K7N2 Delta-ILSR

I found the K7N2 Delta-L online at www.atacom.com
but im looking for the K7N2 Delta-ILSR anyone know where to find it?

I did an online search for them using all of my different sources that I use and I've not seen any as yet...sorry.
Cheers!! 8)

Similar Messages

Someone plz help me with my k7n2 delta-ilsr

Hey everyone,
I just put my sytem togother and ran into a problem. I got the system to boot up just fine. It was not until I tried installing windows xp proffesional that I ran into problems. The installation process runs pretty smoothly, until the computer reboots to run windows for the first time. After it reboots the windows logo appears and the after 2 seconds or so, a blue screen appears saying that windows was shut down to prevent any damage to my computer. I have never encountered this problem before when I built other systems. The screen suggests that I should check my HDD's for viruses or check to see if they are configured correctly. The HDD's are SATA and I have them set up in RAID 0 mode and yeah I installed the RAID drivers during the installation process. Thinking that I had made mistake setting up the SATA drives, tried installing windows using a regular IDE hard drive and it gave the same message. I am stumped anybody have any ideas of what I might be doing wrong? Any help would be appreciated . My system specs are below.
MSI k7n2 delta-ilsr mobo
AMD 3000+ Athlon XP cpu (333 fsb)
ATI Raedon 9000 ( I know it's crappy , I'm still saving up for the ATI all in wonder 9800 )
x1 kingston 512mb pc3200 DIMM
x2 maxtor 80gb maxtor hdd's
x1 regular cd-rom drive
x1 floppy drive
420w raidmax psu
(+3.3v = 26A, +5v = 32A, +12v=13A)

Memory that comes with timing of 5 2 2 2 or 6 2 2 2 or usally winbond BH-5 memory chips. Ones with 5 3 2 2 or CH-5 winbond chips. The BH-5 chips overclock a little better than the CH-5. (Muskin uses BH-5 winbond in there black ram)
Winbond is no longer making BH-5 chips but is going to make a limited run of them as demend is high for them.
The first number shown here is the Traz and it controls the flush timing bench testing is showing that a higher number of 9, 10 or 11 or getting better bench results than the 6 or 5. Thats with Dual Channel memory.
The timing you show probly should be something like 8 3 3 3 or 8 3 3 2.5 unless it is there faster Dual channel ram.
The timing numbers can also appear like this 2 2 2 5 the high number is the Traz either way.
Look on your memory manufactor web site for the timing that if should run at also look at the voltage as this can make a big differance.

HELP me with my K7N2 delta ilsr

Can anyone help me with this problem. I have just upgraded to MSI's K7N2 delta ilsr motherboard. Its all working quite well apart from the fact that the pc wont start up from cold....at all.
When I start the pc from an off state, it runs up the fans and drives, but does not post.
The diagnostic led pannel on the back of the pc shows that the cpu is faulty or not installed correctly.
If I then press the reset button, the pc posts, and boots up just fine.
It does this EVERY time I start up.
I have tried re installing the cpu, which is an XP 2800+ 333 barton, but to no avail.
I have asked a few questions on other forums, but I cant solve it.
These are the suggestions so far.
1. the psu (I have a Tsunami 400 atx psu) could not be giving out enough power on initial startup, but once the pc is running, it has enough to boot the pc from a reset.
2. The mobo or the bios could be at fault. I have not flashed the bios, or upgraded it in any way from original, so is there an issue with the original bios on these boards, and 2800 barton chips??? Could it be a mobo fault? The pc runs fine once the machine is booted.? how do I test it?
3. The cpu could be faulty? but would this not stop it running fuull stop?
4. my ram. I have a single stick of OCZ 512mb pc3200 ddr, which I was told would make the pc fly. Not shure on that statement, but is this ram compatible?? could this be the problem?
Im fairly new to the upgrade side of things, and I need some help with this one.
Also, Id be really greatfull if some one could talk me through flashing my bios to the latest version, as the thought of doing this narks me a bit...I dont want to mess it up and get a dead pc...
HELP

+3.3v 14A
+5v 28A
+12v 16A
+5vsb 2A
-5v 0.5A
-12v 0.8A
Hope this helps, as my pc seems to be living with its case off a lot these days..haha

