K7n2 ide problem

i recently updated my system drivers for my k7n2 delta-ilsr to stop it crashing, it did stop crashing but now it doesn't recognise either of my cd drives, both on secondary, recognises my hard drive fine, in device manager it says that the primary and secondary ide controllers are faulty, any sugestions?

i think its running off the drivers that came with the most recent system drivers, so probably, i would install the old ones from the cd if it wern't for the fact that i cant use my cd drives. do you know where i can get some other drivers from?

Similar Messages

K8N Neo4-FI Major IDE-problems (Only Pio on some disks)

Just registered so hello everybody!
I just got me a new rig which is seen in my sign. It took me a long time to figure out that you couldn't install Win on the Sata drive without having all of the IDE disks offline, but eventually I think I read that somewhere here and made a successful installation of the incredible Win XP .
When I was finished with installing I connected all the IDE-drives (Ch01: Seagate 160GB as master and Seagate 300GB as slave; Ch02: Seagate 80GB as master and NEC DVDRW as slave - all jumpered properly) it took me an even longer while to figure out that IDE wouldn't work at all with the supplied (and/or downloaded) Nvidia drivers. But I read that somewhere here too.
Now my rig is pretty much set up, but not working as it should - and when you've just spent some 800 Euros on a new comp you don't want to engage in compromises.
Problem is that having the IDE drives connected (regardless of configuration) makes the boot time incredibly long, while with only the SATA drive connected it is very rapid. But the problems doesn't stop there...
The slave on Channel 1 (the 300GB) and the master on Channel 2 (the 80GB which is not on the controller card) are both ran in PIO mode, and this seems impossible to change. I have read a lot about IDE problems with the Nvidia chipsets on this forum including what is in the FAQ and other places about how You should config your IDE drives to have them work properly but nothing seems to work. I'm beginning to consider sending MSI an angry e-mail telling them what I think about this bullsh*t.
Does anyone have an idea apart from what has been written and explained already on this forum (I'm pretty certain that I've read it all).
Best,
C

Quote from: c-boy on 24-March-06, 04:45:26
I'm upping this a little...
I narrowed the problem down, and I'm getting desperate now. Unfortunately, the MSI support hasn't been of much help so far.
I've read and read at all sorts of forums and the ones to blame are NVIDIA, since many people regardless of their board brand have issues.
However, I have now connected the 300GB with NVIDIA drivers, and it is found, and present in the disk manager, but no data is found. It is also marked as "unallocated" in the disk manager. Since I'm a musician and that disk has a lot of samples and music I need I don't wanna format it although I may be able to get all data back if I do.
When the drive is connected with the intergrated WinIDE drivers the data on it is found but it doesn't perform in anything but PIO mode.
I've had the new system online for almost a month now, and my Win installation is getting set-up to what I need, therefore I don't really want to reinstall. But, do you folks think that it would help to reinstall Windows? And not go anywhere near the NVIDIA drivers again.
I'm suspecting that they f***ed everything up at first but I'm not sure. I'd be ripping my hair off if I reinstall Windows and the problem remains.
I also invested in hi-quality ATA cables from Thermaltake recently, no difference though.
Any input (on topic) would be appreciated.
Regards,
C
What a coincidence, I happen to be having a similar issue. My sec HDD (maxtor) appears on Computer Managment/Disk Managment as "unallocated" as well.
I have tried any trick that I know of without any success. Reading your post gave me the idea of buying an expansion card. However, I refuse to spend the money on something that should work in the first place.
I strongly belive that the issue here lies on the mobo itself, as I have been able to get it to work on only one IDE conector.
Hey let me know if you ever manage in getting it to work.

K8N Neo Platinum IDE problem

I got everything installed just fine and all is well booting into windows. I then install all the chipset drivers on the cd and reboot. The next time I put a cd in my rom to install a program it takes forever for it to read the cd and also windows gets really slow. I spent a while trying to figure out what was wrong and finally reinstalled windows again. And again same thing, as soon as I install the chipset drivers my Rom goes wack and windows is super slow. So I uninstalled the IDE drivers that the disk installed and let windows install its own drivers and WAAA LAAA problem solved. By the way I use a sata hard drive and the only thing on the ide is my dvd burner. Thats the only optical drive I have. Anybody else have this problem? I even tryed the new 5.10 drivers and same thing.

I've had ide problems with the nforce ide drivers. The windows set always has worked for me. I had to try a few different versions and ended up having version 5.10.2600.412 work for me.
If you are deadset on nforce drivers then that may help if you try other versions but if not the windows drivers seems to not have any problems.

