K7N2 Delta LISR Resetting problem

Hi Guys Posted a while back regarding my system resetting all the time and have done the two things that were recommended to me me which was proper power supply and recommended memory as you can see i have spent £160 on these two items and am now pulling my hair out because my system is still resetting when i do anything that is graphically or resourcingly more than just surfing the net
the heatsink is fine and on correctly temps are fine and do not rise above recommended levels
8 x AGP is disabled
but i still get a reset with windows informing me that the system has recovered from a serious error and the following is the reason shown when i click on the show detail button:
C:\Windows\Minidump\mini020604-03.dmp
C:\Documen~\1Longsh~\Locals~\temp\wer1.tmp.dir00\sysdata.xml
I am at my wits end all bios and drivers are up to date but the system just keeps crashing I am about to throw this board away and waste another £80 that I dont really have please Help me PLease Please Please

Did you try troubleshooting the system as I posted earlier? Also try uninstalling Norton and see what happens...you couldn't pay me to put that on my system...it's so intrusive into your system's registry who knows what havoc could be happening...
AVG 6.0 Free Edition or AVG 7.0 Pro version are great virus scanners...much less intrusive to the system and I've fixed many a system sporting good ole' Norton on em that let worms, viruses & trojans through...Had one machine with Norton on it, uninstalled it, installed AVG 6.0 Free Edition and found 146 instances of viruses, worms & trojans...
I never laughed so hard in my life...if you could just have seen my clients face that day...LOL
It's a driver or registry error of some sort so doing a clean install and a careful reinstall of your programs and such should get you fixed up I imagine...
Bonz

Similar Messages

K7N2 Delta LISR SATA problem

Can anyone tell me regarding the K7N2 Delta LISR SATA HDD...
do we have to create array first b4 installing win98/winxp?
I can't find the way installing without creating an array. I remember it's not required for KT6 Delta?
after creating array, in fdisk mode it run so slowly!!! Is it normal?
anyone help is appreciated!!!
p/s: it's single SATA 80GB Seagate HDD

https://forum-en.msi.com/index.php?threadid=50531&sid=

MSI TI4200 VTP not registering in windows XP K7N2 DELTA LISR

Hi All First Post and very Confused
Spec First
MSI TI4200 VTP Graphics
K7N2 Delta LISR M/B
AMD 2800 CPU
1GB Samsung P2700 DDR Ram
500 w PSU
80gb ATA 133 HD
120gb SATA HD
Windows XP Proff Edition OS
Problem is that I have just built this computer installed windows and all MB drivers and everything is fine I then install th Graphics card drivers and I get a blue screen upon the restart that is to quick to read and the system just reboots to the safe mode selection screen this is an ongoing loop if i select start windows normally. If i select safe mode the system boots up in safe mode.
I also noticed after I had taken windows back to last known good configuration that windows had not recognised my card and just showed VGA adapter with the yellow exclaimation mark. I have tried another graphics card and that worked fine.
windows installed it etc automatically
How can I read the blue screen or what is on it as it flashes up so quickly and what do you fine people think my problem is I have disabled 8x agp in bios
The TI4200 came out of my previous MSI KT400 Ultra
Please help
Longshanks

what was the other vga card
post max amps of psu
try it at agp x4 ,disable agpx 8 in bios

