K7T Turbo2 ver5.0 won\'t reboot

I just recently bought a K7T Turbo2 (MS-6330) motherboard and I'm having a problem with it rebooting. I can't get the board to do a warm reboot. It works fine if I turn off the power and then turn it back on but even changing the BIOS settings won't allow it to reboot. I'm building this computer for someone and I will not give them a computer that won't reboot!!! I've tried to contact MSI techinical support and they have never answered me (through E-mail). I've read some other posts (in other forums) about problems with the EXACT same thing happening due to a chipset problem (KT133A) If anyone has had this problem or knows a solution please respond. here are my Spec:
K7T Turbo2 ver5.0
AMD Athlon 1200MHz (200MHz) CPU
AMD (Cooler Master) provided CPU Cooler
Matrox G400 Graphics card
2 x 64MB Crucial PC-133 Memory
P.S. I've tried other (known good) memory and graphics cards and I still have the same problem.

Well after waiting two weeks to get my replacement back from MSI I got another bad board. I haven't talked to their tech support about it yet but I think I'm going to get a different board from another manufacturer. In addition I'm going to make to STOP suggesting anymore MSI motherboards and I will definitely not choose them for my upcoming System upgrade. Just for reference.
The new board will not even POST. Or turn on for that matter. I checked all the jumpers. Unplugged everything else from the board except video, memory and processor (all proven good by another system).
I'm sick of playing with this company and I have a computer to build for someone. They just lost a formerly loyal customer. I'm not spending my money to ship it back again.
P.S.
I assume whoever sent back a KT333 motherboard and left the manual and D-Bracket in the box is going to be upset because they shipped my motherboard back in that box with the manual and the D-Bracket inside. May as well let things bounce around in the box during shipping the BOARD WAS DEAD ANYWAY!!!!!!!

Similar Messages

K7T Turbo2 XP2000 won't boot up anymore!

?( i've just turned off my pc few hours ago. but now it won't even boot to BIOS.
When i turned on my PC, the HDD LED is always on (even though i hear no reading process happening) and the monitor goes blank . and strangely no error beeps from the pc speaker at all...
i've tried replugged all the components... but no hope.
i've tried testing the video card, memory, other pci cards to my spare pc that i'm using now. they worked properly.
I've tried reseating the processor and pull the BIOS battery out to clean current BIOS configuration but still no hope...
can someone pls help ?
The prolematic system specs:
AMD AthlonXP T-Bred 2000+ @ 2200+ (Global Heatsink and Fan 7000RPM)
MSI K7T-Turbo2 KT133A
512MB Kingston SDRAM pc133@143
Leadtek Winfast GeForce4 Ti4200 128mb @ 295/530
ASUS 50X CD-ROM
Samsung 24x10x40 CD-RW
WindowsXP Professional
Sound Blaster Live! Value
Logitech Webcam
D-Link 10/100mbps PCI LAN card
Creative Cambridge Soundworks 2.1

oh lol. ok. thx for the reply anyway,
With v3.6 bios can i get higher CPU more than XP 2400+?

Aopen Aeolus geforce4 + K7T Turbo2: PC won't boot!

Hi,
I have a problem getting an Aopen Aeolus GeForce4 Ti4200 (128MB) videocard to work with my MSI K7T Turbo2 motherboard (MSI-6330, BIOS v3.5).
The computer refuses to boot with the videocard installed! No POST beeps, no signal to the monitor, nothing. The videocard works in another computer and is brand new. The motherboard D-LED's flash a few times and stop at LEDs 2 and 4 being red -- "processor initialization". When the old AGP videocard is installed (old Asus RivaTNT) everything works fine again, I have no other issues with the MB.
At first MSI BIOS version 3.4 was installed. So tried updating that. I installed a new Enermax 300W power supply. Tried to boot without any cards or drives attached but nothing seems to work.
Any ideas??
thanks,
Nico

