K7N2 Delta-ILSR can't get IEEE 1394 working

My Mainboard K7N2 Delta-ILSR nForce2 Ultra 400 (601-6570-030)
I can't ever remember seeing the onchip 1394 controller settings in Bios.
I do remember seeing it in windows XP before I reflashed the bios to ver 7.6 using Live Update, I have read about problems with the mainboard not likeing the FX5900 Video cards, so I thought I would update the bios to save any problems.
I then re-installed XP and thought nothing of it. Everything was running well intil I wanted to do some video capturing from my camcorder. I then realised that there where no 1394 drivers installed and no controller could be found. I read the manual and it said to set the 1394 controller in Bios to Auto. When I went to Bios there was no onchip 1394 controller shown in the intergrated peripherals or any where else in Bios.
Can someone suggest what to do next please?

Try the followin steps
 Hit the DEL key to go to the BIOS SCREEN
 goto  LOAD BIOS SETUP DEFAULTS  and press ENTER
 press F10 to save it to BIOS.
NOW  again go to the BIOS  and go to the INTEGRATED PERIPHERALS check out whether there is ONCHIP 1394
All the Best !

Similar Messages

  • Someone plz help me with my k7n2 delta-ilsr

    Hey everyone,
            I just put my sytem togother and ran into a problem.  I got the system to boot up just fine.  It was not until I tried installing windows xp proffesional that  I ran into problems.  The installation process runs pretty smoothly, until the computer reboots to run windows for the first time.  After it reboots the windows logo appears and the after 2 seconds or so, a blue screen appears saying that windows was shut down to prevent any damage to my computer.  I have never encountered this problem before when I built other systems.  The screen suggests that I should check my HDD's for viruses or check to see if they are configured correctly.  The HDD's are SATA and I have them set up in RAID 0 mode and yeah I installed the RAID drivers during the installation process.  Thinking that I had made mistake setting up the SATA drives, tried installing windows using a regular IDE hard drive and it gave the same message.  I am stumped anybody have any ideas of what I might be doing wrong?  Any help would be appreciated .  My system specs are below.
    MSI k7n2 delta-ilsr mobo
    AMD 3000+ Athlon XP cpu (333 fsb)
    ATI Raedon 9000 ( I know it's crappy , I'm still saving up for the ATI all in wonder 9800 )
    x1 kingston 512mb pc3200 DIMM
    x2 maxtor 80gb maxtor hdd's
    x1 regular cd-rom drive
    x1 floppy drive
    420w raidmax psu
    (+3.3v = 26A, +5v = 32A, +12v=13A)

    Memory that comes with timing of 5 2 2 2 or 6 2 2 2 or usally winbond BH-5 memory chips. Ones with 5 3 2 2 or CH-5 winbond chips. The BH-5 chips overclock a little better than the CH-5. (Muskin uses BH-5 winbond in there black ram)
    Winbond is no longer making BH-5 chips but is going to make a limited run of them as demend is high for them.
    The first number shown here is the Traz and it controls the flush timing bench testing is showing that a higher number of 9, 10 or 11 or getting better bench results than the 6 or 5. Thats with Dual Channel memory.
    The timing you show probly should be something  like 8 3 3 3 or 8 3 3 2.5 unless it is there faster Dual channel ram.
    The timing numbers can also appear like this 2 2 2 5 the high number is the Traz either way.
    Look on your memory manufactor web site for the timing that if should run at also look at the voltage as this can make a big differance.

