K7N2 Delta Post Bios Boot faliure

I just bought the motherboard set it all up and powered it on and all the fans spin up but make a rapid speeding up and slowing down noise. i took the motherboard back to the shop and they replaced it and tested my new one in shop and it worked fine. i took it home put the processor ram and gfx card in and the same problem happened again. on the d-bracket it says its a Processor problem ive tried another processor in it and got the same problem. also the Led's on the d-bracket flash on and off instead of being constantly on.
i am using 512mb Corsair 3200 400mhz Platinum Ram, AMD Athlon XP 2400+ also tried 1700+ to no avail and a Radeon 9700pro. i dont understand what could be wrong as it worked fine in the shop with their ram and 1700+ cpu ;( i could just cry. i have also tried swapping out the power supply with another one :O any help into this problem would be greatly appriciated.

Thepower supply im using is a Q Tec 550watt Gold it is a really good power supply the only thing i could check is swap the memory around the slots and take the motherboard out the chassis and see if it works then...could be a short inside the case :'(. i have cleared the cmos memory and set it to safe 100mhz fsb.i was under the imprestion that the MSI K7N2 Delta was a good mobo i must of been mistaken :'(. what make of ram do you guys use and where could i get some :D BTW i live in th UK (England). im not overclocking anything either :]

Similar Messages

MSI K7N2 Delta-ILSR Wont boot up (no display no bios)

Hi
i bought a AMD Athlon XP 3200+ & MSI K7N2 Delta-ILSR.
unfortuntly i can't boot it. it wont show anything on screen.
i have tried anything i red in this forum (clear cmos... safe mode jumper...strip all parts...)
all i get is :
blank black display, no beeps and keyboard lights flashes over and over (when connected to a KVM hub), when conected directly to keboard the lights flashes only once but stil black display and no beeps (i hear on speake,when powering up PSU, a silent short noise, no beep).
power suply turns on (new one 500w), i tried agp video card and replaced with pci video card.
memory is kingstone 512mb pc3200 400MHz x2, i tried only one of them and both in diferent sockets.
cpu: AMD xp 3200+ 400fsb.
i did succed to go into bios only once, after lots of resets and shutdowns and bios clear (after ouers)
i choosed in the bios: load bios defaults, and thats it. i hoped it starts up but nothing.
i did all testing i know (checked all pins, cables, clear cmos...all, you name it)
all parts are brand new (except motherbord. it's seconds hand from eBay. i've bean talled that it works fine)
i also e-mailed MSI support that question. (2 days ago. no answer yet)
oh...and i have a pci POST diagnostic card and its 7seg display don't shows any numbers, only when once i succed to get into bios. i don't have the msi original D-Breket addon diag.
can you help me?

hi guys
here is my PSU specs:
Colors-It 500w-Max Silent ATX Power Supply
Voltage 115/230V
Current 10A/5A
Frequency 60/50Hz
+3.3 +5 +12 -12 -5 +5SB BLK GRN GRY
30A 50A 15A 1.0A 1.0A 2.5A COM P-ON PG
connectors:
ATX-2.03 Connector: 1
ATX-12V Connector: 1
CD-Rom/HD 4 Pin connector: 6
Floppy 4 Pin Connector: 2
Serial ATA Connector : 1
cpu: AMD Athlon XP 3200+
MotherBoard: MSI K7N2 Delta-ILSR More: http://www.msicomputer.com/product/p_spec.asp?model=K7N2_Delta-ILSR&class=mb
Memory: kingstone 512mb pc3200 400MHz x2 More: http://www.ec.kingston.com/ecom/configurator/PartsInfo.asp?ktcpartno=KVR400X64C3A/512
i have other brand of memory moduls (micron pc2300) i tried them too. no go.
i tried other PSU, i pulled from my brothers pc (amd xp 1400+).
as i said before, i have pci POST diagnostic card so it could tell me any problem. iguss it's the mobo, posibly bios upgrade.
but if mobo not showing bios, i can't update bios from floppy.
and the tested the mobo out side the case on a antistatic mat and i useed an antistatic strip.
as i said i could get into the bios once, after many resets....choosed 'load bios defaults..', restarted and.....no go.

