K7N2 Wont work in user mode

Hi, i just installed my K7Ns with an XP 2000+ and a Radeon 9500pro and 512mb(2 sticks, only reading as 128 each) of Infinion PC-2100 DDR. Now, when I set jumper 10 to user mode, my machine crashes, but when it is in Safe mode, my system runs fine. Does anybody know what is going on?

well, i messed around with J10 and 11, and messed around with the FSB in the BIOS, and it finally came back to life.

Similar Messages

  • Wont run in user mode

    I can load and run adobe cs5.5 in windows 7 on our school domain, but when I log into the computer with a student account it says cannot run in guest account.
    Adobe says I need to grant full admin rights, but this is impossible and does not make sense, I work at a College, the whole point of a College network is to restrict student access, adobe must realize a large part of their clients are in this same boat. I have never had a problem with xp and previous versions of cs.
    Please help me?
    Ian

    Thanks,
    just to clarify,  think i need to grant the rights, re-install in admin mode, test in user mode, than go back to group policy rights?

  • Coldfusion dev installer wont work - "installer user interface mode not supported..."

    i just downloaded the os x version of coldfusion 7 mx
    developer edition (for the thrid time making sure the download
    wasn't corrupt) and extracted the zip and launched the installer by
    double-clicking it. the install screen pops up where it lets you
    choose what language and i press ok. almost instantly i get an
    error message to pop up that says... "Installer user interface mode
    not supported. Unable to load and to prepare the installer in GUI
    mode."
    umm... what?!
    does anyone have any idea what's going on and why the
    installer is misbehaving?! thanks!
    : : michael

    and the answer for others stuck on this...
    the problems is an installanywhere bug where if the anything
    in the directory path contains special characters like "!" or "#" ,
    it causes problems with the install. in my case, the directory path
    had a "!" in it... hope this helps someone else out!
    : : michael

  • X3500 wont work in Bridge mode with ASA 5505

    Hi Everyone, I am currently running Linksys X3500 v1.0.0 and plan to use ASA 5505 as a PPPoE client. While PPPoE connection is working fine when i configure the linksys for PPoE, but When I configure the ASA 5505 to act as PPPoE client I'm unable to get the Linksys get the Internet up and running. I have opened support ticket with Cisco and per them X3500 is unable to provide PPPoE details in bridge mode. Cisco Ticket # 62968611 (PPPoE connection not working) The error on Cisco console is - asa5505# PPPoE: send_padiSnd) Dest:ffff.ffff.ffff Src:c8b3.735d.4e13 Type:0x8863=PPPoE-Discovery PPPoE: Ver:1 Type:1 Code:09=PADI Sess:0 Len:12 PPPoE: Type:0101VCNAME-Service Name Len:0 PPPoE: Type:0103:HOSTUNIQ-Host Unique Tag Len:4 PPPoE: 00000002 PPPoE: padi timer expired Can Linksys help.. What's the issue. Regards, Sumit

    Hi! I'm not so familiar with the Cisco ASA 5505 device. If you set your X3500 to a Bridge Mode, it will not give any PPPoE mode details and vice versa. Which of the two devices would you like to connect to the ISP's connection, is it the X3500 or the ASA 5505?

  • Tata Photon is not working on user mode

    Hi Professionals,
    I've an issue with running Tata Photon + on user login, whenever I open the photon application its asking Administrator credentials to run the program. Is there any remedy to solve the issue and run the program without Admin credentials??
    Please help me..
    Thanks..

    Hi AriGM ,
    Are you logon with an administrator account ？
    If we logon as a standard account ,I am afraid we cannot run it without the administrator credentials .It is related to the UAC (User Account Control )It is necessary to distinguish the standard account with the administrator account to ensure the safety
    of the whole system .The administrator take full control of the system and the standard user is in a limited environment .
    Here is a link for reference:
    What is User Account Control?
    http://windows.microsoft.com/en-hk/windows/what-is-user-account-control#1TC=windows-7
    Best regards

  • Reason Arp wont work in Rewire Mode

    Hi All,
    the title of this thread pretty much explains my issue. i rewire appropriately, get sound and everything, but when i use reasons arp with a reason instrument.. it doesnt work. to test, i just opened reason and used the arp just in reason and it worked fine, so i know i am using it the right way.. any help on this??
    thanks everyone

    Did you try changing uefi to legacy?

  • Firefox Crashes and Hangs when opened and wont work in safe mode

    I use a mac OS X 10.6.7
    I have tried to follow your guides but I have been unable to stop firefox from crashing. I disabled all the apps via safe mode and the programme still crashes.
    I type in about:crashes but only had time to get the last crash details

    Thanks for the note about profile locations.
    I deleted mimeType.rdf in my existing profile, still have the same issue - can't view Tools -> Options for the Applications tab, or download a file. Same goes for a new profile - the same issues arise.
    Firefox never does crash, I can leave it in this hung state for hours (I left it in a 'not responding' state last night and it was still hung this morning).
    I was going to add a screen shot to this post but Firefox hung when I clicked on the 'Browse' button. Perhaps this is an issue when FF tries to interact with my directory structure? Does that get us any leads on what's wrong?
    FYI, I currently have my antivirus disabled & not running in the task bar just in case that was interfering somehow.

