K7t Turbo2 and an AMD Athlon XP 2600+

I recently flashed the BIOS on my K7t Turbo2 board to the 3.6 version which supports AMD Athlon XP processors up to 2600+. However, after I installed the new cpu, set the core voltage to 1.65, the multiplier to 11.5 and the DCM value to 166 the computer would not boot. Instead I received a simple "Beep" then two to three seconds later, another "Beep." This continues to no avail and it takes almost ten "hard reboots" which is killing my hard disks to even get back into the BIOS configuration, wherein I modified the DCM settings to 133 instead of 166. Now the computer boots but continues to tell me:
Unknown Processor at 1533mhz
When I did get it to run at 1910mhz (notice 1910, not 1917 as it should be), it also said Unknown Processor. Then, on one of the three ocassions I was actually able to boot the computer at the higher clock speed, none of my drives appeared. On the second ocassion, the Linux boot process froze and on the third, Windows XP wouldn't boot. Now, if anyone has any suggestions as to what BIOS settings I can try, or even resetting my BIOS to a previous version, then trying to reflash it, that would be great.... If, however, this is more of an issue with an MSI BIOS patch, please release another version that works. Thanks much!
-Adam

Go with the Tbred 2400+ bud, Thats what i have at the mo in my KT3 Ultra 2C, and with my old MSI ti4200 with 128mb, it kept up with a K7N2 Delta ILSR which is running a Barton 2600+ and an MSI FX5600XT with 256mb (that rig only beats me on the extra test in 2001se and 2003 that the FX card covers).
Cant wait for my K7N2 Delta ILSR to arrive to go with my Ti4600.
Should happily blow the Barton rig away

Similar Messages

K7T Turbo2 and Athlon XP 2600 / 333 BIOS settings ?

Hi,
Does anyone have any experience with this combo ?
I've tried to install the processor but I can't achieve 2600 Mhz...only 1600 Mhz !
Any ideas ?
---> MSI K7T Turbo2 (latest BIOS)
---> AMD Athlon XP 2600+ FSB 333 BOX
Jumper J17 (i think) is out.
Thanks,
m@ndr@ke

Unfortunately Bogdan2003 is right, your board only supports a 266MHz FSB. The XP 2600 doesn't run at 2600MHz, it comes in two flavours one runs at 2083MHz which is the 333FSB version and one at 2133MHz which is the 266FSB version, the later being the one your board will support.

Are the K7T Turbo2 and MS-6330 V5 the same MoBo

Please some one help!!!!!!!!!!!!!!!
I have a motherboard and on the motherboard the text say MS-6330 V5 and all i can find on msi homepage is a K7T Turbo2 MS-6330 v5 so is my mobo a k7t turbo2 ???????
i am lost............ ?(
i flashed my bios at my own risk with the newest bios for k7t turbo2 and it works well as hell so my thought is that my ms-6330 v5 really are a k7t turbo2 am i right ??

Hmm, I think 'MS-6330 V5' is the same as 'MS-6330 v5'... :D
So go on and buy your new cpu.

Need help w/ K7T Turbo2 and mobile Athlon 2600+/266

Hi.
I just bought a new Mobile Athlon 2600+/266 and can't quite get it to work right in my trusty Turbo2. It shows up during post as "Unknow CPU 800MHz", which is a little disappointing. (it is stable at this speed, though) My previous chip in this same board was an Athlon 1200/266 (A1200AMS3C), so everything worked at 133/266 before.
I've updated the BIOS to the most recent, checked that J17 is clear, stripped the box down to cpu + hd + 1 stick ram, and still no dice. All of my CMOS voltage/peripheral settings are at default.
The voltage/frequency menu in the BIOS correctly detects the chipset at 133MHz. When I tried to manually bump the freq multiplier to 15x, I actually saw a decrease in reported processor down to "Unknow CPU 733MHz". When I knocked it down to 14x, it dropped proportionally (to 667, I think). This makes me think that the freq multipler is correct at default, and that it's something else that's going wrong. I don't know what, though.
Is the problem that the chip is Mobile? My last guess is to try to up the voltage, but I didn't want to melt anything before checking with some experts.
I'm not looking for overclocking, just to get it running the 2.133 GHz that it was advertised at.
Thanks much,
-Clint
System specs:
Mobile AMD 2600+/266
K7T Turbo2 (latest BIOS)
ANTEC 350W model PP-352X
2x Micron 256MB PC133 (48lc32m4a2)

Does that board have a BIOS setting for FSB, as well as having the J17 jumper? I know a couple people with those boards, but never played in the BIOS to see. It sounds like it is actually trying to use 66MHz X 14, 15 or whatever Multiplier you are setting. Those Mobile chips are not Multi-locked like the normal CPUs are, and may be next to impossible to get set up on these older boards.