Quote
Originally posted by atmo
The combined 3.3 and 5v is 170.
Ah, I looked at the total, didn't know to look for 3.3 and 5v
Quote
These things really draw a lot of current, a (high quality) 350 watt ps would be the minimum i'd run with a geforce4.
Yes, I'll go back to the store to return my 300W and get a 450W Enermax. Pretty expensive though.
Quote
How long did you test it for in the other pc, and what else was different??
Not long, just the bootup. The owner of the PC didn't want to mess up his current config... We figured if it boots it must be OK. So only text, not even Windows... He has an Athlon 1800+ and I have a Duron 1200MHz
Researching a bit on the internet I find it strange board and card manufacturers do not seem to give more info regarding PSU's, minimun watts etc.
thanks, I'm going to try another PS
Nico

K7T Turbo2 won't boot

ok, here goes I have a MS-6330 K7T Turbo2 mobo, 256m RAM 20G Western Dig HDD NVidia GEForceMX420 64mg vid card AMD Duron 900Mhz proc. I started and it won't post, fans spin but nothing else. Cleared CMOS and it'll boot, but not RE-boot without clearing the CMOS again. I've checked the mobo to make sure it not grounding out. tried taking everything else off the mobo and it still won't post. I've taken the battery out for 10 mins, and checked it..shows good on Multimeter. I tried flashing the Bios to v3.6..no change, wouldn't post so, now I'm back to the original v3.3 because if I want to USE my computer, I first have to clear the CMOS, load defaults and then it'll boot up fine. if I've missed something PLEASE fill me in...this thing has got me COMPLETLEY stumped. If it's the motherboard I'll just buy another one rather than go through the hassle of trying to prove it's still under warranty. Help me out fellas!! PLEASE!! ?(

wow....... this is a mirror image of what happened to me almost.... to put it blunty... sounds like mobo is dying... or the cpu is dying.... but ....
did u just build this computer or did this just start up recently??? the mobo has some serious issue of POSTing when it's first installed and i have absolutely no idea why..
also... check your hsf on your cpu and c if it's it mounted properly. another thing.. r u changing anything in the bios???
Ed.
P.S. yes.. don't bother to rma. it'll take u about a month and a half to 2 months rma'ing.. i currently hate msi for how they handle my rma...

K7T Turbo2 won't power up

I just recently purchased a K7T Turbo2 mobo. I am replacing an Abit KT7A which all of a sudden stopped being able to read data of off any of my hard drives.
I installed the case connectors as shown in the owners
manuel, but can not now get it to power up. The owners manuel does not specify on the speaker ,reset switch, or the power switch, which pin is positive. Can anyone confirm which way the connectors go? Any help would be greatly appreciated, Thanks.

hi, i have that board and i have mine with the printed side of the connector all facing up,towards the cpu,both rows but that might not be your problem,double check ram and video,make sure their seated good,it takes a very hard push to get them fully inserted,good luck and let us know how you come out :P

Installing XP Pro on MS-6330 (k7t turbo2)

Im having oodles of problems installing Xp pro (and even win 98) on my computer. My current setup is:
K7T Turbo2 (latest revision, with 3.5 bios)
Athlon XP 2000+
40 gig maxtor hd
hercules gamesurround fortissimo 2
Visiontek Geforce 4 MX 420 AGP
10x dvd rom
12x8x32 cd-rw
intellimouse optical (in ps2 mode atm)
standard keyboard
generic 512 pc 133 sdram (tested with various memory test, including mem86 or whatever that was called, hehe) no errors, works perfectly
Problems arise when installing xp pro (and xp home) when at the point where it says: starting windows ... then either it reboots, blue screens, with errors like: page fault in non page area, or usb.sys or something, so ive disabled usb, etc etc...
I already tried swapping out everrything from video to sound, etc, those tricks DO NOT WORK. Already tried using various settings in the bios, already tried mem timings, setting agp to 4x, or 2x, auto, manual and EA, etc... nothing seems work...
The only thing that DOES work, is disabling the internal cpu cache..why? BEATS ME?!? After its done loading hte main stuff, Im going to reinable it and see how it goes.. im tired of problems, I like the mobo, but Was having problems from the get go installing xp.. im reinstalling it now, since i was getting errors like irq_not less, that thingy there, and then stuff like ntfs error on a bsod, etc. Installed the 4 in 1's, 442's then 443's, didnt work...psu isnt really an issue, has 220 tco, and runs fine, hard drive is not damaged, neither are the other optical drivers, and im just at my wits end.. this is really starting to tick me off..
emailed msi tech support, nothing back yet... can someone PLEAES HELP!?!? What bios settings should i use for xp pro installs and stuff?? lemme know! Thanks!!! And should i REALLY reinstall service pack 1? any thoughts on this??

