K7N2 Delta-ILSR 3200 barton 400fsb reboots

hi all
Just got a new Athlon XP 3200 *400FSB* barton for xmas
BUT my system restarts about 2 minutes into xp
the does it again after 1 minute etc etc
my fsb set to 200 mhz - jumppers to 133/166 and usermode default
i have to clock system to 166 to get stable again
any ideas
my system spec is
K7N2 Delta-ILSR - bios v7.8
Athlon XP 3200 *400FSB* barton
1 Gb (2 x 512Mb) Corsair TwinX-XL, DDR PC3200XLPRO
radeon 9800 pro 128mb
2 x 80gb ibm sata

Quote
i have a 400w encer psu
Specs (amps)? Look at my sig to see which numbers we need.
Quote
thematake heatsink (nice one)
A nice one, aha...but that doesn't say too much about it's function
An amd approved type?
Please read Trouble shooting guide! Read this first!!!! rev 13-1-2004 about headsink mounting.

Similar Messages

Help! amd xp3000+ barton temp's.... k7n2 delta ilsr

Hi all, (sorry for the lengthy post)
Ive recently built a new system based on the K7N2 DELTA ILSR, great mobo, however my cpu temps are extremely high! on idle 48C and on load nearly 60C. the mobo temp hits approx 40c on load and 34 on idle.
I had an issue with cooling as the cpu heat diode would freeze my pc as it was hitting temps of 58c on idle. i was using the coolermaster aero 7+.... no good at all!!!!! even when on full rpm. Now im using a vantec 80mm fan on a Thermalright SLK-800A. much improved, however still extremely hot.
after reading this review (section headed: Heat Dissipation: Thermal Conditions and S2K Bus Disconnect) :
http://www.xbitlabs.com/articles/cpu/display/athlonxp-3000.html
......on "S2k bus disconnect" created by AMD for the barton range.
As the article states, it reduces Cpu temps ALOT!! but im not too sure ion how to activate it or even if my MSI motherboard supports it....
Can anyone shed some light???
system:
Radeon 9800
1GB 3200 Ram
xp 3000+ Barton
Sound Audigy 2
Thanks, Sav

Sorry about the long reply!!! the first thing i would like to say is why does this happen at 58C even with the bios temp settings diabled??? pehapes MSI could Answer this?
I have spent countless hours trying to fix this problem and a lot of £££. A bit of background to me I am a design engineer and i like my PC to work well. I have the following main components
xp3200+ based system (Max die 85C)
with dual 512ddr sticks running at 400mhz
Matrox Parphilia
10K SATA hard disk
7,200 133ATA hard drive
Plus motherboard Nvidia chipset
these all kick out a lot of heat the (CPU contributing 76.8w).
first i started out with a very cheap case and standard amd heatsink. I found after about 5 minutes my pc kept crashing i automatically thought that it was probably the case temperature so monitored this found every time cpu reached 58C it crashed on the dot. The only conclusion i can draw from this that this MB has some thermal protection that can not be switched off but i am guessing perhapes MSI would like to answer this.
I quickly decided as an engineer that the best thing would be to go and buy a aluminuim case with lots of case fans (Basically a big heatsink itself). After a lot of searching i settled for a Coolermaster ATC110. It has four case fans all run at full speed all the time. Now this stoped the crashing problem it only now crashes if i put it under continous loading. Then i went out and bought a new cpu heatsink to replace the amd standard one. This had a minor effect on cpu temp but again under high loads the system crashed at 58C. Obvoiusly as an engineer i satred to think that the amount of noise the system with all its fans going at max is like being put in a wind tunnel.
I then turned to looking at the thermal diserpation requiremnts of all the bits in my system. I worked out that i need to disserpate 281Wmax of heat with my current setup. The kind of heat a small electric fire produces!!!. I begun to wounder if i could shift enough air through the two exhaust fans at the rooms ambient temp to do this. After some calculations I found that my case exhaust case fans are only just surfficent to disspate this amount. Which could explain this the crashing. because the higher the case temp the lower the capability of the heatsinks to conduct heat away from the item.
In the end i gave up with active cooling methods (heatsinks and fans) and realised my only option was to go for external cooling. I now have the system setup with a koolance exos cooling both hardisks graphics card cpu and MBchipset. I know this is very extreme but the case fan noise got to me now i have disconected all case fans except for the ones in my thermaltake power supply which are virtually silent. After about 12 evenings of testing and installation I now have a system which is not only stable but the CPU temp is only 32C.
Obvoiusly getting the heat out of the case is a good idea. The Exos is only running at it's lowest setting which means the fans arnt making any noticable noise.
MOST IMPORTANTLY IT DOES NOT CRASH ANY MORE. AND THERE IS THE PSSIBILTY OF OVERCLOCKING.
The question still remains though why 58C?