  • HELP me with my K7N2 delta ilsr

    Can anyone help me with this problem. I have just upgraded to MSI's K7N2 delta ilsr motherboard. Its all working quite well apart from the fact that the pc wont start up from cold....at all.
    When I start the pc from an off state, it runs up the fans and drives, but does not post.
    The diagnostic led pannel on the back of the pc shows that the cpu is faulty or not installed correctly.
    If I then press the reset button, the pc posts, and boots up just fine.
    It does this EVERY time I start up.
    I have tried re installing the cpu, which is an XP 2800+ 333 barton, but to no avail.
    I have asked a few questions on other forums, but I cant solve it.
    These are the suggestions so far.
    1. the psu (I have a Tsunami 400 atx psu) could not be giving out enough power on initial startup, but once the pc is running, it has enough to boot the pc from a reset.
    2. The mobo or the bios could be at fault. I have not flashed the bios, or upgraded it in any way from original, so is there an issue with the original bios on these boards, and 2800 barton chips??? Could it be a mobo fault? The pc runs fine once the machine is booted.? how do I test it?
    3. The cpu could be faulty? but would this not stop it running fuull stop?
    4. my ram. I have a single stick of OCZ 512mb pc3200 ddr, which I was told would make the pc fly. Not shure on that statement, but is this ram compatible?? could this be the problem?
    Im fairly new to the upgrade side of things, and I need some help with this one.
    Also, Id be really greatfull if some one could talk me through flashing my bios to the latest version, as the thought of doing this narks me a bit...I dont want to mess it up and get a dead pc...
    HELP

    +3.3v 14A
    +5v 28A
    +12v 16A
    +5vsb 2A
    -5v 0.5A
    -12v 0.8A
    Hope this helps, as my pc seems to be living with its case off a lot these days..haha

  • Internet Connection Problem on MSI K7N2-Delta-ILSR

    Hi, recently I buy an MSI K7N2-Delta-ILSR.I have a problem when I was trying to connect to the Internet through my modem on WinXP Pro SP1. It bring me up an error message 678 ( The computer that was tried to connect did not respond...). I have also a second hard disk with Mel windows. On disk the disk with the Mel I don’t have any problem with the internet connection. All my settings are same on WInXP pro and Mel.I have checked I thousand times. My computer configuration is:
    Athlon XP 2400+ Overclocked to 2205MHz
    2 memory modules of 256MB 400 manufactured by Samsung
    TharmalTake Volcano 11
    Triplex Xabre 400 PRO with 128MB
    Hercules Gamesurrround Fortissimo III 7.1
    Microcom InPorte Home modem 56k
    Leadtek winfast 2000 (TV/FM radio)
    Acard SCSI controller (Acard AEC-6710D) for my scanner
    WesternDigital WD800 GB
    WesternDigital  15.3gb
    Bios ver.7.4  
    Can anyone help me?

    Quote
    Originally posted by Roger Wilco
    Hmmmmm, I\'m also having a problem with the onboard lan of the K7N2 Delta.
    I have an ADSL connection, and have an Alcatel SpeedTouch Home modem.
    I pretty much get the same error as SiliconMan (The computer that was tried to connect did not respond...)
    I ended up giving up on it for the time being, just using my SMC NIC. Would be quite interested in finding out what the problem is though.
    Anyone else in the same boat?
    Hi,
        Your problem is not the same, SiliconMan is trying to connect with a dial-up modem not LAN. Your problem sounds like it may be configuration, do a search on this post, I'm sure you will find people with onboard LAN troubles. It's hard to troubleshoot though since you didn't provide any info about your computer. Good Luck  
    Rob

