K7T TURBO2 (mandrake linux)

OK running the K7T TURBO2 mobo in my system with a 800 MHZ Duron.I downloaded Mandrake Linux 9.1 and looking to install it.My question is.Does anyone know if this version of mandrake will have the drivers for this board and say for the sound or are they out there for me to download.Linux newbie here so want to make sure when i install I do it right the first time.Thank You

Hi,
I think that it should be no problem to run Linux with a Turbo2. I think I would wait a few weeks until 9.2 is freely available, btw
You will probably find more information at:
http://www.mandrakelinux.com/en/
or
http://www.mandrakeclub.com/
Hope this helps,
Hans

Similar Messages

MSI K7t Turbo2

Hello. I Speak Spanish. I can´t speak English. but...........
Does MSI k7t Turbo2 Support any Linux Mandrake ?
I want to install Mandrake 9.0. It doesn´t matter if is higher or lower.
I only want to know if it is possible or not.
Excuse me for my English.
Thank you very much.

..................................?????
Please..my english is very bad.
Help me pleaseeeeeeeeee...........

K7t Turbo2 and an AMD Athlon XP 2600+

I recently flashed the BIOS on my K7t Turbo2 board to the 3.6 version which supports AMD Athlon XP processors up to 2600+. However, after I installed the new cpu, set the core voltage to 1.65, the multiplier to 11.5 and the DCM value to 166 the computer would not boot. Instead I received a simple "Beep" then two to three seconds later, another "Beep." This continues to no avail and it takes almost ten "hard reboots" which is killing my hard disks to even get back into the BIOS configuration, wherein I modified the DCM settings to 133 instead of 166. Now the computer boots but continues to tell me:
Unknown Processor at 1533mhz
When I did get it to run at 1910mhz (notice 1910, not 1917 as it should be), it also said Unknown Processor. Then, on one of the three ocassions I was actually able to boot the computer at the higher clock speed, none of my drives appeared. On the second ocassion, the Linux boot process froze and on the third, Windows XP wouldn't boot. Now, if anyone has any suggestions as to what BIOS settings I can try, or even resetting my BIOS to a previous version, then trying to reflash it, that would be great.... If, however, this is more of an issue with an MSI BIOS patch, please release another version that works. Thanks much!
-Adam

Go with the Tbred 2400+ bud, Thats what i have at the mo in my KT3 Ultra 2C, and with my old MSI ti4200 with 128mb, it kept up with a K7N2 Delta ILSR which is running a Barton 2600+ and an MSI FX5600XT with 256mb (that rig only beats me on the extra test in 2001se and 2003 that the FX card covers).
Cant wait for my K7N2 Delta ILSR to arrive to go with my Ti4600.
Should happily blow the Barton rig away

Error message with install of Oracle 9.2 on Mandrake Linux 9.0

Hi,
I hope somebody can help with this. I'm getting an error message during the installation for oracle 9.2 on mandrake linux 9. An error get thrown saying the IP address of a host cannot be determined.
Here is what is in the log:
*** Database Configuration Page***
TitleLabel = Database Configuration
Prompt = Select a database suited to your needs.
ConfigList = General Purpose,Installs a pre-configured database optimized for general purpose usage,Transaction Processing,Installs a pre-configured database optimized for transaction processing,Data Warehouse,Installs a pre-configured database optimized for data warehousing,Customized,Allows you to create a customized database. This option takes longer than the pre-configured options,Software Only,Installs software only and does not create a database at this time,
Selection = s_cfgtyperet = General Purpose
Setting value of s_dbcaProgressOnly to -progress_only
Setting value of b_autoStartApache to true
Setting value of b_launchNETCA to true
Calling query netQueries2.2.0.7.0 getHostIPAddress
Query Exception: UnknownHostException
Query Exception Class: class oracle.sysman.oii.oiil.OiilQueryException
Anyone know how to resolve this error and whether or not it is very critical to the oracle installation?
Cheers
Johnny

Hi johnny,
You should first check the hosts file to see if the correct hostname and the IP address are shown. You can also check if the "hostname" command returns the correct result. If everything looks good so far, then next check if command "nslookup" returns the correct IP address. If the nslookup <hostname> command returns error, you will need to talk to the Domain Name Server (DNS) administrator to correct this network configuration problem.
Yogi

