K7n2 delta l boot screen

i looked at other companies' similar nforce2 ultra400 mobo and found out that most of them have boot logo but mine doesn't have. even k7n2g has the feature. why doesn't k7n2 delta? i've search the bios (latest) for the corresponding setting but with no avail. tell me how to enable it!
amd athlon 2500+ barton
msi k7n2 delta l
nvidia tnt2 m64 (my friend's. will get radeon 9600xt later)
256MB

Hi,
Am I the only person round here to consider this a non-issue? This is the second time I've seen a thread about this in the last couple of weeks!
As far as I'm concerned the MSI "Splash" screen is nothing but an advert for MSI. Most of us at some time or another, complain when we're forced by advertisers to view their latest ads, whether it's on billboards, TV, magazines or elsewhere! But not it seems, in this case!
If it was something worth looking at - like a nice young lady or an Ansel Adams landscape then fine - but the MSI logo - no thanks!
The minute I saw the MSI splash, I immediately went looking for the option to switch it off, and it's been like that ever since! (the small logo option too). I for one would rather see what is happening on the initial bootscreen!
Then again, when I do boot I don't usually hang around to watch it - it takes so long I can be doing other (more important) things!
Am I missing something here? Because I can't for the life of me figure out why this could possibly important to anyone?! It just sits there for a few seconds then disappears!
Quote
i want to have somthing nice during bootup to show to my friends
Eh???
I'm sorry friend but your gonna have to give MSI more reason to spring into action than this!
Quote
is msi going to develop a feature like personalizing bootup logo?
many companies have that now.
Actually, you've been able to do this with many motherboards for a good few years now, but I don't think it's at the top of MSI's priority list!
But.....who cares??
Axel

Similar Messages

K7N2 Delta not booting

My K7N2 Delta was working fine. Then it start emitting an aduible alarm. I turned of the machine, and it happened again. Now it will not boot. My screen is dead. My D-Bracket lamp shows CPU failure but I have swapped the CPUs. Still no joy. ;( I have cleared the CMOS, no joy. What next ?

uphaze,
If your heatsink and fan hooked up correctly?
Take Care,
Richard

K7n2 delta wont boot

i need some help please guy s, ive just built a system with these specs
k7n2 delta
barton 2500
kingston ram 2700 2x 256
80g 7200 2m cache hdd
gforce 4 mx4000 msi
350w psu
after building and trying to boot it getts to the "initialize floppy drive controller" signal on the d bracket (the floppy also does the green light and scanning noise thing) and the system and d bracket lights hang there, it wont go any further. any ideas guy s? is the mobo D.O.A ?
really need the help so any is very appreciated thx

thx alot, i really hope you fix it i know how it is :s.
ok update guys im running a cd rom on 1 ide (in master) and then the hdd on anouther ide (also master) so i unplugged the cdrom and ran just the hdd in master, that got me to the boot screen (i.e the hit del to get into bios screen). i get this msg
primary master = none
primary slave = none
secondary master = h
secondary slave = none
secondary master hard disk fail
i think its a hitatchi hdd so is it not seeing it properly and therefore only writing the first letter hense the H ?
? does this mean my hdd is incompatibly or broken or what ?
once agian any help is good thx guys
in reply to above they seem ok to me cant see a prob there as theres only one way the ide cables will go in on the new rounded ones. :s

MSI K7N2 Delta-ILSR Wont boot up (no display no bios)