  • My passcode wont work on ipod touch the recovery mode wont work because of nno network connection, what do i do

    my pascode wont work, ive tried the recovery mode but that wont work because of a network connection error, what do i do

    Does the the computer connect to the internet?
    If yes
    Update Server
    Try:
    - Powering off and then back on your router.
    - iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server
    - Change the DNS to either Google's or Open DNS servers
    Public DNS — Google Developers
    OpenDNS IP Addresses
    - For one user uninstalling/reinstalling iTunes resolved the problem
    - Try on another computer/network
    - Wait if it is an Apple problem

  • Hey, my ipad is disabled and i cant open. i tried connecting it with itunes in recovery mode to restore it but it wont work it doesnt show and options itunes doesnt detect my ipad in recovery mode. what do i do know? please help!!!

    Hey, my ipad is disabled and i cant open. i tried connecting it with itunes in recovery mode to restore it but it wont work it doesnt show and options itunes doesnt detect my ipad in recovery mode. what do i do know? please help!!!

    If you followed these instructions and you were unable to enter recovery mode, I'm still leaning toward a hardware problem.  Also, since you have IOS-7, read this.  It might help.

  • I updated my iphone 5 to ios 6.something to get rid of a notification and it went into recovery mode!!! My photos are not backed up or on icloud. i havent restored yet bc i cannot lose my photos but tinyumbrella wont work. HELP! please:(

    I updated my iphone 5 to ios 6.something (something about the speakers) to get rid of a notification and it went into recovery mode!!! My photos are not backed up or on icloud. i havent restored yet because i cannot lose my photos/videos, etc. but tinyumbrella wont work to exit recovery mode. HELP! please:(
    i tried tinyumbrella (and another similar software) to exit recovery but it only remains on the apple logo stuck there. please is there anything else i can do? i've contacted apple and they have told me the only choice i have is to restore and lose all my data.
    my iphone isn't jailbroken and i've updated before without this problem so i'm not sure what has happened. is there anyyy hope please ???

    First I would try to hold down the power and the home button for about 15sec, but at least as long as the iPhone restarts, if it is still stuck or still in recovery mode then I can suggest you the tool "Wondershare Dr. Fone for iOS", it is both a Windows and Mac tool and I just used it today to get my iPad out of the Recovery mode.
    Tell me if any of these options worked for you.

  • After updating to itunes 10.4 restarted, my ipod touch went into restore mode. when trying to restore it says unexpected error occured (1604) followed resolution checklist . still wont work, any thoughts............

    After updating to itunes 10.4 restarted my pc windows 7 64 bit, my ipod touch 3rd gen went into restore mode,when trying to restore it works for several minutes then says it cannot be restored, unexpected error occured (1604) I have followed the reslution checklists, still wont work, any thoughts?

    Hi
    Cannot offer any thoughts other then i am having the same problem. updated my itunes windows7 32bit ipod touch 4th gen. went into restore mode lost over 700 songs. i dont get any error messages i just cannot get into itunes store. Firewall is allowing access, etc resolution checklists done, and nothing.
    Hopefully this issue is fixed up soon...

  • Keyboard doesn't respond at login window... works in Single User mode

    I have a G4 xServe (server 10.3) that won't accept keyboard input at login window, but the same keyboard, usb port, works fine when I'm booted into Single User Mode.
    Booting into Single User mode, something interesting gets posted during boot:
    "AppleCPUThermo got unsupported command"
    Any thoughts?

    Did you find a resolution to this issue? After I installed the latest security update to OSX Server 10.4.8 I am now experiencing the same problem. Any insight would be greatly appreciated.

  • Hi,i have the new ipad 16gb it was working fine till i went to download te new i tunes and the apple mobile device recovery mode my windows pc cant find the software to download it i need help because my ipad wont work i only see the itunes en usb symbol.

    i have the new ipad 16gb it was working fine till i went to download the new itunes and the apple mobile device recovery mode my windows pc cant find the software to download it i need help because my ipad wont work i only see the itunes and usb symbol can anybody help me.

    Try these instructions:
    http://support.apple.com/kb/TS3281
    You may also have to go to the link in the bottom paragraph if the first page instructions do not work.

  • I disconnected my Ipod classic from a receiver in "user" mode and now I can't get the Ipod to work via USB in my car or receiver. HELP!!

    I disconnected my Ipod classic from a receiver in "user" mode and now I can't get the Ipod to work via USB in my car or receiver. HELP!!

    See the following for how much you will have to pay for the exchange.
    Apple - Support - iPod - Repair pricing

  • Keyboard and mouse wont work unless booted in safe mode.

    So my keyboard and mouse wont work at all when i start up normally, so i coudnt even log on, then i tried safe mode and i was able to use the mouse and keyboard and log in, then when i loged in i got some messages:
    *+System extention cannot be used+*
    +The system extention "/system/library/extentions/IOUSBFamily.Kext" was installed improperly and cannot be used. Please try reinstalling it, or contact the products vendor for an update.+
    And 2 others: MicrosoftMouse.kext and msdosfs.kext
    Im pretty sure how i got this problem, i was using bootcamp and i got this program called MacDrive (bad Idea)and it corrupted my HD or something so i had to use disk warrior to fix it. I also used disk utility in safe mode but there were no errors it said.
    and this is probably a hardware problem but i cant use DVD's anymore, my drive will only read CD's now, must be broken....
    so ya, i dunno what to do exept get my drive fixed and to a backup and reinstall OS...

    Hi
    There are no many options which could solve this problem.
    It can be a hardware problem or software related issue.
    Can you use the internal keyboard within the BIOS?
    Check this.
    If this would not be possible, I assume the hardware is faulty.
    Additionally I recommend testing the keyboard and touchpad using the factory settings.
    Recover the notebook and check if the keyboard would functions. Otherwise you will need an helps from an notebook technician in order to replace the keyboard and touchpad

Maybe you are looking for