Mandrake Linux 8.0 - can't get Oracle Universal Installer to run

Hi all.
I'm having trouble getting Oracle's Universal Installer to run.
I'm trying to become DBA certified, so I went and purchased
(among
other materials) a book titled "Oracle8i for LINUX Starter Kit",
authored by Steve Bobrowski, published by Oracle Press / Osborne
McGraw-Hill, ISBN 0-07-212442-3.
The book includes a CD-ROM with Oracle8i Enterprise Edition,
Release 2, version 8.1.6 for LINUX.
I'm running an Intel P-III 500 MHz with 512MB RAM, 30GB hard disk
exclusively configured for Linux (no other O/S on it) and Oracle
(so LOTS of hard disk space is available), Matrox Millennium G400
video card (32MB).
My hardware exceeds all requirements listed in aforementioned
book, and also in Oracle's own documentation (from their web
site).
I'm running Mandrake's Linux 8.0, PowerPack Edition, with:
kernel = 2.4.3
XFree 4.0.3 (and I've also tried 3.3.6, with identical results
to those listed below)
glibc 2.2.2
I've followed the book's instructions to the letter, and set up
the environment variables, oracle user, and subdirectories as
required.
So far, so good.
OK. Now, here's where the problem appears:
I log in as the oracle user, and try to start the Oracle
Universal Installer (following the instructions in the book)
as follows:
cd /mnt/cdrom
./runInstaller
The computer tries to do some stuff, then spews the information
listed at the bottom of this posting to the screen. I press
<ENTER> after "OK" and get dumped back to the bash prompt.
That's it. I can't go any further. No Oracle Universal
Installer.
By the way, I've also downloaded Oracle8i Enterprise Edition
Release 3, version 8.1.7 from Oracle's website, and tried to
install that, too. Exactly same results.
The nice folks at Oracle have politely told me to get lost,
and not bug them for unpaid support.
I'd really like to get this stuff up and running, so I can
start studying and practicing for DBA, but I need help 'cause
this problem is beyond me.
So... can anyone help??
Thanks in advance.
[email protected]
[email protected]
=================================================================
=========
Here's what shows up when I try to start the Oracle Universal
Installer:
[oracle@localhost cdrom]$ ./runInstaller
[oracle@localhost cdrom]$ Initializing Java Virtual Machine
from ../stage/Components/oracle.swd.jre/1.1.8/1/DataFiles/Expande
d/linux/bin/jre. Please wait...
SIGSEGV received at bfffedac
in /mnt/cdrom/stage/Components/oracle.swd.jre/1.1.8/1/DataFiles/E
xpanded/linux/lib/linux/native_threads/libjava.so. Processing
terminated
Sat Sep 29 12:58:56 2001
jre full version "JDK 1.1.8 IBM build l118-20000429 (JIT
enabled: jitc)"
Operating Environment
Host : localhost.localdomain.localdomain
OS Level : 2.4.3-20mdk.#1 Sun Apr 15 23:03:10 CEST 2001
glibc Version : 2.2.2
No. of Procs : 1
Memory Info:
total: used: free: shared: buffers: cached:
     Mem: 525901824 116862976 409038848 0 6377472
61140992
     Swap: 1069244416 0 1069244416
     MemTotal: 513576 kB
     MemFree: 399452 kB
     MemShared: 0 kB
     Buffers: 6228 kB
     Cached: 59708 kB
     Active: 63740 kB
     Inact_dirty: 2196 kB