  • Data corruption on MSI K7N2 Delta ILSR

    Hi all,
    Just got my new MSI K7N2 Delta ILSR up and running.
    Got some issues with the memory running at 200mhz while the Barton core of my Athlon Xp 2600+ was running 166mhz, this had to be 1:1 (thx forum  )
    While running the default bios settings with cpu/mem at 166/166 fsb everything is stable as hell. I have been running Prime95 for 2 days now and using the system for dvd ripping/encoding, UT2004 gaming etc.
    Then the overclocking began   I'm using the standard AMD cooler that came with my boxed Xp2600+ so I didn't expect an FSB of 200mhz.
    I stopped at an FSB of 190mhz...been crunching Prime95 for 18 hours now and again very stable.
    Now comes the problem : Sometimes I get crc errors when installing a game or decrypting a dvd!! But how can this be? Prime95 is stable at this 190fsb overclock.
    When using an FSB of 166mhz no data corruption or crc errors.
    What can this be? It's not the cables because they're all the same as in my old setup which was running (ahum...walking) stable. PCI/AGP speeds are locked when overclocking...
    Only thing I can think of is the power supply. I've read in a warning post from Bas that the Q-Tec 550w psu I have is crap. So my guess is PSU, but maybe it's something else I'm forgetting...Any suggestions??
    The stupid thing is when I'm not overclocking I don't have the data corruption problems, but I'm still using the same crappy Q-Tec 550w PSU.
    Help!  
    gr,
    Remco

    Hmmm, that's curious. On the MSI K7N2 Delta ILSR product page Kingston memory is recommended  
    Ok, did a Memtest86 v1.11 pass at cpu/dimm 166/166 - no problems whatsoever. I think using Prime95 would have revealed memory problems...but will do another pass with cpu/dimm at 190/190.
    Can overclocking affect the Promise Raid Controller?? It should be locked like the PCI/AGP but who knows...
    Well, I still have to replace my PSU but I'm not 100% sure that this is the problem. What PSU would you recommend? ...and I'm also thinking about replacing the standard CPU cooler, any advice is welcome  
    gr,
    Remco

  • FLASH BIOS MSI K7N2 Delta-ILSR ????????

    I am trying to flash the BIOS of my K7N2 Delta-ILSR board. I follwed all the instructions from the MSI Web but I can't get it going. I booted from Win ME & Win98 but could not get into C: drive. So I used Command Prompt from Window to get  into the C: drive and follwed the Flash Bios Procedures. I keep getting the message: AwdFlash No Support WinNT/2000/XP OS
    I got problem with the temp after I updated the BIOS. I wanted to flash it back to the old Bios. Please help me out
    Thank you
    My system:
    WinXP Pro
    MSI K7N2 Delta-ILSR
    AMD 2500+
    1 GB DR3200
    Seagate 160 SATA

    http://www.msi.com.tw/html/support/bios/note/ntfs.htm

  • MSI K7N2 Delta ILSR Memory problems

    I'm trying to burn in a system in a 50 deg C (122 deg F) room for a minimum of 12 hours.  The main system components are as follows:
    Motherboard:  MSI K7N2 Delta ILSR
    CPU: AMD Athlon XP 2800+
    Memory: 2x512 OCZ PC3200 EL
    My problem is that the burn-in software continues to freeze up during the memory test.  I've already contacted the software manufacturers and the software is stable.  It's a problem with the way the motherboard handles the memory.  I've tried putting the memory in dual channel configuration and changing the timing settings in the BIOS.  The SPD settings are 2.5-3-3-7.  Right now I have them at 3-4-3-8.  It's a lot more stable than it was under the default settings but it still freezes up sometime after 7 hours.  Unfortunately, I wasn't around when it froze so I don't know exactly how long it lasted.  I can say that after 7 hours, it wasn't showing any slowdown in performance.  If anyone could think of anything else I might be able to do to get the system stable, I would greatly appreciate it.

    Thanks for the suggestions.  The CPU FSB is 200, so it's already matched up there.  And we have a ton of fans already.  There are two in the front, 4 inside and 1 on the back.  It's a custom case, 2u high.  The power supply is oversized and more than adequate to provide the required power.  I have four of these units running right now.  Two with 2x512 sticks and two with 1x1024 sticks.  For each combination, the memory clock speed for one is 166 and 200 for the other.  I have been loosening up the memory timings trying to get the system stable, but it still isn't.  If the power supply is good, and I'm unable to cool the system anymore due to limititions within the case, is there anything you can think of to stabilize the system.  Maybe other settings in the BIOS or suggestions on how to go about getting good timings for the memory.  Thanks.

  • MSI K7N2 Delta ILSR Bios v.7.6 ??When??