K7N2 delta ILSR VS Athlon 3200+

Will I be able to install Athlon 3200+ on my K7N2 delta ILSR ver 1a board?

thats what i got runs fine good combo i think
with some decent ram
etc

MSI K7N2 Delta-ILSR Nforce2 (Socket A) Motherboard (MB-003-MS) Features NF2 chip

I tried to install 3 of the Crucial Ballistix Tracer (1 Gig Each) in this motherboard (MSI K7N2 Delta-ILSR Nforce2 (Socket A) Motherboard (MB-003-MS) Features NF2 chipset) and it will not run stabilly no matter what I tried. Is this a bios conflict with the memory? If so, are there any new bios updates? I have tried cas settings and voltage settings but nothing works. It will how ever run perfectly with only 2 sticks in single channel mode. It will not run same 2 sticks in dual channel mode. Anyone have any ideas? Anyone know of any new motherboards with maybe NFORCE 4 Chipset that support all 3 sticks of this memory and an AGP graphics card? Im thinking of a new motherboard but I still need to have AGP and SATA.
Barton 3200 core proc.
System has ran fine for a solid year until I tried new memory. Please help!

Quote from: freakytiki4u on 07-November-06, 23:42:33
Ok I tried to use relaxed FSB by -10 and relaxed mem timings but still unstable due to the motherboard trying to use dual channel memory. If you can modify the bios to where it will not have the capability of dual channel memory I truly believe it will work. Will u try this for me? I would greatly appreciate it as I am really not ready to spend all the money on new equipemtn when this suits my needs for now.
sure but as i said before this is gona be experimental and risky. Here we go:
MSI K7N2 Delta ILSR Experimental MOD E1(Disable Dual CH ability)
Procedure is automated in best possible safest way to BIOS update.
Prepare a blank diskette in a good condition(newest one etc.)
]execute file under XP will make bootdisk with automated BIOS update procedure. when diskette is ready, reboot PC and boot from FDD(floppy), wait a bit, then you will be asked for final confirmation about BIOS update process, press a key to proceed, after BIOS update is complete, ensure that you got successfully output message from flash program. then power down your PC, remove power cord from the PSU, hit power button several time to drain caps electrify, touch with hands some metal for ES discharge, and Clear CMOS.
pull back power cord, power up your PC, when you see CMOS checksum error,(expected msg) hit F1 to continue to re-build DMI pool data, then reboot and enter in BIOS, LOAD BIOS DEFAULT, and SAFE AND EXIT.
NOTE: Ensure your PC is stable before proceed with BIOS update.
NOTE: Use it at own risk, chance of failure is big, cannot guarantee results and safest as provisional mode which can guarantee it will work stable with features. also cannot test it personally before give you. (don't have mobo anymore)
Using it may end with dead mainboard (BIOS chip re-flash will be required, if somethink goes wrong)

Strange phantom restarts on MSI K7N2 Delta ILSR

Just wanted to see if I could get opinions on this. My MSI K7N2 Delta ILSR mobo runs real nice now, but still, on occasion, very rare and intermittently, it will just restart. Not likely a heat issue, as the temps are nice and low. Also, not just happenning when I'm playing a game or anything strenuous. Did it once while checking email, once during install of an MS Office program, and once during a game. Could it be my old Gforce 2 MX 200 video card, as the picture sometimes gets wavy (like fine waves on an ocean), and the old computer it was in did similar things, or is it common with this mobo.
MSI K7N2 Delta ILSR
Athlon XP 2500+ Barton
1026 MB Kingston DDR RAM (2x512 Dual)
Gforce 2 MX 200 AGP 4x
WD 60 GB 7200 RPM

I had errors on test 4 not 5 with Winbond 2-512 Dual Channel called Hardcore Cooling and they said that getting errors with memtest86 may not mean that the ram is defective, it may not be compatible with the memory comtrol and they had me RMA it back. I also was not able to run the ram stable at there advertized rate of 6 2 2 2 it was only stable at 8 3 3 2.5
I replaced it with OCZ after talking to there Tech support people about compatiblety problems with the Nvidia chipset. Sense I installed the OCZ I only had one ram reboot and when I checked I was running the voltage at 2.5 and OCZ said that I should be running at 2.6. They also said that I could run it up to 2.8 with no worry.
Look on manufactor web site to see what ram timing yours should be running at and what voltage, Auto setting in Bios is not always the best setting.
If it still not stable at manufactor spec than I'd talk to who ever you bought it from about replacing it or refund and buy something thats on the Nvidia compatible list.
Most ram manufactors have a list of motherboards that there ram will work on but sometimes the newer boards like K7N2 or not listed yet as still working that out.

