K7n2g-ilsr Problems Still Stay:)))

Dear MSI time!Try to install Motherboard MSI K7N2G-ILSR BIOS 1.8 END
TV TUNER MSI TV@NYWHERE MASTER ,OPERATION SYSTEM WIN XP SP1 CPU BARTON
2600+ MEM DDR333 512MB WITH LAST DRIVERS FROM MSI WEB PAGE:)))
WHEN PC TURNOFF BLUE SCREEN:)SOUND FROM TUNER WORK 5 MIN END GO OFF:)
IN BULGARIA TV SYSTEM IS NOT SEKAM:)))
wHEN DRIVER MSI8606 AUDIO CAPTURE DISABLE BLUE SCREEN NOT.
TRY USE DIGITAL CAMERA FROM MUSTEK GSMART LCD2 PROBLEM COPY PIC FROM CAM
ERA TO PC:)))CAMERA WORK PERFEKT WITH OTHER PC..S ,I TRY WITH 5 OTHER..
I TRY OTHER MTHERBOARD MSI K7N2G-ILSR PROBLEMS STILL STAY:)))
I WORK WITH PC..S 10 YEARS END SUCH unseen, compatible SYSTEM FROM MSI...
Congratulate s. o. on his success!!!!

Quote
Originally posted by BG-User
i have 8 pc...s:)))but this MSI System is "N1":))
I do not need help MSI needs help:)))
Hi BG-USER,
Since your not looking for help I guess you are posting on here to complain to MSI. None of the people in this Forum are MSI employees so they won't get your message. Complaints are made by contacting MSI directly. You can call them or e-mail them.
Cheers

Similar Messages

Help needed - K7N2G-ILSR problem

I just got a K7N2G-ILSR mobo and after I installed it, I get an error "NO DRIVE ATTACHED TO FASTTRACK CONTROLLER. NO BIOS INSTALLED"
I downloaded the latest bios and flashed it but I still get the same error.
When I am in the setup, it recognizes my harddrive (which is a Maxtor IDE).
I'm not using serial ATA.
Please help me figure this out.

the problem is that after i get that error message, it takes me to the windows safe mode menu. after i pick a windows mode to start up with, it re-boots only to bring me back to the original error message.
i can't boot into windows.
here are my specs if this helps any...
K7N2G-ILSR
Athlon XP 2600
Corsair XMS pc2700 512mb ram
Maxtor hard drive (8gb)

K7N2G - ILSR problems ...

Right, this is a long story!
I got my K7N2G a few months ago now, started by using PC2100 (Generic, lol) ... it worked quite well - I can't remember getting crashes!
I then upgraded to 2x256Mb PC3200 TwinMOS, not knowing about this whole picky RAM thing - I'd heard it was good RAM so I got me some ... after replacing one because of a bad stick I had both sticks running well, I then started getting lotsa freezing in games (esp. UT2003) and I thought it was just overheating but after doing some overall quietening (Zalman GPU, new CPU cooler), it was still crashing ... then the fan on my chipset died so I stuck a new 40mm fan ontop and seemed allright but was still getting the odd freeze in-game! Eventually was told that the 40mm fan wasn't actually needed so I removed it and things didn't get any worse ...
Untill now, I get crashing in game very often and I have lost my USB ports)!
Is any of this todo with my RAM, or chipset fan removal?
Also this is an engineering release ... is it safe to update it with the latest K7N2G-ILSR BIOS?
I had less problems with my ECS K7S5A, lol!
Thanks for reading and hope you can help ... Alex

Quote
Originally posted by UnrealRocks
Well, thats put a stop to that system ...
Switched it on this morning and BOOM - one hell of a bang and flash ... PSU dead and rest of the system taken with it!
Grrrrr!
Sorry to hear that your dead in the water. :( Since your going to buy a new PSU "DO NOT BUY A QTEC" Stick with an Antec or Enermax 400W+, you may pay a little extra but this is one of the most important components of you system so it's worth it. It will help eliminate a lot of problems in the future.
Rob

MSI K7N2G-ILSR Problem! Need help!