WEll shite, now i gotta kill 98, cause now IT aint even working...... this board sucks! Im having more problems than a ECS mobo on a good day.
Now what, ive stuck my voodoo 3 in, and im fudgin with the settings, but quite frankly, im sick of all this, if it dont work, its going back and that pc shop is gonna fix this
and heres that farking problem with xp now..
IRQL_NOT_LESS_OR_EQUAL
!?! AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAH!
*hair goes blonde, and turns super geek 5*

K7t Turbo2..Do I have a bad one?

Am new to the forums and MSI, but have been building and repairing 'puters for a few. Have a new K7T Turbo2 MS 6330 bios v 3.4 My question is: Is this a bad MBO, or is it in need of a bios update or something?
THE PROBLEM: Incomplete POST, stalling with no detection of a primary master hard drive (master slave is not connected at this time). Statement at stall is hard drive failure.
SYSTEM BUILD: K7T Turbo2 Board 6330 Bios v. 3.4, AMD Athlon 900 mHz, (3) 256K Mwave memory, 430W Antec TruePower ATX12V True 430, 40GB IBM ATA 100 7200RPM or 8GB Seagate ATA 33, 3dLabs 4x AGP 32MB VX1 Oxygen, Smartlink 10/100 NIC, onboard audio, Creative Labs 4X CDR
NEC Zip100, Mitusmi Floppy
DIAGNOSTICS: Tested the HD and IDE 80 pin connector in another system. They were OK. Tried an old Seagate 8 GB ATA33 with no alteration in MBO response. IDE cable is connected to the MBO blue connector with the blue primary IDE connector. The first or master connector at the other end is attached to the HD. Tried HDD jumpered as a master and cable select with no alteration in response. The secondary IDE devices (CDR and Zip100) do detect in the POST. Tried disconnecting the secondary devices from power and the MBO- no alteration in response at POST. I'M STUCK
Any thoughts or suggestions on this mess?
Sharon

HI It seems like you have pretty much covered all the bases. One other suggestion, Did you try to reset ESCD in bios? You seem to know pretty much what you are talking about. I have had both my TURBO2s for about a year now and both perfornm excellent but I am using 3.2 and 3.0 bios Escd resets the bit string and reconfigs the rig. Its located right under the Pnp line in bios just enable save and exit and try to reboot If it works,you will get a success on the bottom of the 2nd or third boot page. My older build has a WD drive going bad and once in a while I get this same no detect. When it does happen I just shut down by P/s switch.and turn it back on. You might also want to try a new cable as it don't take much for a poor connection .I hope this helps and if it don't rma the board as I don't think you left much out could be a bios chip going bad or something about 3.4 as that was for support of a 160gb drive and may be causing you some grief. Best of Luck,BIGDADDY51 CT USA edit: What are you getting for an led message when the stall occurs ? This may help with your diagnosis.