MSI K7N2 Delta ILSR - RAID BIOS Option ???

hi ho,
i have my 2 storage devices pluged into the promise 376 onboard controller. they are not connected as a real raid (not mirror nor real stripe). my OS is win2k on the first sata device and everything was fine for a long time.
but now when my system boots, it detects the ide drives and then i see the irq board.
right after that the system stops and tells me 'disk boot failure'. so i don`t get the chance to configure my raidcontroller or my sata devices.
it is as the controller is deactivated. i remember a bios version where you could activate and deactivate the sata controller. but in my bios (right now it is v7.8) there is no such option.
i have tested so far:
- reset cmos
- flash bios v7.5 to 7.8
- disconnected sata drives
anyone with similar problems or any suggestion?
> MoBo : K7N2 Delta-ILSR Bios v7.8
> CPU : AMD Barton 2500+ (not overclocked)
> Ram : TwinMos 1GB 3200 400Mhz
> Sata : 2 x Maxtor 120GB Sata (as single Devices on Raid-Controller)
> Ide : 60GB IBM DeckStar
> Gra : ATI 9600 pro 128MB
> Aud : SB Audigy 2 ZS
> Pow : SilverPower 350W, +3,3V/+5V@25A and 12V@18A
> OS : win 2000 SP4 + Security Updates 31.07.04 + DirectX 9.0c

watch the bottom of the screen after pressing Enter on the "Welcome to Setup" screen. There will be some moments of files being loaded, and then you should see a message appear which says "Press F6 if you need to install a 3rd party SCSI or RAID driver". This message will only stay on the screen for a couple of seconds, so press F6 as soon as you see it appear. After this is done, you will see other messages appear, and it will act as though nothing is happening, but eventually a screen will appear which will allow you to install the drivers for the sata controller.
specify a device press S, select "win 2000 promise fasttrak 376 controller" it will read floppy and load, dot not remove floppy yet, continue win2000 install it may nead to access floppy to finish installing raid driver, did you do it like this.
try making some floppy boot disks and boot to floppy instead of cd.
http://freepctech.com/pc/002/files010.shtml
when you say there not listed, where did you see this? they wont be listed, windows will search for fasttrak controller so it will see sata's conected to it with out you knowing, so long as you load the controller from floppy that came with mobo as above.

MSI K7N2 Delta-ILSR (MS-6570) BSOD problems grrr

I recently purchased this board and although it is an awesome product, I'm having a problem with BSOD's when I play a game for a certain period of time
Specs:
MSI K7N2 Delta-ILSR (7.6 BIOS)
AMD Athlon XP 2800+ Barton
512MB (2x256MB) Samsung PC-2700 DDR memory (2.5-3-3-6 1T)
MSI 128MB GeForce4 Ti 4200 (4X AGP)
NVIDIA nForce on-board sound
Western Digital 80GB drive w/ 8MB cache
MSI X48 CD/CD-RW/DVD combo drive
Windows XP Professional SP1
PSU:
Turbolink 420watt (came with case)
+3.3V is 28A
+5V is 40A
+12V is 18A
So what happens is I get a STOP error during the game that shows the kmixer.sys driver as the culprit. Sometimes it's accompanied by PAGE_FAULT_IN_NON_PAGED_AREA too. I read somewhere that kmixer.sys has to do with windows audio and that it's a 3rd party driver issue or a memory issue. I'm using the latest NVIDIA 3.13 nForce platform drivers. I ran Memtest lastnight for 12 hours straight and 0 errors. I'm thinking the memory may not be compatible with the board nor dual channel, is this possible? I have also tried several different drivers for both video and chipset including MSI's own and I still get the kmixer.sys BSOD when playing games. My previous motherboard was an MSI KT3 Ultra2-R (MS-6380E) which I had no issues with. Any help would be greatly appreciated. Thank you in advance.
--Update--
I just tried to play a game with audio disabled and it crashed this time with DRIVER_IRQL_NOT_LESS_OR_EQUAL with nv4_mini.sys as the problem. My IRQ table shows some sharing, but device manager shows no conflicts.

