K7T Turbo LE and problems with IRQ routing Win98SE
When I boot my machine (AMD 1600+ on an MSI K7T Turbo Limited Edition), the BIOS reports me the following:
SiS6326 AGP card: NA (no IRQ even if I enable "Assign IRQ to VGA" in BIOS, but that's not my problem)
Startech NIC in slot 2: IRQ 11
D-Link DFE-538 TX in slot 3: IRQ 10
Echo Mia soundcard in slot 4: IRQ 5
Onboard Promise ATA100 controller: IRQ 11
2x USB controllers Via 3038: IRQ 3 for each one
IDE controllers: IRQ 14 and 15
In "Settings - Control Panel - System - Device Manager", there's one big difference:
The two USB controllers (Via 3038 PCI to USB) are on IRQ 10!!! The only way for Via USB controllers to be on their real good one IRQ (3) is to completely disable "IRQ Steering" in "Settings - Control Panel - System - Device Manager - System Devices - PCI Bus".
To resolve this, I tried:
- different Via 4 in 1 (4.32, 4.35, 4.36): no changes
- Via IRQ miniport uninstalled: no changes
- Enable "PnP OS" and "ACPI" in the BIOS: no changes
- Tried all the combinations in "Settings - Control Panel - System - Device Manager - System Devices - PCI Bus - IRQ Steering" (except disabling IRQ Steering because like I said, it resolves the bug. Though, I want IRQ Steering to be enabled AND the bug resolved).
So, if anyone have a clue, it will be really appreciated.
Thanks in advance.
gugusse
- MSI K7T Turbo Limited Edition
- Athlon XP 1600+ (1.4ghz)
- Win 98SE with all the patches
- NIC Startech (Realtek 8139 chip) in PCI 2 (IRQ 11)
- NIC D-Link DFE-538 Tx in PCI 3 (IRQ 10)
- Echo Mia in PCI 4 (IRQ 5)
- SiS 6326 AGP card (doesn't take an IRQ!)
- HDD Quantum Fireball Lct-10 20 GB 5400 rpm on IDE 1
- HDD Maxtor 6 L080J4 80 GB 7200 rpm on second IDE of the Promise controller (running in standard IDE mode, not RAID)
- Plextor 8/4/32 (master) and CD-ROM 56x Affrey (slave) on IDE 2
- 4 in 1 v.4.35
Quote
SiS6326 AGP card: NA (no IRQ even if I enable "Assign IRQ to VGA" in BIOS, but that's not my problem)
Just thought that I would let you know that I have the same troubles with no IRQ being assigned by the BIOS and due to this I am having troubles getting a DUAL monitor set up running!
--David
Similar Messages
-
I need advise and help with this problem .
First , I have been with Mac for many years ( 14 to be exact ) I do have some knowledge and understanding of Apple product .
At the present time I'm having lots of problems with the router so I was looking in to some info , and come across one web site regarding : port forwarding , IP addresses .
In my frustration , amongst lots of open web pages tutorials and other useless information , I come across innocent looking link and software to installed called Genieo , which suppose to help with any router .
Software ask for permission to install , and about 30 % in , my instinct was telling me , there is something not right . I stop installation . Delete everything , look for any
trace in Spotlight , Library . Nothing could be find .
Now , every time I open Safari , Firefox or Chrome , it will open in my home page , but when I start looking for something in steed of Google page , there is
''search.genieo.com'' page acting like a Google . I try again to get raid of this but I can not find solution .
With more research , again using genieo.com search eng. there is lots of articles and warnings . From that I learn do not use uninstall software , because doing this will install more things where it come from.
I do have AppleCare support but its to late to phone them , so maybe there some people with knowledge , how to get this of my computer
Any help is welcome , English is my learned language , you may notice this , so I'm not that quick with the respondGenieo definitely doesn't help with your router. It's just adware, and has no benefit to you at all. They scammed you so that they could display their ads on your computer.
To remove it, see:
http://www.thesafemac.com/arg-genieo/
Do not use the Genieo uninstaller! -
Problem with Advanced Routing in WRT320N
Hi, everybody.
First of all, sorry for my poor English.
I've a problem with Advanced Routing in router. My provider using routing and it looks like that:
route add -p 172.16.2.0 mask 255.255.255.0 10.1.0.2
route add -p 172.16.5.0 mask 255.255.255.0 10.1.0.2
route add -p 10.0.0.0 mask 255.0.0.0 10.1.0.2
Everything is working well in XP (or other OS), but then I try to setup a Routing in router:
1.
2.
I'm realy tired to flashing and reflashing between 1.00.02 and 1.00.03, changing browsers, and hard reseting.
Anybody'll gimme a shot trick to my tired brains?
Solved!
Go to Solution.1. Yes.