     Inact_clean: 0 kB
     Inact_target: 1072 kB
     HighTotal: 0 kB
     HighFree: 0 kB
     LowTotal: 513576 kB
     LowFree: 399452 kB
     SwapTotal: 1044184 kB
     SwapFree: 1044184 kB
     User Limits (in bytes except for NOFILE and NPROC) -
     RLIMIT_FSIZE : infinity
     RLIMIT_DATA : infinity
     RLIMIT_STACK : 2093056
     RLIMIT_CORE : 0
     RLIMIT_NOFILE : 1024
     RLIMIT_NPROC : 16383
Application Environment
Signal Handlers -
SIGQUIT : ignored
SIGILL : sysThreadIDump (libjava.so)
SIGABRT : sysThreadIDump (libjava.so)
SIGFPE : sysThreadIDump (libjava.so)
SIGBUS : sysThreadIDump (libjava.so)
SIGSEGV : sysThreadIDump (libjava.so)
SIGPIPE : ignored
SIGUSR1 : doSuspendLoop (libjava.so)
Environment Variables -
PWD=/mnt/cdrom/install
LTDL_LIBRARY_PATH=/usr/lib
ORACLE_SID=oralin
TMPDIR=/usr/oracle/tmp
XAUTHORITY=/usr/oracle/.Xauthority
mc=
LC_MESSAGES=en_US
HOSTNAME=localhost.localdomain
LD_LIBRARY_PATH=/mnt/cdrom/stage/Components/oracle.swd.jre/1.1.8/
1/DataFiles/Expanded/linux/lib/linux/native_threads:/lib:/usr/lib
:/usr/lib
NLSPATH=/usr/share/locale/%l/%N
CLASSPATH=/usr/oracle/tmp/OraInstall:../stage/Components/oracle.s
wd.oui/1.7.0.18.0A/1/DataFiles/Expanded/lib/OraInstaller.jar:../s
tage/Components/oracle.swd.oui/1.7.0.18.0A/1/DataFiles/Expanded/l
ib/InstImages.jar:../stage/Components/oracle.swd.oui/1.7.0.18.0A/
1/DataFiles/Expanded/lib/InstHelp.jar:../stage/Components/oracle.
swd.oui/1.7.0.18.0A/1/DataFiles/Expanded/lib/oracleice.jar:../sta
ge/Components/oracle.swd.oui/1.7.0.18.0A/1/DataFiles/Expanded/lib
/help.jar:../stage/Components/oracle.swd.oui/1.7.0.18.0A/1/DataFi
les/Expanded/lib/ewt.jar:../stage/Components/oracle.swd.oui/1.7.0
.18.0A/1/DataFiles/Expanded/lib/xmlparser.jar:../stage/Components
/oracle.swd.oui/1.7.0.18.0A/1/DataFiles/Expanded/lib/swingaccess.
jar:/mnt/cdrom/stage/Components/oracle.swd.jre/1.1.8/1/DataFiles/
Expanded/linux/lib/rt.jar:/mnt/cdrom/stage/Components/oracle.swd.
jre/1.1.8/1/DataFiles/Expanded/linux/lib/i18n.jar:/mnt/cdrom/stag
e/Components/oracle.swd.jre/1.1.8/1/DataFiles/Expanded/linux/lib/
math.jar:/mnt/cdrom/stage/Components/oracle.swd.jre/1.1.8/1/DataF
iles/Expanded/linux/lib/classes.zip
LESSKEY=/etc/.less
LANGUAGE=en_US:en
LESSOPEN=|/usr/bin/lesspipe.sh %s
BROWSER=kfmclient openProfile webbrowsing
LESS=-MM
USER=oracle
LC_TIME=en_US
LS_COLORS=no=00:fi=00:di=01;34:ln=01;36:pi=40;33:so=01;35:bd=40;3
3;01:cd=40;33;01:or=01;05;37;41:mi=01;05;37;41:ex=01;32:*.cmd=01;
32:*.exe=01;32:*.com=01;32:*.btm=01;32:*.bat=01;32:*.tar=01;31:*.
tgz=01;31:*.tbz2=01;31:*.arc=01;31:*.arj=01;31:*.taz=01;31:*.lzh=
01;31:*.lha=01;31:*.zip=01;31:*.z=01;31:*.Z=01;31:*.gz=01;31:*.bz
2=01;31:*.bz=01;31:*.tz=01;31:*.rpm=01;31:*.jpg=01;35:*.jpeg=01;3
5:*.gif=01;35:*.bmp=01;35:*.xbm=01;35:*.xpm=01;35:*.png=01;35:*.t
if=01;35:*.tiff=01;35:
THREADS_TYPE=native_threads
MACHTYPE=i586-mandrake-linux-gnu
KDE_MULTIHEAD=f
KDE_MULTIHEAD=false
HELP_BROWSER=kfmclient openProfile webbrowsing
THREADS_FLAG=native
MAIL=/var/spool/mail/oracle
INPUTRC=/etc/inputrc
GTK_RC_FILES=/etc/gtk/gtkrc:/usr/oracle/.gtkrc
XMODIFIERS=@im=none
LANG=en
JAVA_HOME=/mnt/cdrom/stage/Components/oracle.swd.jre/1.1.8/1/Data