Internet Connection Problem on MSI K7N2-Delta-ILSR

Hi, recently I buy an MSI K7N2-Delta-ILSR.I have a problem when I was trying to connect to the Internet through my modem on WinXP Pro SP1. It bring me up an error message 678 ( The computer that was tried to connect did not respond...). I have also a second hard disk with Mel windows. On disk the disk with the Mel I don’t have any problem with the internet connection. All my settings are same on WInXP pro and Mel.I have checked I thousand times. My computer configuration is:
Athlon XP 2400+ Overclocked to 2205MHz
2 memory modules of 256MB 400 manufactured by Samsung
TharmalTake Volcano 11
Triplex Xabre 400 PRO with 128MB
Hercules Gamesurrround Fortissimo III 7.1
Microcom InPorte Home modem 56k
Leadtek winfast 2000 (TV/FM radio)
Acard SCSI controller (Acard AEC-6710D) for my scanner
WesternDigital WD800 GB
WesternDigital 15.3gb
Bios ver.7.4
Can anyone help me?

Quote
Originally posted by Roger Wilco
Hmmmmm, I\'m also having a problem with the onboard lan of the K7N2 Delta.
I have an ADSL connection, and have an Alcatel SpeedTouch Home modem.
I pretty much get the same error as SiliconMan (The computer that was tried to connect did not respond...)
I ended up giving up on it for the time being, just using my SMC NIC. Would be quite interested in finding out what the problem is though.
Anyone else in the same boat?
Hi,
Your problem is not the same, SiliconMan is trying to connect with a dial-up modem not LAN. Your problem sounds like it may be configuration, do a search on this post, I'm sure you will find people with onboard LAN troubles. It's hard to troubleshoot though since you didn't provide any info about your computer. Good Luck
Rob

Strange phantom restarts on MSI K7N2 Delta ILSR

Just wanted to see if I could get opinions on this. My MSI K7N2 Delta ILSR mobo runs real nice now, but still, on occasion, very rare and intermittently, it will just restart. Not likely a heat issue, as the temps are nice and low. Also, not just happenning when I'm playing a game or anything strenuous. Did it once while checking email, once during install of an MS Office program, and once during a game. Could it be my old Gforce 2 MX 200 video card, as the picture sometimes gets wavy (like fine waves on an ocean), and the old computer it was in did similar things, or is it common with this mobo.
MSI K7N2 Delta ILSR
Athlon XP 2500+ Barton
1026 MB Kingston DDR RAM (2x512 Dual)
Gforce 2 MX 200 AGP 4x
WD 60 GB 7200 RPM

I had errors on test 4 not 5 with Winbond 2-512 Dual Channel called Hardcore Cooling and they said that getting errors with memtest86 may not mean that the ram is defective, it may not be compatible with the memory comtrol and they had me RMA it back. I also was not able to run the ram stable at there advertized rate of 6 2 2 2 it was only stable at 8 3 3 2.5
I replaced it with OCZ after talking to there Tech support people about compatiblety problems with the Nvidia chipset. Sense I installed the OCZ I only had one ram reboot and when I checked I was running the voltage at 2.5 and OCZ said that I should be running at 2.6. They also said that I could run it up to 2.8 with no worry.
Look on manufactor web site to see what ram timing yours should be running at and what voltage, Auto setting in Bios is not always the best setting.
If it still not stable at manufactor spec than I'd talk to who ever you bought it from about replacing it or refund and buy something thats on the Nvidia compatible list.
Most ram manufactors have a list of motherboards that there ram will work on but sometimes the newer boards like K7N2 or not listed yet as still working that out.

Kate needs HELP!!! MSI K7N2 Delta ILSR

Guys...
pls help me...
I am assembling, yes I know I am a techi girl...., msik7n2 with radeon9600 and 2xCorsair Value Select 256Mb DDR 400Mhz PC3200 mem...(hence 512mb)
I installed everything assembled it... booted and loaded fine for about 3 times...
and suddenly....
>power on
>no video
>no beeps
>after checking hard nothing happens...
>only thing I can tell is that the d bracket is indicating "memory section"
....d-bracket from MSI K7N2 Delta ILSR is 1,3,4 red and 2 green. Which is according the the manual "Memory Detection Test"-if the memory module is damaged or not installed properly.
Why woudl a memory suddenly not work?
I know I was adjusting bios for this and that....
I think just before this happened.. I adjusted something on agp setting... but what ahs that got to do with memory?
COuld it be the mobo or memory or the video card???
pls help....
My email is [email protected]...
please please help...
and guys in MSI what is your expert opinion? mobo? or memory?
Heeeeeeeeeeeeeeeellllp...
thanks...
Kate x

hi and welcome to this forum.
nice to se a girl here for a change
clear cmos jumper jbat1.
also try safe mode jumper j10 ans j11.
also try to reseat memory and dont trust the dbracket to 100%.
it can show wrong sometimes.
Quote
COuld it be the mobo or memory or the video card???
when you got it running then run http://www.memtest86.com to check memory,
also what psu do you have ?
post max amps on 3.3v 5v and 12v rails.
minimum is 28 35 16.recommended is higher.