    Hello,
    I just asked myself when MSI is going to publish a new Bios Update above the 7.6 for the K7N2 Delta ILSR mainboard !!! I think it's time for a new Bios update, because of the few problems with this mainboard !!!!

    Quote
    He has confirmed the ports are present on the board....
    I have seen this in earlier Nf2 Pre Delta boards where it was there but if you had disabled it, and then flashed the BIOS, it would dissapear. The only way to get it back was to flash to an earlier version, make sure it is enabled, then you can flash to the latest.
    That is why I always clear the CMOS when starting a new build. You may have a board that may have been fiddled with, believe it or not, it does happen from time to time.
    Have you tried the Default BIOS Settings Option in the BIOS? Perhaps you loaded the Performance option and that is why it is hiding?
    this worked, thx a lot

  • MSI K7N2 Delta-ILSR Dead? Help!

    Hey all,
    Well, the other day I was on my computer playing a game when my mobo fan started making an odd noise (as if switching rpm), so I took off the side of my case and took a look inside. Everything seemed to be functioning properly, then I switched my cpu fan speed via the pci slot speed control. As I switched from High-Medium-Low, I noticed that the fan actually slowed to the point where I could see the blades spinning, at least for a second or so. I found that rather odd, seeing as how I've never seen a fan (especially a cpu fan) slow to the point that I could see the blades spin. Anyway, a couple of hours later, I shut down and went to sleep.
    The next day I had my comp on for about maybe 30mins to an hour or so when suddenly I heard an alarm from the computer speaker, so I was like, ":censored:?" since I had never heard it before. It was evidently the temperature warning, which I had set to 70C. So I shut down within 15 seconds and opened up the side of my case.
    I noticed that the cpu fan wasn't moving at all (usually I'd open the case in time to see the spin-down). So I turned the computer back on and the fan didn't budge, so I immediately powered down, assuming that the CPU Fan had died. Later on, I hooked the fan itself up to a free power cord in my sister's computer and booted up, along with the speed controller, flipping from medium to high to low without any problems.
    I then did screwed the fan back to the heatsink in my comp and booted up. I went into the bios an noticed that the rpm was 8k, which is way too high for my fan (normally 5k). So i began switching from high, medium, to low once again, then I saw that the rpm reader in the bios went to 0. So I looked back in the side of my case and saw that the cpu fan was once again dead. At this point I concluded that it was the fan and was about to order the Volcano 12.
    A day later I placed the fan inside my sister's computer on a free cord, yet again, and yet again, it worked fine.
    I once again put it in my computer to test and this time it worked fine, even while switching between speeds. Unfortunately, I then noticed that the mobo fan was not moving, then began to move.
    Well, I'm guessing now that it's simply the motherboard that has a short, since both the motherboard fan as well as the cpu fan have randomly been dying the past few days. The motherboard fan; however, has switched rpm many times in the past from 5k to 3k.
    It could also be a PSU problem, but I have Antec 400watt psu and it's been working fine for the past 2 years, so I doubt it. I've had the motherboard for a little over a year. I upgraded my cpu from 2200+ to 3000+ in July. That's also when I bought the cpu fan. The motherboard fan began fluctuating in rpm noticeably back in April or May of this year.
    Yesterday, I used the computer again and had it on for about 2 hours or so and I had speedfan monitoring the temps and the rpm. The temps stayed relatively stable: 48 cpu, 44 mobo.
    But alas, the RPMs were totally [blame me for the swear filter] up. At one point, both the mobo and cpu fan speeds were reading 0, even though both continued to spin within the case and the temps remained the same. Then after 30mins or so, they cpu fan began reading again at 40,000-42,000rpm, which is obviously incorrect, seeing as the fan is rated for around 5k. I got/get the same readings in the bios, both fans reading at 0rpm as they continue to physically spin.
    Also, during a number of times that I've started up the comp within the past few days, the motherboard northbridge fan wasn't spinning at all and didn't begin to until a few minutes into my windows session.
    Also, I took out the NB fan and noticed a slight crack in the back of it.
    I was considering simply just buying the Volcano 12 and the MSI K7N2 Delta2 Platinum rather than RMAing the mobo. Then perhaps an Antec 550W psu, if necessary.
    Any ideas what I should replace and in which order? And has anybody else encountered any similar problems with this mobo (at least with the mobo rpm, which has been a prob for about 6months on and off)?
    I bought the mobo along with a 2200+ in July of 2003. I upgraded the ram from 256 to 512 in April 2004 (which is around the time I started hearing rpm probs with the mobo fan) and I upgraded the cpu in July of 2004
    Many Thanks!  
    My Specs are as follows:
    Windows XP Professional SP1
    Antec SX1040B2 File Server Case
    400watt Antec PSU
    MSI K7N2 Delta-ILSR
    AMD Athlon XP 3000+ (2.17GHz)
    Thermaltake TR2 M2 HSF
    Kingston 256MB of PC2700 DDR-333MHz RAM
    Generic 256MB of PC2700 DDR-333MHz RAM
    ATI All-In-Wonder 9800 Pro
    Sound Blaster Audigy 2ZS Platinum
    Pioneer 10x DVD Drive
    Sony 8x Double Layer DVD-+RW
    Western Digital 120.0GB 7200RPM HD ATA/100
    Western Digital 120.0GB 7200RPM HD ATA/100
    nForce Ethernet Adapter w/Cable line
    Logitech MX500 Optical Mouse
    Logitech Elite Keyboard
    19" Envision Monitor EN985e
    Logitech Z-680 5.1 Speakers