Files/Expanded/linux
ORACLE_BASE=/usr/oraInventory
LC_NUMERIC=en_US
COLORTERM=
ORACLE_HOME=/usr/oracle
TMP=/usr/oracle/tmp
DISPLAY=localhost:0.0
LOGNAME=oracle
SHLVL=3
LC_CTYPE=en_US
SESSION_MANAGER=local/localhost.localdomain:/tmp/.ICE-
unix/1074
SHELL=/bin/bash
HOSTTYPE=i586
QT_XFT=0
OSTYPE=linux-gnu
HISTSIZE=1000
HOME=/usr/oracle
TERM=xterm
PATH=/bin:/usr/bin:/bin:/usr/bin:/usr/X11R6/bin:/usr/local/bin:/u
sr/X11R6/bin:/usr/games:/usr/oracle/bin
SECURE_LEVEL=3
LC_MONETARY=en_US
RPM_INSTALL_LANG=en_US:en
LC_COLLATE=en_US
LIBPATH=/mnt/cdrom/stage/Components/oracle.swd.jre/1.1.8/1/DataFi
les/Expanded/linux/lib/linux/native_threads
Libraries Loaded by the JVM
<main>
libjitc.so
libzip.so
Current Thread Details
"main" (TID:0x4032a2d8, sys_thread_t:0x804de98)
Native Thread State: ThreadID: 00000400 Reuse: 1 USER
PRIMORDIAL RUNNING
Native Stack Data : base: bfffef08 pointer bffdf764 used
(128932) free(-12196)
----- Monitors held -----
----- Native stack -----
Java_java_lang_System_initProperties_stub
invokeNativeMethod
invokeLazyNativeMethod
__irem_trap6
------ Java stack ------ () prio=5 *current
thread*
java.lang.System.initializeSystemClass(System.java)
Total Thread Count: 3
Active Thread Count: 3
JNI Thread Count: 0
Full thread dump:
"Async Garbage Collector" (TID:0x4032a238,
sys_thread_t:0x80dca78)
Native Thread State: ThreadID: 00000803 Reuse: 1 DAEMON
MONITOR WAIT
Native Stack Data : base: bf5ffb20 pointer bf5ff914 used
(524) free(116212)
----- Monitors held -----
----- Native stack -----
sysMonitorWait
sysThreadSleep
threadSleep
SetOrigArgs
sysThread_shell
pthread_detach
__clone
------ Java stack ------ () prio=1
"Finalizer thread" (TID:0x4032a288, sys_thread_t:0x80dc7f8)
Native Thread State: ThreadID: 00000402 Reuse: 1 DAEMON
MONITOR WAIT
Native Stack Data : base: bf7ffb20 pointer bf7ff988 used
(408) free(116328)
----- Monitors held -----
----- Native stack -----
sysMonitorWait - waiting on Finalize me queue lock
finalizeOnExit
sysThread_shell
pthread_detach
__clone
------ Java stack ------ () prio=1
"main" (TID:0x4032a2d8, sys_thread_t:0x804de98)
Native Thread State: ThreadID: 00000400 Reuse: 1 USER
PRIMORDIAL RUNNING
Native Stack Data : base: bfffef08 pointer bffdf758 used
(128944) free(-12208)
----- Monitors held -----
----- Native stack -----
Java_java_lang_System_initProperties_stub
invokeNativeMethod
invokeLazyNativeMethod
__irem_trap6
------ Java stack ------ () prio=5 *current
thread*
java.lang.System.initializeSystemClass(System.java)
System Monitor Status
Thread queue lock: unowned.
Name and type hash table lock: unowned.
String intern lock: unowned.
JNI pinning lock: unowned.
JNI global reference lock: unowned.
Zip lock: unowned.
BinClass lock: unowned.
Class loading lock: unowned.
Java stack lock: unowned.
Code rewrite lock: unowned.
Heap Lock: unowned.
Has finalization queue lock: unowned.
Finalize me queue lock: unowned.
Integer lock access-lock: unowned.
Monitor cache lock: unowned.
Monitor registry: unowned.
Object Monitor Status
OK
[oracle@localhost cdrom]$
=================================================================
=========
[email protected]
[email protected]