Hi,i bought a K7N2G-ILSR last year when i was in Germany. This mainboard never worked as well... I wanted to work with Athlon XP 2500+ and Dual Channel 256MB+256MB=512MB 400 Mhz DDR-Ram. It hasn't worked when i first wanted to use and i changed the jumper to the securit mode than it worked but it has never opened with one button pushing.I was always trying to get screen vision with 3-5 closing and opening.One day i tried to get the jumper back and i tried to open but it never worked. I got the jumper securit again but again never worked. I tried everything but it never worked after that event. Normally i had to inform it at first and give it back or give it to the repairing but i couldn't have time. Now i have to do it this time. Now i want to change this or something else but in Turkey. I am living in Turkey and does MSI Support Centre change it or repair it? What can i do to get rid of this problem. Need help!
Thanks for your helps from now!

MSI K7N2G-ILSR Mainboard 11X166
AMD Athlon XP 2500+
2X256 MB PC 3200 Twinmos
OnBoard Graphic Card
Samsung 40 GB 5400rpm HDD
300 Watt Power Supply
I dont have more infos but i can find out if you want...

Host of k7n2g-ilsr problems

Well I think I got a bad mb....I just got it the other day and finally found time to install the thing. In retrospect I probably should not have even installed it....in any case my problems started.
First.....when I turn on the power....the system comes up with the splash sceeen (8xtreme) and sits there for about 4-5 minutes even after hitting the delete key I have to way prior to going into the bios settings. When I finally get into the BIOS settings I configure the system to quick boot and turn off the splash screen. I also go to the settings to detect my hd and cdroms. I press enter on each resource and it take 3-4 minutes to return after pressing enter to have the machine detect the drives i then change the option from auto to manual.
I save the settings and reboot the machine.
During the reboot it still takes 4-5 minutes to "Detecting IDE drives ..." and getting to the screen that shows the system configuration and thus continuing to boot. Now the next problem comes it....it takes another 5 minutes to get to the point where the floppy or cd rom actually boots.
I am able to get a floppy to boot and get me to a dos prompt....I then made a boot cdrom and put the new 1.2 firmware on it to flash the system. I flashed the new firmware with no problems hoping this would fix my above issues.....didin't work....the problems still exist.
I then inserted the XP installation cd to try and install that....the only screen I got to is where the machine says it is tyring to detect my hardware and then it goes black....I left it sit for another 20 minutes and then nothing.
I tried my redhat 7.2 install and it seemed to install fine...but the problem is the machine is unable to boot from the hard drive because I keep getting install a valid boot device.
I have no idea what the heck is going on with this mb...I think it is safe to assume it is bad and now I will have to send it back and wait another month for MSI to send me another one.....anyone have any other ideas as for what I may try....btw....the bracket with the lights shows that everything is OK....all green so thats about it for now...tired of playing with it. HELP!

One ide1 which is the middle IDE connector on the mb I have 1 western digital 80 gb hd....it is jumpered to be the master drive
On ide2 which is the top ide controller I have two dvd writers one hp and one pioneer the hp is jumpered to be the master and the pioneer is jumpered to be the slave.
I have tried to cut down all of the hardware that is internal to try and limit the positibilities to where the problem may be coming from but I keep going back to it being a bad mb.
This is now the second bad mb that I have gotten from MSI....maybe they are having quality problems coming out of production...it's the only thing I can think of.

TS2446 My Apple ID is disabled on the Iphone for apps. I've reset the password but the problem still stays.

My apple id is staying disabled even though I've reset the password.

From the article you linked:
If the issue persists, you can visit iCloud Support, iTunes Support, Apple Print Products, or contact AppleCare for further assistance."