Jumper Settings for K7N2 Delta LISR and Athlon 3200 FSB400

Hello Everyone,
(I think I sent this to Raven By E-Mail but I'm not sure, I'm still new to this)
Having problems understanding jumper settings.
I cheched out the forum and the motherboard users guide to see which way the jumpers are set for my Board K7N2 LISR + Athlon 3200+ 400FSB.
In the user guide it say's:-
FSB Mode Jumper: J10
This jumper allows you to set the CPU FSB mode, (It then shows two diagrams of Jumper 10) - first with pins 1 and 2 jumpered "user mode default 133Mhz" and the secound shows pins 2 and 3 jumpered "safe mode 100Mhz".
What has settings 133Mhz or 100Mhz got to do with a 400 FSB??????
CPU FSB Frequency Jumper: J11
This jumper is used to specify the CPU FSB frequency. (again it shows two Diagrams) first: Leave the jumper short connected if a 133/166Mhz FSB is installed.
Secound:If the CPU supports 100Mhz FSB, leave the jumper open connected.
To use a 200Mhz FSB CPU, set the jumper short connected and enter BIOS setup Utility to adjust the CPU FSB Clock Frequency.
Again what has 133/166Mhz or 100Mhz got to do with a 400 FSB???????
For my K7N2 Delta LISR and Athlon Barton 3200+ 400 FSB, what Would I set J10 to:- (Jumpered Pins 1 and 2,= 133Mhz) or (Jumpered 2 and 3,= 100Mhz).
Also what would I set J11 to:- (Jumper pins Open = 100Mhz) or (Jumper short 133/166Mhz). Hope someone can help!!!!!!!!!
It would be nice if the User's Guide had a (If .... Then..... in it)
If CPU = Athlon 2800+ 333 FSB, Then J10 is jumpered pins 1 and 2,
If CPU = Athlon.... etc etc.... or even a couple of examples
Sorry this is so long, but I just need to tell someone, Thanks.

1 insafe mode it will boot at 100 fsb regardless of what you set in the bios
in user it will boot by what it sees the cpu as or what you set it to in the bios
just leave it in user
if you o/c and it will not boot shut down put it in safe
then lower the o/c once it boots
again shut down and put it back in user
2 just leave it shorted
only alter it if you used a 100 fsb cpu

MSI K7N2 Delta-ILSR MB Problems, Need Help ASAP!! PLEASE

Ok I just got this motherboard (MSI K7N2 Delta) Yesterday and after getting it setup I began overclocking the Processor (an AMD Athlon XP Barton Mobile 2500+) I was at 11x 215 1.750V Perfectly. I moved to 216 it started to seem unstable so I pushed the VCORE up to 1.775 and tried 217. It couldn't boot so I dropped it back down and decided ok 208 and a 11.5 multi might get me past the 2.4 mark which I was looking for. Well when I changed the Multi. to 11.5 and said save the system just sate as the flashing y for save. I could not change it to n I had already pushed enter So i firgured great and left it alone for a few minutes, nothing so I reset it. Now it refuses to boot/post. It spinds the fans the HD's the Network port is going but I get no picture. I have cleared the CMOS using the jumper I have removed the battery and power for over an hour and I still get nothing. I am assuming this is a BIOS error but I am not sure what to do to fix it. Does anyone here kno maybe, something I have yet to try something I can do? I would hate to RMA it and have to wait on newegg. Hell the thing is a day old. So please any idea's are welcome I have this posted on the Hard Forums as well but I am hopinh this forum may be more popular with getting help as no one is helping over there. Thanks!

Hi,
Cross: Just in case you are doing something wrong there's a clear CMOS guide here, follow it to the letter (and don't forget to put the FSB jumper to SAFE beforehand - there's a note about it in the guide).
How To Clear the CMOS
Your system board or CPU maybe not be dead yet - I had a similar problem with one of my boards and I tried everything - to cut a long story short I eventually got it working!!!
Btw, If you can't boot or get into the BIOS put your other CPU in (clear BIOS again after fitting!), so that you can prove whether your motherboard is working correctly!
Good luck! I'm off ta bed!
Axel

MSI K7N2 Delta ILSR Memory problems

I'm trying to burn in a system in a 50 deg C (122 deg F) room for a minimum of 12 hours. The main system components are as follows:
Motherboard: MSI K7N2 Delta ILSR
CPU: AMD Athlon XP 2800+
Memory: 2x512 OCZ PC3200 EL
My problem is that the burn-in software continues to freeze up during the memory test. I've already contacted the software manufacturers and the software is stable. It's a problem with the way the motherboard handles the memory. I've tried putting the memory in dual channel configuration and changing the timing settings in the BIOS. The SPD settings are 2.5-3-3-7. Right now I have them at 3-4-3-8. It's a lot more stable than it was under the default settings but it still freezes up sometime after 7 hours. Unfortunately, I wasn't around when it froze so I don't know exactly how long it lasted. I can say that after 7 hours, it wasn't showing any slowdown in performance. If anyone could think of anything else I might be able to do to get the system stable, I would greatly appreciate it.