K7N2 Delta Athlon 2600+ Boot Problem!!

Hey this is my first post...
Here is my comp:
K7N2 Delta Series MB
Athlon XP 2600+
Thermaltake Volcano 7+
512 DDR PC3200
GeForce 4 Ti 4200
I noticed that my comp is booting at 1200 mhz. My comp is reading the CPU as a 1.2. I checked the bios and turned the fsb up to 200 mhz because my friend said he read in a forum that it was ok to do so. I did this and now my comp doesn't read my video card. It boots up ok just I have no picture. I have tried resetting the bios and still I have no pic. My questions are this:
1)Am I not flashing the bios correctly, and if so what is the best way to do it?
2)Could I have permanently damaged the motherboard or video card?
3)If none of the above what do you guys recommend I do to fix the problem and what have I done to create the problem in the first place?
Well if you can please help. I really want to be able to see windows again or even the bios!
Thanks

set jumper j10 to pins 1-2 and remove jumper j11. set cmos jumper to clear........unplug the power from wall....... press your power button to relieve any charge left in the mb.........now place cmos jumper to save......plug power back in, and try to start it.......if all goes well and it fires up set bios defaults....save and exit bios.............replace j11 and set j10 to pins 2-3.......and restart.
btw jmbook 166 fsb is also overclocking a 2600......default is 133 so take baby steps.

Band new computer with k7n2 delta will not boot or moniter not working

this is my first complete system build so please bare with me. the system uses a enlight 420 watt power supply in a lan boy case. it has a K7N2 Delta mother board with a 2500 barton amd cpu. the drives include 2 cd drives 1 floppy and one 120g hd, pny 5600 ultra video card 1 g kingston value ram ddr dual channel. when i turn on the power all the fan turn on the led in the front of the case light up but i get no boot or or video card not sure which yet. i get #1 led is red #2 led is red #3 led is green #4 led is green. i has tried to unplug drives with no change. tried a cmos reset with no change. tried a old voodoo video card with no change. tried to set the fsb to 100mhz with no change.
any other idea or suggestions would be helpfull.
justin
just tried used one stick of ram at a time with no change. the p.s. is +5v 40a, 3.3v 30a, +12v 18a, -5v .3a, -12v .8a, +5vsb 2a.

GOT IT TO POST LAST NIGHT. I HATE TO SAY WHAT I FOUND I FEEL A BIT LIKE AN IDIOT. WHAT I FOUND WAS THAT THE RESET BUTTON IS POLORIZED AND I HAD IT ON BACK WORDS. I TOOK ME WALKING AWAY FROM IT FOR A DAY TO COME UP WITH THE IDEA.
THANKS FOR ALL THE INPUT EVERYONE
JUSTIN

K7N2 Delta Won't Boot

Hi All,
I'm new to the forum and I hope you guys can help me out. I'm having power issues with my box. It won't boot!!!! This is was it does powers up then shuts right down. It doesn't boot long enough for me to check anything. It continues to do this if I don't unplug it. Please guys I dying here.
Here's my configuration:
Samsung CDRW
Pioneer DVDRW
Seagate 20g OS Drive
Seagate 80g Data Drive
Sound: Creative Audigy2 w/ remote
512MB Samsung memory
I bought a brand new power supply thinking that would solve my problem. But to no avail that didn't work. So, I disconnected the power and reset cables from the motherboard and jumped the board and it still does the same thing. And it's driving me nutts. I checked the processor and its cool. Could it be a memory problem? I remember getting memory errors like for a week before. Sorry for the long post for a newbie to the forum.
Gurl Out

Hello My MSI Brothers & Sisters
I’m totally confused now (not hard to do) here’s why I just bought 2 K7N2 Delta-L AMD XP 2500 Barton & 1 XP 2600 Barton the XP 2500 box has 1 stick of Infineon PC 2700 @ 256 and the XP 2600 box has 2 sticks of Infineon PC 2700 @ 512 ea (HYB25D256807BT-6) haven’t put them together yet was going to start this week but after reading about all the trouble every one is having with the pc 2700 512 sticks I’m not sure if its going to work or will it is it only the Infineon/Micron my XP 2600 box has to have 1 gig in it its for heavy office work and AutoCad do i need to change memory to 1gig of pc3200

