K7T Pro and GeForce2 Ultra

I Probably haven't searched enough but I would like to know what you think. I purchased a GeForce2 Ultra 64mg for cheap. With the age of my board I would think it would work. The fan fires up but I have no output from the card. Is it a voltage issue? I remember something about this.
800mhz T-Bird
K7T Pro ver1:0
128mg Ram
TNT Riva 16mg
100mg (2 drives)
250 watt sparkle psu

Voltages are right on. I changed first display to agp but my little tnt card is agp and all works fine. Drivers aren't the issue as when I fire it up my monitor stays in standby. The other thing that happens is I get 4 red leds on my board. I thought that was cpu related. I get no trouble beeps. I'm going to take it to a local shop to test today. I'll post results. Thanks
800mhz T-Bird
K7T Pro ver1:0
128mg Ram
TNT Riva 16mg
100gig (2 drives)
250 watt sparkle psu

Similar Messages

Msi k7t pro and hdd crash

Hi.
I have a problem and i hope some of you can help me.
I have msi k7t pro and maxtor diamond max plus 8. disk crashed before few days after using it 3 months. Before that i had maxtor 540 series and he crached after 18 months of use.
Two disk had spin up and seek time problems. Whell at least siguardian "sad that".
Could this hdd crash be from nonquality disks or the could be caused from some other part of pc.
And now i have option to chance maxtor with seagate.
What do you thing about seagate disks.
thanks

a poor psu is all i can think

ATI Radeon 9800 Pro and kt4 ultra

Hello
i was curious to know of any problems with the Kt4 ultra motherboard and the Radeon 9800 pro??
my system constantly crashes back to the desktop, or completely locks when i play Command & Conquer Renegade.
there are also some "misdrawn?" walls in the game also,...
i have all the latest drivers for the motherboard and the card,(including the released today catalyst drivers from ati.com)
i have also tried the drivers from driverheaven.net, but same thing happens,...
this is truly aggreviating...
some system specs:
kt4 ultra
antec 380 true ps
2500+ barton running at 11.5*173 @ 30c idle, 33c full load
corsair 2*256 3200LL
built by ati radeon 9800 pro 128mb
ive read where you can increase the agp voltage to try and fix the problem...and i also saw where one guy was just going to buy another motherboard b/c of the issues...
any help is truly appreciated
thx

FWIW, in case anybody is reading this thread in future and has problems with this Board and this card, I can report that I have now(at my second attempt) successfully installed a Radeon 9800 Pro on MY kt4 uLTRA motherboard.
As noted above, I purchased a new Antec True Power unit, prior to installing for a 2nd time. I am not sure whether that was necessary, but it certainly didn't hurt. The successful installation process was as follows:
1) Download the latest catalyst drivers from ATI
2) Set monitor to lowest possible standard (640 x 480, 16 colours if possible - in my case my digital monitor could not be set lower than 800 x 600)
3) Uninstall drivers for existing video card
4) Replace video card
5) Install ATI drivers
6) restore settings on monitor to maximum.
At that point, after restarting the computer, I had a CLI.exe error. After Googling for this problem, I discovered that I needed to download Net 1.1 from Microsoft. After downloading and installing that additional program, Radeon 9800 Pro is now working perfectly.

MS-6330 (K7T Pro) and GF4MX

I'm thinking of buying a GF4MX and I wont to know if there are any known problems between this mother board and the GF4MX.

Hi,
I don't know of any problems unique to this particular combination, however I know from my own experience that the GF4 MX440 cards are rather problematic in most (maybe all?) systems. :(
If I were you, I would rather go for a GF4 Ti4200, which is somewhat but not that much more expensive, and a lot faster , or for a GF2 MX400 which while rather cheap still have descent gaming performance.
Best regards

K7T won't take Win XP Pro w/ GeForce2?

?( I got The K7T Turbo, and Geforce2 MX/400 Vid card, trying to install Win XP pro and when it checks the compatibility of my sys it says that it will not install because it found a conflict between my motherboard and my video card, but it doesn't say what the conflict is. I checked for ghost drivers and found one for the old vid card (Voodoo 5500) and got rid of it but still same problem, already tried reinstalling drivers...four times, still no fix, is there something between the K7T and G2 that i don't know about or what, I'm at a complete loss here, ;( any help will be richly rewarded with tons of cash that I don't have and won't be able to give you.

