K7N2 Delta LSR+Mobile 2600

I can`t seting the BIOS for the cpu MOBILE 2600. The mainboard don´t show the real speed.
How i can set?
i upgrade the BIOS, but just show 1000Mhz..
Sorry for my english!!
can you help me??

https://forum-en.msi.com/index.php?threadid=31708&sid=&hilight=WHAT+TO+DO+IF+IT+ALL+GOES+WRONG&hilightuser=134
https://forum-en.msi.com/index.php?topic=64248.0
It will be at 100 fsb now
so 10x 100 =1000 mhz
if you have the right ram then 10x 200 should be easy
just up the fsb
if it dont book read second link

Similar Messages

  • [nForce] K7N2 Delta@ LSR stability problem

    Okay gang...here's the scoop. Recently purchased the K7N2 Delta2 LSR and equipped it with an AMD XP-2600 (locked), 2X512 Rosewill Dual-Channel sticks, plus Samsung 80gb HDD and ATI Radeon 9000pro AGP. Built the system with no hassle and clean installed Win XP Home. Just wanted to get the system up, so left BIOS setting where they were for a couple of days. Noticed that the processor was not being recognized, so checked the BIOS and realized FSB was set to 133 (processor at ~1500mhz). I changed the FSB to 166 with multiplier of 11.5 (which, I believe is correct for my 2600 Barton). Voltage is at 1.65v. Memory is at DIMM slots 1 & 3 (dual channel) and memory voltage is at 2.7v. (Timings at 2.5,3,3,7) After I made these changes to the BIOS and rebooted, Win XP ran checkdisk, and reported no errors. The problem now, is that graphics-intensive stuff (i.e., games) cause system to freeze after about five seconds. When the processor was underclocked, I didn't have this problem. I'm not interested in over-clocking... just want it to be stable at stock speeds. Other applications (Word, Excel, IE, Outlook Express) run fine. My ATI Radeon 9000pro is a 4X AGP card (I have 8X disabled in BIOS), and the voltage is at 1.5v. I don't think this is a PSU problem (400w), and only noticed the problems since changing the FSB to where it was supposed to have been all along. Am I missing something obvious?

    Board runs best with fsb:dram at 1:1  Not sure what speed memory you have but needs to run at same speed as fsb, ie 166 Mhz =333 ddr.
    I found bios b3 to work best for me.  Give that a go.
    Give make/model of psu with max amps to +3.3v, +5v and +12v.  See my signature for example.
    I found that with other bios I need high performance setting in cell menu at optimised, so check that.
    Search on this forum for my username and keyword 'bios' for lots of other posts.
    Good luck

  • K7n2 delta lsr + 3000XP prob

    i just bought:
    msi kt7n2 delta lsr
    512 pc2900
    3000XP
    450w power supply
    winXP
    i cannot run the processr at 166mhz otherwise windows either brings up the error send report where it closses the application OR windows just restarts without warning.
    my brother just bought the same set up aswell (he had his for crimbo) and hes got the same prob, except when he turns the speed to 166mhz, when windows goes to start he gets a BSOD, so i figure no biggy, just repair windows, as i go to do this before the installation or any questons are asked, he gets yet another BSOD and this happens everytime.
    ive been ****ing round with bios options for a while but i aint very good at that ****.
    and im running a ti4800 nVidia
    i dont know wether to upgrade the bios because
    A: i have never upgraded a bios before
    and
    B: if i were to take the board back hed probaly blame it on me for pratting around with it
    so, what you guys reckon, i noticed in one of the topics that 400mhz ram would be needed for a 3000XP upgrade ?

    The problems your having can be caused by power supply, memory compatiblitly and a few outer things.
    List your power supply amps for 3.3 volt, 5 volt and 12 volt.
    The ram is PC2700 it is 333 FSB ram your processor is a 400 FSB processor.
    So you have created one problem there. Try running ram as single channel to see if it helps with stablity. Set ram speed to 333 FSB.
    Or better yet buy some ram that is on the list of compatible ram 2-256 of PC3200 DDR is plenty of ram for games and programs and will keep price down.
    Memory that is matched for Dual Channel will also help.
    The newest Bios for the K7N2 Delta ILSR is 7.6 it may help with some ram problems but will not fix the FSB difference.

  • K7N2 Delta-ILSR Reads 2600+ as 2000+

    'lo there.
    I got a replacement of my old board and now it only detects my cpu as an AMD Athlon XP 2000+ whereas before it was detected as a AMD Athlon XP 2600+, which is what it is.  I'd really appreciate any help on this topic.  I've searched the forums for similar topics but haven't found the result's I'm looking for.
    so, any takers?