K7N2G ILSR - Problems with Geil PC2700 memory

I am having issues with my k7n2g and its ability to init GEIL memory. I can not get the system to init the memory consistently, have the time it will just hang. Since the company Xtreme Gear will only swap for additional geil memory, I would like tomake this work. Any ideas on the exact settings for the memory? I have tried adjusting the voltage to 2.7 as suggested on the geil memory package but that does not help.

try setting memory to High Performance in bios

USB 2.0 problem (K7N2G-ILSR and HP PSC 2210)

I'm using a K7N2G-ILSR mainboard in combination with a HP PSC 2210 all-in-one printer. The printer sometimes stops printing and produces an error. The print can not be deleted and I have to reset the computer.
I'm using the latest HP drivers for the printer, Windows XP Pro with all Windows Update fixes and the latest upgrades for teh mainboard (Live-Update).
Is this a known error and is there a fix/workaround (can I set the USB in the BIOS to 1.1 only (instead of 1.1 and 2.0)??
According to HP it is related to the chipset and the USB driver. Until now I have not find a document explaining the problem for this mainboard and a proper solution.
Does anyone have an idea?
Thanks for your help!
Cees

Cables are cables still at this point in the game so it could be that you have a faulty cable but there are no special 2.0 cables to buy...
Never been a big fan of the All-in-one printer/scanner/copiers, I've had nothing but problems most of the time when my clients buy them...but they still buy them...if you think about it they really only came out just over a year and a half ago so that technology isn't quite mature yet...
I doubt that it has anything to do with your setup directly, it sounds like a driver issue and one that's clashing with another driver that's used for something else in your machine...no I don't know what cause I don't know what you are using in your system heheheh
I had a client that bought one of the newer photo printers, why I don't know cause he doesn't even own a digital camera, but he just had to have one, but anyway, it would error out everytime he tried to print to it...I reloaded his system and systematically added in one component at a time...writing down everything I did...when I put in his ATI All-In-Wonder card and loaded the software for the TV part lo and behold when I printed I got the error again...couldn't fix it for my life either with all the newest drivers from ATI and HP...went backwards in time for older drivers to no avail...the guy stiffed me on the bill for over $1000.00 and I've not heard from him again so I can't tell you if he fixed it or not at this point...
Cheers!! 8)

Raid problems with K7N2G ILSR

I have the following setup and problem:
K7N2G ILSR
NEC DVD-+RW 1300A
Seagate SATA 120gb HD
350W PSU with "210" 3.3 + 5.0
BIOS V 1.4
2 x Hynix 256mb DDR 333
I was able to setup the SATA drive as a single RAID drive and install XP pro.
Now, 9/10 times, the system will not boot. I receive a
"No drive attached to fasttrak controller"
message.
When the system DOES boot, it works great, and I can leave in on for days with NO problems.
I know the Hynix memory is not "approved", but since the system is stable (when it does boot), and assume its not a memory problem.
The problem still occurs even after:
I changes the SATA cable (data and power)
I changed the DVD cable and slot (1-3)
I even disconneced the DVD and / or Floppy.
No change
Help!!!!!

I have already tried two different types of Ram. 512 MB DDR 333 (I don't know the timing exactly but it's a CL2.5 Ram) and another one from a different manufacturer. Also DDR 333 CL 2.5. Then I combined both. But the raid controller didn't show any reaction and I can't imagine that the problem is the power supply because everything else works fine. Anyway... I will try to get a new K7NG2-ILSR on guarantee, sell my whole computer and buy the new K7N2-Delta because I have only problems with the K7N2G-ILSR.

[nForce] K7N2G-ILSR network connection problems

My brother's system is as follows:
AthlonXP 2000+
MSI K7N2G-ILSR
2x256 MB Crucial PC2100
Emermax Powersupply
Generic DVD ROM
LG DVD burner
MSI TV @nywhere
WinXP Home SP2
His computer has been working more or less perfectly, although the TV card occasionally causes some trouble. Today, he was no longer able to get on the internet. From both the Network connections and Device Manager screens, his LAN interface is gone. Only the 1394 interface shows up.
So far, I did a system restore to last week, which had no effect. I made sure the BIOS hadn't disabled it for some reason, too, but that isn't the problem. I manually installed the network adapter, and it said that the device could not start, error code 10. The network adapter will not work in Safe Mode with Networking, either. I tried the MS Knowledge base article regarding missing LAN icons, but that article was for situations in which the icons were gone yet everything still functioned, so it didn't really apply. Reinstalling drivers had no effect. I can ping localhost, but that could just be because the 1394 connection can act as an internet connection.
Any ideas? I've not done a repair of Windows on the machine, but I'm not sure that would help. I do have an extra network interface pci card I could put in if it is simply a problem of his onboard connection having died. If I do this, is there a particular PCI slot that I should preferably use to avoid IRQ conflicts?

