K7T Turbo2 MS-6330 Ver5.0

I bought the above Mobo and a new processor AMD Athlon XP2000+. WHen I boot up..the screen show dat my processor onli run at AMD Athlon(tm)1250mhz.Can i know what the reason???izit the supplier have giving me the wrong processor???and I heard oso that izit the AMD Athlon XP processor need bigger walts power supply???I'm using onli 220w power supply...ANYBODY PLZ HELP ME!!!!!!!!!!!!!..............

Hi again,
Clearing CMOS will not hurt ;-) but it REALLY looks like you will have to try with a more powerful PSU. Dependent on the hardware you have, a 300-350W brand PSU will do, if you want to use a big videocard, forinstance you better go for a 400W - just make sure that it is a good quality one.
Hans

Similar Messages

K7T Turbo2(MS-6330 V5) AGP Features FAQ

Hi! I'm using K7T Turbo2(MS-6330 Ver5.0) motherboard and just bought an MSI Geforce4 MX440 64MB DDR (MS-8878 SE).
When I run some benchmarking program (eg. 3D Mark 2001), the status of sideband addressing (SBA) and fastwrite (FW) of both the card and motherboard are shown as follow:
Graphics Card:
SBA: not supported
FW: supported but not enabled
Motherboard:
SBA: supported but not enabled
FW: not supported
I tried very hard to force the SBA features using variety of software (Rivatuner, PowerStrip), but all failed.
Experts here, do you think it is possible to force on either (or both) features? I heard that there are ways to force the features in low-level.
Helps & Advices pls!
TQ!

Hi,
From MSI,
Enabling SBA & FW didnt really add much to the performance. There might be potential compatibility & stability issue when enabling SBA & FW. So we will not let be enabled
After more clarification, this explanation is for both motherboard and display card of yours!

K7T Turbo2 MS-6330 Will not boot up

Can someone help, I have a K7T Turbo2 MS-6330, and it will not boot up, I know I have power to my MB, becasue when I plug it in, the lights on my DIMM chips light up, and my fan spins for about 1/2 second. I don't know what to check next. Any assistance would be appreciated.
THANKS...

First of all, write what hardware other than mobo you have: cpu, power supply, graphics, memory, etc.
also, read troubleshooting guide:
http://www.msi.com.tw/program/service/forum/index.php?threadid=1131&boardid=13&styleid=1
Take care

MSI K7T turbo2 MS-6330 bios ver 3.6..NEED SERIOUS HELP!!

Anybody plz help me.I own a mobo above running amd athlon xp 2000+. My system run well for one week. After dat, my system started to give me problem. It hangs one day and when i reboot my com, the message "Windows protection error. Please restart your computer" appears. I tried already many times to restarted my com..but still fails. So i think maybe RAM problem..so i try to remove and reinstall the RAM. Then my com succeed to boot into windows. Everything run ok..no problem for few days. Then suddenly my com hang again and I juz reboot my com. Then the same message appears again..May i know wat happened to my com.PLEASE HELP ME...:'(
My spec:
msi K7T turbo2 MS-6330 bios ver 3.6
AMD athlon xp 2000+
Asus v7100 Geforce 2 MX400
2x256 kingston ram(pc133)
2x20g maxtor hdd
1xTV tuner card
1XSb live soundcard

Try uninstalling the sound card and any other nonessential components. Also, when you uninstall click on the "show hidden" items and remove duplicates. Don't remove anything that you do not know exactly what it is including any marked "unknown" but if you see multiple sound cards or cd-roms, etc. remove them. Then see if you boot ok and gradually reinstall items.

