K7N2 Delta-L Jumper J11 problems!

Hi,
i am having problems getting my 2800+ chip to run at speed.
i have got the j11 jumper set to 133/166 fsb. When i take my J10 jumper off safe mode onto user mode 133MHz my computer will start, but the moniter satys blank and the computer just hangs there. When running on safe mode the processor runs at 2200+.
i am fairly sure its not my PSU as i bought a new thermaltake silent 420W, which runs at:
+5V 3.3V 12V
40A 30A 18A
which should be up to the job...
Thanks for any help!!!!!!!!:P

lol i win "spanner of the year" award, rember put cpu fan on the right way round...

Similar Messages

K7N2 Delta Athlon 2600+ Boot Problem!!

Hey this is my first post...
Here is my comp:
K7N2 Delta Series MB
Athlon XP 2600+
Thermaltake Volcano 7+
512 DDR PC3200
GeForce 4 Ti 4200
I noticed that my comp is booting at 1200 mhz. My comp is reading the CPU as a 1.2. I checked the bios and turned the fsb up to 200 mhz because my friend said he read in a forum that it was ok to do so. I did this and now my comp doesn't read my video card. It boots up ok just I have no picture. I have tried resetting the bios and still I have no pic. My questions are this:
1)Am I not flashing the bios correctly, and if so what is the best way to do it?
2)Could I have permanently damaged the motherboard or video card?
3)If none of the above what do you guys recommend I do to fix the problem and what have I done to create the problem in the first place?
Well if you can please help. I really want to be able to see windows again or even the bios!
Thanks

set jumper j10 to pins 1-2 and remove jumper j11. set cmos jumper to clear........unplug the power from wall....... press your power button to relieve any charge left in the mb.........now place cmos jumper to save......plug power back in, and try to start it.......if all goes well and it fires up set bios defaults....save and exit bios.............replace j11 and set j10 to pins 2-3.......and restart.
btw jmbook 166 fsb is also overclocking a 2600......default is 133 so take baby steps.

K7N2 Delta ILSR Strange network problems

K7N2 Delta ILSR
2500+ AMD Barton
Radeon 9600 PRO
Windows XP
Hi there,
My network was working fine yesterday but now whenever I plug a cable into the onboard network card, my computer starts having these strange flucuations...Every few seconds the CPU usage jumps from 0% to about 50% which causes the system to freeze for a second, making it a real pain to do anything.
Does anyone have any idea whats causing this?
Thanks,
Shim

Quote
Originally posted by deftonie
The kingston memory I have is on the memory compatibility list.
kingston removed k7n2 from their supported list.
kingston is not on the Good Memory Choices for ALL K7N2 nF2 released boards
for some reason msi have not removed kingston from their supported list.
Quote
Originally posted by pseudemys
So (and I'm addressing the question in particular to Raven): shoud i wait for a some kinda accident, crash, whatever sooner or later? I'm really scared about such things. You know... everything seems ok and then, suddenly, a nasty surprise. Which is the problem with kingston and k7n2 series? Further, I'd like to buy another 512 M stick and honestly it seems more sensible to me to mount two equal sticks. And I feel somewhat stuck...
a memory can be incompatible but still work.
alot of people buy any memory they can and throw in and it may work.
but it can start crashing after installing some program or updating bios or drivers.
thats the reason i posted the memtest program.
worry about a crash....no reason for that as you self said memtest reported no errors prime95 no errors and doom3 worked good.
kingston uses many different chips on their memory and its those chips that is the problem.
one guy found out that on the specific memory he bought kingston used 3 different chips on.
only 1 of them worked good on k7n2.
so a 33% chans of success in getting a good module is considered bad.
so write down the numbers on the chips and take it with you to the store and compare it to the memories they got.

K7N2 deltas mainboards have a problem with usb devices ??