As far as I know drivers can be installed in SafeMode, but your LAN wont work till in normal.
A repair install is not a bad idea, as Windows is very fond of its own drivers.
LAN and sound problems are often early signs of a PSU near the end. You wouldn't know the specs of the Enermax? I guess it is alright, but you never know.
As the TV-card is problematic, try that one in another slot. Nowadays devices happily share IRQs without problems, but some older devices including older mobos (which is not the case here) were very conservative. ...I'll have to look in my drawer, wait a sec, please. - - --
"The use and sharing of IRQs aren't mentioned in my MSI manual, (due to the APIC function I think), so I had to go to some ASUS manuals. As standards are standards, I believe things can't be to different. If someone has any addings or suggestions please come forward, so I can adjust the table.
*Please note that this is generally speaking and mainly for ASUS boards a few years old!
**Please note that you should not have any sharing with the IDE controller or similar!
***Please note that it is a good thing to have expansion PCI sound cards in slot 3!
****Please note that surprisingly enough it looks like PCI slot 2 would be free for any device, but AGP cards get hot and bigger so it is not a great idea.
IRQ sharing table
PCI 1 shares with PCI slot 5
2 shares with AGP and PCI slot 6, or sometimes with onboard IDE
3 shares not, or sometimes with onboard audio/modem
4 shares with onboard LAN
5 shares PCI slot 1
6 shares with AGP and PCI slot 5
AGP slot shares with PCI slots 5 and 6
USB 1 shares with USB 2, 3 and USB 2.0
2 shares with USB 1, 3 and USB 2.0
3 shares with USB 1, 2 and USB 2.0
USB 2.0 shares with USB 1, 2, and 3
Onboard audio/modemshares not, or sometimes with slot 3
Onboard LAN shares with PCI slot 4
Onboard IDE shares not, or sometimes with PCI slot 2 "

K7N2G ILSR + 40 GO WD CAVIAR problem

hello,
sorry for my english...
my configuration :
MSI K7N2G ILSR (all bios and driver upgrade with live bios)
Athlon xp 2600 + barton fsb 333
512 ddr
20 go western digital 7200 tr
40 go ibm
burner traxdata 16/10/40
win xp pro sp1
my problem :
when i put another hard drive (western digital caviar 40 go 7200 tr) on this mother board my winxp won't boot !
it stay fix with the AGP 8X logo (green color) in the dos.
i try to put in ide 2 master or CS or slave with other drive. i try in ide 1 on slave or CS. i try on raid ide
and it's the same think! this hard drive is ok on all other computer.
do you know this problem? do you have a solution?
tanx
léo

FIXED the problem but its not something i would recommend for someone who isn't very carefull about this. The problem is a "timming issue" to fix the problem Cut 2 of the 42 pin wires be VERY CAREFULL PLEASE!!!!! u cut the red one and the one wire next to it.. Make sure you DON'T short it. Plug the sucker back in and Walla it works.. now for thows who dont want to do this and have all the time in the world WD customer support will send you the wire if call them up that has the 2 leads already Cut.
- Dan
Hope this helps and please if you don't feel up to it don't do it! trust me is scary just thinking i could burn up my mobo ...