2. netstat:
C:\Users\dan>netstat -rn
===========================================================================
Список интерфейсов
31...........................inet
12...00 40 f4 76 95 bd ......VIA Rhine III Fast Ethernet адаптер
11...00 1d 92 2c 23 02 ......Realtek RTL8168B/8111B Family PCI-E Gigabit Ethern
et NIC (NDIS 6.20)
1...........................Software Loopback Interface 1
15...00 00 00 00 00 00 00 e0 Адаптер Microsoft 6to4 #2
21...00 00 00 00 00 00 00 e0 Адаптер Microsoft ISATAP #2
13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface
14...00 00 00 00 00 00 00 e0 Адаптер Microsoft 6to4
19...00 00 00 00 00 00 00 e0 Адаптер Microsoft ISATAP #3
18...00 00 00 00 00 00 00 e0 Адаптер Microsoft ISATAP
16...00 00 00 00 00 00 00 e0 Адаптер Microsoft 6to4 #3
20...00 00 00 00 00 00 00 e0 Адаптер Microsoft ISATAP #4
===========================================================================
IPv4 таблица маршрута
===========================================================================
Активные маршруты:
Сетевой адрес Маска сети Адрес шлюза Интерфейс Метрика
0.0.0.0 0.0.0.0 10.1.0.2 10.1.3.42 4501
0.0.0.0 0.0.0.0 On-link 91.203.178.26 21
10.0.0.0 255.0.0.0 10.1.0.2 10.1.3.42 4246
10.1.0.0 255.255.0.0 On-link 10.1.3.42 4501
10.1.3.42 255.255.255.255 On-link 10.1.3.42 4501
10.1.255.255 255.255.255.255 On-link 10.1.3.42 4501
91.203.178.26 255.255.255.255 On-link 91.203.178.26 276
127.0.0.0 255.0.0.0 On-link 127.0.0.1 4531
127.0.0.1 255.255.255.255 On-link 127.0.0.1 4531
127.255.255.255 255.255.255.255 On-link 127.0.0.1 4531
172.16.2.0 255.255.255.0 10.1.0.2 10.1.3.42 4246
172.16.2.10 255.255.255.255 10.1.0.2 10.1.3.42 4246
172.16.5.0 255.255.255.0 10.1.0.2 10.1.3.42 4246
224.0.0.0 240.0.0.0 On-link 127.0.0.1 4531
224.0.0.0 240.0.0.0 On-link 10.1.3.42 4502
224.0.0.0 240.0.0.0 On-link 91.203.178.26 21
255.255.255.255 255.255.255.255 On-link 127.0.0.1 4531
255.255.255.255 255.255.255.255 On-link 10.1.3.42 4501
255.255.255.255 255.255.255.255 On-link 91.203.178.26 276
===========================================================================
Постоянные маршруты:
Сетевой адрес Маска Адрес шлюза Метрика
172.16.2.0 255.255.255.0 10.1.0.2 1
172.16.5.0 255.255.255.0 10.1.0.2 1
10.0.0.0 255.0.0.0 10.1.0.2 1
===========================================================================
IPv6 таблица маршрута
===========================================================================
Активные маршруты:
Метрика Сетевой адрес Шлюз
16 1125 ::/0 2002:c058:6301::c058:6301
11 276 ::/0 fe80::f88b:9485:52cd:caaf
1 306 ::1/128 On-link
13 58 2001::/32 On-link
13 306 2001:0:4137:9e50:2846:3ccb:a434:4de5/128
On-link
16 1025 2002::/16 On-link
16 281 2002:5bcb:b21a::5bcb:b21a/128
On-link
11 276 fe80::/64 On-link
13 306 fe80::/64 On-link
13 306 fe80::2846:3ccb:a434:4de5/128
On-link
11 276 fe80::b9aa:b87b:89ea:fcdd/128
On-link
1 306 ff00::/8 On-link
13 306 ff00::/8 On-link
11 276 ff00::/8 On-link
===========================================================================
Постоянные маршруты:
Отсутствует
C:\Users\dan>
2. ipconfig:
C:\Users\dan>ipconfig /all
Настройка протокола IP для Windows
Имя компьютера . . . . . . . . . : druh
Основной DNS-суффикс . . . . . . :
Тип узла. . . . . . . . . . . . . : Гибридный
IP-маршрутизация включена . . . . : Нет
WINS-прокси включен . . . . . . . : Нет
Порядок просмотра суффиксов DNS . : mannet.lan
Адаптер PPP inet:
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : inet
Физический адрес. . . . . . . . . :
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
IPv4-адрес. . . . . . . . . . . . : 91.203.178.26(Основной)
Маска подсети . . . . . . . . . . : 255.255.255.255
Основной шлюз. . . . . . . . . : 0.0.0.0
DNS-серверы. . . . . . . . . . . : 91.190.68.2
91.203.177.4
NetBios через TCP/IP. . . . . . . . : Включен
Ethernet adapter lanHOME:
Состояние среды. . . . . . . . : Среда передачи недоступна.
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : VIA Rhine III Fast Ethernet адаптер
Физический адрес. . . . . . . . . : 00-40-F4-76-95-BD
DHCP включен. . . . . . . . . . . : Да
Автонастройка включена. . . . . . : Да
Ethernet adapter 1000LAN:
DNS-суффикс подключения . . . . . : mannet.lan
Описание. . . . . . . . . . . . . : Realtek RTL8168B/8111B Family PCI-E Gigab
it Ethernet NIC (NDIS 6.20)
Физический адрес. . . . . . . . . : 00-1D-92-2C-23-02
DHCP включен. . . . . . . . . . . : Да
Автонастройка включена. . . . . . : Да
Локальный IPv6-адрес канала . . . : fe80::b9aa:b87b:89ea:fcdd%11(Основной)
IPv4-адрес. . . . . . . . . . . . : 10.1.3.42(Основной)
Маска подсети . . . . . . . . . . : 255.255.0.0
Аренда получена. . . . . . . . . . : 17 октября 2009 г. 17:37:10
Срок аренды истекает. . . . . . . . . . : 18 октября 2009 г. 17:37:09
Основной шлюз. . . . . . . . . : fe80::f88b:9485:52cd:caaf%11
10.1.0.2
DHCP-сервер. . . . . . . . . . . : 172.16.2.2
IAID DHCPv6 . . . . . . . . . . . : 234888594
DUID клиента DHCPv6 . . . . . . . : 00-01-00-01-12-43-2B-71-00-1D-92-2C-23-02
DNS-серверы. . . . . . . . . . . : 172.16.2.2
Основной WINS-сервер. . . . . . . : 172.16.2.2
NetBios через TCP/IP. . . . . . . . : Включен
Туннельный адаптер Reusable Microsoft 6To4 Adapter:
Состояние среды. . . . . . . . : Среда передачи недоступна.
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : Адаптер Microsoft 6to4 #2
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
Туннельный адаптер Reusable ISATAP Interface {543B8BBE-84D2-471B-B8FB-F73600B4A8
2B}:
Состояние среды. . . . . . . . : Среда передачи недоступна.
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : Адаптер Microsoft ISATAP #2
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
Туннельный адаптер Подключение по локальной сети* 5:
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
IPv6-адрес. . . . . . . . . . . . : 2001:0:4137:9e50:2846:3ccb:a434:4de5(Осно
вной)
Локальный IPv6-адрес канала . . . : fe80::2846:3ccb:a434:4de5%13(Основной)
Основной шлюз. . . . . . . . . :
NetBios через TCP/IP. . . . . . . . : Отключен
Туннельный адаптер 6TO4 Adapter:
Состояние среды. . . . . . . . : Среда передачи недоступна.