K7T turbo2 and Athlon 2600+

HI ALL!
I just updated my bios t V 3,6 and put an AMD Athlon 2600+ on the MB.
When the computor boots up it show that ther´s a 2000 instead.
Enybody know why?
Thanks ADDE

Quote
Originally posted by sorman
Toock the fan away to look, but the lable on the CPU doesn´t say.
Edit:
Does the speed of the memory make eny difference, mine is 133
ADDE
XP2600/266 works great on my T2. To make sure of which FSB you have, check the last letter of the top line of info on the CPU. If C then its a 133/266 model, if D then its a 166/333 model.
Your meyory should be fine. Whats the specs on your power supply, and are you absolutely sure you have the heatsink mounted correctly?

K7T Turbo2 and new Athlon 1700

Hello!
I have a K7T Turbo 2 motherboard with an AMD Duron 1200, which ran fine. I recently purchased AN AMD Athlon 1700+ so that I could take advantage of the 133 FSB on the board rather than the 100 FSB of the Duron.
The first thin I did was flash the Bios to version 3.4. I then removed the J17 jumper on the board to run at 133fsb. When I first restarted the computer, everything seemed to be fine. Then I started to receive an error message that stated “Pagefault_in_nonpaged_area” and had to reset. Sometimes I received the message after a full boot and others while booting and became more frequent. At one point I needed to reset the power supply because the reset was not working and I then received a boot error that told me that system files are missing or corrupt. I have had this problem before and had to reformat after a power failure reset my system.
Next I tried to reformat and reinstall Windows XP Pro and started having problems there. I am ready to start over and would like to ask for some advice or see if there is any known issues or conflicts with my setup. I also have Powerquest Drive Image and have an image from about a month ago. Do you think that it would be feasible to use it?
I am running an AMD Athlon 1700+ on a K7T Turbo2 with 768mbs Kingston PC133 Ram, 2 Maxtor 40g hard drives, 300 watt Allied PSU, Radeon 7200 32mbs Graphics card, 56k modem, Satellite internet.
Thank you,
Hank

I finnaly got the Athlon 1700 to work. It seems that my Cd Rom drive lens was dirty and I had the "crap in, crap out" syndrome. It was not the power supply nor the Ram, it was faukty software that was read by a CD Rom that I have not cleaned in 3 years...lol.....a recommendation, clean your components ofter.
I am yet to see the final outcome, but so far no crashes. I set up a dual boot, Win 98 and XP Pro machine now and seems to run great thus far.
I apprecate all of your help and input in this matter!
Hank

K7T Turbo2 and Athlon XP 2400+

Hello everyone !
I have a question about K7T Turbo2 motherboard and BIOS update.
Here it goes: I reacently bought Athlon XP 2400+ and installed it on my mobo.
But after reboot my PCU wasn't recognised and I read on MSI website that I had to
upgrade my BIOS from 3.5 to 3.6 ( I think, don't remmeber the version ) . So I did that too
and this time bios showed my CPU as XP 1800+. I said there is something wrong with CPU or
they gave me a wrong one, but NO. After reading the manual I realised that that XP 2400 uses
266 insted of 100 ( standard that came with mobo )and that I had to remove J17 jumper to make it
work and also had to change options in BIOS --> like FBS 133 and multiplier 15 to get XP2400.
Reason that I'm expling what I did is to let you know what stuff I did before I came to this forum to
ask a Q. Anyway after all of that fuss PC works and shutdowns OK. But ( yeah there is a but ) now insted
of starting at once I need to press power button one time -> and you can here power starting and lights
showing but system not starting. Then I push and hold button for a few sec to shut it down. After
second push of power button system starts as normal. It looks like it need a bit of warm up ( like my car in winter time ) before it actuali start. Is this a BIOS error becouse it can't start the system with ONE
push of the button? Never had tha problem with Duron CPU and old BIOS. Need some help ..
Thanks