Ok here is my problem..
I had installed WinXP Pro with SP1..
I got a 20 GB USB2.0 disk.i connected it on the both front or rear usb ports.
When i tried to transfer files to my usb disk or to my PC, in the middle of the copying, i got "Write Delay Failed" error and lost my usb connection..
I had to plug it out and in again..
Now, i have an DSL modem..Last night, i was disconnected from internet and my modem's lights gone..I plug it again, no lights..restarted my PC, also completely shutdown Windows XP..Again no lights..
Then, formatted PC and installed windows 2000 Pr and SP4, until now, my modem worked fine..But USB 2.0 ports are still no use for my usb disk...
In bios , it's enabled as USB 1.1+2.0..
I think this K7N2 deltas have a problem with usb 2.0 devices and Win XP Pro..
Some guys talking about, removing 9th wire earth, but couldn't understand which wire from where ? From mainboard or from usd device's cable ?
Those cables are fabricated, i think it's impossible ?
My processor is Athlon 2500+, ram Twinmos 512 DDR 400
Thanks for reply

I'm also having this problem. It's happening with my USB flash disk. I was almost buying another one when I tried it with Windows Vista on the same machine and it worked ok, then I tried Arch Linux (with kernel 2.6.30.5) on another machine and got the same error. After that I tried Ubuntu and it worked ok. Seems that Arch's kernel doesn't like my USB flash disk.
Last edited by esdrasbeleza (2009-09-02 01:16:09)

MOVED: K7N2 Delta Upgrade Power Off Problems

This topic has been moved to AMD SocketA based board.
K7N2 Delta Upgrade Power Off Problems

Thanks for the various suggestions. I can confirm:
- 4 pin cpu power plug connected
- front bus frequency changed to 200MHz, processor now recognised correctly as Athlon xp3200+
- I have been assured the cpu has not been overclocked
However power off problem persists. System shuts down after approx 1 minute whether i am in BIOS or start initiaiting xp repair from CD. As the system shuts down after such a short time the xp repair will not complete. The system wil not power on again until at least 15mins has elapsed then promptly powers off again.
I have fitted the D-bracker diagnostic tool and this shows 'operating system booting', ie four green lights.
I note from the motherboard maunal that a cpu thermal protection system is installed for the Athlon cpu platform. If the mechanism senses an abnormal temperature rise it automatically shuts down the system. As noted in my original post the system is powering off with the cpu temp at <40 deg C. The cpu warning temp in the BIOS PC health check stsus facility is set at 60 deg C so do not think this is the issue?
System details:
MSI K7 N2 delta (MS-6570)
Athlon xp 3200+ (AXDA3200DKV-4E)
Corsair twinX 1024-3200C2 DDR-DIM 1024 MB
Seagate ST340016A 40MB HDD
Pioneer DVD Rom
Generic CRD - BP1500P CD
1.4MB mitsumi FDD
Thermal take TR2 470W psu
Coolermaster xdreamII socket A cpu fan
Gigabyte geforce 6600GT turbo video
soundblaster live 5.1
Anyone any further thoughts?

K7N2 Delta Series and hdd problem

10 HDD's in machine, about 3 TB (1 TB Lacie external hdd included)
Secondary slave had 160 GB Samsung SP model and it showed it as 130 gb
(and rest is "blank" and can not been formatted or anything)
I thought it went broken (1 year old and no problems before)
I tried it in another computer and it showed all 160 GB.... Strange..
Now i got new same kind 160 GB Samsung and it is just 131 069,3 MB
It just maximum i can now make a partition.. Where is rest of my 160 GB disk ?
What is wrong now.. newest bios, Windows 2000 SP 4 with all updates,
did mobo just broke ?

its not mobo problem. its OS related. all delta series works fine no problem with any hdd's
this links must be usefull for you:
http://support.microsoft.com/?id=305098