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : Адаптер Microsoft 6to4
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
Туннельный адаптер isatap.mannet.lan:
Состояние среды. . . . . . . . : Среда передачи недоступна.
DNS-суффикс подключения . . . . . : mannet.lan
Описание. . . . . . . . . . . . . : Адаптер Microsoft ISATAP #3
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
Туннельный адаптер isatap.{AE6B314F-94BA-478F-8751-74DEB5AB1888}:
Состояние среды. . . . . . . . : Среда передачи недоступна.
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : Адаптер Microsoft ISATAP
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
Туннельный адаптер Подключение по локальной сети*:
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : Адаптер Microsoft 6to4 #3
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
IPv6-адрес. . . . . . . . . . . . : 2002:5bcb:b21a::5bcb:b21a(Основной)
Основной шлюз. . . . . . . . . : 2002:c058:6301::c058:6301
DNS-серверы. . . . . . . . . . . : 91.190.68.2
91.203.177.4
NetBios через TCP/IP. . . . . . . . : Отключен
Туннельный адаптер isatap.{8B513FFA-4355-406F-B999-1701EE42D5B9}:
Состояние среды. . . . . . . . : Среда передачи недоступна.
DNS-суффикс подключения . . . . . :
Описание. . . . . . . . . . . . . : Адаптер Microsoft ISATAP #4
Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP включен. . . . . . . . . . . : Нет
Автонастройка включена. . . . . . : Да
3.
4. without privider's cable:
4. with provider's cable: -
I have a RaspberryPi and I want to turn it into a router just for the hell of it. I've attempted this multiple times but always get stuck and say "screw it" since my roommates would bitch at me because they can't get on the internet. Now I live by myself and want to get it to work.
I've followed the Router page in the wiki but I only have internet access from the Pi itself. I had a few problems but I think I fixed them. My main problem now is that DHCP doesn't offer IP addresses. During bootup Arch tells me that it failed to start my private interface (eth0), while looking at the journal it says this because the interface is already up (don't know why) and it doesn't get an ip address. I would like to assign it a static address of 192.168.1.1 but I'm not sure how to do so.
If I set a static address for eth0 (my internal interface) and try to get an IP address from another computer it doesn't offer me one. If I set a static address on the other PC, I can ping the Pi from the PC and vice versa so I know that's good, but if I try to ping an external IP from the PC (such as Google's DNS server 8.8.8.8 which responds to pings) it gives me "destination host unreachable", yet I can ping it just fine from the Pi.
I'm using a Cisco E3200 router with Tomate by Shibby as a switch and WAP with the routing/DHCP/DNS features turned off. I don't believe that the E3200 is the problem.
Any suggestions on why this isn't working?
Last edited by brando56894 (2013-09-18 05:08:23)Thanks for the info, but I need to get DHCP working since I'm going to have a few other devices on the network that won't have static address (phones, tablets, friend's devices, etc...).
Lone_Wolf wrote:Off-topic : Don't think OP's problem is due to the different architecture, but deciding such things is part of the moderators job.
I was going to say that too, but I didn't want to poke the bear. My problems aren't really architecture dependent, they're just general networking problems.
Last edited by brando56894 (2013-09-18 17:57:36) -
I have problem with this router, when I connect to the internet wirelessly it works fine but when I try to connect my pc to router via cable I can't connect to the internet. maybe someone can help with this problem.
>> Posting Guide <<
-
Any new about updating lion to 10.7.4 and problems with bluetooth devices like Bose Soundlink Bluetooth Speaker?
Monroe
Just in the moment i updated to lion 10.7.4 my Bose Soundlink Bluetooth stop working as good as it was. I´m gonna try the update in the Bose web page. I hope it works -
Problems with Wireless Router and Adapter
I tried posting this in the wireless adapter forum but nobody responded :-(
I'm using a WRT54G Router btw, and the firmware is v2.02.7, Feb. 27, 2004.
Hi everyone,
I have a Linksys Wireless G Router and several computers that I try to connect with. One of them is a computer running Windows XP and using a Linksys Wireless USB B Adapter (WUSB11). Another is a laptop running Mandriva Linux using a Linksys Instant Wireless Network PC Card (WPC11). Another one is running Windows Vista and using a Linksys Wireless N card. I also have a laptop running Windows XP using a Linksys Wireless-G Notebook Adapter (WPC54G). I also have another PC running Windows XP and uses a Linksys Wireless USB Adapter WUSB54G. Finally, I have two macintosh laptops running OSX and with airport devices installed.
Anyway, I have problems with my internet connection frequently being interrupted and even sometimes I won't have a connection at all for hours. This occurs with my Linux laptop, the PC with the Wireless B Adapter, and the laptop using the Wireless G Notebook Adapter. In addition to this, the macintosh laptops have internet even more infrequently. However, I seem to never have a problem with the Windows Vista desktop or the Windows XP desktop that has the Wireless G adapter. I try repairing the connection and often it does not work. I have also tried resetting the router and the cable modem. I'm not sure what else I can do. I even bought a Wireless N router and had little success with that. We even went as far as moving the wireless router upstairs into our living room, thinking that the signal was somehow suffering from interference or that distance was a factor. Anyway, sorry for the long post but I could really use some help!
Thanks.Hi… logon to wireless N router’s setup page, open I.E. an in the address bar type 192.168.1.1 it would ask for username and password, put "admin" as a paassword (default password) without any username...linksys setup pops up, click on on wireless tab and and try changing radio band to wide 40MHz, wide channel to 9 and wireless standard channel to 1 or 11, go to advanced wireless settings reduce beacon interval to 50, fragmentation and RTS threshold to 2304, change N Transmission rate to 270 MBps…also try upgrading latest firmware on router, check whether it makes any difference or not and let me know.