Data corruption on MSI K7N2 Delta ILSR

Hi all,
Just got my new MSI K7N2 Delta ILSR up and running.
Got some issues with the memory running at 200mhz while the Barton core of my Athlon Xp 2600+ was running 166mhz, this had to be 1:1 (thx forum )
While running the default bios settings with cpu/mem at 166/166 fsb everything is stable as hell. I have been running Prime95 for 2 days now and using the system for dvd ripping/encoding, UT2004 gaming etc.
Then the overclocking began I'm using the standard AMD cooler that came with my boxed Xp2600+ so I didn't expect an FSB of 200mhz.
I stopped at an FSB of 190mhz...been crunching Prime95 for 18 hours now and again very stable.
Now comes the problem : Sometimes I get crc errors when installing a game or decrypting a dvd!! But how can this be? Prime95 is stable at this 190fsb overclock.
When using an FSB of 166mhz no data corruption or crc errors.
What can this be? It's not the cables because they're all the same as in my old setup which was running (ahum...walking) stable. PCI/AGP speeds are locked when overclocking...
Only thing I can think of is the power supply. I've read in a warning post from Bas that the Q-Tec 550w psu I have is crap. So my guess is PSU, but maybe it's something else I'm forgetting...Any suggestions??
The stupid thing is when I'm not overclocking I don't have the data corruption problems, but I'm still using the same crappy Q-Tec 550w PSU.
Help!
gr,
Remco

Hmmm, that's curious. On the MSI K7N2 Delta ILSR product page Kingston memory is recommended
Ok, did a Memtest86 v1.11 pass at cpu/dimm 166/166 - no problems whatsoever. I think using Prime95 would have revealed memory problems...but will do another pass with cpu/dimm at 190/190.
Can overclocking affect the Promise Raid Controller?? It should be locked like the PCI/AGP but who knows...
Well, I still have to replace my PSU but I'm not 100% sure that this is the problem. What PSU would you recommend? ...and I'm also thinking about replacing the standard CPU cooler, any advice is welcome
gr,
Remco

FLASH BIOS MSI K7N2 Delta-ILSR ????????

I am trying to flash the BIOS of my K7N2 Delta-ILSR board. I follwed all the instructions from the MSI Web but I can't get it going. I booted from Win ME & Win98 but could not get into C: drive. So I used Command Prompt from Window to get into the C: drive and follwed the Flash Bios Procedures. I keep getting the message: AwdFlash No Support WinNT/2000/XP OS
I got problem with the temp after I updated the BIOS. I wanted to flash it back to the old Bios. Please help me out
Thank you
My system:
WinXP Pro
MSI K7N2 Delta-ILSR
AMD 2500+
1 GB DR3200
Seagate 160 SATA

http://www.msi.com.tw/html/support/bios/note/ntfs.htm

PNY and MSI K7N2 Delta - ILSR

Looking into buying the K7N2 Delta-ILSR...I have heard that it is a awesome overclocker, and a very fast board. Has anyone had experience with using...
PNY Optima PC2700 DDR memory on it? It is double sided memory, with Hynix chips. Hynix chips are listed on MSI's Memory Compatibility PDF...but i wanted to know if anyone has used it before? Thanks

Its not tehre, but it does use Hynix chips, which IS supported. I also have read in this forum that people have got my exact memory to work flawlessly on the board i want. Thanks anyway!

Sudden Restarts MSI K7n2 DELTA ILSR

I've had this setup for about a year now.
Sudden restarts now plague my system, no virus found per NAV 2004, ran processor burn in wizard, SISOFT sandra, on cpu arithmetic and cpu multimedia setting, 100 cycles (no problems) windows memtest ran with no errors via start up disk full cycle of tests.
Have reloaded video drivers,to no avail, this happens about once a week, any ideas????
MSI k7n2 delta ILSR Bios version 7.7
1.5 Gig Micron PC 3200 (512x3) RAM supporting dual channel stock voltage
mixed bag o ram, crucial, micron technology, and, patriot
Athlon xp 2500 stock voltage
SLK 900A heatsink with 80 mm tornado (temps at idle 35-38c) (42 load)
Creative SB Live
Nvidia 256 mb asylum video card GE FORCE USR DATA PCI FAX Modem (V92) 5610b
Hercules 420W PS
All drivers are up to date and windows update run regularly (Win XP Pro SP2)
[/COLOR]

Quote
Originally posted by scooter787b
well for one thing the k7n2 series can only support 2 pc3200 dimms,
are you really sure ?
my motherboard which is rather old now supports 3 pc3200 dimms.
norton antivirus is CRAP.
i stopped using it when i found my harddrive was full of viruses.
try avg6 for example which is free.