Thanks for the suggestions. The CPU FSB is 200, so it's already matched up there. And we have a ton of fans already. There are two in the front, 4 inside and 1 on the back. It's a custom case, 2u high. The power supply is oversized and more than adequate to provide the required power. I have four of these units running right now. Two with 2x512 sticks and two with 1x1024 sticks. For each combination, the memory clock speed for one is 166 and 200 for the other. I have been loosening up the memory timings trying to get the system stable, but it still isn't. If the power supply is good, and I'm unable to cool the system anymore due to limititions within the case, is there anything you can think of to stabilize the system. Maybe other settings in the BIOS or suggestions on how to go about getting good timings for the memory. Thanks.

Weird K7N2 Delta (or sth) problem...

Hi all, I'll be quick because I need an answer to my problem as soon as I can...
Today I switched my old Albatron KM18G-Pro with an MSI K7N2 Delta-L, because I had problems with a heatsink on Albatron's Micro ATX mobo...
Ever since I did that, 3dmark01 score has gone at about 1000 (from 13200 to 12100) down, using the exact same drivers for VGA (Triplex Millenium Silver Ti4800SEV 128MB) mobo (nForce drivers v2.03 or 2.45 doesn't matter...). I can see that all tests from approximatelly Nature test and beyond are running choppy. I'm seeing choppy gameplay on screen but the fps on Nature seem correct. My refresh rate is set at the same rate as it was before (75Hz on my Eizo LCD 15" monitor). Fill rate runs too much choppily though the score must be correct. Tried switching to 4x mode but nothing happened. I'm really frustrated here guys so please help me...
ps. sorry for my bad english but I was in a hurry...

hi and welcome to this forum.
the score is not interesting and dont really say much.
whats interesting is how it works in games.
tried any games?
new install of xp?
irq conflicts ?
bye

K7n2 delt ilsr instabilty problem update

have a k7n2 delta ilsr have an issue where it is unstalble ie get bsod at welcom etc at 400 fsb ie 200 setting in bios will run at 166 in safe mode the 3200 cpu is reconised as at 2.39 ghz it should be 2.2 ghz if i run cpucz it says the multiplier is *12 is this a motherbord fault have updated bios too 7.8 latesed have tried diff make of memory power supply but i think the problem is looking me in the face in the fact that the cpu is reconised as 2.39 ghz and the muilt is *12 i think it should be * 11 can any body help regards bazer