-
Problems with my router cisco linksys wrt110 and my android cellphone and android table
i updated my router from 1.0 to 1.07 and one week later my phone and my tablet both with android 2.3(phone) 4.0(tablet) connect to the router wireless but don't navigate internet, they connect to google.com sometimes and if i do a search it bring it but if i try to open any of the search it doesn't open. and they connect to google play but doesn't download any app. if i open any app that needs to connect to internet it doesn't connect either. My wife has a blackberry phone and she doesn't have problem with internet connecting to the wifi router, i have a pc with windows 7 and connect wireless too and either connect to internet without problems. It's only happen with android. i download terminal app and i ping different web pages and respond by name and by ip but when i go to internet app and try to connect it doesn't bring the page. i don't have firewall and the firewall of the router i disble it but the problem persist.
i factory reset the router and my phone but problem persist. i set static ip and nothing. my cellphone and tablet connect to internet fine in others wifi routers. What else can i do? should i downgraded the firmware to the router? if it is so where can i download a previous version of the firmware and what are the steps to install it?If the other wireless devices are working fine connected to the router, then it might be that the Android phones and tablet needed to be configured properly. Had you tried to use another web browser on the problem phone and tablet to further isolate the issue? Had you tried to connect the phone and tablet to other wireless network and check if you still have the same issue? Please try to make sure that you are connected to the router’s main wireless network. And please try to delete preferred wireless networks, including your wireless network, on the phone and then try to reconnect.
Check this link for your reference:
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=ac433a5ab0944f4e9f43338a8dd32465_Removing_a_networ... -
Wireless printing problems with Asus router RT-N56U and HP8500
Neew MacBookPro with Lion. Also have HP 8500a 909a printer hooked up to an Asus router RT-N56U Google search indicates MANY problems with HP printers being used with wireless Mac, even with Airport. Of course we know HP is one of the worse customer support companies on earth,, so I came here in hopes to find a solution. I updated my mac and firmware for router. The Mac doesn't find any printers wirelessly at all. If I hook up with a cable it works fine.. Thanks
I own the RT-N56U (best router on the market hands-down), along with an HP LaserJet 1320, however it's connected via USB to my computer instead of the router. While it's true that HP don't have a terrific support record for Mac drivers in fairness it may be the Asus router causing the problem; if you Google "Asus RT-N56U" and "mac os x print server", you'll find complaints similar to yours from other users. From what I understand this is partly dependent on your printer and whether it supports network printing, and partly on compliance with the Asus router firmware. I Googled what appears to be a possible solution to configuring the Asus print server, however I haven't yet tested this myself:
http://forums.techarena.in/networking-security/1424669.htm#post5384770 -
Site to Site VPN Problems With 2801 Router and ASA 5505
Hello,
I am having some issue setting up a site to site ipsec VPN between a Cisco 2801 router and a Cisco ASA 5505. I was told there was a vpn previously setup with an old hosting provider, but those connections have been servered. Right now I am trying to get the sites to talk to the 2801. Here ere are my current configs, please let me know if you need anything else. Im stumped on this one. Thanks.
IP scheme at SIte A:
IP 172.19.3.x
sub 255.255.255.128
GW 172.19.3.129
Site A Ciscso 2801 Router
Current configuration : 11858 bytes
version 12.4
service timestamps debug datetime localtime
service timestamps log datetime localtime show-timezone
service password-encryption
hostname router-2801
boot-start-marker
boot-end-marker
logging message-counter syslog
logging buffered 4096
aaa new-model
aaa authentication login userauthen group radius local
aaa authorization network groupauthor local
aaa session-id common
clock timezone est -5
clock summer-time zone recurring last Sun Mar 2:00 1 Sun Nov 2:00
dot11 syslog
ip source-route
ip dhcp excluded-address 172.19.3.129 172.19.3.149
ip dhcp excluded-address 172.19.10.1 172.19.10.253
ip dhcp excluded-address 172.19.3.140
ip dhcp ping timeout 900
ip dhcp pool DHCP
network 172.19.3.128 255.255.255.128
default-router 172.19.3.129
domain-name domain.local
netbios-name-server 172.19.3.7
option 66 ascii 172.19.3.225
dns-server 172.19.3.140 208.67.220.220 208.67.222.222
ip dhcp pool VoiceDHCP
network 172.19.10.0 255.255.255.0
default-router 172.19.10.1
dns-server 208.67.220.220 8.8.8.8
option 66 ascii 172.19.10.2
lease 2
ip cef
ip inspect name SDM_LOW cuseeme
ip inspect name SDM_LOW dns
ip inspect name SDM_LOW ftp
ip inspect name SDM_LOW h323
ip inspect name SDM_LOW https
ip inspect name SDM_LOW icmp
ip inspect name SDM_LOW imap
ip inspect name SDM_LOW pop3
ip inspect name SDM_LOW netshow
ip inspect name SDM_LOW rcmd
ip inspect name SDM_LOW realaudio
ip inspect name SDM_LOW rtsp
ip inspect name SDM_LOW esmtp
ip inspect name SDM_LOW sqlnet
ip inspect name SDM_LOW streamworks
ip inspect name SDM_LOW tftp
ip inspect name SDM_LOW tcp
ip inspect name SDM_LOW udp
ip inspect name SDM_LOW vdolive
no ip domain lookup
ip domain name domain.local