Ok I tried running the DTM-CB3 module which is nForce2 approved at 3-4-4-11 2T timings and experienced the same result even at 2.6 and 2.7v. I tried both in dual-channel and same thing happened. However, I downloaded a program called Prime95 and ran the CPU torture test and the system returned a fatal error within the first few minutes. CPU Temp was at 57 C and the warning beep (set to 60C though) sounded intermittentley which is strange. I let it cool down then ran the torture test again and about 5min. later the system either seized completely or the program crashed. IE has also crashed randomly on me. I did this several times, before trying a different FSB/DRAM ratio. So I left the system at 200 FSB and used a 6:5 ratio so my memory was running at DDR333 and processor was a 3200+. I ran Prime95 again and the system locked up just as it did the other times. So after I did this a few times with consistent results. I went back and set the FSB to 166 and tried a 5:6 ratio so the memory was DDR400 and processor was the normal 2800+. I ran it again and to my suprise it passed all the tests and after an hour of this, I tried a game and that was perfectly fine as well. I checked the temps and CPU was only 45 C this time. So I'm thinking the processor can't handle anything above 50C or it's just plain overheating. I ordered a Thermaltake Silent Boost HSF today which is tested up to 3400+ so this should fix my problem. If not, then I'm going to replace the memory with a 512MB Geil PC3200 golden dragon dual-channel kit.

MSI K7N2 Delta-ILSR Wont boot up (no display no bios)

Hi
i bought a AMD Athlon XP 3200+ & MSI K7N2 Delta-ILSR.
unfortuntly i can't boot it. it wont show anything on screen.
i have tried anything i red in this forum (clear cmos... safe mode jumper...strip all parts...)
all i get is :
blank black display, no beeps and keyboard lights flashes over and over (when connected to a KVM hub), when conected directly to keboard the lights flashes only once but stil black display and no beeps (i hear on speake,when powering up PSU, a silent short noise, no beep).
power suply turns on (new one 500w), i tried agp video card and replaced with pci video card.
memory is kingstone 512mb pc3200 400MHz x2, i tried only one of them and both in diferent sockets.
cpu: AMD xp 3200+ 400fsb.
i did succed to go into bios only once, after lots of resets and shutdowns and bios clear (after ouers)
i choosed in the bios: load bios defaults, and thats it. i hoped it starts up but nothing.
i did all testing i know (checked all pins, cables, clear cmos...all, you name it)
all parts are brand new (except motherbord. it's seconds hand from eBay. i've bean talled that it works fine)
i also e-mailed MSI support that question. (2 days ago. no answer yet)
oh...and i have a pci POST diagnostic card and its 7seg display don't shows any numbers, only when once i succed to get into bios. i don't have the msi original D-Breket addon diag.
can you help me?

hi guys
here is my PSU specs:
Colors-It 500w-Max Silent ATX Power Supply
Voltage 115/230V
Current 10A/5A
Frequency 60/50Hz
+3.3 +5 +12 -12 -5 +5SB BLK GRN GRY
30A 50A 15A 1.0A 1.0A 2.5A COM P-ON PG
connectors:
ATX-2.03 Connector: 1
ATX-12V Connector: 1
CD-Rom/HD 4 Pin connector: 6
Floppy 4 Pin Connector: 2
Serial ATA Connector : 1
cpu: AMD Athlon XP 3200+
MotherBoard: MSI K7N2 Delta-ILSR More: http://www.msicomputer.com/product/p_spec.asp?model=K7N2_Delta-ILSR&class=mb
Memory: kingstone 512mb pc3200 400MHz x2 More: http://www.ec.kingston.com/ecom/configurator/PartsInfo.asp?ktcpartno=KVR400X64C3A/512
i have other brand of memory moduls (micron pc2300) i tried them too. no go.
i tried other PSU, i pulled from my brothers pc (amd xp 1400+).
as i said before, i have pci POST diagnostic card so it could tell me any problem. iguss it's the mobo, posibly bios upgrade.
but if mobo not showing bios, i can't update bios from floppy.
and the tested the mobo out side the case on a antistatic mat and i useed an antistatic strip.
as i said i could get into the bios once, after many resets....choosed 'load bios defaults..', restarted and.....no go.