K7n2 Delta-l Xp Install Problems

Hello
I have:
AMD 2800XP
MSI K7N2-L
256MB PC2600 GENERIC
HD MAXTOR 160GB ATA133
S3 VIRGE 4MB
Ok, I start to install Windows XP and after charge all drives to start the real instalation the system frezze in a black screen. It's is just before XP ask to choose unit to install C: D:
The bios detect HD, and all the other things. And I have tried with another HD 80GB and with a FX5600 card. And I can't start windows XP instalation. The system charge all drives to instalation black screen and frezze system.
Some ideas?¿?¿?¿

Quote
Originally posted by tower2010
Finaly was a RAM problem. I have put a new module and works Samsung DDR333 256Mb
But now WinXP instalation only recocognize 131GB and the Maxtor HD is 160GB. Motherboard detects 163GB but WinXp not.
Thank you very much.
xp only supports up to 137gb without sp1.
if you read my trouble shoot guide you will find a link on how to slipstream sp1 onto a xp installation cd then you get support for big harddrives right from the start.
aslo usb2 installs directly.
im using a slipstreamed version and i have no trouble with my 160gb harddrive.

[nForce] K7N2 Delta ILSR 1gb kit problem

I recently changed my memory from two Kingmax 256mb memory modules to a Geil 1gb kit. I was surpwised to find out that my system wasn't stable anymore. It restarted after only a few minutes of playing NFS Most Wanted. I tried running Memtest86 and it found lots of errors. Same was with Prime95's torture test witch stopped after less than a minute. I blamed the memory modules cause my previos modules worked flawlessly in both tests. First i tried leaving on just one of the two geil memory modules. It worked just fine. I tried the other module and it worked also. But together it dosn't work even if i put them in sigle channel mode (first and second slot). I went and tried the kit in another dual channel machine. Tested with Memtest86 -- ok. I thought it was some kind of incompatibility between the board and the Geil memory modules so i tried another two 1gb memory kits (one from Gskill - 2 3 3 6 and one from Twinmos 2.5 3 3 8). They all gave me the same kind of errors in test #5 of Memtest86 exactly at the same time (when reaching 95% of the test). I'm beginning to think that the board doesn't support more than 512mb of ram even if the manual says 3gb max.
Can you help me, please?

Quote from: Djibrille on 04-December-05, 02:51:32
Do you know of any problems I can get by running this high VDIMM for a long period of time? I woudn't whant to burn my kit for I intend to keep it when I upgrade my system. That will be when I can get a Athlon64 X2 and mobo (MSI or DFI Nforce4) at a resonable price (this means next year probably).
no.. you are nothink about worry.. its 100% safe. this memory can handle 3.1Vcore...(still working wihout any problems,got a 4 machines with same memory at 3.1V running at 24/7 for 4 mouths) without special cooling..
2.8V is nothink for that memory im glad that my BIOS solve your memory problem. and "CPU upgraide for free" : wrote: "I definently have your bios loaded but instead of 32 bit cpu XP3000 I have shown 64 bit 3000. Cheap upgrade!" 2hits with one

MSI K7N2 Delta, D Bracket LEDs problem

CAn anyone tell me where to find out information on the D bracket. My new system wony start and it indicates a problem with the inializing of the floppy drive controller. I have so far tried 3 floppy drives and four leads.

Hi neusaap,
Are all the optical, DD5.1 software settings correct?...
I had also these problems, but only with MP3 files. I checked the settings, and muted the mic. line in, video I do not need. It's also important to ground your rig and receiver.
Take care

K7N2 DELTA. CD-RW problem

Hey guys, since this is my 1st post, i hope i might be of some help in the future, oh and Merry Christmas to everyone too. Well, my problem is: I have a MATSHITA CW-7585 ( yes its old) and whenever i try to burn something using various progs, it says that " this cd is not a recordable disc" each time?? I've tried connecting it in slave and master , but notihng changes
XP 2500 Barton
512 DDR
MSI Geforce 4 ti,
Win XP 32-bit
420 watts power supply

yes it does with my ohter pc which is running XP sp1 as well. Like i said, whenever i put an emppty cd-r/rw it says that this disc is not recordable