Hi
i bought a AMD Athlon XP 3200+ & MSI K7N2 Delta-ILSR.
unfortuntly i can't boot it. it wont show anything on screen.
i have tried anything i red in this forum (clear cmos... safe mode jumper...strip all parts...)
all i get is :
blank black display, no beeps and keyboard lights flashes over and over (when connected to a KVM hub), when conected directly to keboard the lights flashes only once but stil black display and no beeps (i hear on speake,when powering up PSU, a silent short noise, no beep).
power suply turns on (new one 500w), i tried agp video card and replaced with pci video card.
memory is kingstone 512mb pc3200 400MHz x2, i tried only one of them and both in diferent sockets.
cpu: AMD xp 3200+ 400fsb.
i did succed to go into bios only once, after lots of resets and shutdowns and bios clear (after ouers)
i choosed in the bios: load bios defaults, and thats it. i hoped it starts up but nothing.
i did all testing i know (checked all pins, cables, clear cmos...all, you name it)
all parts are brand new (except motherbord. it's seconds hand from eBay. i've bean talled that it works fine)
i also e-mailed MSI support that question. (2 days ago. no answer yet)
oh...and i have a pci POST diagnostic card and its 7seg display don't shows any numbers, only when once i succed to get into bios. i don't have the msi original D-Breket addon diag.
can you help me?

hi guys
here is my PSU specs:
Colors-It 500w-Max Silent ATX Power Supply
Voltage 115/230V
Current 10A/5A
Frequency 60/50Hz
+3.3 +5 +12 -12 -5 +5SB BLK GRN GRY
30A 50A 15A 1.0A 1.0A 2.5A COM P-ON PG
connectors:
ATX-2.03 Connector: 1
ATX-12V Connector: 1
CD-Rom/HD 4 Pin connector: 6
Floppy 4 Pin Connector: 2
Serial ATA Connector : 1
cpu: AMD Athlon XP 3200+
MotherBoard: MSI K7N2 Delta-ILSR More: http://www.msicomputer.com/product/p_spec.asp?model=K7N2_Delta-ILSR&class=mb
Memory: kingstone 512mb pc3200 400MHz x2 More: http://www.ec.kingston.com/ecom/configurator/PartsInfo.asp?ktcpartno=KVR400X64C3A/512
i have other brand of memory moduls (micron pc2300) i tried them too. no go.
i tried other PSU, i pulled from my brothers pc (amd xp 1400+).
as i said before, i have pci POST diagnostic card so it could tell me any problem. iguss it's the mobo, posibly bios upgrade.
but if mobo not showing bios, i can't update bios from floppy.
and the tested the mobo out side the case on a antistatic mat and i useed an antistatic strip.
as i said i could get into the bios once, after many resets....choosed 'load bios defaults..', restarted and.....no go.

K7N2 Delta ILSR Takes forever to boot.

Specs:
K7N2 Delta ILSR Mobo
Athlon xp 2500
Kingston Hyper X 2700 DDR 512mb (its on the list)
Geforce 2MX 32mb AGP videocard (I dont play games)
3 Com 56k Win Modem
IBM GXP120 60 gig ata133 Hard drive
Pine 12X DVD drive
LG 24x10x48 CD Burner
Antec 300W power supply
The problem is that it takes forever to install and boot windows with faster processors for some reason. I origianlly built this system with my old Athlon 1.33 and it had these problems. I then tried a 900mhz athlon and it worked great, so I figured I damaged my 1.33 somehow. I ordered a 2500+ and a zalmann cpu cooler and now am back to where I was, when the system starts it seems very unstable and the screen goes blank for 10 minutes while its booting. It shows about 3 seconds of the starting windows screen then the screen will go blank for a while anf there will be no hard drive activity then it will come back about 10 minutes later and then boot. Sometimes the system will work fine then sometimes I cant even open my computer i just get the searching flashlight icon where my drives should be. I have updated to the lastet BIOS. Also while installing windows I get ocasional long pauses where it is doing nothing at all then it will just magically conitnue and do it in a fashion I would expect a machine of this speed to do.