I have Mandrake 8.0 on PII-600, 256 RAM. I used the downloaded
8.1.7. Edit JRE_LOCATION in Disk1/install/oraparam.ini to point
to your version of JRE 1.1.8 v3 (JRE from
http://www.backdown.org). Then try with NUMLOCK=OFF.
I just clicked the 'typical' installation. It failed at the end
and did not install the database manager. The error message was:
SIGGEV received at bfffea90 in
/u01/app/oracle/jre/1.1.8/lib/linux/native_threads/libjava.so
Process terminated
Writing stack trace to javacore30299.txt... OK
/u01/app/oracle/product/8.1.7/bin/dbassist: line 103: 30229
Segmentation fault $JRE_EXEC -Duser.dir=$USER_DIR -classpath
$CLASSPATH DBCreateWizard $ARGUMENTS
If you get beyond this point, let me know. Good luck!

Oracle8i Release 2 (8.1.6) on Mandrake Linux 7.1

I am trying to install Oracle8i R2 on Linux Mandrake. I've got the Oracle8i EE CD. I have followed the pre-installation steps of creating the groups, user and updating the .bash_profile file for "oracle" user with all the env. variables. After, I execute runInstaller from the CD, I get the Universal Installer Welcome screen. Mouse clicks on About Oracle and Remove Installed products work fine and show message/dialog boxes. But Mouse clicks on the Help, Exit, Installed Products AND "NEXT" button have no effect. The screen remain their without taking to the next step of installation !!!
I have to exit the Universal installer using the Closing icon on the Window (top right corner).
Also, I tried "ps -ef" on the prompt after execting runInstaller. It shows around 8-10 process running under installer. Is there any known bug/issue for installter working on Mandrake linux ?
Any help/comments/assistance....?
Thanks and advance.
null

Hi Lloyd,
I have a HP Pavilion/733MHz/128MRAM Box with Mandrake 7.1 and Win98 dual boot setup.
you mentioned that u were able to install Mandrake and Oracle on a Compaq box. Did you try re-installing Linux and Oracle on the HP box. I havent received any reply. I will try some Linux forum to raise this question.
Do let me know if you come across any solution/workaround...
Best Regards,
-Sameer Rao
<[email protected]>
null

Installing XP Pro on MS-6330 (k7t turbo2)

Im having oodles of problems installing Xp pro (and even win 98) on my computer. My current setup is:
K7T Turbo2 (latest revision, with 3.5 bios)
Athlon XP 2000+
40 gig maxtor hd
hercules gamesurround fortissimo 2
Visiontek Geforce 4 MX 420 AGP
10x dvd rom
12x8x32 cd-rw
intellimouse optical (in ps2 mode atm)
standard keyboard
generic 512 pc 133 sdram (tested with various memory test, including mem86 or whatever that was called, hehe) no errors, works perfectly
Problems arise when installing xp pro (and xp home) when at the point where it says: starting windows ... then either it reboots, blue screens, with errors like: page fault in non page area, or usb.sys or something, so ive disabled usb, etc etc...
I already tried swapping out everrything from video to sound, etc, those tricks DO NOT WORK. Already tried using various settings in the bios, already tried mem timings, setting agp to 4x, or 2x, auto, manual and EA, etc... nothing seems work...
The only thing that DOES work, is disabling the internal cpu cache..why? BEATS ME?!? After its done loading hte main stuff, Im going to reinable it and see how it goes.. im tired of problems, I like the mobo, but Was having problems from the get go installing xp.. im reinstalling it now, since i was getting errors like irq_not less, that thingy there, and then stuff like ntfs error on a bsod, etc. Installed the 4 in 1's, 442's then 443's, didnt work...psu isnt really an issue, has 220 tco, and runs fine, hard drive is not damaged, neither are the other optical drivers, and im just at my wits end.. this is really starting to tick me off..
emailed msi tech support, nothing back yet... can someone PLEAES HELP!?!? What bios settings should i use for xp pro installs and stuff?? lemme know! Thanks!!! And should i REALLY reinstall service pack 1? any thoughts on this??

WEll shite, now i gotta kill 98, cause now IT aint even working...... this board sucks! Im having more problems than a ECS mobo on a good day.
Now what, ive stuck my voodoo 3 in, and im fudgin with the settings, but quite frankly, im sick of all this, if it dont work, its going back and that pc shop is gonna fix this
and heres that farking problem with xp now..
IRQL_NOT_LESS_OR_EQUAL
!?! AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAH!
*hair goes blonde, and turns super geek 5*

K7t Turbo2..Do I have a bad one?

Am new to the forums and MSI, but have been building and repairing 'puters for a few. Have a new K7T Turbo2 MS 6330 bios v 3.4 My question is: Is this a bad MBO, or is it in need of a bios update or something?
THE PROBLEM: Incomplete POST, stalling with no detection of a primary master hard drive (master slave is not connected at this time). Statement at stall is hard drive failure.
SYSTEM BUILD: K7T Turbo2 Board 6330 Bios v. 3.4, AMD Athlon 900 mHz, (3) 256K Mwave memory, 430W Antec TruePower ATX12V True 430, 40GB IBM ATA 100 7200RPM or 8GB Seagate ATA 33, 3dLabs 4x AGP 32MB VX1 Oxygen, Smartlink 10/100 NIC, onboard audio, Creative Labs 4X CDR
NEC Zip100, Mitusmi Floppy
DIAGNOSTICS: Tested the HD and IDE 80 pin connector in another system. They were OK. Tried an old Seagate 8 GB ATA33 with no alteration in MBO response. IDE cable is connected to the MBO blue connector with the blue primary IDE connector. The first or master connector at the other end is attached to the HD. Tried HDD jumpered as a master and cable select with no alteration in response. The secondary IDE devices (CDR and Zip100) do detect in the POST. Tried disconnecting the secondary devices from power and the MBO- no alteration in response at POST. I'M STUCK
Any thoughts or suggestions on this mess?
Sharon

HI It seems like you have pretty much covered all the bases. One other suggestion, Did you try to reset ESCD in bios? You seem to know pretty much what you are talking about. I have had both my TURBO2s for about a year now and both perfornm excellent but I am using 3.2 and 3.0 bios Escd resets the bit string and reconfigs the rig. Its located right under the Pnp line in bios just enable save and exit and try to reboot If it works,you will get a success on the bottom of the 2nd or third boot page. My older build has a WD drive going bad and once in a while I get this same no detect. When it does happen I just shut down by P/s switch.and turn it back on. You might also want to try a new cable as it don't take much for a poor connection .I hope this helps and if it don't rma the board as I don't think you left much out could be a bios chip going bad or something about 3.4 as that was for support of a 160gb drive and may be causing you some grief. Best of Luck,BIGDADDY51 CT USA edit: What are you getting for an led message when the stall occurs ? This may help with your diagnosis.