K7n2 Delta ILSR - DVD writer problem

Hi
My system is a AMD athlon 2600, 1Gb Crucial DDR 400 RAM, Tyan tacheon 9600 pro and a pioneer A106 DVD writer.
I have connected IDE1 to the hard drive and IDE 2 to the Pioneer DVD writer.
When
i) IDE 2 (DVD) is NOT connected the system boots up very quickly.
ii) IDE 2 is connected , the sytems start up time is a lot slower.
The DVD writer works then intermittently and sometimes doesnt even respond in explorer.
Anyone got any ideas on why this is?
Thanks
Shaz

got it jumpered right
using a modern 80 wire ide lead blue end in the board,not the older 40 wire ones

K7N2 Delta-L: Strange cold boot problem & solution

My K7N2 Delta-L has a problem cold booting when the vcore is set in the bios at 1.65v of higher. After a cold boot, you get a blank black screen. I noticed that even if you run at default speeds but set the vcore to 1.65v of higher the problem still occurs. There is no problem rebooting however.
I found the following solutions:
1. After you power up and get a blank, hit the reset button.
2. Don't unplug your PC. My PC is connected to a AVR and after I power down the PC I usually turn the AVR off. If i do this, than the computer will have a booting problem if I try to boot it up 30 minutes later or so. Now if I don't unplug it/power off the AVR than everything is fine.
I don't understand why it acts the way it does though.
Does anyone know of any other solutions?

Have you cleared the cmos. If you do be sure you have the power turned off don't move the cmos jumper with the power on.
I found that turning off power at power supply and unpluging, than turning on the computer the fans will spin just a little this drains all the power. Clear cmos 2-3 than return to
1-2 position.
Than plug the power back in and turn it back on, than try the computer again.

K7N2 Delta problem after flashing from 5.0 to 5.3

I was using my K7N2 Delta nicely but after flashing the BIOS from 5.0 to 5.3 in LiveUpdate3 (all OK) and then when LiveUpdate ask to reboot... GOOD BYE!
When bootin the D-lights show that I have a processor damaged or not intalled properly (two red light up, and two green down...).
My processor is an Old Tbird 1.2 Ghz with 100FSB.
The question is: Why the mother stops recognicing the processor if before flashing BIOS worked nicely?.
J10 and J11 jumpers:
When I opened case to check out, I had the green J10 and J11 jumpers closed in the mother. The J10 was in safe mode, and the J11 jumper was closed...(133FSB-166FSB??).
I only have another athlon 1.1 ghz FSB100 processor to test the mobo, but I don´t want to take the risk of burn that one two (if is that the problem, of course).
So... I want to know how can I reflash the bios back (I have the old BIOS in a backup floppy disk, of course)... or if anyone else have the same problem as me....
Thanx a lot guys, and please help me... I´m very sad by now... because I don´t know how to get my computer to work.
Jose.
(from Argentina)

Garry,
Just add
group.Administrators=system
in your filerealm.properties file to login into console.
Hope it helps,
-satya
garry payten wrote:
I am migrating from 5.1 to 7.0 on Solaris. I was able to run the conversion of the weblogic.properties file to config.xml, I was also able to start the new admin server, but I was not able to log in to the console. I get the following error:
Authentication Denied
The username or password has been refused by WebLogic Server. Please try again.
I verified that the WL_USER and WL_PW were correctly set in the startscript and that the system password was set in the config.xml. Any hints? Thanks

