetwork.dll. This file is present in Program Files\Common Files\Apple\Apple Application Support which is where it should be....any ideas??
    Is a copy of the CFNetwork file available for download if mine is corrupted?
    Thanks

    get an error message on installation saying unable to write to CFNetwork.dll. This file is present in Program Files\Common Files\Apple\Apple Application Support which is where it should be....any ideas??
    That one's consistent with disk/file damage. The first thing I'd try with that is running a disk check (chkdsk) over your C drive.
    XP instructions in the following document: How to perform disk error checking in Windows XP
    Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
    Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards?

  • MAC HANGS WHEN I WRITE DVD VIDEO USING TOAST OR IDVD

    DEAR SIR,
    I HAVE A PROBLEM WITH MY SONY DVD .. EVERY TIME I TRY TO WRITE DVD VIDEO MY MAC HANGS WHEN TOAST ROXIO 10 STARTS TO LEAD OUT AFTER ENCODING THE VIDEO .. AND IT HANGS ALSO WITH IDVD AFTER ENCODING THE VIDEO .. AND I MUST RESTART MY MAC ...PLEASE TELL ME HOW TO FIX IT ??
    Model: SONY DVD RW DRU-835A
    Revision: SS02
    Removable Media: Yes
    Detachable Drive: No
    BSD Name: disk2
    Protocol: ATAPI
    Unit Number: 1
    Socket Type: Internal
    Low Power Polling: No
    Mac OS 9 Drivers: No
    Partition Map Type: Unknown
    S.M.A.R.T. status: Not Supported
    THANK YOU FOR YOUR TIME
    TAHA TALAAT
    [email protected]

    This is a user forum.
    Caps is considered yelling, inappropriate, a left over from DOS, too. Oh, and it actually is HARDer to read.

  • Error Log entry Unable to write file with XML Saver

    Hi all,
    I have just encountered the following problem. I am saving a XML file using the XML Saver. Another BLT reads the file, changes something, and saves it again with the same name.
    The file is saved, but the NetWeaver SAP Log gives the error
    "Unable to write file /usr/sap/<SID>/JC00/j2ee/cluster/server0/apps/sap.com/xappsxmiiear/servlet_jsp/XMII/root/CM/<folder>/file.xml"
    Is it a problem with the new storage mechanism in MII 12? Even if I delete the file first and then save it again with the same name, the error is displayed (though the file is saved).
    Michael

    Hi Mike,
    no, the Debug only says "Begin Action XML Saver" and "End Action XML Saver".
    The action however writes the file, the contents has changed after the BLT has run.
    Well, I have just tried the Text Saver with the same file (name and contents). It also gives the error. I now wanted to delete the folder. The folder disappered from the workbench view, and the Netweaver log says "Unable to process service message".
    I then clicked "publish" on the parent folder and tried to create the folder again, but although the folder was not displayed, the workbench said "the folder already exists". When I start my BLT, it could write the file into the folder which then reappeared in the workbench.
    Hm, maybe our installation has some problems? Feels like missing authorizations...
    Michael

  • Unable to write settings

    i have recently perchase the phone palm pixi plus after os updating it is asking for Internet apn i m using mobilink pakistan sim kindly do guiede me what whould i have to do coz when ever i have entered mobilink apn its shows a message that unable to write settings.
    Post relates to: Pixi Plus p8wu0 (AT&T)

    Have you spoken with your providor regarding the issue? You may have incorrect settings. I would suggest you contact your carrier and report the issue with them first. 
    Have you tried a restart or any erases of the phone?
    For reference purposes, click on the following link for the support page for your device on the kb.hpwebos.com webpage.
    http://kb.hpwebos.com/wps/portal/kb/na/pixi/pixi/att/home/page_en.html
    There are links on the page to the user guide, troubleshooting, how to's, downloads, etc.

  • Getting "Unable to write cache file" message in DW CS4

    I was having some issues with a Javascript message, so looking for possible solutions, I came across “Deleting a Corrupted Cache File” in the Index to Dreamweaver FAQ located on this forum. I decided to give it a shot and carefully followed the instructions on my Windows XP, deleting the suggested cache file in my Configuration folder. That didn’t help make my Javascript message go away, though I did eventually find a work-around for that issue.
    However, after deleting this cache file, I began to get the following message every time I close my program or change sites in local files, “Unable to write cache file ‘C:\Documents and Settings\...” the message ends with the site name and the extension .dws.  If I go to Manage Sites and turn off the Enable Cache button for that particular site, I no longer get the message. But if I turn the Enable Cache Button back on, I get the message again. It gives this same message for all the sites.
    I’m hoping others have had this issue and there is a simple fix. I can’t say for sure that deleting the cache file in the configuration folder caused this, but it was only after that I began noticing the problem, so it would make sense the two are likely related.
    Also, I wonder how important the cache is. I could just turn off the Enable Cache Button for all the sites as a work-around if there's no quick fix and if it’s no big deal.
    -Steve