Hmm not sure about the cable position on the CD drives, ill have to check that when I get home. All the jumpers are set correcly, and the hard drive is all by itself and its on the right connector. Thanks for the ideas, this problem is really killing me, I havent had these kind of hardware problems in years. The thing I dont get is why it works good with the 900mhz and not with the 1.33 or 2500+

K7N2 Delta-L: Strange cold boot problem & solution

My K7N2 Delta-L has a problem cold booting when the vcore is set in the bios at 1.65v of higher. After a cold boot, you get a blank black screen. I noticed that even if you run at default speeds but set the vcore to 1.65v of higher the problem still occurs. There is no problem rebooting however.
I found the following solutions:
1. After you power up and get a blank, hit the reset button.
2. Don't unplug your PC. My PC is connected to a AVR and after I power down the PC I usually turn the AVR off. If i do this, than the computer will have a booting problem if I try to boot it up 30 minutes later or so. Now if I don't unplug it/power off the AVR than everything is fine.
I don't understand why it acts the way it does though.
Does anyone know of any other solutions?

Have you cleared the cmos. If you do be sure you have the power turned off don't move the cmos jumper with the power on.
I found that turning off power at power supply and unpluging, than turning on the computer the fans will spin just a little this drains all the power. Clear cmos 2-3 than return to
1-2 position.
Than plug the power back in and turn it back on, than try the computer again.

HD or Booting problem on MSI K7N2 Delta 2 Platinum

Hi all,
Ive a weird issue which i cant figure out myself. I've 2 HD's..lets call them A and B where A = 60Gb (Master) and B = 80Gb (Slave)
It's is like this:
A and B are connected to the primary IDE-slot. A will boot when set as Master and B wont start booting when set as Slave mode (i mean, it wont show/appear in the first hardware (detection) bootscreen of yer BIOS where it says its present or the so called POST-screen), but if I set B as Master only (A turned off) it will boot.
What also happens is if I disconnect the power of drive B..drive A will boot..and while OS is loaded...I turn on the powercable from drive B and reboot..suddenly out of the blue it detects both HD's and reboots like it should do normally...but when i reboot from than..the same thing happens again..(it wont recognize B anymore)
Sumtime it regonizes both drives and sumtime it just won't and sumtimes just 1 drive..
Another thing, when it won't recognize one or sumtime both drives...the POST-screen gets stuck at the name and version of the BIOS...and where it says: 'detecting IDE drives...' when it is at this stage..and I press on the DEL-key for example..it's loading damn too slow..I've to wait about 10min before it enters the BIOS-setup..
I am 100% sure I set the jumper correctly for Master or Slave mode on my HD..I know there's sumthing wrong..but don't know where...Ive changed the jumper with a new one ..switched IDE-cables...switched HD's (set B as Master and A as Slave and vice versa, knowing there is no active partition on B..but only to check if it recognizes the drive)..in all cases..the BIOS settings are set as default!
any1 can help me out with this?
It worked smoothly on my system till i noticed my second MEM bank of my mobo broke (Asus A7N8X-E)..so i had to change it quickly (and went to the store with my warranty to fix this board..it was only 3 months old) ..since I've seen/had enough Asus mobo's in my life I went this time for an MSI which looks better in my opinion...so now i have an MSI K7N2 Delta 2 Platinum..it works fine...except that HD issue mentioned above
any help would be appreciated..thnx in advance!
cheers!

Hi,
I've done that already several times...it doesnt work..any other suggestions?
Now I can boot normally when I disconnect the power of the 2nd HD (or just any HD)...when the os is loaded...I turn back on the power of the 2nd drive and reboot...than it will run/boot/restart etc..normally...this is the only workaround I have at the moment...this only works when the system is turned a long time...
My power supply is 400W..so I don't think Ive any prob with that
cheers