Hi!
I think I solved your problem! It seems that I had exactly the same problem and the same settings you have. Then, I read this Trouble Shooting Guide at:
https://forum-en.msi.com/index.php?threadid=1131&sid=
which says:
"As for mulipliers with AMD CPU's, just set them Automatic, as they are hardcoded on the CPU themselves and will allway's be correctly, even if if you think the BIOS doesn't know it."
So I changed the multiplier from BIOS from 15 to Default, and now it starts up great even at the first time! Even my CPU benchmark score with PCMark2002 free went up from 5195 to 6344 so now it actually works much better than with the multiplier 15!!
Try this before buying a new PSU and tell if it helps...
Regards,

K7T Turbo2 and XP 2600+

Hi all, I have a K7T Turbo2 Motherboard with the latest Bios. I have just replaced the XP 1800+ Chip with an XP 2600+ one. I have set the CPU clock to 133Mhz but the computer will only run at 2000+ maximum, any help would be greatly appreciated,

The core speed of the 2600+ is 2083Mhz or 2133Mhz, not 2600Mhz as suggested by the name. AMD logic
Going any higher than those specified clock speeds is overclocking and might result in an unstable system. You might get it somewhat stable by tweaking the cpu vcore voltage and stuff.. but this is generally not recommended

K7T - Turbo2 and Athlon 2000+ problem

Sorry for my english...
K7T Turbo2 - BIOS 3.6. Problem with Athlon 2000+. I can´t set the multilplier to 12.5, because there is only 12 - 13 step. When i set it to "Default" POST show CPU correctly as Athlon 2000+, but pc can´t be rebooted by ctrl+alt+del. Must be switched off and then on...
Second thing is... it´s impossible to install win98 or xp - blue death.
With Duron 1.3 it´s working fine ...

Hi,
I don't think ECC memory is supported by the Turbo2, it states "NO support ECC Function" on the MSI info page, look here
So, I'm not sure that ECC bios function will help you, or what it is really there for.
But, I guess this opinion will not explain why you said it will work with an duron 1.3
Another thing is that the XP2000 uses more power than the duron 1.3, so your PSU sounds a bit weak for the XP2000 cpu;
PSU 300W
5V - 24A
12V - 10A
3.3V - 14A

K7t turbo2 and memory problems!!!

Hi guys. Need your help w/ this weird situation. I am plagued by hangups w/ my system. One of you told me that maybe my memory was bad so I bought a spanking new 256mb pc133 dimm SDRAM...and my comp still hangs. When I use both of my 256 it still hangs when windows is about to start. Strangely, I could use my comp. w/ my original 256 w/ just occasional hangups..but since last week it hangs everytime windows xp pro or win2000 pro starts. I see the stuff loading and my desktop icons and then wham!! it freezes. But here's the funny thing...when i use my old 64mb pc100 mem it works perfectly, except that it is extremely slower..BUT NO HANGUPS. Now I'v crossed off several suspects off my list 1) my 256 mem sticks aren't bad cause the brand new one does the same thing as the older one, so there's no static or anything 2) my power supply s/d be ok it's 350W and even when i unplug all my drives and leave just 1 hard drive it still hangs w/ the 256 or 512 (mixed). So i'm wondering if it's 1) some config in the bios i need to tweak...but like i said it used to work fairly well w/ the 1st 256 untill recently or 2) my cpu is an AMD athlon 1333, which gives me 1ghz and it can only run at a clock of 100. if i unjumper J17, it can't run at 133. So i'm wondering if it's because my mem sticks are running at 133 but the cpu is 100..it causes a prob and thus hangs; and my 64 mb mem stick is at 100mhz..so it's the same clock speed as my cpu. But if that was it..how comes I used to run the 256 pc 133 w/ this same cpu w/ just hangups occasionally ..but now I can't start windows any at all??? any ideas w/d be welcomed. Also, could u tell me a couple athlon xp that u know for sure run at 133 mhz clock speed, eg: can the xp 1700 run at that. I have an MSI K7T turbo2, 2 hard drives (10G & 30G) winxp and win200, both pro..and an amd athlkon 1333 (not xp) :O X(

What is the CAS latency rating of both your 256 stick ?
On the issue of running a pc133 ram in 100 it should work fine as u underclock the ram instead of over it.
I am using k7t turbo2 rev 5.0 with 133 enabled.