    Could be a fluctuating PSU that's breaking down power to the MB. You have a whole lot of components dragging that PSU down. With what you have in your rig I would run either an Antec or Enermax 550W. Best way to be sure is to borrow a PSU or buy one from a store with a good return policy so that you can return it if indeed it turns out to be the MB. If I don't have your board here on my bench to test the only thing I can suggest to you is to swap out components unfortunately.

  • MSI K7N2 Delta-ILSR (MS-6570) BSOD problems grrr

    I recently purchased this board and although it is an awesome product, I'm having a problem with BSOD's when I play a game for a certain period of time
    Specs:
    MSI K7N2 Delta-ILSR  (7.6 BIOS)
    AMD Athlon XP 2800+ Barton
    512MB (2x256MB) Samsung PC-2700 DDR memory (2.5-3-3-6 1T)
    MSI 128MB GeForce4 Ti 4200 (4X AGP)
    NVIDIA nForce on-board sound
    Western Digital 80GB drive w/ 8MB cache
    MSI X48 CD/CD-RW/DVD combo drive
    Windows XP Professional SP1
    PSU:
    Turbolink 420watt (came with case)
    +3.3V is 28A
    +5V is 40A
    +12V is 18A
    So what happens is I get a STOP error during the game that shows the kmixer.sys driver as the culprit. Sometimes it's accompanied by PAGE_FAULT_IN_NON_PAGED_AREA too. I read somewhere that kmixer.sys has to do with windows audio and that it's a 3rd party driver issue or a memory issue. I'm using the latest NVIDIA 3.13 nForce platform drivers. I ran Memtest lastnight for 12 hours straight and 0 errors. I'm thinking the memory may not be compatible with the board nor dual channel, is this possible? I have also tried several different drivers for both video and chipset including MSI's own and I still get the kmixer.sys BSOD when playing games. My previous motherboard was an MSI KT3 Ultra2-R (MS-6380E) which I had no issues with. Any help would be greatly appreciated. Thank you in advance.
    --Update--
    I just tried to play a game with audio disabled and it crashed this time with DRIVER_IRQL_NOT_LESS_OR_EQUAL with nv4_mini.sys as the problem. My IRQ table shows some sharing, but device manager shows no conflicts.

