K7N2 Delta problem after flashing from 5.0 to 5.3

I was using my K7N2 Delta nicely but after flashing the BIOS from 5.0 to 5.3 in LiveUpdate3 (all OK) and then when LiveUpdate ask to reboot... GOOD BYE!
When bootin the D-lights show that I have a processor damaged or not intalled properly (two red light up, and two green down...).
My processor is an Old Tbird 1.2 Ghz with 100FSB.
The question is: Why the mother stops recognicing the processor if before flashing BIOS worked nicely?.
J10 and J11 jumpers:
When I opened case to check out, I had the green J10 and J11 jumpers closed in the mother. The J10 was in safe mode, and the J11 jumper was closed...(133FSB-166FSB??).
I only have another athlon 1.1 ghz FSB100 processor to test the mobo, but I don´t want to take the risk of burn that one two (if is that the problem, of course).
So... I want to know how can I reflash the bios back (I have the old BIOS in a backup floppy disk, of course)... or if anyone else have the same problem as me....
Thanx a lot guys, and please help me... I´m very sad by now... because I don´t know how to get my computer to work.
Jose.
(from Argentina)

Garry,
Just add
group.Administrators=system
in your filerealm.properties file to login into console.
Hope it helps,
-satya
garry payten wrote:
I am migrating from 5.1 to 7.0 on Solaris. I was able to run the conversion of the weblogic.properties file to config.xml, I was also able to start the new admin server, but I was not able to log in to the console. I get the following error:
Authentication Denied
The username or password has been refused by WebLogic Server. Please try again.
I verified that the WL_USER and WL_PW were correctly set in the startscript and that the system password was set in the config.xml. Any hints? Thanks

Similar Messages

Problems after updating from Mavericks to Yosemite.

Hello everyone.I have noticed some battery problems after updating from Mavericks to Yosemite like no charging at all (but the orange led was on )and not able to fully charged.I solve them with SMC reset and PRAM reset.Furthermore, battery discharges faster than before and its really annoying.Now I have notice that the upper right corner of my mac is getting hot.I'll appreciate any help
MacBook Pro (Retina, 13-inch, Late 2013

Try these in order testing your system after each to see if it's back to normal:
1. a. Resetting your Mac's PRAM and NVRAM
    b. Intel-based Macs: Resetting the System Management Controller (SMC)
2. Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
3. Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
4. Reinstall Yosemite: Reboot from the Recovery HD. Select Reinstall OS X from the Utilities menu, and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
            because it is three times faster than wireless.
5. Reinstall Yosemite from Scratch:
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
How to Clean Install OS X Yosemite
Note: You will need an active Internet connection. I suggest using Ethernet if possible
            because it is three times faster than wireless.

K7N2 Delta problems

Hey all..having a huge problem with my computer and have no idea what's going on.....when i try to reformat, i am getting errors with blue screen. errors are as follows: Page_Fault_In_Non_Paged_Area followed by the stop error numbers
Driver_IRQL_Not_Less_Or_Equal
IRQL_Not_Less_Or_Equa
as well as a wait or yield error in a DPC routine
Now, when i reset the bios, it will reformat and install windows, but I never had to do this before. Also, when i am up and running, i am getting both crash and reboots, as well as lock-ups. Again, never happened before a month or so ago. Does anyone have any ideas? I don't know if this is a PSU issue, a BIOS issue( I just updated to the latest BIOS version, but after all the problems), a heat issue or what. Here are my specs:
MSI K7N2 Delta
Athlon XP 3200+
2x512 mb of DDR333 RAM
usually use Radeon 9700 Pro, but am currently forced to use FX 5200
WD 60 gb hdd with 8 mb cache
AOpen 300 watt psu
3.3v - 20.0A 5v - 30.0A 12v - 13.0A
any help would be appreciated gang...have a good one !!

Flash the bios back to B30. Much more stable than B40. B40 are really buggy same as the beta one. Good Luck.
Tbred B 2400 (180 x 13.5) 2.10 volt
MSI K7N2 Delta2 LSR
2 x 256 PC2700 Kingston Value RAM
Powercolor Radeon 9600XT 600 core 800 memory
450 Icute PSU.