:: smacks self in head repeatedly ::why didn't i think of that?, I have no idea if there's anything there right now, i gotta go home and check, the memories of putting that thing together are beer fuzzy, someone else once suggested installing a generic vid driver for now till i get XP in...would that be a "healthy choice"..?...please note that the previous comment of "Healthy Choice" holds no relation to "Healthy Choice " food products which are Nutritious without sacrificing taste resulting in a delicious meal for the whole family.......ummm....too much red bule and starbucks...gosh I hope I don't get sue'd today 8o

K7T Pro (MS-6330)

I have a k7t pro and I want to get an athlon xp 1500+ in it. I know its not going to use the full potential of the processor but it is cheaper than an amd athlon 1.2 tbird.
I was running an amd x 1800+ on it before because i got it in a pulled system for free. it worked fine but will a 1500+ work stabily?

Dear Assaf !
'Since the K7T Pro only supports 200MHz FSB an AXP 1500+ (1333MHz) will only run at 1000MHz.'
This is true if you don't modify the processor.
On the other hand if you unlock the processor (paint the L1-bridges), paint/cut the L10 bridges and change the multiplier, then you can run the CPU at it's full speed.
I am currently running a XP1800+ (1533MHz) on a K7T Pro2 board with 102MHz FSB and a mult. of 16 (8 in BIOS +8 by CPU) at 1.63 GHz.
Regards,
/ErnyH

K7t turbo2 + geforce2 ultra

when i have my geforce2 ultra card in the k7t turbo2 motherboard i get weird charactors displayed. like on the bios screen, charactors will be grayed out or missing.
i also noticed this problem before with a different geforce2 ultra and a k7t pro2. is there a fix out or a way to fix this problem?
also, windows 2000 advanced server hangs on startup when i install drivers for the video card
MSI K7T Turbo2 v3.6
1.67Ghz Athlon XP 2000+
GeForce2 Ultra / Hercules 3D Prophet II
80GB IBM Deskstar / ATA100/7200RPM
512MB Micron PC133
Antec 300Watt PSU
SMC 10/100 NIC
RealTek 10/100 NIC
48x12x48 Burner
Windows 2000 Advanced Server
also i do have 2 NICS installed in pci slot 1 and 2. could this be the problem conflicting with slot1/agp?

my geforce4 ti 4600 works fine in the computer, as does my geforce3 ti 200.
this geforce2 ultra works fine in my other computer.
i took all nics out, there were no pci cards installed, and still get weird charactors on random spots of the screen
after leaving the computer unplugged with cmos cleared for a couple hours, now during 2k adv server setup i no longer have the acpi error. I can get the machine to install 2k advanced server now and windows runs perfectly until i install the drivers, windows will not make it to login after installing drivers and rebooting. ive tried many different versions of drivers

GF4 Ti4200 and K7T Pro ?

Hi,
I wanna buy MSI GF4200 64MB -8870- card.Just need info if this card is fully compatible with MSI K7T Pro (rev 1.1) matherboard(old bios)?Can I expect troubles with instalation?Since there is old KT133 (CPU Duron 1200MHz) chipset on matherboard,but I hope all will be ok,but for sure I'm asking here.Anyway is this card good?Thanks from info.
PS:I saw in our Czech diskussion pages there is pretty noise fan,but othervise is it very good graphic.

You have 2 capture sources, you need the software to be able to allow you to select the one you want.
You should try virtualdub, supposed to be good and it's free.

K7t Pro 2a problem (it boots and after 1 hour it stops)

Hey,
Since 1 week now I have a problem with my MSI K7T Pro 2a mainboard.
When I'm working the first hour(s) my pc works ok, but at a certain moment I hear a 'whistle' (somebody told me it's a condenser that works bad). When that sound is over (in less then a minute) my pc stops working.
The only way to shutdown my pc is to press the powerbutton for a couple of seconds.
When I press the powerbutton again it wont boot anymore. I could wait some time or I can unplug my pc and it works again for only 1 minute. After a couple of hours I can work further.
I check everything (powersupply, cpu, memory, hd) but I know for 100% that it is the mainboard.
I bought this on the 01/feb/2001.
Please help me.
Greets!
Rope (sorry for my bad english)

Hi, what have you done finally?Quote
Originally posted by foosman
Rope,
My motherboard is out of warranty...just barely. So, I decided to take a try at fixing it today. I noticed a capacitor that visually looked bad (it looked kind of rusty on top and was bowed out). I pulled it and a 2nd capacitor which was also connected in parallel with it. They were 2700uf capacitors...according to my meter, one measured 8000uf and the other 4100uf. I assumed these were bad and replaced them. I did not have any 2700uf, so instead used some larger 4400uf I had. I assumed these are bulk capacitors for power regulation and the size wasn't too critical. I still have the same problem. This did not fix it. Machine is behaving the same way. I'm getting close to giving up.
Can you tell me what you mean by condenser?
Regards,
Foosman
:]

K7T Pro V1 sound problems and CPU support

I have a K7T Pro V1 motherboard.
I can´t use onboard sound, because when I try to locate it (Windows 2000) on Add New Device, appears blue screen and text "Hardware malfunction. Call your hardware vendor for support. The System has halted".
What I can do? ?( ?(
I also would like to know why this motherboard does not support Duron Morgan processors only Duron Spitfire -versions? :( :(
Thanks for your help!