K7T Turbo2 V5.0 Cannot Properly Shutdown

Hello everyone,
The thing is that "Power" button on my case doesn't work for me properly. When I'm just booting the machine, the moment I press the power button the whole system freezes (the hdd led remains on, power led goes off, fan is on, disks are on, monitor is on, boot screen is on). When I press it again, system reboots.
Many of you had the similar problem before... I tried most of the suggestions... Nothing worked for me.
When in WinXP, the moment I press "power" button, system performs the shutdown, but after the drives arу off, monitor is off etc, cpu fan remains on.
Many of you will say that my PSU is not good enough. The same PSU works wine with the same config, same cpu with Abit K7T 1.3 though.
Actually, I've been able to shut down properly once. I had my machine turned of (with the I/O switch on a PSU) for quite a while, and I cleared out the bios settings. But after the machine remains on for more that a few minutes, "power" stops working.
Please help.
Configuration:
K7T Turbo2 V5.0
1Gb PC133 RAM
AMD 1700+ Athlon XP CPU
Realtek 10/100 PCI LAN
Gforce2 GTS-V
Athlon XP certified 300W PSU
Windows XP Pro, SP1

Where did you get the CPU from and do you know for sure it was pulled from a working system? eBay, and no... :(
Are you 100% sure you have Turbo2 & the OPN on the CPU itself is AXDA2600DKV3C? Yes, I visually see them with my own eyes.
You did clean base of HSF and use fresh thermal compund/grease when installing CPU & HSF/cooler? Yes.
I assume it still works with the 1800+? Yes, using it right now.
Recheck power connections and make sure the plugs are fully seated (ATX 20 pin, JPW1 square 4 pin) I'll check that the next time, probably tomorrow.
Is PSU +12V more than 10-12 amps? No idea what you're talking about here...

K7T Turbo2 PCI Problem

Motherboard: MSI K7T Turbo2 MS-6330 Ver5.0
Bios: 3.6
Chipset Driver: 4.43
Processor: AMD 1800+ XP
RAM: 256MB SDRAM PC133
HDD: WD800JB 80GB
CDROM: Generic 50x
CDRW: Lite-On 40x12x48 LTR40125S
With Windows XP Home or Windows XP Pro, I cannot install any PCI devices. I have tried a modem, NIC and a Soundblaster live. It sees the device, and knows what it is, but fails to install. I have tried different PCI slots. I have tried just about every BIOS setting (and yes I disabled the integrated modem, either though there is no integrated modem) but can't figure it out.
With Windows 98SE, no problem installing PCI devices. I did use a different hard drive to test WIN98, but I don't think that would matter.
Does anyone have any ideas? I can't seem to get through to tech support (no surprise there).
Thanks,
DTM77

Quote
Originally posted by maesus
I think this is just WinXP couldn't find the exact drivers for your PCI devices. Try to point to the driver location that you have downloaded and extracted, and manually install the driver.
Thank you for the advice, but that's not it. I did what you said.. pointed to either the CD or floppy. Even with the soundblaster, XP new it was a soundblaster and tried to install it's driver, but no luck.
I'm going to try different versions of the VIA chipset drivers today and see what happens.
DTM77

K7T Turbo2 Hangs on bootup..HELP!!

For some reason, my Turbo2 with the latest 3.6 bios stalls during the drive initialization bootup. In other words, while it scans for the drives, floppy, cdrom and harddrive during bootup the system would just hang. I would have to press the reset buttom for the system to reboot and would bootup just fine the second time.
Why is doing this? Other than the hanging up on the first bootup after the computer has been off, the computer runs just fine.
Any ideas??
Here are the specs:
K7T Turbo2 w/ latest bios 3.6
AMD Tbird 1.3ghz
256mb PC133 SDRAM
20gig maxtor HD
TNT2 M64 32mb video card
300watt inwin S500 case
Guillemot Maxi Muse sound card
100mb internal zip drive
52x generic cdrom
1.44 floppy
Windows XP Pro with SP1

Thanks Bas,
I flashed to the latest because the latest bios allowed my k7tturbo2 to support 2400+, and 2600+ amd XP cpus. With the 3.5 it would only allow support up to only 2200+. I don't have the 2400+ as of yet, on order at the momment.
Thanks again.