Sound Problems after Flash 11.3 Update

This reply is to the post by Ortho_Fan, number 28, which references a Firefox forum and "Firefox Hates New Update." This thread is specifically about problems that Flash 11.3 is causing with Firefox but the problem isn't with Firefox, it is with Flash Player 11.3.
I have no sound with Firefox, Chrome or Safari. I do have sound with IE9 but some people do not.
See these and probably other threads:
No sound in flash
http://forums.adobe.com/message/4483563?tstart=0
Problem with sound after update
http://forums.adobe.com/message/4483038

I've branched this discussion into it's own thread, because the issue you're describing is different than the issue from the previous thread, which was related to a specific crash instance. We'd like to keep the threads focused on particular issues to help both investigate and collate the information coming in, and to aid in discovery for people that are experiencing similar issues. A single thread with a dozen issues is far less useful in either regard.
For the sound issue you're experiencing, I would recommend that you follow the advice in the threads you've referenced above.
Flash Player 11.3 included new sound enhancments to facilitate support for low-latency audio, to facilitate more repsonsive sound in complex Flash games. While we try to test a wide array of hardware, and conduct months of beta testing, it's impossible to hit every device, OS, browser and driver combination.
Please ensure that you have the lastet drivers installed for your sound card/chipset. If the problem persists, please post details of your configuration to that forum thread so that we can track down that hardware/driver combo and investigate the problem.
As a workaround, you may wish to roll back to Flash Player 10.3, until a new version is available. Flash Player 10.3 contains up-to-date security patches (we maintain one major version back for Enterprise), and will revert the sound change that is causing problems for you.
http://www.adobe.com/support/flashplayer/downloads.html
Thanks!

K7N2 Delta problem

Hey all,
Ive used a K7N2 Delta board for about a year with now probs at all... until now. Couple days ago i decided a new case was in order, i purchased case went home and transfered all the components over, as it was i was changing a few parts too so i decided to go with a rebuild followed by a format/reinstall to start a fresh.
I put pc together, reinstalled windows xp pc booted fine, then i spent the next 30 mins or so installing all the programs i normally use. This pc is 1 of 2 i use and is lower spec as i only use it for work purposes, i use 2 graphice cards in it for dual monitor, a geforce mx 400(agp slot) and a tnt 32 something (pci slot) after doing a bit of installing i went to the bios, the pc was booting using the lower card as pri display, all i wanted and all i did was change the first display in the bios to AGP. I hit F10 to save and restart... and nothin pc hasnt done a thing since.
I get no warning beeps at all when i try to power up, although the power lights are on and cpu/system fans run. I checked the D-bracket, the code it goes to as soon as you power up and it stays there is'Initializing Hard Drive Controller' I aint no wizard when i come to fixing or building pcs but as a DIY'er i still think i hold my own, ive done or tried everything i can think off... clear cmos, change battery, remove components, change components, ive tried to boot with nothin connected to everything connected, board wont even beep, just get same d-bracket message everytime, im under the impression that a new board is needed but i thought i'd post here in the slight chance someone might have a idea, or maybe able to tell me something i havent thought of.
thanks

Ive done everything described above, and redone it just to make sure lol Not being one to quit easily ive been messing around with the board, now im starting to think there maybe some life left in it after all, first off if i remove the memory it now signals the warning beep, something i wasnt doing, also the d-bracket code has changed, its now hanging on 'memory detection test' i know this memory is good, plus ive tried another module in with same results. Yet another strange thing, when i try to boot up with a xp2000 (also tried a xp1700) within a few seconds it shuts down, but if i try my 1300 duron and change mhz to suit even though im not getting anywhere near actually booting, it atleast stays on giving the memory code. Ive been told, dont know if this is right, that if i take the bios chip out of the board for 24 hrs it will reset the bios back to factory setting (bios has been flashed a couple times but not recently) any one know if this might help, or even if this will work? This board acting strange, bit of a mystery goin on ere lol any more suggestions?
thanks again
shaun

Problems after upgrading from 10.2.3 to 10.2.8

After upgrading from 10.2.3 to 10.2.8, itunes "unexpectedly quits" when I try to purchase a song, and safari "unexpectedly quits" when I visit certain websites. Before upgrading, no such problems.

Hello rick,
First of all, welcome to the Apple discussions.
* How did you upgrade the OSX 10.2.3??
* Did you use the combo update?
* Did you run the dick repair permissions before an after
Here is the Combo Update for OSX 10.x
Combo Update
An here is how you use the disc repair permissions
About Disck Repair Permissions
Applications Quits
Let me know if so ...
Discussions is a ongoing process. Hope to see you around anytime you need us, or can offer help to others.
Dimaxum <]:~))