[nForce] K7N2 Delta 2 LSR boot/power up issues

I installed the K7N2 Delta LSR mb with an Athlon XP socket A 3000+ cpu. The computer turns on but won't boot. Nothing appears on the monitor screen and there are no beeps. The harddrive spins, the board has power but nothing happens. When I put my old mother board back (MSI K7T Pro266A) in with the Athlon 2000+, everything works fine.
Maxtor 60 gb harddrive
512 MB SD pc2100 SD Ram
Abit 128 mb Radeon 9200SE Video card
Any suggestions?

A few things to check:
Do you have any unused stand offs in the case touching the motherboard
The XP3000 CPU is a barton core and comes in two variants, a 333FSB and a 400FSB version. Your RAM is PC2100 which with an Nforce chipset is a recipie for problems. The NForce chipset is picky about RAM and PC2100 running on a PC2700/PC3200 processor FSB probably won't work.
Also post your PSU max amps, as a +12V rail below 16A could cause problems.
Do you have a D-Bracket connected ? This is the PCI insert with 4 leds on ?

MSI K7N2 Delta ILSR Bios v.7.6 ??When??

Hello,
I just asked myself when MSI is going to publish a new Bios Update above the 7.6 for the K7N2 Delta ILSR mainboard !!! I think it's time for a new Bios update, because of the few problems with this mainboard !!!!

Quote
He has confirmed the ports are present on the board....
I have seen this in earlier Nf2 Pre Delta boards where it was there but if you had disabled it, and then flashed the BIOS, it would dissapear. The only way to get it back was to flash to an earlier version, make sure it is enabled, then you can flash to the latest.
That is why I always clear the CMOS when starting a new build. You may have a board that may have been fiddled with, believe it or not, it does happen from time to time.
Have you tried the Default BIOS Settings Option in the BIOS? Perhaps you loaded the Performance option and that is why it is hiding?
this worked, thx a lot

K7n2 delta no bios post

I had my system up and running. But was in the bios and made the mistake of putting front side bus to 166 after this it wouldn't boot to bios. Have to manually diconnect power supply as button wouldn't work. Reset pins on j10 and rebooted set bios to default it said fsb was 166 hit f10 to save settings and exit. Still couldn't get to bios so iI cleared the cemos and rebooted got to the bios and fsb was 100 I changed to 133 hit f10 to save and rebooted no bios again. Tried clearing cemos and changing jumpers around several times no luck. Took system down and removed vidio card and ram and put them back in got system to boot to bios. I hit f10 to save settings and restart (changed nothing from what it was when i got into bios) but when it rebooted no bios screen again and each time this happens I need to disconnect power from computer by unplugging as power switch doesn't work then.