    Hi,
    d1git: You say you've searched the forum on this problem - hmmmm.
    One of two things (or both). Make sure the FSB Jumper on your motherboard is set to "USER" rather than "SAFE". Then make sure the FSB setting (in the BIOS) is set to either 133 (for 266FSB CPU) or 166 (for 333FSB CPU) etc. If you're still having problems then try clearing the BIOS (CMOS) first:
    Look here:
    How to Clear CMOS
    BTW, I'm sure this stuff is in your manual  !!!
    Axel  

  • AMD Athlon 2600+ only reading as 2000+ on K7N2 Delta

    First off, here's my machine:
    k7n2 Delta Mobo
    Athlon 2600+ w/ Heatsink and fan and 333 FSB
    512 MB DDR PC 3200
    Liteon CD-RW/DVD Combo
    60 GB Western Digital HDD
    350 Watt Power Supply
    Let me know if I missed anything
    The basic problem is that My processor is only being read as an Athlon 2000 at best.  I've tried to change every setting imaginable in the BIOS, to no avail.  The highest core/bus ratio i can get is 12.5, at which it reads as 2000, and at 13 it nosedives to 667.
    One interesting tidbit is that if I try to move the J10 jumper from safe (100) to User Select (133/166) the machine doesn't post (I thought I had it figured out for sure there).  It would also be important to note that it was indeed functioning flawlessly and registering as a 2600+ before my other power supply crapped out.  Well, not flawlessly (audio) but that's another post, I guess.

    I'll give that a try.  Thanks for the fast repsonse.  By 'better' psu, do you mean a quality one, or simply with one higher capacity?

  • [nForce] K7N2 Delta 2 LSR boot/power up issues

    I installed the K7N2 Delta LSR mb with an Athlon XP socket A 3000+ cpu.  The computer turns on but won't boot.  Nothing appears on the monitor screen and there are no beeps.  The harddrive spins, the board has power but nothing happens. When I put my old mother board back (MSI K7T Pro266A) in with the Athlon 2000+, everything works fine.
    Maxtor 60 gb harddrive
    512 MB SD pc2100 SD Ram
    Abit 128 mb Radeon 9200SE Video card
    Any suggestions?

    A few things to check:
    Do you have any unused stand offs in the case touching the motherboard 
    The XP3000 CPU is a barton core and comes in two variants, a 333FSB and a 400FSB version.  Your RAM is PC2100 which with an Nforce chipset is a recipie for problems. The NForce chipset is picky about RAM and PC2100 running on a PC2700/PC3200 processor FSB probably won't work.   
    Also post your PSU max amps, as a +12V rail below 16A could cause problems. 
    Do you have a D-Bracket connected ?  This is the PCI insert with 4 leds on ?   

  • K7N2 Delta2-LSR doesn't POST

    Hi there, sorry before if anyone had asked this question before,
    I have a system
    K7N2 Delta2-LSR
    Sempron 2600+
    Adata Vitesta 2x256Mb
    Winfast A250LE TD Ti4200
    PATA hard drive...
    i just tried to oc this system,
    before : Sempron 2600+ @1833MHz, fsb 166, ram timing auto, vcore default 1.5V
    1st trial : FSB 185, ram timing auto, vcore 1.55V, POST success, but i didn't boot to OS, entering setup again, wanna try higher FSB
    2nd trial : at FSB 188, ram timing auto (i only changed FSB and vcore), vcore still 1.55V, my system didn't POST...
    I tried to clear cmos, by moved the jumper, but it still didn't POST. Anybody help me pliz, what problem did i face?
    Thank's

    Quote from: HenryW on 11-August-07, 00:27:10
    Do you have the manual that came with the motherboard? What kind of RAM do you have ( PC2700-333Mhz or PC3200-400Mhz)? If you are going to be increasing FSB you should have PC3200.
     You will need to set the jumper on J10 to pins 2-3 (safe mode) restart PC and reset BIOS to default settings. Next turn off PC & set J10 jumper back to pins 1-2.
     Before attempting to overclock again come back here for advice.
    Yup, i have ram, DDR 500, but i run it at fsb 166.
    what i tried is FSB at 190 Vcore 1.7V (default 1.6V) ram timing 2-3-3-7 T1
    but the cpu temp is 52C (on bios)... is this normal? i only use the stock cooling HSF...
    at FSB 166, temp is 47C. But i touch the HSF, not so hot like that temp, is the sensor wrong?
    Anyway, on the socket A, there is an electric ribbon (sorry, i don't know the name...i name it my self ), is that the sensor for the cpu temp?
    "J10" is nothing on my MoBo, i use "insert" while pressing power button, it worked just the same like "J10" works...