Sound Problems After Restore from Hibernate Using uswsusp and pm-utils

I see mention of using /etc/pm/config.d/module to recycle certain kernel modules during suspend. Do I need to suspend all modules?
**** List of PLAYBACK Hardware Devices ****
card 0: MID [HDA Intel MID], device 0: CS4206 Analog [CS4206 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: MID [HDA Intel MID], device 1: CS4206 Digital [CS4206 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
[aj@mbp62 ~]$ lsmod | grep snd
snd_hda_codec_cirrus 8790 1
snd_hda_intel 36904 1
snd_hda_codec 149633 2 snd_hda_intel,snd_hda_codec_cirrus
snd_hwdep 6340 1 snd_hda_codec
snd_pcm 77709 2 snd_hda_codec,snd_hda_intel
snd_page_alloc 7242 2 snd_pcm,snd_hda_intel
snd_timer 18726 1 snd_pcm
snd 59173 8 snd_hwdep,snd_timer,snd_pcm,snd_hda_codec,snd_hda_intel,snd_hda_codec_cirrus
soundcore 5450 1 snd
[aj@mbp62 ~]$ cat /etc/pm/config.d/module
SUSPEND_MODULES="bcma b43 snd_hda_intel"
SLEEP_MODULE=uswsusp
Any pointers?

This morning, I rebooted for half an hour without success:
After resume from hibernate, most of my machine froze like described above.
After first reboot, it worked for 1 minute, then I had a full freeze (nothing worked... no mouse, no normal keys, no magic keys, screen frozen...)
After second reboot, my wifi adapter was gone. It showed up in lspci and looked like this:
04:07.0 Network controller: Atheros Communications Inc. AR5416 Wireless Network Adapter [AR5008 802.11(a)bgn] (rev 01)
Subsystem: Atheros Communications Inc. Device 3071
Flags: 66MHz, medium devsel, IRQ 22
Memory at feb70000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [40] #80 [0000]
...but not in ifconfig. I found the following in dmesg:
[ 7.106070] ath: phy0: address test failed addr: 0x00008000 - wr:0x00080008 != rd:0x00000008
[ 7.106181] ath: phy0: Unable to initialize hardware; initialization status: -19
[ 7.106287] ath9k 0000:04:07.0: Failed to initialize device
Problem persisted over 10 poweroffs/reboots (also hit the "on" button a few times with the pwoer cable disconnected, trying to make it "reset" or something. Did not help this time, might have been coincidence the last time that worked.

Problems after resuming from hibernation

I’ve been getting horizontal lines and sound distortion after resuming from hibernation. Has anyone had similar problems or found a solution for this yet? I’m on Lion OS X 10.7.3.

Rorschach wrote:What freezes? Just X or the whole kernel? Can you ssh to your machine?
Now it doesn't freeze anymore. I really don't know what the heck is going on on my machine.
Next time that the machine freezes I'll try to ssh to it. Thank you for pointing this out.
Last edited by ArchArael (2010-03-26 15:56:17)

Anyone's MacPro have problems after waking from sleep mode?

After waking from sleep, my MacPro 2x2.4 Quadcore Intel Xeon freezes in several applications that had been running before sleeping. Mail and Firefox both get into endless loops trying to download data and will not force quit. Pulldown restart and shut down do not function when this is occurring. Must shuyt down manually from box and start again. Everything works fine again until it goes to sleep again.

Start by swapping the keyboard. You don't need to spend a fortune, and handy to have spare. USB cables can be bad even new.
When I had some problems Apple wanted to blame the mouse, keyboard, cable, but in the end I found
A. run Disk Warrior
B. Corrupt pref or conflict with version of Hardware Monitor and other background tasks

Problems downloading Flash from the CS3 CD.

So I just recently got CS3 Design Premium for a job I'm working on.
I downloaded the trial for Flash CS3 about a year ago separately from the design premium and left it unregistered.
So when downloading the Design Premium it did not reinstall Flash CS3.
When I registered all of the products Flash CS3 remained unregistered.
I uninstalled Flash and tried to install it from the Design premium CD.
Whenever I attempt to download Flash from the CD however, it ejects the disk after a minute or 2 and asks me to insert a disk for Illustrator, however there is only one CD, and if I put the CD back in it ejects.
Help, what do I do?
Do I deactivate the programs and install it all over again, and if so how do I deactivate the applications?
Any help would be appreciated.