    Ok I tried running the DTM-CB3 module which is nForce2 approved at 3-4-4-11 2T timings and experienced the same result even at 2.6 and 2.7v. I tried both in dual-channel and same thing happened. However, I downloaded a program called Prime95 and ran the CPU torture test and the system returned a fatal error within the first few minutes. CPU Temp was at 57 C and the warning beep (set to 60C though) sounded intermittentley which is strange. I let it cool down then ran the torture test again and about 5min. later the system either seized completely or the program crashed. IE has also crashed randomly on me. I did this several times, before trying a different FSB/DRAM ratio. So I left the system at 200 FSB and used a 6:5 ratio so my memory was running at DDR333 and processor was a 3200+. I ran Prime95 again and the system locked up just as it did the other times.  So after I did this a few times with consistent results. I went back and set the FSB to 166 and tried a 5:6 ratio so the memory was DDR400 and processor was the normal 2800+. I ran it again and to my suprise it passed all the tests and after an hour of this, I tried a game and that was perfectly fine as well. I checked the temps and CPU was only 45 C this time. So I'm thinking the processor can't handle anything above 50C or it's just plain overheating. I ordered a Thermaltake Silent Boost HSF today which is tested up to 3400+ so this should fix my problem. If not, then I'm going to replace the memory with a 512MB Geil PC3200 golden dragon dual-channel kit.

  • MSI K7N2 Delta-ILSR Wont boot up (no display no bios)

    Hi
    i bought a AMD Athlon XP 3200+ & MSI K7N2 Delta-ILSR.
    unfortuntly i can't boot it. it wont show anything on screen.
    i have tried anything i red in this forum (clear cmos... safe mode jumper...strip all parts...)
    all i get is : 
    blank black display, no beeps and keyboard lights flashes over and over (when connected to a KVM hub), when conected directly to keboard the lights flashes only once but stil black display and no beeps (i hear on speake,when powering up PSU, a silent short noise, no beep).
    power suply turns on (new one 500w), i tried agp video card and replaced with pci video card.
    memory is kingstone 512mb pc3200 400MHz x2, i tried only one of them and both in diferent sockets.
    cpu: AMD xp 3200+ 400fsb.
    i did succed to go into bios only once, after lots of resets and shutdowns and bios clear (after ouers)
    i choosed in the bios: load bios defaults, and thats it. i hoped it starts up but nothing.
    i did all testing i know (checked all pins, cables, clear cmos...all, you name it)
    all parts are brand new (except motherbord. it's seconds hand from eBay. i've bean talled that it works fine)
    i also e-mailed MSI support that question. (2 days ago. no answer yet)
    oh...and i have a pci POST diagnostic card and its 7seg display don't shows any numbers, only when once i succed to get into bios. i don't have the msi original D-Breket addon diag.
    can you help me? 

    hi guys
    here is my PSU specs:
    Colors-It 500w-Max Silent ATX Power Supply
    Voltage 115/230V
    Current 10A/5A
     Frequency 60/50Hz
    +3.3   +5    +12   -12     -5      +5SB   BLK    GRN    GRY
    30A    50A  15A   1.0A   1.0A   2.5A   COM   P-ON   PG
    connectors:
    ATX-2.03 Connector: 1
    ATX-12V Connector: 1
    CD-Rom/HD 4 Pin connector: 6
    Floppy 4 Pin Connector: 2
    Serial ATA Connector : 1
    cpu: AMD Athlon XP 3200+
    MotherBoard: MSI K7N2 Delta-ILSR   More: http://www.msicomputer.com/product/p_spec.asp?model=K7N2_Delta-ILSR&class=mb
    Memory: kingstone 512mb pc3200 400MHz x2      More: http://www.ec.kingston.com/ecom/configurator/PartsInfo.asp?ktcpartno=KVR400X64C3A/512
    i have other brand of memory moduls (micron pc2300) i tried them too. no go.
    i tried other PSU, i pulled from my brothers pc (amd xp 1400+).
    as i said before, i have  pci POST diagnostic card so it could tell me any problem. iguss it's the mobo, posibly bios upgrade.
    but if mobo not showing bios, i can't update bios from floppy.
    and the tested the mobo out side the case on a antistatic mat and i useed an antistatic strip.
    as i said i could get into the bios once, after many resets....choosed 'load bios defaults..', restarted and.....no go.