yes has latesd bios    AMD Athlon(tm) XP 2700+ here is some info pc wizard 2005
Codename :   Barton
Revision :   A2
Technology :   0.13µ
CPU ID :   6.A.0
CPU IDEx :   7.A.0
Features :
VME - Virtual Mode Ext. :   Yes
DE - Debugging Extension :   Yes
PSE - Page Size Extension :   Yes
TSC - Time Stamp Counter :   Yes
MSR - Model Specific Registers :   Yes
PAE - Physical Address Extension :   Yes
MCE - Machine Check Exception :   Yes
APIC - Local APIC Built-in :   Yes
SEP - Fast System Call :   Yes
MTRR - Memory Type Range Reg. :   Yes
PGE - Page Global Enable :   Yes
MCA - Machine Check Architecture :   Yes
PAT - Page Attribute Table :   Yes
PSE36 - 36-bit Page Size Extension :   Yes
PSN - Unique Serial Number :   No
DS - Debug Trace & EMON Store :   No
ACPI - Software Clock Control :   No
SS - Self Snoop :   No
TM - Thermal Monitor :   No
HTT - Hyper-Threading :   No
SBF - Signal Break on FERR :   No
MON - Monitor/Mwait :   No
DSCPL - CPL qualified Debug Store :   No
TM2 - Thermal Monitor 2 :   No
CID - Context ID :   No
EST - Enhanced SpeedStep Tec...   No
NX Bit - No-execute Page Protec...   No
VMX - Vanderpool Technology :   No
Miscellaneous :
FPU - Co-processor Built-in :   Yes
CX8 - CMPXCHG8B :   Yes
CX16 - CMPXCHG16B :   No
CMOV - Conditionnal Move Inst. :   Yes
CLF - Cache Line Flush :   No
FXSR - Fast Float Save & Restore :   Yes
DAZ - Denormals Are Zero :   No
MMX Technology :   Yes
SSE Technology :   Yes
SSE2 Technology :   No
SSE3 Technology :   No
X86-64 Technology :   No
AMD MMX Technology :   Yes
3DNow! Technology :   Yes
Extended 3DNow! Technology :   Yes
3DNow! Pro Technology :   Yes
SMP - MP Capability :   No
Power Status :
Voltage Control :   No
Frequency Control :   No
Thermal Sensor Built-in :   Yes
Addressing Information :
Physical Addressing max. :   34-bit
Linear Addressing max. :   32-bit
Mainboard Upgradebility :
Socket/Slot :   Socket A
Upgrade interface :   ZIF Socket
Supported Speed :   2200 MHz (or more)
Supported Voltage :   1.6V
al Information :
Performance Rating :   PR-3300 (estimated)
Real Frequency :   2164.89 MHz
Multiplier :   12x
Front Side Bus Information :
FSB Frequency :   180.4 MHz
Bus Speed :   360.8 MHz (DDR)
Initial Frequencies :
Frequency :   2000 MHz
FSB Frequency :   166 MHz
Control Clock Frequency :
Type :   None
Thermal Information :
Core Power :   63.42 W (estimated)
Resistance :   0.46 °C/W (estimated)
Processor Performance Information :
Throttle Mode AC :   None
Throttle Mode DC :   Adaptive
Current Configuration :   None
Throttle :   2164 MHz
CPU Throttle Temperature :   60°C
CPU Shutdown Temperature :   100°C
eneral Information :
A0 (RAS 0) :   256 (Single Bank)
A1 (RAS 2) :   256 (Single Bank)
A2 :   Empty
Memory Controller Information :
Memory Controller :   Standard, EDO
Number of connectors :   3
Max. Module Size :   32 MB
Max. Memory Size :   96 MB
Supported Speed :   70ns, 60ns
Supported Voltages :   5v
Error Detection Method :   8-bit Parity
Error Correction Capability :   Unspecified
Current/Supported Interleave :   1-way/1-way
Chipset Information :
Type :   DDR-SDRAM PC2900
Frequency :   180 MHz
FSB/RAM Multiplier :   1/1x
Channels :   Dual
ECC Diagnostic :   No
CAS Latency (tCL) :   3 clocks
RAS to CAS (tRCD) :   3 clocks
RAS Precharge (tRP) :   3 clocks
Cycle Time (tRAS) :   8 clocks
Information SPD EEPROM (A0) :
Manufacturer :   Samsung
Part Number :   M3 68L3223ETM-CCC
Serial Number :   F6016243
Type :   DDR-SDRAM PC3200 (200 MHz)
Size :   256 MB (1 rows, 4 banks)
Module Buffered :   No
Module Registered :   No
Width :   64-bit
Error Correction Capability :   No
Max. Burst Length :   8
Refresh :   Reduced (.5x)7.8 µs, Self Refresh
Voltage :   SSTL 2.5v
Supported Frequencies :   166 MHz, 200 MHz
CAS Latency (tCL) :   2.5 clocks @166 MHz, 3 clocks @200 MHz
RAS to CAS (tRCD) :   3 clocks @166 MHz, 3 clocks @200 MHz
RAS Precharge (tRP) :   3 clocks @166 MHz, 3 clocks @200 MHz
Cycle Time (tRAS) :   7 clocks @166 MHz, 8 clocks @200 MHz
Information SPD EEPROM (A1) :
Manufacturer :   Samsung
Part Number :   M3 68L3223ETM-CCC
Serial Number :   F6056193
Type :   DDR-SDRAM PC3200 (200 MHz)
Size :   256 MB (1 rows, 4 banks)
Module Buffered :   No
Module Registered :   No
Width :   64-bit
Error Correction Capability :   No
Max. Burst Length :   8
Refresh :   Reduced (.5x)7.8 µs, Self Refresh
Voltage :   SSTL 2.5v
Supported Frequencies :   166 MHz, 200 MHz
CAS Latency (tCL) :   2.5 clocks @166 MHz, 3 clocks @200 MHz
RAS to CAS (tRCD) :   3 clocks @166 MHz, 3 clocks @200 MHz
RAS Precharge (tRP) :   3 clocks @166 MHz, 3 clocks @200 MHz
Cycle Time (tRAS) :   7 clocks @166 MHz, 8 clocks @200 MHz