multilink bundle-name authenticated
key chain key1
key 1
key-string 7 06040033484B1B484557
crypto pki trustpoint TP-self-signed-3448656681
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3448bb6681
revocation-check none
rsakeypair TP-self-signed-344bbb56681
crypto pki certificate chain TP-self-signed-3448656681
certificate self-signed 01
3082024F
quit
username admin privilege 15 password 7 F55
archive
log config
hidekeys
crypto isakmp policy 10
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key XXXXX address 209.118.0.1
crypto isakmp key xxxxx address SITE B Public IP
crypto isakmp keepalive 40 5
crypto isakmp nat keepalive 20
crypto isakmp client configuration group IISVPN
key 1nsur3m3
dns 172.19.3.140
wins 172.19.3.140
domain domain.local
pool VPN_Pool
acl 198
crypto isakmp profile IISVPNClient
description VPN clients profile
match identity group IISVPN
client authentication list userauthen
isakmp authorization list groupauthor
client configuration address respond
crypto ipsec transform-set myset esp-3des esp-md5-hmac
crypto dynamic-map Dynamic 5
set transform-set myset
set isakmp-profile IISVPNClient
qos pre-classify
crypto map VPN 10 ipsec-isakmp
set peer 209.118.0.1
set peer SITE B Public IP
set transform-set myset
match address 101
qos pre-classify
crypto map VPN 65535 ipsec-isakmp dynamic Dynamic
track 123 ip sla 1 reachability
delay down 15 up 10
class-map match-any VoiceTraffic
match protocol rtp audio
match protocol h323
match protocol rtcp
match access-group name VOIP
match protocol sip
class-map match-any RDP
match access-group 199
policy-map QOS
class VoiceTraffic
bandwidth 512
class RDP
bandwidth 768
policy-map MainQOS
class class-default
shape average 1500000
service-policy QOS
interface FastEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0$$FW_INSIDE$
ip address 172.19.3.129 255.255.255.128
ip access-group 100 in
ip inspect SDM_LOW in
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/0.10
description $ETH-VoiceVLAN$$
encapsulation dot1Q 10
ip address 172.19.10.1 255.255.255.0
ip inspect SDM_LOW in
ip nat inside
ip virtual-reassembly
interface FastEthernet0/1
description "Comcast"
ip address PUB IP 255.255.255.248
ip access-group 102 in
ip inspect SDM_LOW out
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map VPN
interface Serial0/1/0
description "Verizon LEC Circuit ID: w0w13908 Site ID: U276420-1"
bandwidth 1536
no ip address
encapsulation frame-relay IETF
frame-relay lmi-type ansi
interface Serial0/1/0.1 point-to-point
bandwidth 1536
ip address 152.000.000.18 255.255.255.252
ip access-group 102 in
ip verify unicast reverse-path
ip inspect SDM_LOW out
ip nat outside
ip virtual-reassembly
frame-relay interface-dlci 500 IETF
crypto map VPN
service-policy output MainQOS
interface Serial0/2/0
description "PAETEC 46.HCGS.788446.CV (Verizon ID) / 46.HCGS.3 (PAETEC ID)"
ip address 123.252.123.102 255.255.255.252
ip access-group 102 in
ip inspect SDM_LOW out
ip nat outside
ip virtual-reassembly
encapsulation ppp
crypto map VPN
service-policy output MainQOS
ip local pool VPN_Pool 172.20.3.130 172.20.3.254
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 50.00.000.110 track 123
ip route 0.0.0.0 0.0.0.0 111.252.237.000 254
ip route 122.112.197.20 255.255.255.255 209.252.237.101
ip route 208.67.220.220 255.255.255.255 50.78.233.110
no ip http server
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip flow-top-talkers
top 20
sort-by bytes
ip nat inside source route-map COMCAST interface FastEthernet0/1 overload
ip nat inside source route-map PAETEC interface Serial0/2/0 overload
ip nat inside source route-map VERIZON interface Serial0/1/0.1 overload
ip nat inside source static tcp 172.19.3.140 21 PUB IP 21 extendable
ip access-list extended VOIP
permit ip 172.20.3.0 0.0.0.127 host 172.19.3.190
permit ip host 172.19.3.190 172.20.3.0 0.0.0.127
ip radius source-interface FastEthernet0/0
ip sla 1
icmp-echo 000.67.220.220 source-interface FastEthernet0/1
timeout 10000
frequency 15
ip sla schedule 1 life forever start-time now
access-list 23 permit 172.19.3.0 0.0.0.127
access-list 23 permit 172.19.3.128 0.0.0.127
access-list 23 permit 173.189.251.192 0.0.0.63
access-list 23 permit 107.0.197.0 0.0.0.63
access-list 23 permit 173.163.157.32 0.0.0.15
access-list 23 permit 72.55.33.0 0.0.0.255
access-list 23 permit 172.19.5.0 0.0.0.63
access-list 100 remark "Outgoing Traffic"
access-list 100 deny ip 67.128.87.156 0.0.0.3 any
access-list 100 deny ip host 255.255.255.255 any
access-list 100 deny ip 127.0.0.0 0.255.255.255 any
access-list 100 permit tcp host 172.19.3.190 any eq smtp
access-list 100 permit tcp host 172.19.3.137 any eq smtp
access-list 100 permit tcp any host 66.251.35.131 eq smtp
access-list 100 permit tcp any host 173.201.193.101 eq smtp
access-list 100 permit ip any any
access-list 100 permit tcp any any eq ftp
access-list 101 remark "Interesting VPN Traffic"
access-list 101 permit ip 172.19.3.128 0.0.0.127 172.19.3.0 0.0.0.127
access-list 101 permit ip 172.20.3.128 0.0.0.127 172.19.3.0 0.0.0.127
access-list 101 permit ip 172.19.3.128 0.0.0.127 host 172.19.250.10
access-list 101 permit ip 172.19.3.128 0.0.0.127 host 172.19.250.11
access-list 101 permit tcp any any eq ftp
access-list 101 permit tcp any any eq ftp-data
access-list 102 remark "Inbound Access"
access-list 102 permit udp any host 152.179.53.18 eq non500-isakmp
access-list 102 permit udp any host 152.179.53.18 eq isakmp
access-list 102 permit esp any host 152.179.53.18
access-list 102 permit ahp any host 152.179.53.18
access-list 102 permit udp any host 209.000.000.102 eq non500-isakmp
access-list 102 permit udp any host 209.000.000.102 eq isakmp