  • MSI K7N2 Delta ILSR and Serial ATA Drive

    I've got a very strange problem....
    Yesterday i have installed my new motherboard (MSI K7N2 Delta ILSR) but i have a problem with the SATA feature.
    I've got two drives : one 40GB ATA (Western Digital) and one 160GB SATA also from Western Digital.
    My SATA drive is recognized by the FastTrak BIOS (v2) but i'm unable to reinstall Windows XP Professional (with SP2 Slipstreamed) because Windows Setup didn't recognize the SATA disk. I have loaded the Promise Serial ATA Drivers at the begin of the installation (F6)...
    I have also tried 2 different versions of the Promise SATA Drivers; the one that cames with my motherboard CD, and the most recent from the MSI website. But with both drivers the same result. How can i get my Serial ATA Harddisk get work with this motherboard?
    Any help will be appreciated. 
    Thanks,
    Computerfreakje.
    PS : My specifications are the following:
    MSI K7N2 Delta ILSR (Rev. 7.4)
    AMD Athlon XP 2500+
    2x 256MB Kingston PC3200 Dual Channel
    ATI Radeon 9800 Pro 128mb (R360)
    Western Digital 40GB ATA
    Western Digital 160GB SATA

    Thanks for your reply Richard,
    My motherboard didn't came with a floppy (I have bought an bulk version..) I have created a SATA floppy by myself. (I have got the drivers from the motherboard cd..) These drivers are also good, right?
    Which type of RAID Array should i create? Because i have only one SATA drive.....
    I think the "auto" feature is the easiest way?
    Thanks.
    Computerfreakje.

  • MSI K7N2 Delta-ILSR and Mushkin

    Does anyone know if the MSI K7N2 Delta-ILSR has any issues with Mushkin ram. Specifically, with Mushkin PC3200 2-2-2? I previously had Mushkin PC2100 2-2-2 in it with no issues, but that was on a 266 FSB. On a 400 FSB, there may be issues. I dont know.

    I did a little troubleshooting on my own and learned some things. I borrowed my neighbors computer (athlon xp 2600+ (266) on an asus A7N8X-E Deluxe with 2 512 meg sticks of Mushkin PC2100 2-2-2 ram). This computer has a generic 300 watt power supply, so you have to take this into account after seeing the results. First I ran prime95 on his machine and it ran rock solid. I substituted my PC3200 memory in his machine, and first ran it at 266 with no errors. Then I bumped the memory up to 333 and I got an error after 1 hour 17 minutes. Then I bumped the memory up to 400 and couldnt get past 10 minutes without an error.
         I then put my proc and his memory in his computer, and my proc ran stable, and I didnt get any of the rebooting that I was getting in my machine. When I put my memory in his machine with my proc, I get about the same results as with his proc.
         When I put my proc in my machine with his PC2100 memory, I still got some rebooting. When I substituted my PC3200 memory in, I still got the rebooting.
         I then underclocked my processor down from 200 mhz bus to 191, and kept the ratio at 1:1 for memory, and still got some rebooting.
         I then changed the ratio to 6:5, so the bus is now 159. The timings are at 5-2-2-2. The computer is running very stable and goes through prime95 with no errors.
         I can put my proc and ram in my neighbors computer and get no rebooting, whereas in mine it wont stop rebooting when I have it set to spec. It looks like I have to change my mobo and/or my PSU. My PSU is an Enermax 431 watt and I have never heard of an Enermax going bad. That makes me suspect the mobo a little more, but I dont really know.
         I will continue to experiment with bus speeds, ratios, and timings to see if I can get any more out of this system. But at least it is running OK now.