Mystery Device on K7N2 Delta L in problem state

I have the k7n2 delta L motherboard with an athlon xp 2800+ processor and I'm running windows 2000 pro sp4. In the device manager under "system devices" I have a device listed as "motherboard resources" with a yellow exclamation symbol and the properties indicate code 14 restart computer to get the device to work properly. I've done this to no avail and also reinstalled the drivers from the msi cd. The properties say its on the pci bus and uses input/output range 0060-0060 and 0064-0064. It also indicates driver version 5.0.2195.6717. What is this device and how do I get it to work?

Got a clue from German forum, I'll quote:
- Fixed the exclamation point under Motherboard Resources of Device manager in Windows XP when use USB keyboard/mouse and set as "Support via BIOS".
So I checked the driver for the keyboard and it was version 5.0.2195.6717 same as the "motherboard resource" with "!" . So more details: the keyboard I was using for my new system was my old compaq presario usb keyboard with funky "easy acess keys". And I had usb keyboard support enabled in bios. So I shut down, removed the keyboard and replaced it with a standard ps/2 keyboard and rebooted. And voila the motherboard resource no longer had a "!" next to it. Anyway since it wasn't causing a fatal problem I'm back to using the compaq keyboard until I get another standard boring biege ps/2 keyboard. I'm glad I didn't go on a vmware goose chase.
athlon xp 2800+
k7n2-L
2×512MB PNY PC2700 333MHz Dual channel mode
geforce fx 5200 agp
maxtor 120GB 133 7200rpm
us robotics 56k v92 controller based modem
IEEE 1394 firewire card 3+1
startech 300w PS (ap-350x)

K7N2 Delta ILSR memory problem

I have a K7N2 Delta ILSR board with Athlon XP 2500 with 2 Gig of Mushkin Black Line ram (the ones that are
suppose to be CL2). I change the FSB to 200, and my memory won't run at CL2. Want to raise the Dram voltage
to 2.8V to see if it would make a difference. I looked all over this site for the modded bios 7.8. Does anyone
have the modded bios??? Any help would be appreciated.......

He/She overclocked the 2500+, to make it become a 3200+. Done it myself, but it mostly works with the first step of the 2500+. - That means the overclock forum.
Well, CAS 2 is a very tight timing, which I don't think is possible. In general on Socket A systems:
- FSB 133/266 --> CAS 2 or 2.5
- FSB 166/333 --> CAS 2.5
- FSB 200/400 --> CAS 3

MSI K7N2 Delta-ILSR Power problem?!

So I worked all last night trying to fix the damn thing. It wants to keep powering off on its own. So I unplugged all the devices from the board and powersupply except the only needed items, the board, power switch, and memory (cpu fan of course left on). Still turns off. Reset bios, still. Put system into safe mode by the jumper. Still.
Okay so I gave up, and took the board, memory and processor into a local place that sells these boards. They have seen a few problems with them. 4 hrs later, $55 short they tell me the heat sink wasn't on the chip right so it caused the board to think it was hot and shut itself down right away! He said he ran it for most of the day. So I am like whatever! He left it on there how he had it. I took it home, hooked it back up, and there it goes again!
The 1st night it ran fine, no hd, but I ran it the whole evening. The 2nd night I powered it up, it started to do this. Nothing changed. So now I am getting ticked off. I am about to take my whole case, and system back to those guys and tell them see....
Anyone who has used this board have any ideas? I have built many systems and this is the first one that is being a pain in the butt.
PowerMAX 400w powersupply.
LP-8800D MODEL #