MSI K8T Neo2 F vs. MSI K7N2 Delta ILSR

Hi there !
I have an amd Athlon XP 3200+ overheating problem, and contacted the technical support of the shop where the processor and CPU was coming from.
Since they do not have any XP 3200+ to replace mine, they propose me to replace fro free :
- the XP 3200+ by an AMD Athlon 64 3200+
- my actual MSI K7N2 delta ILSR by an MSI K8T Neo2 F
... and this for free.
Since I do not know this new motherboard that has been proposed, I'd like to have advice on if this is a good deal ?!?
My actual system has :
- an Aluminium case with 2x 12cm FAN's
- 2 IDE hard drives
- 1 SATA hard drive
- TWINX Corsair XMS 2x256MB PC 3200L (Extreme low latency)
- an AGP 8x video card
- An Antec True Power 480W.
will the new motherboard fit with this configuration?
Many thanks for your input !

Not really, unless you really want to oc your cpu. The K8T boards aren't that good in OC-ing. But still, some is possible and you'll be sure that the board is as steady as a rock.
For a moment I thought you were talking about a Neo board ... but I just saw it's a Neo2. That means Socket 939 -> dual channel RAM.
The only risk you have now, is that your RAM won't work in dual channel with the CPU. But that's not really a board-problem, more a CPU/RAM-controller related problem. But then, it's still a great offer and chances are good that it will work. If you run into any trouble, RAM-related, just flash bios to version 1.9 and you will probably be just fine.

Msi k7n2 delta ilsr problem

hi i have this configuration on my pc:
antec true control 550 watts
msi k7n2 delta ilsr
kingston hyper x pc3700 2x512 mb
athlon xp 3200+
seagate 120 gb sata 7200.7 hd
ati radeon 9800 pro excalibur ice q
i have 2 problems : the first one is that sometimes windows display me a blue screen with certain problem related to ati2dg.dll i think that problem is beacause the video card so i decided to update the bios , in the live update page from msi says that the bios 7.6 fix a bug with ati vga cards but after flashing and updating to bios v7.6 that blue screen with the same error still appearing so i dont know what else to do to solve the problem and the second one is that when i start any game or make the processor to work a little mostly related with video stuff the case speaker start to beep and the pc lags until he restarts with no reason i really dont know why if u can help me thank you

Foxtrotccs,
In the BIOS try setting the AGP to 4X and disable Sidebanding. Then set the AGP Apeture to 256. See if that helps.
Make sure you are running the lastest nVidia nForce Drivers and the latest ATI Catalyst Drivers
Take Care,
Richard
P.S. There is still a possibility that the Kingston RAM is the problem.

MSI K7N2 Delta ILSR Memory problems

I'm trying to burn in a system in a 50 deg C (122 deg F) room for a minimum of 12 hours. The main system components are as follows:
Motherboard: MSI K7N2 Delta ILSR
CPU: AMD Athlon XP 2800+
Memory: 2x512 OCZ PC3200 EL
My problem is that the burn-in software continues to freeze up during the memory test. I've already contacted the software manufacturers and the software is stable. It's a problem with the way the motherboard handles the memory. I've tried putting the memory in dual channel configuration and changing the timing settings in the BIOS. The SPD settings are 2.5-3-3-7. Right now I have them at 3-4-3-8. It's a lot more stable than it was under the default settings but it still freezes up sometime after 7 hours. Unfortunately, I wasn't around when it froze so I don't know exactly how long it lasted. I can say that after 7 hours, it wasn't showing any slowdown in performance. If anyone could think of anything else I might be able to do to get the system stable, I would greatly appreciate it.