  • K7N2 Delta ILSR blown?

    I have K7N2 Delta-ILSR.
    I wanted to use the dolby digital out put of the board and since I didnt have a S-Bracket I decided to hook a wire onto the pin and connect that to a rca cable which goes to my decoder.
    I used the board like this with no problems for about 10 months.  But then the wire got moved and I think the board got shorted so it shutdown. This happened once before but the pc was fine.. This time the pc wont boot. I checked all the components and everything seems to be working including the power supply. The fans spin for a few seconds then it stops.
    Whenever I plug in the power the Nforce 2 MCP-T gets really hot. you can barely touch it. So do you guys think I blew it for good and need a new board?

    i have this board and i have done plenty of stupid things with it, it alway's seemed to live on with no problems, except once i cant remeber clearly though.
    i did a ridiculus overclock from stable 199 to ~220 @ 1.8, tries to put it in safe mode nothing??, un hooked everthing and put it back together.. nothing, so i left it unplugged and without a battery for about two week, dident want to look at it as i though i f++ked it.
    came back to it, put most of it together and it booted no problems in safe mode, dont know what happened but its still living now?

  • K7N2 Delta-ILSR BSOD

    Hi
    MSI Nforce K7N2 Delta-ILSR
    Bios V1016
    Antec True380SPGB True Power 380w
    AMD Athlon XP2800+
    2x512mb Crucial DDR
    1xSATA HDD
    Abit Siluro GF4 Ti4200
    I've installed 1 SATA onto the onboard Raid controller, but I keep getting BSOD when either playing a game or watching avi's.  The 0x00000000 message is disappearing too quickly to right down but is saying windows was shut down to prevent damage to the hardware.
    Will the K7N2 Delta-ILSR Promise controller work with just one SATA hdd connected, I know that the silicon image controller on my Asus A7N8X-E will support just one SATA connected but will the promise chipset.
    I've updated all the drivers but the dreaded BSOD keeps happening.
    If it won't it not's a major problem as I do have a PCI sata controller card I can install.
    Or are there any issues with the above graphics card and the MSI mobo?
    Thanks for any help.

    Yep I've created a array with the single SATA and got Windows installed.
    I've also changed the memory settings so they are now 1:1 with the FSB.
    I've also altered the advance settings so I'll be able to write down the full 0X00000000 string.
    Just set net access up via my PC and got this error report from M$
    Error Message: STOP 0x000000EA THREAD_STUCK_IN_DEVICE_DRIVER (Q293078)
    Error Caused by Graphics Device Driver
    Thank you for submitting an error report. Microsoft is unable to determine what specifically caused the problem you reported. To troubleshoot the problem, please see the information listed below.
    Analysis
    A device driver installed on your computer caused the problem, but we cannot determine the precise cause. Depending on which situation is applicable to you, please do one of the following:
        * If you are running Windows Server 2003 you may experience crashes if you have adjusted the Hardware Acceleration setting. Microsoft recommends that you set the Hardware Acceleration setting to None for server systems. To check your Hardware Acceleration setting, go to the Advanced section of the display properties dialog box.
        * If you know the manufacturer of the device, contact the manufacturer's product support service for assistance.
        * If you don't know the driver's manufacturer and need help diagnosing and resolving this problem, contact your computer manufacturer's product support service.
        * Updated drivers might be available on the Microsoft Windows Update website. At Windows Update, you can have your computer scanned and, if there are updated drivers available, Windows Update will offer a selection of drivers that you might be able to use. To learn more about updated drivers that might be available, visit Microsoft Windows Update.
        * For information about Microsoft support options, visit Microsoft Product Support Services.
    I've downloaded the current graphics card drivers from Abit and I'll install them and see what happens.
    I've also adjusted the AGP in the bios from 64mb to 128mb.

Maybe you are looking for