Powersupply was brand new and came with the case. :(
Quote
Originally posted by twistedbrowntucker
Quote
Originally posted by rzotz
What I am noticing is that when it sits for 10-15 min, and I try to turn it on again, it takes a little longer before it turns off. It actually may stay on up to 5 sec, then turn off. But if I try again a few times in a row, maybe .5-1 sec it cuts off. I have already reseated the heatsink on the processor again.
Powersupply is rated at:
+12v - 25amps
+3.3v - 28a
+5vsb - 2.0a
Power supplies can go bad at anytime.Take the whole thing up there.Case and all and let them check it out.BTW all power supplies aren't equal. IMHO buy an Antec TruePower 430 or 480 watt

[nForce] K7N2 Delta@ LSR stability problem

Okay gang...here's the scoop. Recently purchased the K7N2 Delta2 LSR and equipped it with an AMD XP-2600 (locked), 2X512 Rosewill Dual-Channel sticks, plus Samsung 80gb HDD and ATI Radeon 9000pro AGP. Built the system with no hassle and clean installed Win XP Home. Just wanted to get the system up, so left BIOS setting where they were for a couple of days. Noticed that the processor was not being recognized, so checked the BIOS and realized FSB was set to 133 (processor at ~1500mhz). I changed the FSB to 166 with multiplier of 11.5 (which, I believe is correct for my 2600 Barton). Voltage is at 1.65v. Memory is at DIMM slots 1 & 3 (dual channel) and memory voltage is at 2.7v. (Timings at 2.5,3,3,7) After I made these changes to the BIOS and rebooted, Win XP ran checkdisk, and reported no errors. The problem now, is that graphics-intensive stuff (i.e., games) cause system to freeze after about five seconds. When the processor was underclocked, I didn't have this problem. I'm not interested in over-clocking... just want it to be stable at stock speeds. Other applications (Word, Excel, IE, Outlook Express) run fine. My ATI Radeon 9000pro is a 4X AGP card (I have 8X disabled in BIOS), and the voltage is at 1.5v. I don't think this is a PSU problem (400w), and only noticed the problems since changing the FSB to where it was supposed to have been all along. Am I missing something obvious?

Board runs best with fsb:dram at 1:1 Not sure what speed memory you have but needs to run at same speed as fsb, ie 166 Mhz =333 ddr.
I found bios b3 to work best for me. Give that a go.
Give make/model of psu with max amps to +3.3v, +5v and +12v. See my signature for example.
I found that with other bios I need high performance setting in cell menu at optimised, so check that.
Search on this forum for my username and keyword 'bios' for lots of other posts.
Good luck

MSI K7N2 Delta-ILSR, Mouse problem & Video off problem solved!!!

I find the following information that I collected very interesting at the very least...
Here goes...
The video off problem that I was having was directly linked to the mouse. Here, let me explain the video off problem. In the BIOS Have the Standby mode set to S3. The problem occurred when I started windows, then went into standby, then started back up, then restarted the computer, the monitor would act as if it were in sleep mode, or rather there was no signal being sent to the monitor. Well the odd way I fixed that is by plugging in a standard 2 button PS/2 mouse. Also this fixed the issue with the mouse sometimes not working in windows.
Here is how I tested.
Logitech MX700 Cordless Optical Mouse, PS/2 & USB= failed.
Logitech iFeel Optical Mouse, USB= failed.
Microsoft Cordless Ball Mouse, PS/2= failed.
Standard Artec (Cheapy brand) Ball Mouse (With no wheel), PS/2= All issues fixed, and passed.
When I said failed I do not mean they didn't work, I mean they sometimes didn't work and also caused the Video off problem after restarting the computer.
Obviously it isn't the ports (PS/2 or USB) that are the problem, it is more like the mouse itself, and the amount of buttons in particular. As you can see above the only mouse that works correctly is the one that only has 2 buttons, the rest has 3 or more buttons along with a Wheel. The MX700 has 8 buttons + wheel, WOW!
Anyways I figure out it was the mouse, and not the memory.
Obviously MSI needs to make a patch for this mouse problem.
I'm still having a hard time believing that the mouse caused the video not to work, but it is true! I spend well over 5 hours testing this crap. Every time with the mice with more then 3 buttons it messed up, and every time with the 2 button old fashion mouse it worked flawlessly!
MSI, get to work on a new BIOS to fix this mess!!! :]
BioHaz