K7N2 Delta problems

Hey all..having a huge problem with my computer and have no idea what's going on.....when i try to reformat, i am getting errors with blue screen. errors are as follows: Page_Fault_In_Non_Paged_Area followed by the stop error numbers
Driver_IRQL_Not_Less_Or_Equal
IRQL_Not_Less_Or_Equa
as well as a wait or yield error in a DPC routine
Now, when i reset the bios, it will reformat and install windows, but I never had to do this before. Also, when i am up and running, i am getting both crash and reboots, as well as lock-ups. Again, never happened before a month or so ago. Does anyone have any ideas? I don't know if this is a PSU issue, a BIOS issue( I just updated to the latest BIOS version, but after all the problems), a heat issue or what. Here are my specs:
MSI K7N2 Delta
Athlon XP 3200+
2x512 mb of DDR333 RAM
usually use Radeon 9700 Pro, but am currently forced to use FX 5200
WD 60 gb hdd with 8 mb cache
AOpen 300 watt psu
3.3v - 20.0A 5v - 30.0A 12v - 13.0A
any help would be appreciated gang...have a good one !!

Flash the bios back to B30. Much more stable than B40. B40 are really buggy same as the beta one. Good Luck.
Tbred B 2400 (180 x 13.5) 2.10 volt
MSI K7N2 Delta2 LSR
2 x 256 PC2700 Kingston Value RAM
Powercolor Radeon 9600XT 600 core 800 memory
450 Icute PSU.

K7N2 sound problem

hello.
I have a serious problem with my MSI K7N2-L mobo. Ín games i get this crackling sound (clicks och pops). At first I thought it was because of my sb Live card so i bought a audigy2. and guess what? the crackling sound is is still there... ;( I have even tried the integrated AC97 soundcard but I get the same crackling sound...
and now what, is this a hopeless situation? I think my mobo has some kind of failure. What do You think?
pls help me ?(
Win XP Pro
AMD 2400
512mb ddr ram
Soundblaster Audigy 2
Mobo: MSI K7N2-L nForce 2
*New drivers - all devices*

0 system timer
1 keyboard
3 com2
4 com1
6 floppy
8 system CMOS/real time clock
9 ACPI compliant system
12 mouse
13 numeric data processor
14 primary IDE-channel
15 secondary IDE-channel
10 NVIDIA nForce PCI system management
10 USB
17 Crative SB Audigy
18 IEEE 1394
19 NVIDIA GeForce4 Ti
20 Standard OpenHCD USB
21 NVIDIA nForce MCP
22 Standard OpenHCD USB

K7N2 Temperature Problems

I'm having some small temperature problems with this board.
Here are the temps
CPU: 45-60 (normal-load)'c
Case: 38-45
Chipset: 42-47
The CPU isn't too bad, although I do see some strage fluctuations, like while writing this, its went upto 57 and then the next reading dropped to 47???
I have a laser digital thermometor which obviously can only scan temps external of the heatsinks, but it is accurate, and it does report similar temps.
My main worry here is the case temperature.
Here is my setup
K7N2 Delta 2
athlon 2.5 @ 2.2Ghz
1GB corsair (512*2)
Nvidia 6800GT 256MB DDR3
DVDRW
DVDROM/CDRW
120GB SATA HDD
500WATT PSU (which is heating up a little and could be a cause of this)
3 case fans
thermaltake volcano 12+
I've tried not clocking but there is little difference, room temps are at 20-25'c.
The heatsinks near the chipset seems to be getting rather hot also.
It doesn't have any stability problems. Its fine with games, no slowdowns. but its just the temps.
Can someone please compare my temps with the same board, just so I can get an idea.
Thanks in advance

I definitally need something black...
Otherwise it'd be a little out of place!
In all honesty I wish I could buy things from newegss. they seem to have a great range and nice system.
In the UK i'm reverted to buying from EBuyer (despite their poor customer services!), there prices are the cheapest although much dearer than the US...
http://www.ebuyer.com/customer/products/index.html?rb=3549119343&action=c2hvd19wcm9kdWN0X292ZXJ2aWV3&product_uid=54146
Its way out of my price range. I have £50ish set aside for it, and I'm looking at these at the moment all from overclockers (seem to have best range, not price) :
Sunbeam Samurai:
http://www.overclockers.co.uk/acatalog/Sunbeam_cases.html
Coolermaster Centurion 5:
http://www.overclockers.co.uk/acatalog/Online_Catalogue_Coolermaster_Cases_126.html
Antec SLK3700BQE Black Quiet Midi
http://www.overclockers.co.uk/acatalog/Antec_Cases.html
If anyone from the UK can reccomend somewhere that would be sweet!
I'm looking at:
Dabs
Ebuyer
Eclipse Computers
Redstore
Simply Computers
Aria.co.uk
Please I need more!