K7T Turbo2 and illegal opperations

running K7T turbo2 (BIOS v.3.6) with AMD XP1600+ processor (shows as "unknow" type 1600+ during POST) and i am getting illegal operations out the wazzu. OS is Win98SE. Always the exact same error regardless of the application that falls victim "error in module at 0000:606045DF". Being the exact same error each time tells me it is a hardware issue as opposed to a software issue. Installed componants are just bare minimum for operation, AOpen GF4 MX440 vid card, WD 40G ATA100 HD, unknown brand 128MB PC-100 RAM. no conflicts listed in the windows device manager. I have tried with different RAM of the same brand and type with no change, both ram sticks and got registry errors. Tried with Kingston PC-133 256MB and the system will constantly reboot (different issue I am sure) but if it stays running long enough I get the same illegal operation error.
heat is not an issue, on all my trips to CMOS, the temp has never been above 42C
anyone have any other thoughts? I think I have narrowed it down to either the motherboard or the processor

did not clear CMOS before installing the CPU as it was the first to be installed on this board but have cleared CMOS since as part of the trouble shooting, when first building the system I neglected to remove the bus speed jumper and it would not even get to the POST but I can try that again if it will not damage anything. I am also talking to Kingston about the pc-133 ram (those errors might be a bad stick)
can not get the new updates because the system will not run error free for long enough, aslo I am getting some access errors with the wondows update site requireing an administrator login when I have never setup a password on the system (again an unrelated issue)
also since the my initial post I have tried a differetn power supply and it ran longer before giving me that error

K7T Turbo2 CPU help AMD 2400+ Thoroughbred modal 8

hi nned a bit of help i have just got a AMD 2400+ Thoroughbred modal 8 CPU and i have updated the K7T turbo2 bios to the newest 3.6 off the MSI site atm it has a duron 1gz in it now when i fited the 2400 all get get when powering up is a black screen and as soon as i fit the 1ghz back in it works fine any info would be great cheers

Are you sure the cpu is good? It should work fine in your motherboard. Please furnish us info about the rest of your system.

K7T Turbo2 and XP2400

I discovered that they now rate the K7T Turbo2 as compatible with a 2400XP thoroughbred, but I installed one and it is recognized as an xp1800.
This is a 266FSB throughbred 2400XP and I've flashed the latest bios, but the clock wont go beyond 15 x 100MHz.
Has anyone else had this problem? Is there an obvious solution that I'm overlooking?

Thanks, I checked the online manual and you're right.
Also, kudos for such a quick response.
I had a 1400 tbird, the heatsink fan started making noise so I replaced it. I didn't put the heatsink on very firmly and promptly melted down the cpu. This upgrade will last me a bit longer until I have to change out the whole thing.

K7T Turbo2 and ATI 9600?

Greetings All,
I am considering an ATI 9600 video card and was wondering if it would work with the K7T Turbo2? I read that it requires APG 4x (1.5 volt) and could not find any mention of the voltage for the AGP slot on the Turbo2. It does say that it is AGP 4X but no mention of volts. I would just hate to get the card and fry it. Thanks for your advice.
Dave

Good choice - no problems to be expected :D

K7t Turbo2 and gfx card compatibility

Does anyone have any experience with ones of these:
http://www.cptech.com.tw/powercolor/web/product_inside.asp?prd_id=Radeon9700XR97-C3#
running on a turbo2 ? i would appreciate feedback, if there are any problems, as my gf2 mx 400 is getting a tad old,and needs replacing ;( it has served me well, but its time is limited, doom3 is coming.

thanks for info bas, glad to hear it. :D
Only 300w. Already have xp 2400+, i have no problems now, but I know if i get a morep owerful gdx card, ill need a new psu.

K7t Turbo2 and an AMD Athlon XP 2600+

Similar Messages

Maybe you are looking for