K7N2 Delta ILSR won't boot from FDD or HD

I have a serious problem with my new K7N2 delta ILSR based computer.
My machine is
K7N2 delta ILSR 400W
3.3/25 5/32 12/15 V/A PSU
512+256 MB A-data 3200 ram
Athlon XP2500+
BTC 48x24x48 Combo
100 mb Zip int. -disabled
120 GB Seagate barracuda SATA-disabled
120 GB Seagate Barracuda parallel
Triplex parasouls ATI 9600PRO 128MB
The machine POST's normally with all 4 lights doing what they should.
The Promise BIOS can detect the SATA drive correctly but when an attempt is made to write the array an error- 'error modifying array- system is going to reboot- press any key to reboot>" is given.
The M/B BIOS detects the FDD and Seagate Parallel drives correctly but when a correctly formatted XP boot disc (or Mandrake Linux or Caldera DR-DOS) is placed in the floppy drive a "no system disk" error is given.
When you F6 to install RAID drivers in the Windows XP install and the screen comes up where you are prompted to insert the floppy there is no mass storage device detected.
I purchased a new FDD and it gives precisely the same error as the original.
I installed the parallel Seagate in another system and installed and activated windows XP on it. After re-installing it in the K7N2 system I was disappointed to discover that it will not boot off the hard drive. When you boot from the XP CD the machine locks up. (Disconnecting the HD it will boot normally)
This is a real puzzle as it is possible to format the hard drive using Max Blast3- the maxtor disk utility which is based ( as is the Seagate Seatools utility) on Caldera DR-DOS). And I can't see why it should boot from a CD-ROM and not from any other correctly formatted boot disk.
I suspect a problem in either the (South?) bridge that controls the peripherals or the BIOS. I am at a loss how to re-flash the BIOS with out the use of the floppy drive- unless this can be done from a CD-ROM.
The PSU is not being strained and nForce list both RAM sticks as OK.

Quote
Originally posted by Wonkanoby
is the fd light on all the time,as that means the ide type lead needs flipping 180 degrees in the back of it
is the hard drive ide 80 wire ,blue end in the board
any thing shorting under the board,an extra stand off or the like
The Fd light behaves normally. i.e. lights up when the drive is being accessed.
has anybody else noted that the FDD is B by default- That the cables have a few wires twisted like the wires between the first and second plugs on the old cables?
The IDE 80 wire(counted!) is long end in the board- my plugs are all 3 black. You can't put them in the wrong way becaue of the centre key.
All the stands are plastic except for two brass ones that are in the centre of the board that go to circular mount pads. That is how the case came and I thought it was a design feature.
The thing I find most puzzleing is that i can boot a caldera based system that finds everything including the floppy- and read it- (provided you call it drive B!) yet naything DOS based won't go- I have this feeling that it has a screwed up DOS call that is not looking in the right disk sector for NTldr or whatever to boot. I think this is a bios problem- but I am not sure how to find out when you can't boot from the FDD.
My brother has talked to some tech friends and there word is that this is a weird one- probably a dud board RTS.

Problem with K7N2 Delta ILSR?

Hi
Not sure if there is a problem or not but I have:
K7N2 Delta ILSR
Athlon XP 2.8GHz
512Meg Ram
Win XP SR2
When I check in System Properites, on the General Tab, at the bottom though it reports I have a AMD Athlon(tm) XP 2800+, correctly, however underneath it says "2.08 GHz, 512 Mb RAM".
What happened to the other 0.7 Ghz !
In the BIOS, the FSB is set to 166 Mhz as recommeded. If set to 100 MHz, in the BIOS the clock speed appears as 1250Mhz! Surely that's not right.
I know it wont run at the full 2.8 GHz but I thought it should only be a little less than that? Is this normal?
Many Thanks
Salvo
[email protected]

Salvo,
Here are some CPUs and their speeds:
2100+ 1.73GHz (TBred)
2200+ 1.8GHz (TBred)
2500+ 1.83GHz (Barton)
2600+ 1.9GHz (Barton)
2700+ 2.17GHz (TBred)
2800+ 2.08GHz (Barton)
3000+ 2.16GHz (Barton 333Mhz FSB)
3000+ 2.1GHz (Barton 400Mhz FSB)
3200+ 2.2GHz (Barton)
Take Care,
Richard

Upgrade to K7N2 DELTA-ILSR help

Thinking of purchaseing the K7N2 DELTA-ILSR board and would like some help verifying the hardware i have not having any problem with this mobo.
AMD|2800/333 ATHLON XP BARTON
MEM - DDR Corsair dual 512MB X2 KIT|VS1GBKIT333
Soundblaster 5.1 Platinum
Liteon 52x32x52 r\rw
80GB|SEAGATE ST380011A 7200
60GB|SEAGATE ST360015A 7200
PSU- Super-Flower Silent TT aluminum 450W ATX power supplyTTGI TT-450SS (450W). AC Input: 100~120Vac/200~240Vac, 10/6A, 60/50Hz. DC Output: +3.3V~28.0A, +5V~42.0A, +12V~18.0A. +5Vsb~3.0A, -5V~0.5A, -12V~0.8a). MAX OUTPUT POWER: 450W. Cooling: Air convention by +12V DC fan. 10 IDE connectors, 2 floppy connectors, +12V power connector, Aux power connector
CPU FAN - OCZ GLADIATOR 3 Socket A/462 up to Athlon XP 3200+. Single-piece pure copper construction. Dimensions: 60x60x30mm. FAN: 60x60x25. Medium-speed. Or: 60x60x25 Quiet. High-speed. Voltage: 12 Volt. Ball bearing fan
Video Card - Chaintech VGA GF FX5700 SA5700 256M
It looks like a great board and i see some great reviews but also see alot of small issue with compadability. It looks like the 1st thing is to upgrade the bios, and hope i don't have any issue with my cable modem box (guess i could put my old network card back in and disable the mobo's built in net work if there is problems).
I don't do O\C so nothing to worry about there. My old board is an Epox and is max'd out with no future upgrade room, so that's why i'd like to upgrade.
Thanks for any help guys.
rider