K7T Turbo2 MS-6330

I can't run amd xp2100 at 133 MHz with motherboard K7T Turbo2, but it works (not well) at 100 MHZ and the bios tells me that i have a AMD xp1500. I have another computer with the same motherboard but with amd xp2000 and it works well at 133 MHz. So I'm very confused !!!! a new bios version maybe? to solve this?

check cooler as this is most likley reason
is psu in one that works a better one,swap them over
use a lower vga card if a gf4 will help see if power is the issue
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=24%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20&NAME=MS-6330%20Ver5.0
bios needs to be 3.5 to be safe as thats when 2200 support added not clear were 2100 fits in

K7T Turbo2 (MS-6330) Booting problems

Last night, I installed an Athlon XP 1700+ on my K7T Turbo2 mobo. I can not boot into Windows now. Windows XP will hang on loading up mup.sys, and 98 resets at an indeterminate time. I cannot install Windows 98 or XP either, as both hang on the setup (Before I can even access recovery mode for XP). I've swapped out all my PCI devices, disabled nearly everything in the BIOS, etc... nothing good. Heres what I've got.
Athlon XP 1700+
K7T Turbo2 Mobo
ATI Radeon 9000 128mb
ATI Radeon 7200 32mb (Secondary Display)
Creative Labs Soundblaster (Live!)
1280 Megs of PC133 RAM (PNY)
Linksys 10/100 PCI Ethernet Card
Maxtor 60GB HD 7200
Maxtor 12GB HD 7200
Seagate 10GB HD 5400
Buslink 52x24x52 CDRW
Any help would be greatly appreciated! Do I need to set my FSB to 133 so I can use the 1700? I have updated my BIOS to the latest version. How would I increase the FSB?

Welcome
Shutdown and remove jumper J17 (see manual - jumper near ram slots). If no boot, clear CMOS and try again. Be sure to use Fail Safe Defaults for install.
You've got a really heavy load, and hope your PSU is up to it. Do you have at least 200-220 combined watts on +3 and +5 circuits of PSU (see PSU label or maker's site).

K7T Turbo2 PCI Problem

Motherboard: MSI K7T Turbo2 MS-6330 Ver5.0
Bios: 3.6
Chipset Driver: 4.43
Processor: AMD 1800+ XP
RAM: 256MB SDRAM PC133
HDD: WD800JB 80GB
CDROM: Generic 50x
CDRW: Lite-On 40x12x48 LTR40125S
With Windows XP Home or Windows XP Pro, I cannot install any PCI devices. I have tried a modem, NIC and a Soundblaster live. It sees the device, and knows what it is, but fails to install. I have tried different PCI slots. I have tried just about every BIOS setting (and yes I disabled the integrated modem, either though there is no integrated modem) but can't figure it out.
With Windows 98SE, no problem installing PCI devices. I did use a different hard drive to test WIN98, but I don't think that would matter.
Does anyone have any ideas? I can't seem to get through to tech support (no surprise there).
Thanks,
DTM77

Quote
Originally posted by maesus
I think this is just WinXP couldn't find the exact drivers for your PCI devices. Try to point to the driver location that you have downloaded and extracted, and manually install the driver.
Thank you for the advice, but that's not it. I did what you said.. pointed to either the CD or floppy. Even with the soundblaster, XP new it was a soundblaster and tried to install it's driver, but no luck.
I'm going to try different versions of the VIA chipset drivers today and see what happens.
DTM77

K7T Turbo2 ver5.0 won\'t reboot

I just recently bought a K7T Turbo2 (MS-6330) motherboard and I'm having a problem with it rebooting. I can't get the board to do a warm reboot. It works fine if I turn off the power and then turn it back on but even changing the BIOS settings won't allow it to reboot. I'm building this computer for someone and I will not give them a computer that won't reboot!!! I've tried to contact MSI techinical support and they have never answered me (through E-mail). I've read some other posts (in other forums) about problems with the EXACT same thing happening due to a chipset problem (KT133A) If anyone has had this problem or knows a solution please respond. here are my Spec:
K7T Turbo2 ver5.0
AMD Athlon 1200MHz (200MHz) CPU
AMD (Cooler Master) provided CPU Cooler
Matrox G400 Graphics card
2 x 64MB Crucial PC-133 Memory
P.S. I've tried other (known good) memory and graphics cards and I still have the same problem.