access-list 102 permit esp any host 209.000.000.102
access-list 102 permit ahp any host 209.000.000.102
access-list 102 permit udp any host PUB IP eq non500-isakmp
access-list 102 permit udp any host PUB IP eq isakmp
access-list 102 permit esp any host PUB IP
access-list 102 permit ahp any host PUB IP
access-list 102 permit ip 72.55.33.0 0.0.0.255 any
access-list 102 permit ip 107.0.197.0 0.0.0.63 any
access-list 102 deny ip 172.19.3.128 0.0.0.127 any
access-list 102 permit icmp any any echo-reply
access-list 102 permit icmp any any time-exceeded
access-list 102 permit icmp any any unreachable
access-list 102 permit icmp any any
access-list 102 deny ip any any log
access-list 102 permit tcp any host 172.19.3.140 eq ftp
access-list 102 permit tcp any host 172.19.3.140 eq ftp-data established
access-list 102 permit udp any host SITE B Public IP eq non500-isakmp
access-list 102 permit udp any host SITE B Public IP eq isakmp
access-list 102 permit esp any host SITE B Public IP
access-list 102 permit ahp any host SITE B Public IP
access-list 110 remark "Outbound NAT Rule"
access-list 110 remark "Deny VPN Traffic NAT"
access-list 110 deny ip 172.19.3.128 0.0.0.127 172.19.3.0 0.0.0.127
access-list 110 deny ip 172.19.3.128 0.0.0.127 172.19.10.0 0.0.0.255
access-list 110 deny ip 172.19.10.0 0.0.0.255 172.19.3.128 0.0.0.127
access-list 110 deny ip 172.20.3.128 0.0.0.127 172.19.3.0 0.0.0.127
access-list 110 deny ip 172.19.3.128 0.0.0.127 172.20.3.128 0.0.0.127
access-list 110 deny ip 172.19.3.128 0.0.0.127 host 172.19.250.11
access-list 110 deny ip 172.19.3.128 0.0.0.127 host 172.19.250.10
access-list 110 permit ip 172.19.3.128 0.0.0.127 any
access-list 110 permit ip 172.19.10.0 0.0.0.255 any
access-list 198 remark "Networks for IISVPN Client"
access-list 198 permit ip 172.19.3.0 0.0.0.127 172.20.3.128 0.0.0.127
access-list 198 permit ip 172.19.3.128 0.0.0.127 172.20.3.128 0.0.0.127
access-list 199 permit tcp any any eq 3389
route-map PAETEC permit 10
match ip address 110
match interface Serial0/2/0
route-map COMCAST permit 10
match ip address 110
match interface FastEthernet0/1
route-map VERIZON permit 10
match ip address 110
match interface Serial0/1/0.1
snmp-server community 123 RO
radius-server host 172.19.3.7 auth-port 1645 acct-port 1646 key 7 000000000000000
control-plane
line con 0
line aux 0
line vty 0 4
access-class 23 in
privilege level 15
transport input telnet ssh
line vty 5 15
access-class 23 in
privilege level 15
transport input telnet ssh
scheduler allocate 20000 1000
ntp server 128.118.25.3
ntp server 217.150.242.8
end
IP scheme at site B:
ip 172.19.5.x
sub 255.255.255.292
gw 172.19.5.65
Cisco ASA 5505 at Site B
ASA Version 8.2(5)
hostname ASA5505
domain-name domain.com
enable password b04DSH2HQqXwS8wi encrypted
passwd b04DSH2HQqXwS8wi encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 172.19.5.65 255.255.255.192
interface Vlan2
nameif outside
security-level 0
ip address SITE B public IP 255.255.255.224
boot system disk0:/asa825-k8.bin
ftp mode passive
clock timezone est -5
clock summer-time zone recurring last Sun Mar 2:00 last Sun Oct 2:00
dns server-group DefaultDNS
domain-name iis-usa.com
same-security-traffic permit intra-interface
object-group network old hosting provider
network-object 72.55.34.64 255.255.255.192
network-object 72.55.33.0 255.255.255.0
network-object 173.189.251.192 255.255.255.192
network-object 173.163.157.32 255.255.255.240
network-object 66.11.1.64 255.255.255.192
network-object 107.0.197.0 255.255.255.192
object-group network old hosting provider
network-object host 172.19.250.10
network-object host 172.19.250.11
access-list 100 extended permit ip 172.19.5.64 255.255.255.192 object-group old hosting provider
access-list 100 extended permit ip 172.19.5.64 255.255.255.192 172.19.3.128 255.255.255.128
access-list 10 extended deny ip 0.0.0.0 255.0.0.0 any
access-list 10 extended deny ip 127.0.0.0 255.0.0.0 any
access-list 10 extended deny ip 169.254.0.0 255.255.0.0 any
access-list 10 extended deny ip 172.16.0.0 255.255.0.0 any
access-list 10 extended deny ip 224.0.0.0 224.0.0.0 any
access-list 10 extended permit icmp any any echo-reply
access-list 10 extended permit icmp any any time-exceeded
access-list 10 extended permit icmp any any unreachable
access-list 10 extended permit icmp any any traceroute
access-list 10 extended permit icmp any any source-quench
access-list 10 extended permit icmp any any
access-list 10 extended permit tcp object-group old hosting provider any eq 3389
access-list 10 extended permit tcp any any eq https
access-list 10 extended permit tcp any any eq www
access-list 110 extended permit ip 172.19.5.64 255.255.255.192 172.19.3.0 255.255.255.128
access-list 110 extended permit ip 172.19.5.64 255.255.255.192 object-group old hosting provider
pager lines 24
logging enable
logging timestamp
logging console emergencies
logging monitor emergencies
logging buffered warnings
logging trap debugging
logging history debugging
logging asdm informational
mtu inside 1500
mtu outside 1500
ip verify reverse-path interface inside
ip verify reverse-path interface outside
ip audit name jab attack action alarm drop reset
ip audit name probe info action alarm drop reset
ip audit interface outside probe
ip audit interface outside jab
ip audit info action alarm drop reset
ip audit attack action alarm drop reset
ip audit signature 2000 disable
ip audit signature 2001 disable
ip audit signature 2004 disable
ip audit signature 2005 disable
icmp unreachable rate-limit 1 burst-size 1
icmp permit 75.150.169.48 255.255.255.240 outside
icmp permit 72.44.134.16 255.255.255.240 outside
icmp permit 72.55.33.0 255.255.255.0 outside
icmp permit any outside