K7N2 Delta ILSR won't boot from FDD or HD

I have a serious problem with my new K7N2 delta ILSR based computer.
My machine is
K7N2 delta ILSR 400W
3.3/25 5/32 12/15 V/A PSU
512+256 MB A-data 3200 ram
Athlon XP2500+
BTC 48x24x48 Combo
100 mb Zip int. -disabled
120 GB Seagate barracuda SATA-disabled
120 GB Seagate Barracuda parallel
Triplex parasouls ATI 9600PRO 128MB
The machine POST's normally with all 4 lights doing what they should.
The Promise BIOS can detect the SATA drive correctly but when an attempt is made to write the array an error- 'error modifying array- system is going to reboot- press any key to reboot>" is given.
The M/B BIOS detects the FDD and Seagate Parallel drives correctly but when a correctly formatted XP boot disc (or Mandrake Linux or Caldera DR-DOS) is placed in the floppy drive a "no system disk" error is given.
When you F6 to install RAID drivers in the Windows XP install and the screen comes up where you are prompted to insert the floppy there is no mass storage device detected.
I purchased a new FDD and it gives precisely the same error as the original.
I installed the parallel Seagate in another system and installed and activated windows XP on it. After re-installing it in the K7N2 system I was disappointed to discover that it will not boot off the hard drive. When you boot from the XP CD the machine locks up. (Disconnecting the HD it will boot normally)
This is a real puzzle as it is possible to format the hard drive using Max Blast3- the maxtor disk utility which is based ( as is the Seagate Seatools utility) on Caldera DR-DOS). And I can't see why it should boot from a CD-ROM and not from any other correctly formatted boot disk.
I suspect a problem in either the (South?) bridge that controls the peripherals or the BIOS. I am at a loss how to re-flash the BIOS with out the use of the floppy drive- unless this can be done from a CD-ROM.
The PSU is not being strained and nForce list both RAM sticks as OK.

Quote
Originally posted by Wonkanoby
is the fd light on all the time,as that means the ide type lead needs flipping 180 degrees in the back of it
is the hard drive ide 80 wire ,blue end in the board
any thing shorting under the board,an extra stand off or the like
The Fd light behaves normally. i.e. lights up when the drive is being accessed.
has anybody else noted that the FDD is B by default- That the cables have a few wires twisted like the wires between the first and second plugs on the old cables?
The IDE 80 wire(counted!) is long end in the board- my plugs are all 3 black. You can't put them in the wrong way becaue of the centre key.
All the stands are plastic except for two brass ones that are in the centre of the board that go to circular mount pads. That is how the case came and I thought it was a design feature.
The thing I find most puzzleing is that i can boot a caldera based system that finds everything including the floppy- and read it- (provided you call it drive B!) yet naything DOS based won't go- I have this feeling that it has a screwed up DOS call that is not looking in the right disk sector for NTldr or whatever to boot. I think this is a bios problem- but I am not sure how to find out when you can't boot from the FDD.
My brother has talked to some tech friends and there word is that this is a weird one- probably a dud board RTS.

Boot problems with IDE HD and SATA HD on K7N2-Delta L

I'll get right to the point.
I have an PCI SATA Controller Card in my system (using a K7N2 Delta-L motherboard, BIOS v5.7 with an Athlon XP 2800+ and Corsair ValueSelect 512MB DDR400 RAM on a single stick). My system works fine in it's original configuration of drives (CD-RW drive only drive on IDE bus, and SATA drive only hard drive). However, upon installing my IDE hard drive from my old computer, the system will no longer boot right. I am connecting the other IDE HD as Slave on the CD-RW's bus, as I'm reserving the second bus for bigger and better things such as a DVD burner, and speed isn't too important for this hard drive as it's just my MP3/data I don't need in a hurry drive.
In the current configuration, all three drives are detected properly (CD-RW and HD detected on the IDE detection screen, and the SATA drive detected on the SATA card's detection screen). However, after the SATA detection screen, the system just stops. The cursor is still blinking, but nothing comes up.
Both hard drives are Western Digitals (IDE is a ATA100 Western Digital 60GB at 5400 RPM, and the SATA is a Western Digital 36.7GB at 10,000 RPM), and the CD-RW is a HP CD-Writer 9100. I have Windows XP installed on both hard drives (first partition of the IDE, which is divided into two), but considering the system doesn't even attempt to boot I don't think that's an issue. I've gone through and tried enabling and disabling "Boot Other Device", but still no love. My boot order is set to Floppy, CD-ROM, and SCSI, which works fine when the SATA drive is in there.
Any idea what's up? I can provide more information upon request, as I'm sure there's something I forgot to mention that's important.
Thanks.