Well after waiting two weeks to get my replacement back from MSI I got another bad board. I haven't talked to their tech support about it yet but I think I'm going to get a different board from another manufacturer. In addition I'm going to make to STOP suggesting anymore MSI motherboards and I will definitely not choose them for my upcoming System upgrade. Just for reference.
The new board will not even POST. Or turn on for that matter. I checked all the jumpers. Unplugged everything else from the board except video, memory and processor (all proven good by another system).
I'm sick of playing with this company and I have a computer to build for someone. They just lost a formerly loyal customer. I'm not spending my money to ship it back again.
P.S.
I assume whoever sent back a KT333 motherboard and left the manual and D-Bracket in the box is going to be upset because they shipped my motherboard back in that box with the manual and the D-Bracket inside. May as well let things bounce around in the box during shipping the BOARD WAS DEAD ANYWAY!!!!!!!

Are the K7T Turbo2 and MS-6330 V5 the same MoBo

Please some one help!!!!!!!!!!!!!!!
I have a motherboard and on the motherboard the text say MS-6330 V5 and all i can find on msi homepage is a K7T Turbo2 MS-6330 v5 so is my mobo a k7t turbo2 ???????
i am lost............ ?(
i flashed my bios at my own risk with the newest bios for k7t turbo2 and it works well as hell so my thought is that my ms-6330 v5 really are a k7t turbo2 am i right ??

Hmm, I think 'MS-6330 V5' is the same as 'MS-6330 v5'... :D
So go on and buy your new cpu.

K7t Turbo2..Do I have a bad one?

Am new to the forums and MSI, but have been building and repairing 'puters for a few. Have a new K7T Turbo2 MS 6330 bios v 3.4 My question is: Is this a bad MBO, or is it in need of a bios update or something?
THE PROBLEM: Incomplete POST, stalling with no detection of a primary master hard drive (master slave is not connected at this time). Statement at stall is hard drive failure.
SYSTEM BUILD: K7T Turbo2 Board 6330 Bios v. 3.4, AMD Athlon 900 mHz, (3) 256K Mwave memory, 430W Antec TruePower ATX12V True 430, 40GB IBM ATA 100 7200RPM or 8GB Seagate ATA 33, 3dLabs 4x AGP 32MB VX1 Oxygen, Smartlink 10/100 NIC, onboard audio, Creative Labs 4X CDR
NEC Zip100, Mitusmi Floppy
DIAGNOSTICS: Tested the HD and IDE 80 pin connector in another system. They were OK. Tried an old Seagate 8 GB ATA33 with no alteration in MBO response. IDE cable is connected to the MBO blue connector with the blue primary IDE connector. The first or master connector at the other end is attached to the HD. Tried HDD jumpered as a master and cable select with no alteration in response. The secondary IDE devices (CDR and Zip100) do detect in the POST. Tried disconnecting the secondary devices from power and the MBO- no alteration in response at POST. I'M STUCK
Any thoughts or suggestions on this mess?
Sharon

HI It seems like you have pretty much covered all the bases. One other suggestion, Did you try to reset ESCD in bios? You seem to know pretty much what you are talking about. I have had both my TURBO2s for about a year now and both perfornm excellent but I am using 3.2 and 3.0 bios Escd resets the bit string and reconfigs the rig. Its located right under the Pnp line in bios just enable save and exit and try to reboot If it works,you will get a success on the bottom of the 2nd or third boot page. My older build has a WD drive going bad and once in a while I get this same no detect. When it does happen I just shut down by P/s switch.and turn it back on. You might also want to try a new cable as it don't take much for a poor connection .I hope this helps and if it don't rma the board as I don't think you left much out could be a bios chip going bad or something about 3.4 as that was for support of a 160gb drive and may be causing you some grief. Best of Luck,BIGDADDY51 CT USA edit: What are you getting for an led message when the stall occurs ? This may help with your diagnosis.