    I was having some issues with a Javascript message, so looking for possible solutions, I came across “Deleting a Corrupted Cache File” in the Index to Dreamweaver FAQ located on this forum. I decided to give it a shot and carefully followed the instructions on my Windows XP, deleting the suggested cache file in my Configuration folder. That didn’t help make my Javascript message go away, though I did eventually find a work-around for that issue.
    However, after deleting this cache file, I began to get the following message every time I close my program or change sites in local files, “Unable to write cache file ‘C:\Documents and Settings\...” the message ends with the site name and the extension .dws.  If I go to Manage Sites and turn off the Enable Cache button for that particular site, I no longer get the message. But if I turn the Enable Cache Button back on, I get the message again. It gives this same message for all the sites.
    I’m hoping others have had this issue and there is a simple fix. I can’t say for sure that deleting the cache file in the configuration folder caused this, but it was only after that I began noticing the problem, so it would make sense the two are likely related.
    Also, I wonder how important the cache is. I could just turn off the Enable Cache Button for all the sites as a work-around if there's no quick fix and if it’s no big deal.
    First of all, only delete cache files when DW is shutdown.
    Also, there are a few different caches. That article only addresses 1 of them. Take a look at this TechNote to be able to find the Site .dws cache files:
    http://kb2.adobe.com/cps/598/5989f7f4.html
    HTH,
    Randy

  • I am unable to write address in contacts as keyboard does not pop up

    I am unable to write address in contacts as keyboard does not pop up. How do I input address?

    To migrate your data to a new iCloud account go to Settings>iCloud and turn off all synced data (contacts, calendars, etc.), when prompted choose to keep the data on your phone.  After everything is set to off, scroll to the bottom and tap Delete Account.  Next, create the new iCloud account on your phone and turn on syncing for contacts, calendars, etc again.  If prompted, choose Merge.  This will upload your data to the new iCloud account.

  • Unable to write smartlist,  error code 1060301

    Hi Team Members,
    we are trying to use Essbase Studio to create Essbase cube by using relational db tables.
    while doing that we are getting following Error.
    Note:_
    we have tried it with partitioned table & Normal Tables bt result are same.
    rational tables we are using contains varchar2 data type.
    Hirerchy contains : 2 columns SourceID & FileID ---> datatype varchar2
    Measure Hir Contains: 1 column duration ---> datatype varchar2
    Environment:_
    Essbase Studio (11.1.2.1)
    Essbase server 11.1.2.1
    Relational DB: Oracle 10g R2
    eRROR:_
    Specified smart list missing name NoData will be ignored
    Specified smart list out-of-range name OutOfRange will be ignored
    Record #3752 - Unable to write smartlist 4203, error code 1060301*
    Deployment Log_
    Member load for dimension RedPSHIR started at: Sep 22, 2011 12:25:38 PM PKT. Records processed: 2,163.
    Member load for dimension RedPSMHir started at: Sep 22, 2011 12:25:50 PM PKT. Records processed: 3,751. Records rejected: 3. Member load elapsed time: 26 Seconds.
    Data load started at: Sep 22, 2011 12:26:05 PM PKT.     Data load elapsed time: 15 Seconds.
    The error file is located on the server at: C:\Oracle\Middleware\EPMSystem11R1\products\Essbase\EssbaseStudio\Server\.\ess_japihome\data\TEST.Plan1_09-22-11_12-25-36.err
    Failed to deploy Essbase cube.
    Caused by: Failed to load data into database: Plan1.
    Caused by: Cannot get async process state. Essbase Error(1042017): Network error: The client or server timed out waiting to receive data using TCP/IP. Check network connections. Increase the olap.server.netConnectRetry and/or olap.server.netDelay values in the essbase.properties. Restart the server and try again.
    TEST.Plan1_09-22-11_12-25-36.err file output_
    Specified smart list missing name NoData will be ignored
    Specified smart list out-of-range name OutOfRange will be ignored
    Record #3752 - Unable to write smartlist 4203, error code 1060301
    Regards,
    Alee

    Hi guys,
    I think the issue was due to using varchar2 datatype column (duration) for measure Hirerchy.
    after converting it into number (using view option in rational DB) & doing the whole process again. it works fine
    Reference section (Note):
    rational tables we are using contains varchar2 data type.
    Hirerchy contains : 2 columns SourceID & FileID ---> datatype varchar2
    Measure Hir Contains: 1 column duration ---> datatype varchar2
    Regards,
    Alee

Maybe you are looking for