[nForce] K7N2 SATA problem

Have looked through these forums and havent found my problem posted yet.
I have a new seagate 160gig SATA2 hd and the MB will not see it on a reboot and system hangs. If I turn off the power the HD is seen and works fine (have installed xp) but when the computer is restarted the drive is gone as well as the rest of the IDE devices are detected realy slow then it stops when trying to detect the SATA drive. I have tried several things so far and dont know the direction I should take now.
#1 tried drive in both SATA1 and 2 ports.
#2 removed IDE HDs
#3 Differnt power connector.
System specs:
K7N2 Delta2 LSR V11.5
AMD XP3200
2 512meg DDR400
nvidia fx5700 vc
SB audigy
DVD ROM
CD-RW
WD 60gig
Seagate 30gig
enermax 475w PS
3.3v 34a, 5v 40a, 12v1 16a, 12v2 15a
If you want more info just let me know

Wonkanoby had a very consise description on how to get SATA2 working on "older" systems, thought it might have been for VIA mobos. Not sure. I'll make a search, and don't hang up.
--------------intermission--------------------------
Yes, apparantely only for VIA boards:
https://forum-en.msi.com/index.php?topic=84984.0
http://wdc.custhelp.com/cgi-bin/wdc.cfg/php/enduser/std_adp.php?p_faqid=1337&p_created=1112379341&p_sid=MZ4D46Jh&p_lva=&%20p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX<br%20/>%203Jvd19jbnQ9NiZwX3Byb2RzPTIwMyZwX2NhdHM9MTMwJnBfcHY<br%20/>%209MS4yMDM7Mi51MCZwX2N2PTEuMTMwOzIudTAmcF9zZWFyY2hfd<br%20/>%20HlwZT1hbnN3ZXJzLnNlYXJjaF9mbmwmcF9wYWdlPTEmcF9zZWF<br%20/>yY2hfdGV4dD1qdW1wZXI*&p_li=&p_topview=1
It is strange that boot is prevented, I agree. Is Other devices (or a similar title) first in the boot sequence?

[nForce] K7N2-ILSR Problem with FSB

i am having trouble with the above
if i set the FSb at anything over 167 in the bios the system will boot as far as windows then hang at the welcome screen,
if the FSb is set at anything below 167 everything seems fine
specs of the pc are
AMD 3200+ athlon xp
MSI K7n2-ILSR
Tt Volcano7
2x512 MB PC3200 Geil Duel channel
Nvidia GeForce2 mx400
1x160GB maxtor sata Primary Master
Sony DVD RW DW-U10A Secondary Master
TDK CDRW480 Secondary Slave
Realtek AC97 Onboard Audio
650w poewe supply with triple fans
Windows XP SP2
ps memory runs fine at 2*200 no problem

Does problem exist when running fsb:dram at 1:1?
same problem whichever ratio is set
List max amps for psu for 3 different rails; supply make/model also; 650W sounds impressive but it might be a Q-tec
it is a q-tec supply ? i gather there is a known problem with these ?
maxtor sata on IDE master? typo?
OOps Typo maxtor sata on sata port
Is this new system? Or added new component
system previously had an amd 1800 chip and 333memory and ran stable
Is cpu/heatsink correctly greased/fitted?
cpu is seated corectly and thermaltake silver heat paste used
What are temps in bios for cpu/system?
CPU running at 44 degrees chassis running at 34 degrees

K7T Turbo LE IDE problem?

Hi,
I'm stuck here. I have an AMD Athlon 1400/266 (T-bird) running on the K7T Turbo Limited Edition mainboard, BIOS version 3.6. 512 MB PC133 SDRAM. 2 Maxtor HD's. My system is about 2 years old.
In the last 2 months, the following has started to happen:
Occasionally (say, 1 out of 10 attempts), my PC won't boot (DISK_BOOT_FAILURE). I know this in advance because when it happens, it gives two short beeps when powered up (can't find the meaning of them :O ).
The problem is: sometimes the Primary Master is gone ("none"), but other times, it's the primary slave. In that case, the PC will boot but behaves very strange once WinXP is started. And sometimes, both master and slave show up as "None" ?(
The optical drives on IDE2 are detected at all times.
D-Bracket is all green. I reseated the IDE cable with no result. Tested both the Maxtor HD's, no errors.
So, what now? Any ideas?
Thanks,
Dennis