K7T Turbo2 No Bootup

i just bought the MSI K7T Turbo2 MS-6330 v5. i'm using the AMD 2000+. i was using a 350w power supply. didnt boot up. i thought it was the extra 4 pin power supply thing (that p4's have) which was the problem. i went out and bought a 400w power supply with the extra 4 pins. still didnt work. i then wondered if it was my cpu, so i tried a working AMD Tbird 1.33ghz from a different machine. still no luck. The D-Bracket gives me 4 red leds on both occassions. i know its not my cpu. i know its not my power supply. i also changed the video card from a gf2 gts to an ati 8500. no luck there. i can never get to POST. nothing ever comes on screen. a friend with same board had similar problems not getting into POST and fixed it by setting FSB from 133 to 100. he was using a Duron 950 though. i tried this method, still no luck. i've tried just about everything i know, and cant get it to work. any other tips? should i contact msi and send this board back?
-frustrated
http://www.josedawg.com
--------------------------

already did so Bas. i've built a few computers in my time, have run into many problems, but never anything like this. when i first ran into the problem, i read on the troubleshooting first, when that didnt work, i tried switching the various cpus/psu/gpu/memory. still didnt work. then i started from the beginning, broke out the mobo manual, and did it step by step. still no luck. i'm kinda pissed cuz i bought a new psu ($67, although i wouldve needed it eventually), sort-of new gpu ($40 ati radeon 8500), new cpu ($104 AMD 2000+ because i thought my previous AMD 2000+ was fried), memory ($56 PC133 PNY 512MB). i've tested the mobo with 2 cpu's (the tbird 1.33ghz and amd 2000+, am waiting for my new amd 2000+ to come in), 3 gpu's (radeon 8500, gf2 gts, tnt2 ultra, all agp), different arrangement of memory (512mb pny + 512mb kingston value ram dimm slot 0+1 and vice versa, 512mb pny alone dimm slot 0, 512mb kingston alone dimm slot 0), and with various psu's (350w antec, 250w generic, 400w powmax w/the extra 4pin adapter that mobo optionally requires). still no luck. after all this, i'm thinking i may have ordered a bad mobo, i dunno though. please help :D

K7T Turbo2 Compatibel with.....????

Just want to know if anybody know if it is true that K7T Turbo2 (MS-6330 V.5)realy is Compatibel with the XP 2700+
Course in the "CPU Support" Section on MSI Homepage says it does...??????

ABSOLUTELY NOT. The 2700 is a 333FSB XP CPU It is :D :D :D therefore NOT able to be used on a TURBO2. However the new 2400/2600 XP cpus WILL work on the board with the soon to be released 3.6 bios because they are 133/266 fsb cpus. BIGDADDY51 CT USA. ) :D :D

K7t turbo2/amd XP 1800! ack! help!

i recently bought a k7t turbo2 (ms-6330) to go with my amd xp 1800, im running 2x 512 and 1x 256 ram under winblows ME. and ever since day 1, i have random lockups when i try to move or copy files in windows, but if i use dos-prompt i can transfer files just fine... also when i try to shutdown or reboot i get error from windows. i have tried underclocking the cpu, swapping out the ram... i have installed all the most current drivers for everything and i am clueless what else to try... i got a 300w amd certified psu, 20gig maxtor along with a 20gig seagate for drives. i have disabled the onboard sound as well as the printer/serial ports... i run bare bones windows setup with no junk in the backround... have 3 case fans and amd certified cpu fan so i have eliminated temp problems, it happens whether the machine is warm or cold... i even tried upgrading the bios to 3.5 to no prevail... i have no issues running any of my games from halflife to quake to diablo to everquest... other than these 2 isuues, my systems just blazes with no issues...
any ideas?