okay i managed to get the computer running by removing one stick of ram. Problem i have now is it says it is only running at 1730 here are the results of cpu id. oh and i am sure i have a 2700 installed.
[ WCPUID Version 3.1a (c) 1996-2002 By H.Oda! ]
Processor #1 : AMD Athlon XP (Model 8) / 5229528F
Platform : Socket A (Socket 462)
Vendor String : AuthenticAMD
CPU Type : Original OEM Processor (0)
Family : 6 (7)
Model : 8 (8)
Stepping ID : 1 (1)
Brand : ----
APIC : ----
HT Log.CPU Cnt : ----
Name String : AMD Athlon(tm) XP 2100+
Internal Clock : 1730.72 MHz
System Bus : 266.26 MHz DDR
System Clock : 133.13 MHz
Multiplier : 13.0
L1 I-Cache : 64K Byte
L1 D-Cache : 64K Byte
L1 T-Cache : ----
L1 Cache : ----
L2 Cache : 256K Byte
L2 Speed : 1730.72 MHz (Full)
MMX Unit : Supported
SSE Unit : Supported
SSE2 Unit : Not Supported
MMX2 Unit : Supported
3DNow! Unit : Supported
3DNow!+ Unit : Supported
Host Bridge : 10DE:01E0.C1 [NVIDIA nForce2]
South Bridge : 10DE:01EB.C1 [NVIDIA nForce2 MCP]
VGA Device : 10DE:0251.A2 [NVIDIA GeForce4 Ti 4400]
Memory Size : 512M Byte
Memory Clock : ----
OS Version : Windows XP Version 5.01.2600 Service Pack 1
StdFunc 0 : 00000001 68747541 444D4163 69746E65
StdFunc 1 : 00000681 00000000 00000000 0383FBFF
ExtFunc 0 : 80000008 68747541 444D4163 69746E65
ExtFunc 1 : 00000781 00000000 00000000 C1C3FBFF
ExtFunc 2 : 20444D41 6C687441 74286E6F 5820296D
ExtFunc 3 : 31322050 002B3030 00000000 00000000
ExtFunc 4 : 00000000 00000000 00000000 00000000
ExtFunc 5 : 0408FF08 FF20FF10 40020140 40020140
ExtFunc 6 : 00000000 41004100 01008140 00000000
ExtFunc 7 : 00000000 00000000 00000000 00000001
ExtFunc 8 : 00002022 00000000 00000000 00000000
C0010015h : 00000000 040B1008 00000000 FC8CC2C0
C0010016h : 00000004 047E1018 00000000 FC8CC2C0
C0010017h : 0000000B 05685000 00000000 FC8CC2C0
C0010018h : 00000000 E0000018 00000000 FC8CC2C0
C0010019h : 0000000F FC000800 00000000 FC8CC2C0
C001001Ah : 00000000 20000000 00000000 FC8CC2C0
C001001Bh : 00000000 20031223 00000000 FC8CC2C0
C0010111h : 00000000 000A0000 00000000 FC8CC2C0
C0010112h : 00000000 00000000 00000000 FC8CC2C0
C0010113h : 00000000 00000001 00000000 FC8CC2C0
##--- Date 02/11/2004, Time 17:22:20

MSI K7N2 DELTA L BSOD Booting to DIsk/XP CDROM

Installed the MB tonight. Cannot boot to existing WINXP home. Get BSOD whel loading. Stop Error 7B. Cannot boot from XP Home CD. Some other BSOD stop error.
Bios pretty much defaults. Disables a few things like serial ports (been disabled on other MB as well).
System has been fine on SoYo Dragon Ultra Black. Installed ECS K7VTA3 yesterday. System worked OK, but decided to go to MSI today. Now, no boot.
Tried changing memory, disconnecting all but boot disk, no luck.
Any ideas?
- webpro

it will never boot if it has another chips sets ide drivers on it
you will have to overinstall at least
post psu max amps as these seem to need a lot of power
3.3 5 and 12v Power Supply Guide

K7N2 Delta w/n boot from cd-rom

Building a new system. Has 2800+ Barton CPU, 512m Mushkin PC2700 in slot 1, GeForce4 MX440 w/64m. Memorex 40 CD-R and Teac 12X CD-ROM.
Went into Bios setup fine and set req'd settings.
When trying to boot off of CDROM to install XP, Floppy makes the usual noise, DMI pool info comes up, nVidia boot agent appears after "Boot from CDROM" msg appears.
I'm getting a "PXE-EX61 Media test failure, check cable" msg, then "Disk boot failure" msg.
I've tried both cdr and cdrom drives together AND separately, but neither one works. I know the cable is good.
Also have tried using cdrom AND floppy as 1st boot devices, with same result. I've read 12+ pages of earlier posts and replies with only 1 post similar to mine. Tried hooking up only 1 optical drive and using the floppy as the 1st boot device as suggested, but no luck.
Any other suggestions?

davida62,
Try the XP CD in another comp. Make sure it is not the issue. Also you would try the drives in another comp to make sure they will boot from the CD.
When we have the answers to those questions we can proceed with the troubleshooting of your comp.
Take Care,
Richard