icmp permit 173.163.157.32 255.255.255.240 outside
icmp permit 107.0.197.0 255.255.255.192 outside
icmp permit 66.11.1.64 255.255.255.192 outside
icmp deny any outside
asdm image disk0:/asdm-645.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list 100
nat (inside) 1 0.0.0.0 0.0.0.0
access-group 10 in interface outside
route outside 0.0.0.0 0.0.0.0 174.78.151.225 1
timeout xlate 3:00:00
timeout conn 24:00:00 half-closed 0:10:00 udp 0:10:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 24:00:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http 107.0.197.0 255.255.255.192 outside
http 66.11.1.64 255.255.255.192 outside
snmp-server host outside 107.0.197.29 community *****
snmp-server host outside 107.0.197.30 community *****
snmp-server host inside 172.19.250.10 community *****
snmp-server host outside 172.19.250.10 community *****
snmp-server host inside 172.19.250.11 community *****
snmp-server host outside 172.19.250.11 community *****
snmp-server host outside 68.82.122.239 community *****
snmp-server host outside 72.55.33.37 community *****
snmp-server host outside 72.55.33.38 community *****
snmp-server host outside 75.150.169.50 community *****
snmp-server host outside 75.150.169.51 community *****
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map VPNMAP 10 match address 110
crypto map VPNMAP 10 set peer 72.00.00.7 old vpn public ip Site B Public IP
crypto map VPNMAP 10 set transform-set ESP-3DES-MD5
crypto map VPNMAP 10 set security-association lifetime seconds 86400
crypto map VPNMAP 10 set security-association lifetime kilobytes 4608000
crypto map VPNMAP interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 20
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet 172.19.5.64 255.255.255.192 inside
telnet 172.19.3.0 255.255.255.128 outside
telnet timeout 60
ssh 0.0.0.0 0.0.0.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 60
console timeout 0
management-access inside
dhcpd dns 172.19.3.140
dhcpd wins 172.19.3.140
dhcpd ping_timeout 750
dhcpd domain iis-usa.com
dhcpd address 172.19.5.80-172.19.5.111 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection scanning-threat shun except object-group old hosting provider
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
ntp server 128.118.25.3 source outside
ntp server 217.150.242.8 source outside
tunnel-group 72.00.00.7 type ipsec-l2l
tunnel-group 72.00.00.7 ipsec-attributes
pre-shared-key *****
tunnel-group old vpn public ip type ipsec-l2l
tunnel-group old vpn public ip ipsec-attributes
pre-shared-key *****
tunnel-group SITE A Public IP type ipsec-l2l
tunnel-group SITE A Public IP ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect netbios
inspect tftp
inspect pptp
inspect sip
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:
: endI have removed the old "set peer" and have added:
IOS router:
access-list 101 permit ip 172.19.3.128 0.0.0.127 172.19.5.64 0.0.0.65
ASA fw:
access-list 110 extended permit ip 172.19.5.64 255.255.255.192 172.19.3.128 255.255.255.128
on the router I have also added;
access-list 110 deny ip 172.19.3.128 0.0.0.127 172.19.5.64 0.0.0.63
Here is my acl :
access-list 110 remark "Outbound NAT Rule"
access-list 110 remark "Deny VPN Traffic NAT"
access-list 110 deny ip 172.19.3.128 0.0.0.127 172.19.3.0 0.0.0.127
access-list 110 deny ip 172.19.3.128 0.0.0.127 172.19.10.0 0.0.0.255
access-list 110 deny ip 172.19.10.0 0.0.0.255 172.19.3.128 0.0.0.127
access-list 110 deny ip 172.20.3.128 0.0.0.127 172.19.3.0 0.0.0.127
access-list 110 deny ip 172.19.3.128 0.0.0.127 172.20.3.128 0.0.0.127
access-list 110 deny ip 172.19.3.128 0.0.0.127 host 172.19.250.11
access-list 110 deny ip 172.19.3.128 0.0.0.127 host 172.19.250.10
access-list 110 permit ip 172.19.3.128 0.0.0.127 any
access-list 110 permit ip 172.19.10.0 0.0.0.255 any
access-list 110 deny ip 172.19.3.128 0.0.0.127 172.19.5.64 0.0.0.63
access-list 198 remark "Networks for IISVPN Client"
access-list 198 permit ip 172.19.3.0 0.0.0.127 172.20.3.128 0.0.0.127
access-list 198 permit ip 172.19.3.128 0.0.0.127 172.20.3.128 0.0.0.127
Still no ping tothe other site. -
Bear with me please as I have never used the community before. I have an Airport Extreme 1st generation at least I think it is a 1st generation. My PC is hardwired and my Mac Pro, obviously wireless. I have 50/8 mbps service but the speeds on my PC run around 20/8 and 30/8 on the Mac. Cable says it is a problem with the airport since my PC speeds rise to 50 when the airport is disconnected. Does anyone know what to do?
The simplest way would be to perform a "soft" reset on the AEBS. This type of reset will temporarily disable all of the AEBS's passwords up to five minutes. This should give you ample time to access the AEBS with the AirPort Utility to change it.
If you don't want to actually change the password, then you can possibly retrieve the password from the OS X Keychain, as follows:
Run the Keychain Access utility found in \Applications\Utilities
In the category column (on the left side of the utilities' window), select "All Items."
In the right column look for your Network Name. It will have a "Kind" of "AirPort network password."
Double-click on your network name listing.
Click on "Show password."
Enter your Mac's administrator's password
Your wireless network's password should now be displayed. -
My Mac book pro is 15 months old and now suddenly it has started resetting the date and time, causing problems with applications and my wireless access. Any suggestions as to why this is happening and how to fix it?
Seems the time isn't being saved to your computer correctly, it may be a corrupt file that isn't saving the time anymore.