Yank out some of that ram, like the 512k stick and then try it out . ME doesn't need all that to function. BIGDADDY51CT.USA

Installing XP Pro on MS-6330 (k7t turbo2)

Im having oodles of problems installing Xp pro (and even win 98) on my computer. My current setup is:
K7T Turbo2 (latest revision, with 3.5 bios)
Athlon XP 2000+
40 gig maxtor hd
hercules gamesurround fortissimo 2
Visiontek Geforce 4 MX 420 AGP
10x dvd rom
12x8x32 cd-rw
intellimouse optical (in ps2 mode atm)
standard keyboard
generic 512 pc 133 sdram (tested with various memory test, including mem86 or whatever that was called, hehe) no errors, works perfectly
Problems arise when installing xp pro (and xp home) when at the point where it says: starting windows ... then either it reboots, blue screens, with errors like: page fault in non page area, or usb.sys or something, so ive disabled usb, etc etc...
I already tried swapping out everrything from video to sound, etc, those tricks DO NOT WORK. Already tried using various settings in the bios, already tried mem timings, setting agp to 4x, or 2x, auto, manual and EA, etc... nothing seems work...
The only thing that DOES work, is disabling the internal cpu cache..why? BEATS ME?!? After its done loading hte main stuff, Im going to reinable it and see how it goes.. im tired of problems, I like the mobo, but Was having problems from the get go installing xp.. im reinstalling it now, since i was getting errors like irq_not less, that thingy there, and then stuff like ntfs error on a bsod, etc. Installed the 4 in 1's, 442's then 443's, didnt work...psu isnt really an issue, has 220 tco, and runs fine, hard drive is not damaged, neither are the other optical drivers, and im just at my wits end.. this is really starting to tick me off..
emailed msi tech support, nothing back yet... can someone PLEAES HELP!?!? What bios settings should i use for xp pro installs and stuff?? lemme know! Thanks!!! And should i REALLY reinstall service pack 1? any thoughts on this??

WEll shite, now i gotta kill 98, cause now IT aint even working...... this board sucks! Im having more problems than a ECS mobo on a good day.
Now what, ive stuck my voodoo 3 in, and im fudgin with the settings, but quite frankly, im sick of all this, if it dont work, its going back and that pc shop is gonna fix this
and heres that farking problem with xp now..
IRQL_NOT_LESS_OR_EQUAL
!?! AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAH!
*hair goes blonde, and turns super geek 5*

K7T Turbo2 won't boot

ok, here goes I have a MS-6330 K7T Turbo2 mobo, 256m RAM 20G Western Dig HDD NVidia GEForceMX420 64mg vid card AMD Duron 900Mhz proc. I started and it won't post, fans spin but nothing else. Cleared CMOS and it'll boot, but not RE-boot without clearing the CMOS again. I've checked the mobo to make sure it not grounding out. tried taking everything else off the mobo and it still won't post. I've taken the battery out for 10 mins, and checked it..shows good on Multimeter. I tried flashing the Bios to v3.6..no change, wouldn't post so, now I'm back to the original v3.3 because if I want to USE my computer, I first have to clear the CMOS, load defaults and then it'll boot up fine. if I've missed something PLEASE fill me in...this thing has got me COMPLETLEY stumped. If it's the motherboard I'll just buy another one rather than go through the hassle of trying to prove it's still under warranty. Help me out fellas!! PLEASE!! ?(

wow....... this is a mirror image of what happened to me almost.... to put it blunty... sounds like mobo is dying... or the cpu is dying.... but ....
did u just build this computer or did this just start up recently??? the mobo has some serious issue of POSTing when it's first installed and i have absolutely no idea why..
also... check your hsf on your cpu and c if it's it mounted properly. another thing.. r u changing anything in the bios???
Ed.
P.S. yes.. don't bother to rma. it'll take u about a month and a half to 2 months rma'ing.. i currently hate msi for how they handle my rma...

K7T Turbo2 MS-6330 Ver5.0

Similar Messages

Maybe you are looking for