Java(TM) Plug-in 1.4.2_03 under Mandrake/Linux and Mozilla

I'm having problems getting applets to load/run using Mandrake/Linux 9.2 and Mozilla 1.6. Apparently the classes are failing to load.
about:plugins in Mozilla shows that it has the Java plugin loaded, but when I try to test it using one of the sample applets at http://java.sun.com/applets/jdk/1.4/demo/applets/Clock/example1.html, I get the errors shown below in the Java Console.
I have a link in my plugins directory linking to:
lrwxrwxrwx 1 tim tim 67 Jan 17 22:33 libjavaplugin_oji.so -> /usr/java/j2re1.4.2_03/plugin/i386/ns610-gcc32/libjavaplugin_oji.so*
I PRESUME I've got some sort of configuration error, but I'm unsure where to begin to look - any help will be greatly appreciated!
Tim
Java Console Error Message Log
Java(TM) Plug-in: Version 1.4.2_03
Using JRE version 1.4.2_03 Java HotSpot(TM) Client VM
User home directory = /home/tim
<snipped "help" reference message from console>
Stopping applet ...
Joining applet thread ...
Destroying applet ...
Disposing applet ...
Quiting applet ...
Joined applet thread ...
Finding information ...
Releasing classloader: sun.plugin.ClassLoaderInfo@110278e, refcount=0
Caching classloader: sun.plugin.ClassLoaderInfo@110278e
Current classloader cache size: 3
Done ...
setWindow: call before applet exists:16956179
Referencing classloader: sun.plugin.ClassLoaderInfo@110278e, refcount=1
setWindow: call before applet exists:16956179
setWindow: call before applet exists:16956179
Loading applet ...
Initializing applet ...
Starting applet ...
Connecting http://java.sun.com/applets/jdk/1.4/demo/applets/Clock/Clock.class with no proxy
Connecting http://java.sun.com/applets/jdk/1.4/demo/applets/Clock/Clock.class with cookie " "
Connecting http://java.sun.com/notfound.jsp?requrl=/applets/jdk/1.4/demo/applets/Clock/Clock.class&refurl=UserTypedURL with no proxy
Connecting http://java.sun.com/notfound.jsp?requrl=/applets/jdk/1.4/demo/applets/Clock/Clock.class&refurl=UserTypedURL with cookie " "
Connecting http://java.sun.com/applets/jdk/1.4/demo/applets/Clock/Clock/class.class with no proxy
Connecting http://java.sun.com/applets/jdk/1.4/demo/applets/Clock/Clock/class.class with cookie " "
Connecting http://java.sun.com/notfound.jsp?requrl=/applets/jdk/1.4/demo/applets/Clock/Clock/class.class&refurl=UserTypedURL with no proxy
Connecting http://java.sun.com/notfound.jsp?requrl=/applets/jdk/1.4/demo/applets/Clock/Clock/class.class&refurl=UserTypedURL with cookie " "
load: class Clock.class not found.
java.lang.ClassNotFoundException: Clock.class
     at sun.applet.AppletClassLoader.findClass(Unknown Source)
     at java.lang.ClassLoader.loadClass(Unknown Source)
     at sun.applet.AppletClassLoader.loadClass(Unknown Source)
     at java.lang.ClassLoader.loadClass(Unknown Source)
     at sun.applet.AppletClassLoader.loadCode(Unknown Source)
     at sun.applet.AppletPanel.createApplet(Unknown Source)
     at sun.plugin.AppletViewer.createApplet(Unknown Source)
     at sun.applet.AppletPanel.runLoader(Unknown Source)
     at sun.applet.AppletPanel.run(Unknown Source)
     at java.lang.Thread.run(Unknown Source)
Caused by: java.io.FileNotFoundException: http://java.sun.com/notfound.jsp?requrl=/applets/jdk/1.4/demo/applets/Clock/Clock/class.class&refurl=UserTypedURL
     at sun.net.www.protocol.http.HttpURLConnection.getInputStream(Unknown Source)
     at sun.plugin.net.protocol.http.HttpURLConnection.getInputStream(Unknown Source)
     at sun.plugin.net.protocol.http.HttpUtils.followRedirects(Unknown Source)
     at sun.plugin.cache.CachedFileLoader.download(Unknown Source)
     at sun.plugin.cache.CachedFileLoader.load(Unknown Source)
     at sun.plugin.cache.FileCache.get(Unknown Source)
     at sun.plugin.net.protocol.http.HttpURLConnection.connectWithCache(Unknown Source)
     at sun.plugin.net.protocol.http.HttpURLConnection.connect(Unknown Source)
     at sun.plugin.net.protocol.http.HttpURLConnection.getInputStream(Unknown Source)
     at java.net.HttpURLConnection.getResponseCode(Unknown Source)
     at sun.applet.AppletClassLoader.getBytes(Unknown Source)
     at sun.applet.AppletClassLoader.access$100(Unknown Source)
     at sun.applet.AppletClassLoader$1.run(Unknown Source)
     at java.security.AccessController.doPrivileged(Native Method)
     ... 10 more
Exception: java.lang.ClassNotFoundException: Clock.class