rider45,
If you do not need the Break Out Box from the Platinum, I would go with the onboard nVidia SoundStorm. It sounds better than the old Live! and uses less CPU Cycles.
Take Care,
Richard

K7n2 delt ilsr instabilty problem update

have a k7n2 delta ilsr have an issue where it is unstalble ie get bsod at welcom etc at 400 fsb ie 200 setting in bios will run at 166 in safe mode the 3200 cpu is reconised as at 2.39 ghz it should be 2.2 ghz if i run cpucz it says the multiplier is *12 is this a motherbord fault have updated bios too 7.8 latesed have tried diff make of memory power supply but i think the problem is looking me in the face in the fact that the cpu is reconised as 2.39 ghz and the muilt is *12 i think it should be * 11 can any body help regards bazer

yes has latesd bios    AMD Athlon(tm) XP 2700+ here is some info pc wizard 2005
Codename :   Barton
Revision :   A2
Technology :   0.13µ
CPU ID :   6.A.0
CPU IDEx :   7.A.0
Features :
VME - Virtual Mode Ext. :   Yes
DE - Debugging Extension :   Yes
PSE - Page Size Extension :   Yes
TSC - Time Stamp Counter :   Yes
MSR - Model Specific Registers :   Yes
PAE - Physical Address Extension :   Yes
MCE - Machine Check Exception :   Yes
APIC - Local APIC Built-in :   Yes
SEP - Fast System Call :   Yes
MTRR - Memory Type Range Reg. :   Yes
PGE - Page Global Enable :   Yes
MCA - Machine Check Architecture :   Yes
PAT - Page Attribute Table :   Yes
PSE36 - 36-bit Page Size Extension :   Yes
PSN - Unique Serial Number :   No
DS - Debug Trace & EMON Store :   No
ACPI - Software Clock Control :   No
SS - Self Snoop :   No
TM - Thermal Monitor :   No
HTT - Hyper-Threading :   No
SBF - Signal Break on FERR :   No
MON - Monitor/Mwait :   No
DSCPL - CPL qualified Debug Store :   No
TM2 - Thermal Monitor 2 :   No
CID - Context ID :   No
EST - Enhanced SpeedStep Tec...   No
NX Bit - No-execute Page Protec...   No
VMX - Vanderpool Technology :   No
Miscellaneous :
FPU - Co-processor Built-in :   Yes
CX8 - CMPXCHG8B :   Yes
CX16 - CMPXCHG16B :   No
CMOV - Conditionnal Move Inst. :   Yes
CLF - Cache Line Flush :   No
FXSR - Fast Float Save & Restore :   Yes
DAZ - Denormals Are Zero :   No
MMX Technology :   Yes
SSE Technology :   Yes
SSE2 Technology :   No
SSE3 Technology :   No
X86-64 Technology :   No
AMD MMX Technology :   Yes
3DNow! Technology :   Yes
Extended 3DNow! Technology :   Yes
3DNow! Pro Technology :   Yes
SMP - MP Capability :   No
Power Status :
Voltage Control :   No
Frequency Control :   No
Thermal Sensor Built-in :   Yes
Addressing Information :
Physical Addressing max. :   34-bit
Linear Addressing max. :   32-bit
Mainboard Upgradebility :
Socket/Slot :   Socket A
Upgrade interface :   ZIF Socket
Supported Speed :   2200 MHz (or more)
Supported Voltage :   1.6V
al Information :
Performance Rating :   PR-3300 (estimated)
Real Frequency :   2164.89 MHz
Multiplier :   12x
Front Side Bus Information :
FSB Frequency :   180.4 MHz
Bus Speed :   360.8 MHz (DDR)
Initial Frequencies :
Frequency :   2000 MHz
FSB Frequency :   166 MHz
Control Clock Frequency :
Type :   None
Thermal Information :
Core Power :   63.42 W (estimated)
Resistance :   0.46 °C/W (estimated)
Processor Performance Information :
Throttle Mode AC :   None
Throttle Mode DC :   Adaptive
Current Configuration :   None
Throttle :   2164 MHz
CPU Throttle Temperature :   60°C
CPU Shutdown Temperature :   100°C
eneral Information :