  • K7N2 delta reboot frequently

    Hello ALL
    I have a K7N2 delta with arhlon 2600+ 256Mo.
    My problem is the following :
    My pc reboots frequently since I have upgraded the BIOS (Ver 5.60) and changed my graphic card.
    The temperature of the CPU gets up to 80°c....I suppose it is the reason why my PC reboots...But I dont know why the temperature is so high....
    Can someone help me please....
    Denso

    Hello,
       Welcome to the forum, please start by reading MOAN GUIDE That temp is way to high, sounds like your cooler is not installed properly read  CPU Install Guide and Artic Silver  

  • K7N2 Delta2-LSR Single SATA hard drive set up

    OK, I've set up system described in signature, and followed advice posted in this forum.
    Enabled RAID, set up single drive raid array, did the F6 thing and installed windows without any problem.
    I intended to disable raid in BIOS but when I do the system does not find a hard drive to boot from.
    The only two hard drive boot priority options are array (when enabled) and add-on cards (none)
    At some stage during the set up I did see my sata h/d in BIOS as well as the raid array.  It may have been on IDE Channel3 Master but not there now.
    I'm now thinking of deleting my array using RAID BIOS-F10 but I am concerned not having much experience of raid.
    In particular, will BIOS see my hard drive as it only sees an array now.
    Is my only option?
    I'd hate to re-install windows and my applications again.  If it come to that, I could live with current situation.
    Thanks Dave

    just noticed, your sig lists "K7N2 Delta2-LSR" while your topic title lists "K7N2 Delta-LSR". there is a fundametal difference, hence the confusion
    the old Delta's had the Promise controller for SATA / RAID, as nvidia chipset at time had no native support. now newer nvidia nforce chipsets do. what i described above is correct for Delta, but what you have discovered is correct for Delta2: for single drive, disable IDE RAID, and SATA drive is listed as an IDE device

  • MSI K72N Delta LSR - windows XP keeps stop codes and serious errors Puzzled why

    hi,
       System specs
    AMD sempron 2400
    512mb DDR PC3200 ( 2 x 256nb Matrix module brand memory written on chips )
    MSI K7N2 Delta LSR ( lastest Bios )
    Onboard sound - Enabled
    Onboard lan - Disabled
    Liteon DVD Rom
    CD-RW 52x
    ATI Radeon 9550 ( installed at moment )
    before was a Nvidia FX5700 LE took back faulty as tried radeon 9800 pro and was ok for a couple hours
    got Nvidia FX 5500 - faulty fan making noise on boot.
    Ive built a System up and its been running fine for a few months and then 1 day system crashed and got windows recovered from serious error and and wound't shut down but only restart.
    Replaced memory that was in and checked with mem99 and said it was faults so replaced memory and shutdown problem vanished.
    Few days later windows xp started saying recovered from serious error again with stop codes
    0x0000050
    Bccode 10000050
    Bccode 1000008e
    Bccode 1000000a
    Stop Code D1
    They was the stop codes been getting since, some said Page_fault_in_nonpaged_area, IRQL_not_less or Equal
    Im puzzled what the problem can be know, even tried reformatting and reinstalling windows twice and not solved it, tried a another cdrom drive and still same.
    Im puzzled what the problem can be.