K7N2G-ILSR raid boot problem

Hi,
I have an msi K7N2G-ILSR mobo and am having boot problems on the raid system.
Everything worked fine (raid 0 set up sata) and would boot fine, the bios had to be set up to look for other boot devices in order for the system to boot with raid drives.
Problem occurred when I added an ide card to give me 2 more ide channels. Still fine if I only connect cd roms to new card but as soon as I connect a hard drive it appears the msi board stops looking for the raid drives as a boot device, because I get the message NIVIDIA Boot Agen PXE-2.0(build 082 v1.82)
Copyright......................(info)
Copyright......................(info)
CLIENT MAC ADDR 00 10 DC E1 4C AD GUID:
FFFFFFFFFF..-FFF..-FFFFFF... etc.
PXE-53: No boot filename received.
PXE-MOF: Exiting NVIDIA Boot Agent
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER
It seams there needs to be a bios update as when you scroll through boot options (first, second & third) in advanced setup there is no choice for raid. Therefore the only way to boot from raid is to choose “look for other boot devices” and that is OK until you add a second ide card with hard drive on.
I have version 1.6 bios (latest on msi`s site)
Any idears on how to get round this ?

Hi Raven,
For your info windows xp will support any number of ide channels (upto the number of spare pci slots you have).
I have another computer that has 2 extra ide cards in and has 2 dvd`s (on seprate channels) & 6 hard drives as well as raid hard drive set up. Windows is not confused and supports all devices and has done for the last few months ! This mobo has boot from raid in its bios so has no problems on boot up. The reason I need so many ide channels is simply I do video work and need loads of storage space so until I can buy 800gb hard drives for a reasnable price I am stuck with having to buy 200gb drives.
As I said it looks like either a bios update from msi or I`m going to have to buy a new mobo.
Regards.

K7N2G-ILSR MS-6570 Restart Problems!

K7N2G-ILSR MS-6570 Restart Problems!
Has anybody else had a problem like this . . .
Ive got this problem with two machines now!!!!
Say for example you boot your machine and go into the bios to change whatever. Then save and exit. It should reboot and carry on to go into windows (or whatever). BUT . . . both of my machines restart and then just sit there and give a long beep which then repeats.
If I turn the machine off completely then back on it starts up ok with any changes to the bios kept from last time.
Can anybody help?!?!??! ;(
I have updated to the latest bios (which is 7.2)

I now have the MSI K7N2 Delta-ILSR (601-6570-030).;
On the box:- NVIDIA nForce 2 Ultra 400 Chipset Based.
K7,nFORCE2 Ultra400/SPP,MCP2-T,FSB400,D-Bracket2,Round cable,2*SATA&power cables,1394 cable,S-Bracket,WinDVD4.
I have 2x256 PC3200 Corsair DDR and a XP2800 Barton, tried and tested at 240fsb(237fsb Totally stable), And I get the same thing happening to me..Also this board and the last one will NOT do the claimed 400fsb..
And dont say it's the ram because it's not, the ram and CPU are fine.... It's the Motherboard that is incompatable with the Ram & CPU
why because my Ram is Corsair(the name speaks for itself) and works in every system to date!.. The CPU is AMD also works in every system to date!
Soon as i get around 193+(fsb) it starts to do the same thing wont reboot, and does the beep thing! at 200x7 200x7.5 200x8 200x8.5 200x9 200x9.5 200x10 200x10.5 200x11 200x11.5= NOTHING NOTHING NOTHING NOTHING NOTHING NOTHING NOTHING NOTHING but BEEP ......BEEP.......BEEP.
I also bought a brand new Antec TRUEPower550Watt with front voltage control (£100+) and that still does,nt do it
this is my second board, and im totaly fed up with there crap board. I spent good money for this TOP Class Ram and dont expect to be told the Rams wrong when it works in every other system i have had my hands on!!!!!!!
MY advice is send it back and get an other and if thats no use send it back again and get a refund and buy an ABIT NF7-S.. with exactly the same components i get a fsb of anything(100) upto 240fsb abit..
SIG is old board