Take a look at this link, https://forum-en.msi.com/index.php?threadid=71384, I think you both have the same problem. It seems that a sata drive doesn't like having an ide drive in the system that has an active partition.
Do like Wonkanoby suggest, reformat the ide hard drive and make sure that it's not set to be the active partition in the system. Boot with a 98 boot floppy if you have to so you can format the ide drive to fat32, once you can boot up using the sata drive you can use xp disk manager to convert the ide drive to ntfs.

Fatal Exception on boot with K7N2 Delta-ILSR

Ok, my roommate just got a new K7N2 Delta-ILSR. We got it hooked up and as soon as it got to the windows boot screen, a fatal exception error popped up. We reinstalled the OS (Windows XP Pro), and it goes through the drive format and copies the files just fine. But when it reboots it pops up the fatal exception error again. We've tried restarting it, and it will go through the rest of the installation, then give the error on the next boot. After this it won't go past the OS boot. I've checked all the cables and jumpers, everything looks good there. We've checked the powersupply, and it is a little lower than what I've seen people suggest here, however it's higher than mine, and I'm running a K7N2 Delta-L.
As for memory, he is using Corsair Dual Channel PC 2700. We're going to swap the power supply and the RAM to see if that makes a difference, but I wanted to know if there was anything else that might cause this problem.

Ok, we've found a temporary solution to the problem, but it's not one that sits well with my roommate. We've underclocked the ram down to 266mhz instead of 333mhz and we have it running in single channel mode instead of dual channel. The system runs ok, and it's only locked once while playing Planetside, but that was about 5 hours into the game and I think it was because of a bug in the game. If that's the permanent solution, then he'll probably be returning either the ram or the motherboard, depending on which one is having the problem.
And as much as I love MSI products, I do have to say that I am very disapointed with their technical support. I mean, honestly, it's pretty lame when you can't call on a friday to get support. I can understand not being open on saturday and sunday, but to have nobody in the office on a friday is just insulting.
Anyways, still looking for a solution to get the ram and the motherboard to work together at the normal clock speeds.

[nForce] K7N2 Delta 2 LSR boot/power up issues

I installed the K7N2 Delta LSR mb with an Athlon XP socket A 3000+ cpu. The computer turns on but won't boot. Nothing appears on the monitor screen and there are no beeps. The harddrive spins, the board has power but nothing happens. When I put my old mother board back (MSI K7T Pro266A) in with the Athlon 2000+, everything works fine.
Maxtor 60 gb harddrive
512 MB SD pc2100 SD Ram
Abit 128 mb Radeon 9200SE Video card
Any suggestions?

A few things to check:
Do you have any unused stand offs in the case touching the motherboard
The XP3000 CPU is a barton core and comes in two variants, a 333FSB and a 400FSB version. Your RAM is PC2100 which with an Nforce chipset is a recipie for problems. The NForce chipset is picky about RAM and PC2100 running on a PC2700/PC3200 processor FSB probably won't work.
Also post your PSU max amps, as a +12V rail below 16A could cause problems.
Do you have a D-Bracket connected ? This is the PCI insert with 4 leds on ?

K7N2 Delta restarts when I boot

CPU - Athlon 2800XP
MB - K7N2 Delta
RAM - Corsair CMX512
Video - ATI Radeon 9700 Pro
OS - Windows XP
When i boot, it brings me to the windows screen where it gives me serveral options like : Boot normally, Restore to last config, boot in safe mode, etc. Then when i choose any of those, it just restarts. It never lets me into windows, it just restarts.

yep its gone UNLESS you put your HD back in your old system and then transfer what you want over to another harddrive. You should always partition your HD and store what you want on 1 partition that you do not want to lose and put your OS on the other partition

Duel boot K7N2 Delta using SATA and EIDE

I have a K7N2 Delta MB with SATA running RAID 0, also I have HD pluged into the Primary EIDE cable slot, using SC ( cable select ), everything works fine. What I want to know is if anyone has had any luck using BOOT MAGIC (comes with Patition magic) to duel boot between the SATA and the EIDE drive. Also I have found that once I set the SATA to be bootable AND loaded XP then I was not able to boot from any other device, floppy or EIDE. The floppy works fine when I use it once running on XP. I have the floppy set as the first boot device the EIDE drive c: as second boot device and SCSI as third boot device, the system always boots from SCSI. Any suggestions out there great ones?
Never mind I found the answer.
I took off SCSI from the 1st, 2nd and 3rd boot. enable other boot and all works fine now.