Just came back from my holiday so I ran some more tests.
First, I checked the drives one at a time using the PowerMax utility. 81GB slave is fine (tested alone).
40GB master is fine 9 out of 10, 10th time it says "Please Perform extended diagnostics" and then it reports "Congratulations, your drive passed all tests!"
A little weird....
Looks like failing drive, but could this also be IDE controller communication failure?
I also tried replacing the 80pin IDE cable with a 40pin cable which is brand new. This makes no difference other than slower system speed.
Maxtor website has no info, MSI same story.
Now what??? ;(

JDeveloper IDE problems with google Calendar development libraries

Hello all,
I am using JDeveloper as an IDE for developing the google calendar events.
I am referring the http://code.google.com/apis/calendar/data/2.0/developers_guide_java.html site.
Instead of ANT to run the sample code, I am using JDeveloper IDE and added all required libraries from sample and source code.
Still I am getting weird error as Error(22,29): GDataRequest$RequestType not found in enum com.google.gdata.client.Service.GDataRequest.RequestType in class com.google.gdata.client.GoogleService in class com.google.gdata.client.calendar.CalendarService in class project1.CalendarTest
Code is as below
package project1;
import com.google.gdata.client.*;
import com.google.gdata.client.calendar.*;
import com.google.gdata.data.*;
import com.google.gdata.data.acl.*;
import com.google.gdata.data.calendar.*;
import com.google.gdata.data.extensions.*;
import com.google.gdata.util.*;
import java.net.*;
import java.io.*;
import sample.util.*;
public class CalendarTest {
public static void main(String[] args) throws AuthenticationException,
MalformedURLException,
IOException,
ServiceException
CalendarService myService = new CalendarService("exampleCo-exampleApp-1.0");
// myService.setUserCredentials("[email protected]", "pa$$word");
// URL feedUrl;
// CalendarFeed resultFeed = myService.getFeed(feedUrl, CalendarFeed.class);
// feedUrl = new URL("http://www.google.com/calendar/feeds/default/allcalendars/full");
// System.out.println("Your calendars:");
// System.out.println();
// for (int i = 0; i < resultFeed.getEntries().size(); i++) {
// CalendarEntry entry = resultFeed.getEntries().get(i);
// System.out.println("\t" + entry.getTitle().getPlainText());
Please if somebody has already faced such problem, show me some way or give the direction.

Problem is solved by changing jdeveloper Compilat settings.
Checked the checkbox of 'Use Javac'.
and then compile the project. It will get compiled.
Thanks to Shishir Shrivastava's post
http://www.mail-archive.com/[email protected]/msg00984.html
-Vedika

Please Help. NetBeans IDE Problem + rt.jar. Trouble compiling MIDlets.

Hi all. For the past few weeks I have undertaken learning Java for mobile devices. I am having a slight problem with NetBeans 5.5 which I would appreciate help in fixing.
Currently installed on my system:-
- Wireless Toolkit 2.5
- NetBeans IDE 5.5 + Mobility Pack
- j2sdk1.4.2_13
- jdk1.6.0
- jre1.6.0
- javaee sdk5_02
(So pretty much every Java application!)
Now the problem. Basically, if I import the following at the beginning for my MIDlet...
import java.io.*;
import java.text.*;
import java.util.*;
import javax.servlet.*;
import javax.servlet.http.*;
import java.sql.*;... the java.sql has red line underneath saying "package does not exist". Now, what I found is that I need to import .jar files into the Library section. I managed to fix the javax.servlet package and some others, by importing the correct .jar files, but I found that to remove the red line for java.sql I need rt.jar.
However, this is located under one of my jre folders and not the j2me / jdk folders I have. Even though it removes the red line, when I compile the project I keep receiving "PREVERIFY" errors and "CONSTANT POOL" errors.
Yet, if I remove the rt.jar file, these go away, but it won't compile then because it says the package is missing (back to square one!).
So, any ideas please??? I have spent days and days just adding random .jar files to try and fix the problem but to no avail. An example of current imported .jar files in NetBeans:-
- rt.jar
- midpapai.zip
- jdbc.jar
- servlet.jar
- runtime12.jar
- classes12.jar
- ojdbc.jar
Try not to be too technical, I've only just started out. Lol. Thanks in advance!!

well... J2ME world is quite diffirent from usual Java. Actually you will not be able to use much of the staff, that you have imported, including java.io.* (it will be only available in CDC), java.servlet.*, java.servlet.http.*, java.sql.*
So don't even try to find where are those packages are located....
Try from simple tutorial like:
http://developers.sun.com/techtopics/mobility/midp/articles/wtoolkit/
Or from documentation on Netbeans.org:
http://www.netbeans.org/kb/trails/mobility.html