Quote
Originally posted by Raven_
hi
its possible to use an ps/2 mouse AND a usb mouse at the same time.
i used the ps/2 mouse in windows and the usb mouse when playing games.
you can get some trouble if you do it the way i did it.
i was in windows surfing and the pointer just jumped all over the screen.
when i looked on the other side under a table a friends little kid played with the usn mouse. )
bye
LOL, that isn't what I'm talking about.
There seems to be a problem with my motherboard accepting mice with more then 2 buttons. It works the first time, but if you restart the computer, the video goes off. If you have both installed, it still messed up.
BioHaz

K7N2 Delta Nforce2 Audio problem

I'm sure this is a dumb question for the vast majority. I can't seem to get more than two channels to work on my motherboard. I've tried all the drivers and etc.. Don't know what is wrong with it.?.?
If anyone else has had this problem, or rather, knows how to fix it. PLEASE help, a small thing yes...but still...
Oh by the way, I don't have a s-bracket either. Just back panel only. Xp system. Two sets of speakers, right? I should just have to plug into line in and line out if I'm not mistaken. Anyways...

hi
try sound drivers from realtek
this only applies to the L board.
bye

K7N2-Delta ISLR Power Problem

Coming Out of Standby I lose Connectivity to the USB2.0 dbracket connection. Have latest Bios (7.2)
Also, the power light does NOT BLINK when going to standby

Quote
Originally posted by Deathstalker
Conal,
What about your Power Supply? Also please list all your IRQs and every device on each IRQ.
Take Care,
Richard
Antec 330 W power supply...Truepower
Worked with an ASUS board before I traded for MSI
IRQ 00   Exclusive   System timer
IRQ 01   Exclusive   Standard 101/102-Key or Microsoft Natural PS/2 Keyboard
IRQ 03   Exclusive   Communications Port (COM2)
IRQ 06   Exclusive   Standard floppy disk controller
IRQ 07   Shared   NVIDIA nForce PCI System Management
IRQ 08   Exclusive   System CMOS/real time clock
IRQ 09   Shared   Microsoft ACPI-Compliant System
IRQ 0D   Exclusive   Numeric data processor
IRQ 0E   Exclusive   Primary IDE Channel
IRQ 0F   Exclusive   Secondary IDE Channel
IRQ 10   Shared   Creative DI5630 Data Fax Modem
IRQ 12   Shared   WinXP Promise FastTrak 376 (tm) Controller
IRQ 13   Shared   MSI MS-StarForce GeForce4 Ti 4800 with AGP8X (NVIDIA GeForce4 Ti 4800 with AGP8X)
IRQ 14   Shared   NVIDIA nForce MCP Networking Adapter
IRQ 14   Shared   Standard OpenHCD USB Host Controller
IRQ 15   Shared   NVIDIA(R) nForce(TM) MCP Audio Processing Unit (Dolby(R) Digital)
IRQ 15   Shared   Standard OpenHCD USB Host Controller
IRQ 15   Shared   OHCI Compliant IEEE 1394 Host Controller
IRQ 16   Shared   NVIDIA(R) nForce(TM) Audio Codec Interface
IRQ 16   Shared   Standard Enhanced PCI to USB Host Controller

K7N2 Delta LISR Resetting problem

Similar Messages

Maybe you are looking for