K7N2 Delta, Fasttrack Bios probs

Well I just put together my new PC
K7N2 Delta_ILSR
XP2800 Barton
512ddr PC2700 CorsairXMS ram
GF4TI4600 (Overclocked a little)
52x cd
plextor cdrw
60gb 7200rpm hdd
Windows XP pro
Well it all went swimmingly adn works fine. Just got to get used to XP. My problem is when it boots up it loads the Award Bios fine then after registering all the drives etc I get the following reading
Fasttrack 376(tm) BIOS VERSION 1.00.0.21(c) 2002-2005 Promise Technology
No drive attached to fasttrack controller, The BIOS is not installed.
Now i think this is somthing to do with the Sata setup. I have installed the drivers and all is ok, is this displayed purely as i dont have a SATA hdd yet? if so is there any way of making it so it doesnt appear??
Other than that I like my new system its really fast :D
Thanks for any replies in advance

Yes, its because you dont have any drives attached, this still shows even if you have installed the drivers off the floppy.
You could try what I have just done and put your main HD on IDE3, then you still have 4 IDE connections to use as you please.
dave

[nForce] MSI K7N2 Delta ILSR; bios, neither windows recognize IEEE1394

Hello,
Since 2 years I have used a msi motherboard. Now since I dont have IEEE1394 of an external card anymore (Audigiy), i tried to connect my digital camera with the IEEE1394 to the motherboard. Rebooted my pc, windows doesnt recognize new hardware. i'm going to look in the bios, and see that my bios (bios 7.8) is different from the one explained in the manual (see pic). I tried to downgrade my bios to 7.2, to know if it is the 7.8 version that has the problem. but it was the same, no option for IEEE1394.
Normally have you this:
But I dont see this option for the IEEE1394 in my bios....
Thx in advance for helping me

Quote
He has confirmed the ports are present on the board....
I have seen this in earlier Nf2 Pre Delta boards where it was there but if you had disabled it, and then flashed the BIOS, it would dissapear. The only way to get it back was to flash to an earlier version, make sure it is enabled, then you can flash to the latest.
That is why I always clear the CMOS when starting a new build. You may have a board that may have been fiddled with, believe it or not, it does happen from time to time.
Have you tried the Default BIOS Settings Option in the BIOS? Perhaps you loaded the Performance option and that is why it is hiding?
this worked, thx a lot

K7n2 delti Ilsr Bios update question

Well bios updates fix these ram issues? I have Kingston hyperx 3500, was on the ok list for ram, dont thank it is now. ;(
MICRO-STAR k7n2Delti ILSR latest bios and drivers
AMD 2800+barton
Fx5900 Gainward videocard
2 512 sticks of Kingston hyperX 3500 Inslot 2&3 at 2222
antec pp400watt Ps

Yes, I did mean the CPU. Corrected it now .......
Thanks, I've done that and it's now showing 1800. Much easier than updating the BIOS.
My temperatures have gone up a bit, though. CPU is now 47C (was 44C) and system is 37C (was 35C) in PCAlert4, and I'm only on the net and playing mp3s, so it's not exactly hard load!!. Is this OK? I really worry about overheating since my old mobo was unstable at lower system temps than this.
Louise

K7n2 delta series: bios settings & FSB

Hello! All
Happy Easter holidays!
Currently, I have my board fsb settings at 133 mhz and have an AMD 3000 Athlon, my question is: What settings should I have my FSB settings on? I would like to maximize my bios settings and I feel 133 mhz I am not maximizing system performance. Any help/direction would be appreciated.

ReneH,
Your min FSB should be 166Mhz. Which flavor 3000+ do you have, since I think that one came in both 166Mhz (2.16GHz) and 200Mhz (2.1GHz) FSB's.
Take Care,
Richard
P.S. But with no specs on your comp and my Chrystal Ball in the shop for repairs, I can only take a spab in the dark.

K7n2-delta LAN & bios

ANyone else having trouble connecting the cat cords to the on-board lan jack? I used homemade and store bought cat5 cable. both have world standard rj-45 plug. does not fit into the on-board LAN jack. The notch on the top is too big for the on-board LAN jack. so i am left scratchign my head.
Also, I can seem to utilize the MSI features like the live update 2. I will up date the bios but it only install 33% and then freezes on all updates thru :live updates 2" anyone else having trouble?

Brink,
Not too sure about your NIC connectors ?(
I would flash my BIOS the old fashioned way using a bootable floppy containing the flash program and the bin file.
Good Luck

K7N2 Delta Post Bios Boot faliure

Similar Messages

Maybe you are looking for