To determine if your browser can view applets, try
viewing the "Cubic" applet on the following page..
http://java.sun.com/docs/books/tutorial/2d/display/Cubi
.html
You will notice that you can manipulate the pattern of
the applet by dragging the colored squares. Thanks for the pointer - it does, indeed, work as expected.
It's a bummer that the "sample applets" are screwy, as that seems like a good place to go to confirm that you have everything configured right (well, it DID seem like a good place to go - it seems quite a bit less good now).
Thanks for the help,
Tim

Install fails for Creator on Mandrake Linux with AMD64

I tried to install the new version of Creator update 1 on my Mandrake Linux 64 bit version and it fails to find my JVM.
I'm able test my JVM by checking the version but it still fails.
I tried the -is:javahome option ---- no difference.
Tried installing the 32 bit version of JVM 1.5 update 7 does not make a difference with is option.
The installation of pervious version of 2004 creator works fine.
Any clue as to what might be the issue.
Any assitance on this matter will be greatly appreciated.

Can you post the install.log file under your installation directory? Also take a look at this page:
http://developers.sun.com/prodtech/javatools/jscreator/reference/faqs/index.jsp

Oracle Install on Mandrake Linux 9.1 (Dell Laptop 600)

I have a full install of Oracle 10G running on a Dell Laptop using Mandrake Linux 9.1:
First I did an install of the OS, I built the swap file to be 2GIGs, the /oracle partition as 5GIGS and the /home partition as 25GIGS.
I made sure to choose the Development packages and the Office packages, I did not choose any of the WEB and other stuff.
As root, edit the file /etc/sysctl.conf. Add the following lines to the end of the file:
kernel.shmall = 2097152
kernel.shmmax = 2147483648
kernel.shmmni = 4096
kernel.sem = 250 32000 100 128
fs.file-max = 65536
net.ipv4.ip_local_port_range = 1024 65000
As root, issue the following commands at a terminal:
groupadd oinstall
groupadd dba
useradd g oinstall G dba oracle
passwd oracle <supply new password>
You then need to set up the new users environment variables. Edit the file /home/oracle/.bashrc and add the following between the # User specific aliases and functions and the # Source global definitions lines. In Mandrake Linux all I did was edit the /etc/profile file and add the below at the end. This way all users get the added. Works like a charm.
ORACLE_SID=lx10g
ORACLE_BASE=/oracle
ORACLE_HOME=/oracle/10g
PATH=$ORACLE_HOME/bin:$PATH:.
export ORACLE_SID ORACLE_BASE ORACLE_HOME PATH
You can choose what you like for the ORACLE_SID: it represents what you will eventually call your database.
Make install directories, In my case, for example, I did this:
mkdir /oracle
mkdir /oracle/10g
chown -R oracle:oinstall /oracle
First when you try to run the Universal Installer do the following:
./runInstaller -ignoreSysPrereqs (this gets you by the error on the OS)
Then just follow the normal screens and at the end you should have a complete system. There is a bug in the installer and you will need to re-run the ./runInstaller and selct just the ISQLPlus* and it will then only re-install this package. It seems it misses it during the initial install. I also suggest downloading the Compaign CD and installing the APACHE and HTMDB using the same as above when running the ./runInstaller as everything else is already setup.

check pre-requisites for a Linux OS here:
Installation Guide for UNIX Systems: AIX-Based Systems, Compaq Tru64 UNIX, HP 9000 Series HP-UX, Linux Intel and Sun Solaris Contents / Search / Index / PDF
http://otn.oracle.com/pls/db92/db92.docindex?remark=homepage
Remember that the OS has to be certified to install
Oracle sucessfully.
Joel P�rez

New BIOS for K7T Turbo2

I just downloaded the latest BIOS from your site (W6330VMS.360) and was planning on installing an Athlon XP 2600+ CPU. I was expecting to see a CPU multiplier of 16 available in the BIOS settings but it only goes up to 15. Can I still install a 2600+? What would the multiplier be?