You can move the
com.apple.systempreferences.plist
file out of your Users/Library/Preferences folder to the desktop and reboot.
then go to your System Preferences > Date and Time and set a time server close to your location (or in your time zone)
(trash the file on the desktop if no ill issues occur later on)
or you can follow/bookmark these support docs to reset your PRAM and SMC (and for future reference)
http://support.apple.com/kb/TS2570
http://support.apple.com/kb/TS1440
http://support.apple.com/kb/HT1455
http://support.apple.com/kb/ht3964
http://support.apple.com/kb/HT1379
http://support.apple.com/kb/ht1379
http://support.apple.com/kb/HT1509
I don't remember exactly where OS X is keeping it time settings now, but I think one of those choices should help resolve your issue and won't hurt anything giving them a shot. Perhaps someone else could refresh my memory. -
K7T Turbo LE IDE problem?
Hi,
I'm stuck here. I have an AMD Athlon 1400/266 (T-bird) running on the K7T Turbo Limited Edition mainboard, BIOS version 3.6. 512 MB PC133 SDRAM. 2 Maxtor HD's. My system is about 2 years old.
In the last 2 months, the following has started to happen:
Occasionally (say, 1 out of 10 attempts), my PC won't boot (DISK_BOOT_FAILURE). I know this in advance because when it happens, it gives two short beeps when powered up (can't find the meaning of them :O ).
The problem is: sometimes the Primary Master is gone ("none"), but other times, it's the primary slave. In that case, the PC will boot but behaves very strange once WinXP is started. And sometimes, both master and slave show up as "None" ?(
The optical drives on IDE2 are detected at all times.
D-Bracket is all green. I reseated the IDE cable with no result. Tested both the Maxtor HD's, no errors.
So, what now? Any ideas?
Thanks,
DennisJust came back from my holiday so I ran some more tests.
First, I checked the drives one at a time using the PowerMax utility. 81GB slave is fine (tested alone).
40GB master is fine 9 out of 10, 10th time it says "Please Perform extended diagnostics" and then it reports "Congratulations, your drive passed all tests!"
A little weird....
Looks like failing drive, but could this also be IDE controller communication failure?
I also tried replacing the 80pin IDE cable with a 40pin cable which is brand new. This makes no difference other than slower system speed.
Maxtor website has no info, MSI same story.
Now what??? ;( -
I've got a ms-6330 K7T Turbo limited edition board. I've been running a 900mhz Duron for years in this board with no problems. I recently bought an XP1800+ (palomino). I upgraded to the newest version BIOS, changed the jumper for the 133 FSB and installed the CPU. The first power-up it hung on the post screen. After that, I got nothing. The D-led shows it is hanging at processor initialization. Put my Duron back in and it works fine.
I bought the processor off Ebay and realize this may be my problem. But it was from a reputable seller. Is there something else I could try before trying to contact the seller for a replacement? I wish I had another socket A board to try it in, but I don't.Are you 100% sure you recieved a Palomino core?
You can refer to this chart, and compare the CPU to the pictures, to verify that it is a palomino core.
Also, insure the the heatsink is properly seated, as they will fit the wrong way, but will not make good contact with the CPU.
Did you use fresh thermal grease on the heatsink?
PC133 is required to use a 133FSB.
Try clearing the CMOS, and see if that will allow it to boot. -
K7t turbo won't boot with xp1800+
I'm tyring to do an upgrade from my 1.4 tbird to a xp1800+ palomino. I have 2 sticks of pc133 crucial ram and a 300W sparkle psu. I've been running at 133 the entire time i've had the 1.4 cpu.
the bios will detect the 1800+ fine, but the computer always reboots when it gets to the "Starting windows xp" screen
what could be the problem?Hi
I have also bought a new cpu (XP1800+) for my K7T Turbo and the day before I upgraded the cpu I updated the bios from 3.2 to 3.6
Then I upgraded the cpu, and have a lot of trouble!
The machine stops all kinds of places, it is very hard/tricky to turn it on, some times I need to restart it serveral times.
The led displays (D-LED) comes with different failure from stopping at early chipset initialization to testing vga bios and initializing keyboard controller.
I found that the default VCore is not the 1.750V as required by the XP1800+ and that the motherboard only supports VCore = 1.700V, set this by manual.
Then remember to remove the jumper on the board to work with cpu's at 133FSB.
These things helped me a lot, but my machine was still very unstable.
I have now downgraded my BIOS to ver. 3.2 and testet it for one day, and have not experienced any kind of problem, except that it does not recognize my cpu as a XP1800+ but runs at 1533 MHz
I think, that theres a bug in the BIOS ver. 3.6 for the motherboard! ??
This is also showed by the problems did'nt stop when I changed my cpu back to the old TB1000, and had the same problems as with the XP1800+
So my advise:
- set the VCore manually
- remove the jumper
- downgrade your bios
I have plans to upgrade my bios 0.1 version at a time, until it becomes unstable, and then go 0.1 version back.
Im writing a new thread on this subject to, where I will also write about my experince about the bios upgrades.
Good Luck!
Regards
Ronni
Maybe you are looking for
-
Best practice for setting or detecting screen size?
Hi All, Trying to determine a best practice for setting or detecting the screen size. For playbook and iOS, I can set them. But for Android, the number of devices is too large so I'd rather detect. My first choice is to use the stage.stageHeight and
-
Any software can run J2ME in Pocket PC 2003?
I found that there are some software can support J2ME in PPC 2002. As I want to upgrad to PPC2003, any JVM can support J2ME in this OS. Thanks a lot.
-
I upgraded to Tiger finally. Upgraded to Final Cut Studio as well. After the upgrades, all Adobe Products decided to quit working. Also, DVD Studio Pro won't work either. System Information: - Dual 2.5 GHz PowerPC G5, 4 GB DDR SDRAM, Running 10.4.6 w
-
Does Acrobat support KSP?
I have a question about SHA-256 signature in AcrobatX. I tried SHA-256 electronic signature to a PDF file using Acrobat on Windows 7. In Acrobat XI, I could create electronic signature with SHA-256 by KSP. However, in Acrobat X, I received the follow
-
Stuck on panic when started up
when i try yo start up the powerbook it goes to a kernel screen unable to find driver can anyone help me?