Thanks for the suggestions. The CPU FSB is 200, so it's already matched up there. And we have a ton of fans already. There are two in the front, 4 inside and 1 on the back. It's a custom case, 2u high. The power supply is oversized and more than adequate to provide the required power. I have four of these units running right now. Two with 2x512 sticks and two with 1x1024 sticks. For each combination, the memory clock speed for one is 166 and 200 for the other. I have been loosening up the memory timings trying to get the system stable, but it still isn't. If the power supply is good, and I'm unable to cool the system anymore due to limititions within the case, is there anything you can think of to stabilize the system. Maybe other settings in the BIOS or suggestions on how to go about getting good timings for the memory. Thanks.

MSI K7N2 Delta ILSR - RAID BIOS Option ???

hi ho,
i have my 2 storage devices pluged into the promise 376 onboard controller. they are not connected as a real raid (not mirror nor real stripe). my OS is win2k on the first sata device and everything was fine for a long time.
but now when my system boots, it detects the ide drives and then i see the irq board.
right after that the system stops and tells me 'disk boot failure'. so i don`t get the chance to configure my raidcontroller or my sata devices.
it is as the controller is deactivated. i remember a bios version where you could activate and deactivate the sata controller. but in my bios (right now it is v7.8) there is no such option.
i have tested so far:
- reset cmos
- flash bios v7.5 to 7.8
- disconnected sata drives
anyone with similar problems or any suggestion?
> MoBo : K7N2 Delta-ILSR Bios v7.8
> CPU : AMD Barton 2500+ (not overclocked)
> Ram : TwinMos 1GB 3200 400Mhz
> Sata : 2 x Maxtor 120GB Sata (as single Devices on Raid-Controller)
> Ide : 60GB IBM DeckStar
> Gra : ATI 9600 pro 128MB
> Aud : SB Audigy 2 ZS
> Pow : SilverPower 350W, +3,3V/+5V@25A and 12V@18A
> OS : win 2000 SP4 + Security Updates 31.07.04 + DirectX 9.0c

watch the bottom of the screen after pressing Enter on the "Welcome to Setup" screen. There will be some moments of files being loaded, and then you should see a message appear which says "Press F6 if you need to install a 3rd party SCSI or RAID driver". This message will only stay on the screen for a couple of seconds, so press F6 as soon as you see it appear. After this is done, you will see other messages appear, and it will act as though nothing is happening, but eventually a screen will appear which will allow you to install the drivers for the sata controller.
specify a device press S, select "win 2000 promise fasttrak 376 controller" it will read floppy and load, dot not remove floppy yet, continue win2000 install it may nead to access floppy to finish installing raid driver, did you do it like this.
try making some floppy boot disks and boot to floppy instead of cd.
http://freepctech.com/pc/002/files010.shtml
when you say there not listed, where did you see this? they wont be listed, windows will search for fasttrak controller so it will see sata's conected to it with out you knowing, so long as you load the controller from floppy that came with mobo as above.

MSI K7N2 Delta-ILSR Noisy Northbridge fan

Hi
I'm having a problem with the nforce chipset fan on my K7N2 Delta-ILSR.
It makes a horrible wailing sound when cold booting and is only running at about 2500rpm instead of 4000rpm.
It does this usually for about 30 seconds then runs normally.
Does it just need cleaning or is it on it's way out?
Any help would be greatly appreciated.
Thanks
Garfy

Quote
Originally posted by Garfield
Hi
I'm having a problem with the nforce chipset fan on my K7N2 Delta-ILSR.
It makes a horrible wailing sound when cold booting and is only running at about 2500rpm instead of 4000rpm.
It does this usually for about 30 seconds then runs normally.
Does it just need cleaning or is it on it's way out?
Any help would be greatly appreciated.
Thanks
Garfy
Hi,
I had the same problem. All I did was loosened the left screw(when looking from the front of the case) until the noise stopped. Give it a try!!!

MSI K7N2 Delta ILSR Bios v.7.6 ??When??

Hello,
I just asked myself when MSI is going to publish a new Bios Update above the 7.6 for the K7N2 Delta ILSR mainboard !!! I think it's time for a new Bios update, because of the few problems with this mainboard !!!!

Quote
He has confirmed the ports are present on the board....
I have seen this in earlier Nf2 Pre Delta boards where it was there but if you had disabled it, and then flashed the BIOS, it would dissapear. The only way to get it back was to flash to an earlier version, make sure it is enabled, then you can flash to the latest.
That is why I always clear the CMOS when starting a new build. You may have a board that may have been fiddled with, believe it or not, it does happen from time to time.
Have you tried the Default BIOS Settings Option in the BIOS? Perhaps you loaded the Performance option and that is why it is hiding?
this worked, thx a lot

K7N2 Delta-ILSR

Similar Messages

Maybe you are looking for