JDeveloper IDE problems

I have a couple of persistent problems with the IDE:
i) I repeatedly get access violation errors and instances where the IDE just hangs, usually when I am just editing code.
ii) When I run an app from within the IDE the javaw.exe does not terminate when I terminate the app. A new javaw.exe gets added each time I run the app.
... and how do I control its hunger for memory ...
Bob

What OS and how much free memory do you have (before launching JDeveloper)?
It it best with at least 128 MB all to itself (more is better).
I typically run it on an NT machine with at least 256 MB of base RAM. This machine doesn't have a local RDBMS, if that were the case you would need to really double that (to 512 MB) for smooth operation. If you also have OAS running, add whatever it requires onto that as well. If you have a machine with all 3, you better have at least the 512 MB... I suppose tuning the SGA size on the RDBMS could allow for better numbers, but I don't no of any way to reduce the OAS or JDeveloper memory requirements...

IDE problems

There are a couple of problems with the IDE that were
acceptable in Beta releases, but should have been fixed for the
Release.
1. The compiler (builder) reports each problem 3 times. A
minor problem, but one would think easy to fix??
2. IDE crashes during builds. It is hard to tell what is
going on when the crash occurs but it may be related to thread
timing issues?? It seems to happen more often if I start a build
right after doing a save or save all. Also if I do a clean after
starting the IDE the odds appear to increase for a crash. I know
that's not much help. However it is frustrating because sometimes
after I get a crash I can't get a clean [non-crach] build until I
reboot, which is a pain.

Hi David. If you have been using any previous Beta release of
Flex or FlexBuilder, we strongly recommend that you discard any
Workspaces and Projects that were created with those previous
releases (of course don't throw away your source code!). After you
create a new workspace and project, see if the problems go away. If
not, could you give some more details on what you're seeing - what
is the exact text of the problem that's being reported 3 times,
what is the line of source code that causes the problem, any other
info that you think might help us understand the problem.
If you are still seeing crashes then could you give us the
exact text of the crash message.
Thanks,
Mark Shepherd
FlexBuilder Engineering

IDE Problem

I have write an application that use a master-detail class as superclass of my JInternalFrames
The m-d(master-detail) class is a JPanel with 2 to JPanels as fields
When i subclass the m-d i have notice that it's no way to drag and drop a JComponent from the ide's component palette because the code that the ide generate is:
getConentPane().add(...); -in NetBeans
this.add(...); -in JDeveloper
and i want the component to be added to de "detail" Panel.
the work around in NetBeans was to override the getContentPane() method in superclass to return the "detail" field.
but in JDeveloper i never find a way to resolve that.
i also found on http://www.jguru.com/faq/view.jsp?EID=3770
this problem is also in Visual Age and there exists a solution!
Are the all IDEs stupid ? So few people use superclasses with containers and it's no need for this feature?
Anyway in NetBeans the solution work only for 1 container.
After i generated the beanInfo for my superclass the IDE (both NetBeans and JDev) is capable to draw the ancestor components to my subclass. So why is a BYG problem to generete the a code like this.detail.add(...)?

It's not advanced it's ESSENTIAL and is not possible to write by hand because the NetBeans regenerate the code.....
or "by hand" means to write
setBounds(217,131,24,37)??????????
I use this in DOS programms !!!!!! Pascal for DOS , FoxPro for DOS!!!!!

Installing Mobile Plug-Ins in the IDE problem

Hello,
I try to install the IDE plugin Mobile in SAP NetWeaver Developer Studio by following the help of SAP. My problem is in the installation of the mobile application for laptops I can not find the folder \ Program Files \ SAP \ IDE \ CE \ eclipse \ plugins \ com.sap.tc.ap \ comp, and I can not find the default.confdef file
thank you for your help

Hi,
Please let us know whether you are using NWM 7.1 or 7.3
If you are using 7.3, then you cannot find these files. The procedure is different from that of 7.1, just you need to extract all the plugins into the eclipse plugin folder.
For 7.1, refer the following document
http://help.sap.com/saphelp_nwmobile71/helpdata/en/8f/0b674240449c60e10000000a1550b0/frameset.htm
For 7.3 refer the following document
http://help.sap.com/saphelp_nw73/helpdata/en/47/a834ce06cd2af3e10000000a42189b/frameset.htm
Hope this helps.
Thanks and Regards,
Suma

K7n2 ide problem

Similar Messages

Maybe you are looking for