A0 (RAS 0) :   256 (Single Bank)
A1 (RAS 2) :   256 (Single Bank)
A2 :   Empty
Memory Controller Information :
Memory Controller :   Standard, EDO
Number of connectors :   3
Max. Module Size :   32 MB
Max. Memory Size :   96 MB
Supported Speed :   70ns, 60ns
Supported Voltages :   5v
Error Detection Method :   8-bit Parity
Error Correction Capability :   Unspecified
Current/Supported Interleave :   1-way/1-way
Chipset Information :
Type :   DDR-SDRAM PC2900
Frequency :   180 MHz
FSB/RAM Multiplier :   1/1x
Channels :   Dual
ECC Diagnostic :   No
CAS Latency (tCL) :   3 clocks
RAS to CAS (tRCD) :   3 clocks
RAS Precharge (tRP) :   3 clocks
Cycle Time (tRAS) :   8 clocks
Information SPD EEPROM (A0) :
Manufacturer :   Samsung
Part Number :   M3 68L3223ETM-CCC
Serial Number :   F6016243
Type :   DDR-SDRAM PC3200 (200 MHz)
Size :   256 MB (1 rows, 4 banks)
Module Buffered :   No
Module Registered :   No
Width :   64-bit
Error Correction Capability :   No
Max. Burst Length :   8
Refresh :   Reduced (.5x)7.8 µs, Self Refresh
Voltage :   SSTL 2.5v
Supported Frequencies :   166 MHz, 200 MHz
CAS Latency (tCL) :   2.5 clocks @166 MHz, 3 clocks @200 MHz
RAS to CAS (tRCD) :   3 clocks @166 MHz, 3 clocks @200 MHz
RAS Precharge (tRP) :   3 clocks @166 MHz, 3 clocks @200 MHz
Cycle Time (tRAS) :   7 clocks @166 MHz, 8 clocks @200 MHz
Information SPD EEPROM (A1) :
Manufacturer :   Samsung
Part Number :   M3 68L3223ETM-CCC
Serial Number :   F6056193
Type :   DDR-SDRAM PC3200 (200 MHz)
Size :   256 MB (1 rows, 4 banks)
Module Buffered :   No
Module Registered :   No
Width :   64-bit
Error Correction Capability :   No
Max. Burst Length :   8
Refresh :   Reduced (.5x)7.8 µs, Self Refresh
Voltage :   SSTL 2.5v
Supported Frequencies :   166 MHz, 200 MHz
CAS Latency (tCL) :   2.5 clocks @166 MHz, 3 clocks @200 MHz
RAS to CAS (tRCD) :   3 clocks @166 MHz, 3 clocks @200 MHz
RAS Precharge (tRP) :   3 clocks @166 MHz, 3 clocks @200 MHz
Cycle Time (tRAS) :   7 clocks @166 MHz, 8 clocks @200 MHz

Someone plz help me with my k7n2 delta-ilsr

Hey everyone,
I just put my sytem togother and ran into a problem. I got the system to boot up just fine. It was not until I tried installing windows xp proffesional that I ran into problems. The installation process runs pretty smoothly, until the computer reboots to run windows for the first time. After it reboots the windows logo appears and the after 2 seconds or so, a blue screen appears saying that windows was shut down to prevent any damage to my computer. I have never encountered this problem before when I built other systems. The screen suggests that I should check my HDD's for viruses or check to see if they are configured correctly. The HDD's are SATA and I have them set up in RAID 0 mode and yeah I installed the RAID drivers during the installation process. Thinking that I had made mistake setting up the SATA drives, tried installing windows using a regular IDE hard drive and it gave the same message. I am stumped anybody have any ideas of what I might be doing wrong? Any help would be appreciated . My system specs are below.
MSI k7n2 delta-ilsr mobo
AMD 3000+ Athlon XP cpu (333 fsb)
ATI Raedon 9000 ( I know it's crappy , I'm still saving up for the ATI all in wonder 9800 )
x1 kingston 512mb pc3200 DIMM
x2 maxtor 80gb maxtor hdd's
x1 regular cd-rom drive
x1 floppy drive
420w raidmax psu
(+3.3v = 26A, +5v = 32A, +12v=13A)