Wonkanoby, You are now officially my hero. Did exactly what you said. IT WORKED. My system screams now. Thanks.
p.s. Have you ever thought about rewriting the manual for MSI. Their documentation was confusing at best.
p.p.s Saw the other reply below about reflashing the bios. I see no need to do that. follow the instructions in the first reply and you should be good to go.

Argh! K7N2-Delta ILSR hangs at boot attempt

I built a new system today, everything right out of the box (except the HDs):
K7N2-Delta ILSR
Athlon FX 2500+ w/factory cooler
Kingston KVR333X64C25/512
Sapphire Radeon 9100 Atlantis
Western Digital 60GB
Western Digital 80GB
Pioneer DVR106
Antec Sonata case, 380W
After bolting it all together, the D bracket shows that the system hangs at 'Boot Attempt' (upper left LED red, others green). I've taken it apart and reassembled it, checked all the drive jumpers, reseated cables, etc. Cleared the CMOS and reset the jumper. Moved the memory to all three slots, no change.
When I turn it on, the drives spin up, fans come on, and everything seems OK. Still, nothing.
Any suggestions before I start the percussive maintenance on it?
Thanks!
-bruce

them models should be ok the bb you need to butcher the ide
https://forum-en.msi.com/index.php?threadid=1438&sid=
>Thanks. Read it and think I am on track. Checked my specs and was surprised the the 80GB is 7200rpm.
check jumpers there pin 4 is slave and i assume it an 80 wire ide blue end in board
>Right on both. Still, I am trying to boot with just one (have only tried the 60GB).
and in top one of 3 ide slots as lower is the raid one and it will not work as a regular ide nor in raid with 2x drives
>Spot on: cable's connected to the middle of the three IDE slots. DVD is on IDE 2, but I think I will disconnect and use my trusty CD-ROM until I get up and running.
myself i use all my wd drives in cable select
>Thanks, will try that too. I am at work, so will have to wait until I get home this afternoon to try your suggestions. Thanks again!

Band new computer with k7n2 delta will not boot or moniter not working

this is my first complete system build so please bare with me. the system uses a enlight 420 watt power supply in a lan boy case. it has a K7N2 Delta mother board with a 2500 barton amd cpu. the drives include 2 cd drives 1 floppy and one 120g hd, pny 5600 ultra video card 1 g kingston value ram ddr dual channel. when i turn on the power all the fan turn on the led in the front of the case light up but i get no boot or or video card not sure which yet. i get #1 led is red #2 led is red #3 led is green #4 led is green. i has tried to unplug drives with no change. tried a cmos reset with no change. tried a old voodoo video card with no change. tried to set the fsb to 100mhz with no change.
any other idea or suggestions would be helpfull.
justin
just tried used one stick of ram at a time with no change. the p.s. is +5v 40a, 3.3v 30a, +12v 18a, -5v .3a, -12v .8a, +5vsb 2a.

GOT IT TO POST LAST NIGHT. I HATE TO SAY WHAT I FOUND I FEEL A BIT LIKE AN IDIOT. WHAT I FOUND WAS THAT THE RESET BUTTON IS POLORIZED AND I HAD IT ON BACK WORDS. I TOOK ME WALKING AWAY FROM IT FOR A DAY TO COME UP WITH THE IDEA.
THANKS FOR ALL THE INPUT EVERYONE
JUSTIN

K7n2 delta l boot screen

Similar Messages

Maybe you are looking for