Jumper Settings for K7N2 Delta LISR and Athlon 3200 FSB400

Hello Everyone,
(I think I sent this to Raven By E-Mail but I'm not sure, I'm still new to this)
Having problems understanding jumper settings.
I cheched out the forum and the motherboard users guide to see which way the jumpers are set for my Board K7N2 LISR + Athlon 3200+ 400FSB.
In the user guide it say's:-
FSB Mode Jumper: J10
This jumper allows you to set the CPU FSB mode, (It then shows two diagrams of Jumper 10) - first with pins 1 and 2 jumpered "user mode default 133Mhz" and the secound shows pins 2 and 3 jumpered "safe mode 100Mhz".
What has settings 133Mhz or 100Mhz got to do with a 400 FSB??????
CPU FSB Frequency Jumper: J11
This jumper is used to specify the CPU FSB frequency. (again it shows two Diagrams) first: Leave the jumper short connected if a 133/166Mhz FSB is installed.
Secound:If the CPU supports 100Mhz FSB, leave the jumper open connected.
To use a 200Mhz FSB CPU, set the jumper short connected and enter BIOS setup Utility to adjust the CPU FSB Clock Frequency.
Again what has 133/166Mhz or 100Mhz got to do with a 400 FSB???????
For my K7N2 Delta LISR and Athlon Barton 3200+ 400 FSB, what Would I set J10 to:- (Jumpered Pins 1 and 2,= 133Mhz) or (Jumpered 2 and 3,= 100Mhz).
Also what would I set J11 to:- (Jumper pins Open = 100Mhz) or (Jumper short 133/166Mhz). Hope someone can help!!!!!!!!!
It would be nice if the User's Guide had a (If .... Then..... in it)
If CPU = Athlon 2800+ 333 FSB, Then J10 is jumpered pins 1 and 2,
If CPU = Athlon.... etc etc.... or even a couple of examples
Sorry this is so long, but I just need to tell someone, Thanks.

1 insafe mode it will boot at 100 fsb regardless of what you set in the bios
in user it will boot by what it sees the cpu as or what you set it to in the bios
just leave it in user
if you o/c and it will not boot shut down put it in safe
then lower the o/c once it boots
again shut down and put it back in user
2 just leave it shorted
only alter it if you used a 100 fsb cpu

MSI K7N2 Delta-ILSR MB Problems, Need Help ASAP!! PLEASE

Ok I just got this motherboard (MSI K7N2 Delta) Yesterday and after getting it setup I began overclocking the Processor (an AMD Athlon XP Barton Mobile 2500+) I was at 11x 215 1.750V Perfectly. I moved to 216 it started to seem unstable so I pushed the VCORE up to 1.775 and tried 217. It couldn't boot so I dropped it back down and decided ok 208 and a 11.5 multi might get me past the 2.4 mark which I was looking for. Well when I changed the Multi. to 11.5 and said save the system just sate as the flashing y for save. I could not change it to n I had already pushed enter So i firgured great and left it alone for a few minutes, nothing so I reset it. Now it refuses to boot/post. It spinds the fans the HD's the Network port is going but I get no picture. I have cleared the CMOS using the jumper I have removed the battery and power for over an hour and I still get nothing. I am assuming this is a BIOS error but I am not sure what to do to fix it. Does anyone here kno maybe, something I have yet to try something I can do? I would hate to RMA it and have to wait on newegg. Hell the thing is a day old. So please any idea's are welcome I have this posted on the Hard Forums as well but I am hopinh this forum may be more popular with getting help as no one is helping over there. Thanks!

Hi,
Cross: Just in case you are doing something wrong there's a clear CMOS guide here, follow it to the letter (and don't forget to put the FSB jumper to SAFE beforehand - there's a note about it in the guide).
How To Clear the CMOS
Your system board or CPU maybe not be dead yet - I had a similar problem with one of my boards and I tried everything - to cut a long story short I eventually got it working!!!
Btw, If you can't boot or get into the BIOS put your other CPU in (clear BIOS again after fitting!), so that you can prove whether your motherboard is working correctly!
Good luck! I'm off ta bed!
Axel

K7N2 Delta-L Jumper J11 problems!

Similar Messages

Maybe you are looking for