I have no idea what that means but try closing the App Store, and reboot your iPad. See if that helps.
Go to the home screen first by tapping the home button. Double tap the home button and the recents tray will appear with all of your recent apps displayed at the bottom. Tap and hold down on any app icon until it begins to wiggle. Tap the minus sign in the upper left corner of the App Store icon. Tap the home button.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

Performance problems after Update from 7.6.00.37 to 7.6.03.15

Hi,
after the Update from 7.6.00.37 to 7.6.03.15 in our live system we noticed a lot of performance problems. We have tested the new version before on our test system, but there don't noticed effects like this.
We have 2 identical systems (Opteron 64 bit, openSuse 10.2) with log shipping between them. We updated first the standby system, switched from online to standby (with copy of cold log) and started the new server as online system. After that we run a complete backup (runtime: 1 hour) for starting a new backup history and for activating autolog. Then
With the update we changed USE_OPEN_DIRECT to YES, but the performance of the system was very slow afterwards. After the backup it remains at a high load average (> 10, previous system had about 2-4), with nearly 100% of CPU usage for the db kernel process.
Next day we switched USE_OPEN_DIRECT back to NO. The system first runs better, but periodically rises up to a load average of 6 and slow down the performance of various applications (somebody says about 10 times slower). Here we also noticed a high usage (now 200-300%) of the db kernel process.
Our questions are:
1. Has something basically changed from 7.6.00.37 to 7.6.03.15, so that our various applications (JDBC, ODBC and Perl/SQLDBC partially on old linux systems with drivers from 7.5.00.23) don't reach same performance as before?
2. Are there any other (new) parameters, which can help? Maybe reducing MAXCPU from 4 to 3 for reserving capacities for the system (there is only one maxdb instance running)?
3. Is the a possibility to switch back to 7.6.00.37 (only for worst case)?
I have made some first steps with x_cons, but don't see any anomalies on the first look.
Regards,
Thomas

Thomas Schulz wrote:>
> > > Next day we switched USE_OPEN_DIRECT back to NO. The system first runs better, but
> >
> > What is it about this parameter that lets you think it may be the cause for your problems?
> After changing it back to NO, the system runs better (lower load average) than with YES (but much slower than with old version!)
Hmm... that is really odd. When using USE_OPEN_DIRECT there is actually less work to do for he operating system.
> > > Our questions are
> > >
> > > 1. Has something basically changed from 7.6.00.37 to 7.6.03.15, so that our various applications (JDBC, ODBC and Perl/SQLDBC partially on old linux systems with drivers from 7.5.00.23) don't reach same performance as before?
> >
> > Yes - of course. Changes are what Patches are all about!
>
> Are there any known problems with updating from 7.6.00.37 to 7.6.03.15?
Well of course there are bugs that have been found inbetween the release of both versions, but I am not aware of something like the performance killer.
We will have to check this in detail here.
> > > I have made some first steps with x_cons, but don't see any anomalies on the first look.
> >
> > Ok, looking into what the system does when it uses CPU is a first good step.
> > But what would be "anomalies" to you?
>
> Good question! I don't really know.
Well - then I guess 'looking at the system' won't bring you far...
> > Do you use DBAnalyzer? If not -> activate it!
> > Does it gives you any warnings?
> > What about TIME_MEASUREMENT? Is it activated on the system? If not -> activate it!
>
> OK, that will be our next steps.
Great - let's see the warnings you get.
Let us also see the DB Parameters you set.
> > What parameters have changed due to the patch installations (check the parameter history file)?
> >
> > What queries take longer now? What is the execution plan of them?
>
> It seems to happen for all selects on tables with a lot of rows (>10.000, partially without indexes because automatically generated). With the old version we had no problems with missing indexes or the general performance. Unfortunatly it is very difficult to extract some sql statements out of the JBoss applications. But even simple queries (without any join) runs slower, when the load average rises over 4-5.
Hmm... the question here is still, if the execution plans are good enough to meet your expectations.
E.g. for tables that you access via the primary key it actually doesn't matter how many rows a table has (not for MaxDB at least).
> > BTW: how exactly do the tests look like that you've done on the testsystem?
> Usage over 6 weeks with our JDBC development environment (JBoss), backup and restore with various combinations of USE_OPEN_DIRECT and USE_OPEN_DIRECT_FOR_BACKUP.
Sounds like the I/O is your most suspect aspect for overall system performance...
> > Was the testsystem a 1:1 copy of the productive machine before the upgrade test?
> No - smaller hardware (32 bit), only 20% of data of the live system, few db users and applications.
>
> > How did you test the system performance with multiple parallel users?
> Only while permanent development with the 2-3 developers and some parallel tests of backup/restore. Unfortunately no tests with many users/applications.
Ok - so this is next to no testing at all when it comes to performance.
> An UPDATE STATISTICS over all db users seems to change nothing. At the moment the system remains markedly slow and we are searching for reasons and solutions. Another attempt will be the change of MAXCPU from 4 to 3.
Why do you want to do that? Have you observed any threads that don't get a CPU because all 4 cores are used by the MaxDB kernel?
regards,
Lars