    Temps are fine running about 45'c in windows and max about 52'c when in full load ive got motherboard monitor on all time monitering temps and also recording and save out log file when turned off for temps.
    Its a retail boxed AMD Sempron which i dont think much to the stock heatsink and fan ( Athlon 64bit ones are loads better copper base and heat compound instead of sticky pad )
    The new memory is only think is got whats wrote on the memory modules is called Matrix, I know from past experience's when u reinstall windows and files cant copy across ok and keeps saying cant read file etc or cant copy file during installation thats indication bad memory strip, ive even got a memory thats fault ( i only use for testing and diagnostic ) as 1 of the memory modules comes up fault in memtest96 and even tried that and still same, thats how i found out in first place memory was causing system not to shutdown properly.
    What i can try is my memory as ive got 1.5gig in Elixir branded and i know thats ok 100% with nforce 2 boards as i had a MSI K7N2 Delta ILSR and ran elixir memory with np, before i got a Gigabyte KT880 board.
    Antivirus ive got running on system at the moment is AVG and always used it all time, it dont use any cpu usage and also saved my system loads from virus as it caught them as they tried to run and stop them, something norton's dont seem to do very well.
    I give modem a try on a USB hub but its strange when u unplug USB its ok and NTL recommends when modem stops working to unplug power from back modem and leave it a while and it comes back on, done this in past successfully but this time its blue screening, Which could be part of windows main files are corrupted. The USB Modem is running of its own PSU so shound't be using USB power at all, if it was that explain blue screen when taking power off as it do it when taking usb out.
    Error codes ive watched a Microsoft web broadcast ( over a hour long ) about error codes and 40% of them are software + hardware related combined they make it sound so easy to diagnose them but in reality unless u know windows 100% its hard to.
    Harddrive seems to copy files ok across and back, i have to try another Harddrive and see but from past experiences when Harddrives are about to fail windows seems to stall, lockup and also just stop responding when accessing certain programs or files.
    Its a confusing 1 as u solve 1 piece of puzzle another comes up and throws u off track again.
    Looking that all parts ive replaced so far have solved 1 or another problem to only reveal another hidden, PC's who have them lol
    If i solve it i post my finding np it keep me busy for a couple days testing things, u learn something new every day with pc's new faults and problems and how to solve them, try too lol
    And most of time its compatibility problems but odd times hardware or software.

  • More K7N2 Delta ILSR issues

    After resolving many issues I've got with my K7N2 Delta ILSR (I still have no regret because I choose it over Abit or Epox), there are still some problems I could not overcome:
    1. the system cannot resume standby (it goes in S1 or S3, but hangs when resuming before any image appears on monitor)
    2. at a freq when I have stability with default vcore, raising vcore is producing instability (system freeze when running prime95)
    3. system temp reported by mbm -last version- seems high: 48-52 degrees; the proc temp is always 4 degrees -no more, no less- higher
    My specs: K7N2 Delta ILSR, Barton 2600@2170Mhz (10.5x206)  cooler master aero 7+,
    4HDD: 2SATA raid 0 Maxtor 120Gb, 1Maxtor 200Gb and 1 WD 80Gb on IDE3 (Lumberjack mooded bios 7.6),  1 DVD-RW Pionner 106D, 1 CD-RW Yamaha F1, 1 CD-RW Plextor 48\24\48,  Hercules Radeon 8500 128Mb ,…, Psu Chieftech 420W (very stable voltages -reported in mbm- when running Prime95 and (or) other killer appz), Thermaltake Xaser III V1000A case

    Anybody? I am worried in particulary about the imposibility of resuming from standby... please help

  • Bios for K7n2 delta 2 LSR (2800+ Mobile Barton Recognizing)

    Hi, i need the BIOS for the Bios for MSI K7n2 delta 2 LSR Motherboard, because i have a Mobile Barton 2800+ CPU with FSB 266 and it isn't recognized correct, i would like to set the Multiplier to 16, the highest setting is 13 - but at 13 my system didnt boot anymore. I tried the B72 Bios, but it didn't help. Thanks

    What's that? You already asked for that in another thread (https://forum-en.msi.com/index.php?topic=123557.msg932826#msg932826). Please don't open various threads for the same issue.
    I already said in the other thread you can't set 16 manually. Set it to auto.

  • Does anyone know where I can find a K7N2 Delta 2 LSR modded BIOS?

    Does anyone know where I can find a K7N2 Delta 2 LSR modded BIOS.  Specifically I am looking for more Vcore options and higher multipliers for my XP-M 2600+

    take a look at http://www.nforcershq.com/forum/viewforum.php?f=11&sid=acb692bb0da312f539d5e8f1f3c40d72

  • Where to find K7N2 Delta 2 LSR modded BIOS?

    Does anyone know where I can find a K7N2 Delta 2 LSR modded BIOS.  Specifically I am looking for more Vcore options and higher multipliers for my XP-M 2600+

    take a look at http://www.nforcershq.com/forum/viewforum.php?f=11&sid=acb692bb0da312f539d5e8f1f3c40d72

  • K7N2 Delta-L and Sempron 2600

    Just upgraded my old palomino XP 2000+ with a Sempron 2600+ .
    The thing is that nothing changed in the system except the cpu but now my agp slot is off (no current through it, the gfx card's fan won't work, hence the card itself).  NOTE: i've upgraded my bios to support the sempron cpu

    This thread has been locked, please refer to this thread K7N2 Delta-L / Sempron / AGP not working ?

Maybe you are looking for