Quote from: zillafan on 07-December-06, 21:41:20
I just downloaded the latest BIOS from your site (W6330VMS.360) and was planning on installing an Athlon XP 2600+ CPU. I was expecting to see a CPU multiplier of 16 available in the BIOS settings but it only goes up to 15. Can I still install a 2600+? What would the multiplier be?
Hello,
should be x16 Multi. i can't see manual selection for x16 multi too.
in BIOS description: -Support AMD XP 2400+ & 2600+ (K7T Turbo2 only)
i have checked inside and confirm that 2600+ ratting exist(323630302B@00009EA0)
i guess you should leave/setup "CPU Clock Ratio" to Default(not to override/force custom values), BIOS will ask CPU for his default multi by vid and should apply correct one.
think should be fine

After replace the ATX case for K7T Turbo2 mainboard???

hi, Master outhere help plz...
after replace the ATX case for K7T Turbo2 mainboard??? why not boot up on screen any more , but power running is ok for the CPU fan , if i forgot any thing from this stage plz guide me the step.
thank for kindly supports soon...

psu max amps better than in old case ?
got to many stand offs under the board shorting it out ?

Problem installing weblogic server 7.0 in Mandrake Linux 10.1

hi
i am very new to Mandrake Linux ..i have installed Mandrake Linux 10.1 in my machine ...the problem is that when i try i to install weblogic server 7.0 it gives some error
** Error during execution, error code = 11
my machine spec
* 512MB RAM
* 40GB HDD
* P4 2.8GHZ
can any one help me..
the weblogic server i downloaded from bea site its version is weblogic server 7.0 with jrockit (sp6)
regards
babu

Hi,
first of all, unfortunately, WebLogic Server is not supported under Mandrivia (use the right name ;-) ), so you should use Novell Suse or Redhat AS, check this list
Anyway, error code 11 should be related to permission issues, so you should check that the user you are using is allowed to write under the installation directory and under /var/log/
Could you kindly post the log messages?
Regards.
Antenore Gatta
Middleware Specialist
Hequa S.r.l
C.so Buenos Aires 77
20124 Milano
http://www.Hequa.it
Tel +39(0)267493078
Fax +39(0)267493079
Mobile +39 3481537897
______________________________________

Sun One / Win ME / Mandrake Linux

Okay, this is driving me nuts. I am running Windows ME on one partition on my box. I used to have forte installed a while ago, btu for some reason I got rid of it. Now I am doing something that I would like to use it as a resource for and I come to find out it is Sun One now. SO I dl it and I go to install and teh installer freezes while looking for J2SDK. So I uninstalled J2SDK and dl the most recent version and reinstalled it. Still does the same thing.
So here is my question: realizing that Sun one is not particularly supported on ME, is that what is causing the install to freeze? If not, do you know what the problem might be? And if Forte installed, why oh why wouldn't Sun One.
If ME is the problem, I have Mandrake Linux on another partition (Yeah, I'd love Red Hat, but it was free and I am broke, so it seemed like a good idea) and it seems that only Red hat is supported. Should I bother downloading and trying to install on Mandrake (I use KDE btw)?

Hi,
I'm running on Mandrake 9.0 without any problems.
There is one anoying issue and thet is that the icons deliverd is in .ico format and I can't figure out how to use them on KDE 3.0
regards birger....
Okay, this is driving me nuts. I am running Windows ME
on one partition on my box. I used to have forte
installed a while ago, btu for some reason I got rid
of it. Now I am doing something that I would like to
use it as a resource for and I come to find out it is
Sun One now. SO I dl it and I go to install and teh
installer freezes while looking for J2SDK. So I
uninstalled J2SDK and dl the most recent version and
reinstalled it. Still does the same thing.
So here is my question: realizing that Sun one is not
particularly supported on ME, is that what is causing
the install to freeze? If not, do you know what the
problem might be? And if Forte installed, why oh why
wouldn't Sun One.
If ME is the problem, I have Mandrake Linux on another
partition (Yeah, I'd love Red Hat, but it was free and
I am broke, so it seemed like a good idea) and it
seems that only Red hat is supported. Should I bother
downloading and trying to install on Mandrake (I use
KDE btw)?

K7T TURBO2 (mandrake linux)

Similar Messages

Maybe you are looking for