I have enabled all in BIOS:
OnChipSound Enabled
OnBoardLegacy Audio Enabled
Soundblaster Enabled
The system does not found new device automatically and when if I try to find new device manually, appears that error message and I have to boot the computer again.
I just wonder is the problem onboard?
About CPU´s....
Rob454 told "...theyre not officially supporting the Duron Morgan Cpus".
Does this mean I can´t use Morgans att all (even 900 or 950)?
I mean does these 900 or 950 Morgans also need SSE support?
And if I´ll try to use for example Morgan 1.2 Ghz does it work att all (or read as Athlon Thunderbird)?

Req: K7T Pro MS-6330 and CPU

Pls, I have MSI K7T Pro motherboard. In support page there is written that this MB supports Duron up to 1.1 GHz and Thunderbird Athlon up to 1.2 GHz (100 FSB) with a little older BIOS 314 . Is the info true and recent or are there any news on it and it supports at least Duron 1.2 GHz or higher CPU ?

I have the MS-6330 v5.0 board Running an XP1900+ CPU (1.56GHz). The more recent BIOS images allow for higher CPU speeds, but it is important to check the version # of you board to verify the version of the BIOS falsh it can handle. With the v5.0 boards you can use BIOS v3.6 which allows 2200+ CPU's

K7t pro ver1 boot up problem

Yesterday my system suddenly went out when I was installing Oracle under Mandrake Linux. And then it won't boot up, it don't post anything. I heard a long beep and followed by two short beeps during the bootup, the DLED was RED-RED-RED-GREEN (from top to bottom) at that time. And the DLED finally stayed at GREEN-RED-GREEN-GREEN.
I unplugged everything out except for the memory and cpu and cleared CMOS, then reboot, still same problem.
Anyone could give me a hint? Did the MB die?
MS6330 pro
Duron 1.2G
RAM 256+128+128
Western Digital 60G
Geforce2 GTS
Liteon 16xDVD
32xCDRW
winmodem
10/100 NIC
250 usb zip drive

K7T pro disease, dies with overheated power control chip. If uder 2 years old try RMA back to MSI for a replacement. For more info on the "disease" do a search on this forum using K7T Pro as the search data.

A brand new W540 and the Ultra Dock humms, black out external screen, won't recognize mouse and some

Just received a W540 and an Ultra Dock. Here is my first impressions.
During setup ... tried to connect my speakers directly onto the laptop.... HUMMMMM! (really loud humming sound, until Windows loads ...sounds like a short somewhere ...). Ok, obviously sound is not the main focus of W540.
After a little while... boink! ... and the external screen goes black accompanied with the "Windows detected something disconnect"-sound. No matter what I clicked on the keyboard, or how much a moved the mouse, the external screen wouldn't turn on again. I had to flip up the screen on the laptop, and tada, Windows reported that something connected again, and the external screen turned on again. Turns out that I need to keep the laptop screen open at all times now, and now and then both screens disconnect and connect again. Not completely a showstopper, but somewhat annoying. Ok, how to fix - enter "lenovo ultra dock black screen" in Google and see that a bunch of people have experienced the same thing. After some reading, I found this official support page "LENOVO THINKPAD PRO DOCK AND THINKPAD ULTRA DOCK ARE CAUSING DISPLAY ISSUES ON EXTERNAL MONITORS" (http://support.lenovo.com/us/en/documents/ht081248). Seems to fit my situation perfectly. Just download the fwdphb03.exe program and follow the instructions. But does fwdphb03.exe even start?!? NO!
Just a brief flicker and no application nor instructions to follow. In addition, I am Administrator on my machine. Please make applications that at least attempt to work....
I have an Aten mouse and keyboard switch (KVM) (CS-1784 to be precise), which have been working seamlessly for years on all other machines I have (VMWare images with different Windows versions, Raspberry Pi and Mac). Connecting the KVM with it's mouse and keyboard renders a working keyboard and a dead mouse (remember - switching to one of the other machines renders working keyboard and mouse instantly).... <rant on>pheeew, starting to get a bad feeling here. OBVIOUSLY we have a lot of cool hardware like USB 3 and DisplayPort and what not, but WHAT DOES THAT MATTER, when the Lenovo folks can't program this stuff properly?</rant off>
The W540 comes with a lot of Lenovo software. Much of it is really good and useful. But what happened when you try to log in to Windows? For some reason Lenovo want to inform you that the Num Lock is on when you see the standard login screen. The message something like "Num Lock is on - your password may be entered incorrectly". All in some black background, covering OVER the login field in Windows !!!! Hey, the laptop has a numeric keyboard, I don't need this message. Luckily others again have experience the same thing. At this page http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/New-T540p-numlock-warning-at-login/td-p/142... I get the tip that I need to rename the tpnumlk.exe to something else. Gone was the stupid message.
My advice to Lenovo - don't include stuff that harvest a lot of complaints and that obviously is going to annoy your customers. Even if the machine was one with a small keyboard and no separate numeric keyboard, I would NEVER EVER want to have some ugly black box covering over the standard login field… I can’t even imagine that the developer of this tool, use it (nor like it)! That is exactly why bloatware gets its reputation.
I would of course understand all this if I were talking about cheap machines and some wacko docking station. But I am not.... This is state-of-the-art, 2014, expensive-style laptop from the same manufacturer.
PS! At the end of this session, Lenovo tells me that there is a problem with the powersystem, and that it want to reduce power to sustainable levels....