Memory that comes with timing of 5 2 2 2 or 6 2 2 2 or usally winbond BH-5 memory chips. Ones with 5 3 2 2 or CH-5 winbond chips. The BH-5 chips overclock a little better than the CH-5. (Muskin uses BH-5 winbond in there black ram)
Winbond is no longer making BH-5 chips but is going to make a limited run of them as demend is high for them.
The first number shown here is the Traz and it controls the flush timing bench testing is showing that a higher number of 9, 10 or 11 or getting better bench results than the 6 or 5. Thats with Dual Channel memory.
The timing you show probly should be something like 8 3 3 3 or 8 3 3 2.5 unless it is there faster Dual channel ram.
The timing numbers can also appear like this 2 2 2 5 the high number is the Traz either way.
Look on your memory manufactor web site for the timing that if should run at also look at the voltage as this can make a big differance.

HELP me with my K7N2 delta ilsr

Can anyone help me with this problem. I have just upgraded to MSI's K7N2 delta ilsr motherboard. Its all working quite well apart from the fact that the pc wont start up from cold....at all.
When I start the pc from an off state, it runs up the fans and drives, but does not post.
The diagnostic led pannel on the back of the pc shows that the cpu is faulty or not installed correctly.
If I then press the reset button, the pc posts, and boots up just fine.
It does this EVERY time I start up.
I have tried re installing the cpu, which is an XP 2800+ 333 barton, but to no avail.
I have asked a few questions on other forums, but I cant solve it.
These are the suggestions so far.
1. the psu (I have a Tsunami 400 atx psu) could not be giving out enough power on initial startup, but once the pc is running, it has enough to boot the pc from a reset.
2. The mobo or the bios could be at fault. I have not flashed the bios, or upgraded it in any way from original, so is there an issue with the original bios on these boards, and 2800 barton chips??? Could it be a mobo fault? The pc runs fine once the machine is booted.? how do I test it?
3. The cpu could be faulty? but would this not stop it running fuull stop?
4. my ram. I have a single stick of OCZ 512mb pc3200 ddr, which I was told would make the pc fly. Not shure on that statement, but is this ram compatible?? could this be the problem?
Im fairly new to the upgrade side of things, and I need some help with this one.
Also, Id be really greatfull if some one could talk me through flashing my bios to the latest version, as the thought of doing this narks me a bit...I dont want to mess it up and get a dead pc...
HELP

+3.3v 14A
+5v 28A
+12v 16A
+5vsb 2A
-5v 0.5A
-12v 0.8A
Hope this helps, as my pc seems to be living with its case off a lot these days..haha

Data corruption on MSI K7N2 Delta ILSR

Hi all,
Just got my new MSI K7N2 Delta ILSR up and running.
Got some issues with the memory running at 200mhz while the Barton core of my Athlon Xp 2600+ was running 166mhz, this had to be 1:1 (thx forum )
While running the default bios settings with cpu/mem at 166/166 fsb everything is stable as hell. I have been running Prime95 for 2 days now and using the system for dvd ripping/encoding, UT2004 gaming etc.
Then the overclocking began I'm using the standard AMD cooler that came with my boxed Xp2600+ so I didn't expect an FSB of 200mhz.
I stopped at an FSB of 190mhz...been crunching Prime95 for 18 hours now and again very stable.
Now comes the problem : Sometimes I get crc errors when installing a game or decrypting a dvd!! But how can this be? Prime95 is stable at this 190fsb overclock.
When using an FSB of 166mhz no data corruption or crc errors.
What can this be? It's not the cables because they're all the same as in my old setup which was running (ahum...walking) stable. PCI/AGP speeds are locked when overclocking...
Only thing I can think of is the power supply. I've read in a warning post from Bas that the Q-Tec 550w psu I have is crap. So my guess is PSU, but maybe it's something else I'm forgetting...Any suggestions??
The stupid thing is when I'm not overclocking I don't have the data corruption problems, but I'm still using the same crappy Q-Tec 550w PSU.
Help!
gr,
Remco

Hmmm, that's curious. On the MSI K7N2 Delta ILSR product page Kingston memory is recommended
Ok, did a Memtest86 v1.11 pass at cpu/dimm 166/166 - no problems whatsoever. I think using Prime95 would have revealed memory problems...but will do another pass with cpu/dimm at 190/190.
Can overclocking affect the Promise Raid Controller?? It should be locked like the PCI/AGP but who knows...
Well, I still have to replace my PSU but I'm not 100% sure that this is the problem. What PSU would you recommend? ...and I'm also thinking about replacing the standard CPU cooler, any advice is welcome
gr,
Remco

K7N2 Delta-ILSR 3200 barton 400fsb reboots

Similar Messages

Maybe you are looking for