Thinkpad G40 keyboard problems after updating from W98 to W7

Hi community users.
I'm new here with a, for me, typical problem.
I’m having a problem with my Laptop keyboard IBM ThinkPad G40, type: 23884SG, Windows 7.
Since I updated from Windows 98 to Windows 7 the keyboard definition is wrong. I’m not able to find the right configuration of it on base of the standard list of country and language definitions in W7.
Who can help me with this.
I already installed some drivers from the Lenova site but nothing seems to help.
So the problem is that I can’t find the right service from the country and language menu to the keyboard in W7.
All suggestions are very welcome.
Thanks in advance,
Dirk
Moderator Note; s/n & UUID edited for members own protection

Hi Vince,
Thanks for your response to my problem.
Problem isn't the choice of the specific language. The problem after the update is that I'm not able to choose the right combination of language and the type of keyboard selection in Windows 7. The selection list is long: from South-Africa to Sweden.
Although most of the characters on the keys on the lower part of the keyboard correspond with the ones on the screen but especially the keys on the upper part don't.
So I'm searching to a correct selection of the combination language and specific type of keyboard. Or there must be some driver witch can be download.
Looking forward to the feedback.
Kind regards,
Dirk

Problems after migration from CS5 to 5.5 with Blackmagic Card

Hello forum,
we have an problem after an optimal migration from cs 5 to 5.5 projects.
different: there is an bm hd extreme 3d card in the system.
We are aware of the issue that there has to switch to BM player an the Timleinl settings to BM
But there is still a problem: we are not able to view the ingested material in the source viewer,
because there is another overlay - form the background or sometheing else - see attached photo.
We add new drivers for graphics/BM and patches for CS 5.5
None of these problems by creating new projects.
Also the applications also hangs after we try to close,
many thanks for your answers - Sven.

No reason to ask the same question twice. Just be aware that there are German forums as well.
Your problem is probably in the BM drivers.

XFX GeForce 7600GS 512mb AGP with MSI K7N2 Delta Problem

Hi, I have been searching in everyplace and still I havent find a solution.
I have the XFX GeForce 7600GS 512mb AGP card.
I use the MSI K7N2 Delta.
My Processor its the AMD 2600+ XP
my PSU its a 420watt
my RAM its 2gb DDR 400
I made everything in the bios, didnt work.
I updated the lastest drivers and bios, didnt work.
I went to a friend house, he use a P4 motherboard with 500watts. Worked, PERFECTLY.
I changed the card once (the first one didnt worked at all) but this one worked...
now the question is:
HOW I MAKE IT WORK IN MY PC ?????????
Can anyone help me? I dont wanna sell it to a friend for only 60$ (that the only costumer I have found for the card in Panama)

Heh I had problems with trying to see again was what happening in my PC but yesterday....
Ok I went to my friend house, we used the card with his 350 watts 15A in the 12V+ and it worked.
Then we tried to install the PSU but I dont know why its 4pin was incompatible with mine....
Well heres the important part: I went to a local Computer Store where they repair too and with another more powerfull PSU in my PC and the card didnt worked for seconds, but the guy played a little with my Ram and he noticed that its posible to that be the problem. Remember that my ram its a Kingston 400DDR 2X1 Gb running in the purple and the green slots of the mobo. when we changed them to both purples slots of the mobo the PC dosent work and make a the beep sound. I have the braket in my computer and it showed a red dot here: GR
GG
Gonna search the manual to know what that means.

N95 - Problem after flashing F/W No 12.0.013

Hello,
After flashing F/W 12 to my N95 / (RM-159 07.01) through Nokia Software Updater, I found that the phone was loaded with a different set of available languages. As a result, Greek language was no more available.
Before the update, the phone was operating with 'Automatic' menu language (resulting to Greek) and English writing language. It's an unbranded model.
Note: A month ago, I had upgraded another (unbranded) N95 with no problem (Greek language was existing also after the ugrade). However it had different settings: Menu in English and Writing in English.
Can anybody help to recover the lost set of languages in the last N95?
Thank you

Very strange.
I would suggest that you contact your network and tell them that your sim isn't working properly but don't tell them what caused it (so they can't blame it on you).
They should replace your sim free of charge as it's not your fault.

K7N2 Delta problem after flashing from 5.0 to 5.3

Similar Messages

Maybe you are looking for