K7n2G-ILSR, Mouse problems

I have been having a lot of issues with my mouse since I got my K7N2G-ILSR MOBO. If I use the PS/2 connection; if I have to reboot after installing a program or something the mouse no longer works and I have to reboot again and it works fine. That is the task everytime I have to reboot.
I thought maybe there was a grounding problem with my mose connector or my PS/2 connection on my MOBO, so I went out and purchased a IBM optical mouse. Problems still persist although they are different ones now. The IBM mouse is USB, if I connect it to any of the USB connections its almost like it doesn't have enough power to run my mouse. The mouse's scroll button lights up blue and when I plug it into any of the USB ports I can see it flash a couple of times, but the light is very dim and then it just goes out and my mouse doesn't work at all. Tried doing the restart process and nothing happens at all. I tried all 4 USB inputs on the MOBO itself and even installed the USB 2 S-Bracket that came with it and the same problem happens in each one.
I just wonder if I should try another mouse like an intellimouse or are my connections on my MOBO just bad or something.
Any help would be very appreciated.
Thank you all,
Demonoids777
Setup:
MOBO- MSI K7N2g-ILSR
HDD- Maxtor 80GB 7200RPM 8MB Cache
2x 256MB PC2100 Kingston Memory
300 Watt PSU
Lite-on CDRW
Lite-on DVD
AthlonXP 2000@ default 1.667MHZ
Antec Aero-Flow Heatsink and Fan

Quote
Originally posted by Demonoids777
The Output is
+3.3V= 28A
+5V= 30A
+12V= 15A
The only problem with this theory is that it did the same thing in my friends case that has an Antec True Power 550 Watt Psu.
Any more help would be appreciated, Thank you.
Demonoids777
The problem is with the board, I've had 2 of these boards, and both of them had a problem with the mouse.
If you get a keyboard and mouse make sure they are both USB, or BOTH PS/2. If you choose the PS/2 option then make sure the keyboard, and mouse don't have any extra features.
It's odd, some keyboards and mice work fine, while others mess the whole computer up.
MSI NEEDS TO FIX THIS!!!
BioHaz

K7N2G-ILSR overclocking problems

I am experiencing some strange problems. First my system:
K7N2G-ILSR using onboard video
Athlon XP 1700+ Thoroughbred A, factory unlocked
2x512MB Corsair XMS PC2700CL2 memory
Debian Linux, 2.4.21-pre4-ac6 kernel
350W Enermax PSU
173MHz FSB, 10x multiplyer, 1733MHz CPU 1:1 FSB/CPU
1.65V CPU Voltage
1.2 BIOS
This system works rock stable, no crashes, no problems when it is running. But if I turn the power off, it no longer posts, if I remember correctly, the bottom two leds are on. It does not beep, no video nothing.
There is a procedure I can always use to bring the system back up, but it is a bit tedious:
1. Set the safe mode jumber
2. power on, the machine starts non-stop high/low beeps, no video
3. Press reset: the board boots up, go to BIOS setup, set the FSB to 133MHz and save
4. power off, reset the safe mode jumper
5. Power on, again the machine starts with high/low beeps
6. Reset: the machine comes up, enter the BIOS, set FSB back to 173MHz
7. Reboot, enjoy!
It always works, but it is a hassle. Not too bad, since the machine is on 24/7 so I only have to do this is there is a power outage of when I change some hardware, but it is very inconvinient.
The other strange thing is that I cannot set the DDR voltage to 2.7V. I can select it in the BIOS, save it, but after reboot it is back to 2.6V

Quote
Originally posted by wonkanoby
drives pull 2x or 3x current to spin up as do once spinning,thats what makes me think psu if a reset works but cold boot fails,disable all bar c and try a cold boot
I have tried that, removed my HD and my TV Tuner card, but it did not help. But I have discovered something new: if I turn off the machine only using the ATX power switch and do not turn off the PSU switch, the board comes back on fine. I also have a simplified procedure to revive the board after a power off:
1. Set the safe mode jumper
2. Power on, wait for high/low beeps
3. Reset and wait for POST
4. Turn off using the ATX Power switch
5. Reset the safe mode jumper while the main PSU power is still on
6. Turn on and boot
Note that I did not have to tweak the BIOS as before.
Also did anyone else had trouble setting the DDR voltage to 2.7V? I can set it in the BIOS, but it is back to 2.6V after reboot.

K7n2g-ilsr Problems Still Stay:)))

Similar Messages

Maybe you are looking for