can you connect the device in _*recovery mode*_ ?
JGG

Hooking up my late 2011 17 inch MacBook Pro to an ultra tv (4k resolution) for use as a monitor?

Hey! I am interested in hooking up my late 2011 17 inch MacBook Pro to an ultra tv (4k resolution). My computer has native 1920x1080 but can I reach 4k using that tv as a monitor? I plan on using a thunderbolt to HDMI adapter. Has anyone even tried this? I've heard rumors that the MacBook doesn't recognize that the tv has higher than 1920x1080 and so people use a hacked graphics card. It's all very confusing but if anyone has gotten this to work I'd be very interested in knowing how its done.

Any updates to this with latest Maveriks OSX upgrade 10.9?
I have an Active TB/HDMI adapter that coworker said he got to work with 4K Monitor at 3840.
Still trying to get a hold of him to validate his MBP model, but think it is the same as mine, Late 2011 MBP
All I am getting is 1920x1080 in options lisy with 10.9.2.

K7T Pro 2-A damaging CPUs

I have the most strange problem ever.
My MSI K7T Pro 2-A is damaging the CPUs I install for some unknown reason. The mobo has been rock stable for more than a year and a half and I think it is of excellent quality. About 15 days ago the PC froze while downloading a file under Win XP Pro, and then I had to shutdown. When I turned it on again, it makes 1 beep like everything was normal but the video signal was lost. Later, after many tries with different hardware I discovered that my Athlon 1 Ghz was burned; the strange thing is that doesn't had any external signs of burning, the surface was perfect. It was installed with a very good cooler (TITAN TTC-MT1AB) so temperature problems where discarded. Then I bought a new Duron 1.1 Ghz and installed it without problems. The BIOS installed was version 3.41. I flashed succesfully the same day I installed the new CPU to the BIOS last version (3.5) and it ran succesfully for about a week. Today, same story, the Duron was gone this time. My friend told me that maybe there is a sort of incompatibility with the new BIOS, but I refuse to believe it. Apparently the PSU is fine and I see no signs of a damaged capacitor or something like that in the mobo. We have absolutely no clue of what may be causing this; My technician friend tried to boot a Duron 700 Mhz and posted OK, but the new Duron don't posted anymore, after installing it on an older KT7 Pro 2, so I guess is damaged too. Any suggestion will be apreciated, as we try to isolate this problem. I will see if we use a electronic tester. If the PSU is the culprit, I don't understand how it doesn't burned the motherboard already, and if it is the mobo, I don't understand how a processor is running very stable for a week and then dyes. Any advice? I don't want to burn another CPU. ;(

Hi,
The motherboard isn't frieing CPU's, I'm pretty sure the old CPU is fine too....
RMA the board to MSI, as it happens on some boards and they need to be repaired.
Contact your dealer or your nearest MSI Quarters on what to do.
MSI warrants the board for 2 years, so that shouldn't be a problem.

K7T Pro and GeForce2 Ultra

Similar Messages

Maybe you are looking for