K7t turbo2/amd XP 1800! ack! help!

i recently bought a k7t turbo2 (ms-6330) to go with my amd xp 1800, im running 2x 512 and 1x 256 ram under winblows ME. and ever since day 1, i have random lockups when i try to move or copy files in windows, but if i use dos-prompt i can transfer files just fine... also when i try to shutdown or reboot i get error from windows. i have tried underclocking the cpu, swapping out the ram... i have installed all the most current drivers for everything and i am clueless what else to try... i got a 300w amd certified psu, 20gig maxtor along with a 20gig seagate for drives. i have disabled the onboard sound as well as the printer/serial ports... i run bare bones windows setup with no junk in the backround... have 3 case fans and amd certified cpu fan so i have eliminated temp problems, it happens whether the machine is warm or cold... i even tried upgrading the bios to 3.5 to no prevail... i have no issues running any of my games from halflife to quake to diablo to everquest... other than these 2 isuues, my systems just blazes with no issues...
any ideas?

Yank out some of that ram, like the 512k stick and then try it out . ME doesn't need all that to function. BIGDADDY51CT.USA

Installing Audigy Card on K7T Turbo2

K7T Turbo2 mobo w/ V3.6 BIOS installed
1 gb PC133 SDRam (2 512's)
ATI Radeon 9500 Pro agp Graphics (128 mb)
SB Audigy gamer PCI sound
RealTek 10/100 nic pci
Win 2K SP4
Antec True Power 550 (550w) PS
WD 800JB as stand alone
WD 400BB in line with Sony 16x DVD player
DC output +5v (0A - 40A)
DC output +12v (0.8A - 24A)
DC output +3.3v (0A - 32A)
DC output -5v (0A - 0.5A)
DC output -12v (0A - 1A)
DC output +5v sb (0A - 2A)
Did a clean reinstall of Win2k because I felt there had been too many hardware changes since the original installation. Evidently, while I was trying to get a XP 2600+ 333 recognized as a 2600+ (I learned in the BIOS forum that this wasn't possible) the onboard sound became enabled in BIOS.
I did the reinstall without the sound card. I then attempted to add it, but of course I had a conflict between the Audigy card and the AC97 onboard. After I figured out that the onboard sound was enabled, I disabled it in BIOS. I went to safe mode and removed all hardware related to sound and all software related to Creative. I shut down again- removed the audigy card - restarted. Shut down again, inserted the audigy card in a different slot (also tried original slot). Windows doesn't recognize it. It does see a "multimedia audio controller" that I cannot find a driver for. If I cancel out of that driver installation and try to install the Creative software it advises that no sound blaster card is present.
Should I start all over again? If I do, should I install win2k with the sound card installed?
Thanks in advance for any suggestions
PS - system was working fine before I attempted the re-install but was sluggish which I felt was due to all the hardware changes (mobo, graphics card, sound card, hd) done at various times, not to mention the software installs and uninstalls.

This is the advice I rcvd from Creative technical support. It worked. Sound card is properly and cleanly installed. I also disabled the onchip sound in BIOS advanced chipset in addition to disabling the onboard audio in BIOS Integrated peripherals.
Again, this is for an audigy sound card and Win2k:
please try out the following cleansweep and
re-installation procedure instead, to see if it works:-
1. Enable the WINDOWS 2000 STARTUP MENU by rebooting your computer and
tapping F8 once every second OR holding the SHIFT key while rebooting.
2. When the menu is displayed, select SAFE MODE and press ENTER.
3. Once in SAFE MODE, insert the sound card's installation CD and exit
out of the installer
4. Click START / RUN.
5. Type "X:\AUDIO\DRIVERS\CTZAPXX.EXE into the OPEN field (replace X
with the applicable CD-ROM drive letter).
6. Click OK.
7. When the CREATIVE DRIVER UPDATE UTILITY opens, select DRIVER
UNINSTALLATION under UPDATE OPTION.
8. If two out of the three options are disabled or grayed out under
DRIVER TYPE, click OK. Otherwise, select WDM. You will then be
prompted to reboot, but please do not do so.
9. Click START / SETTINGS / CONTROL PANEL / ADD/REMOVE PROGRAMS.
10. Remove all Creative SB Audigy 2 programs.
11. Close all windows, and reboot the computer normally (ENTER NORMAL
MODE).
12. The Audigy 2 will be detected by Windows. Cancel the ADD NEW
HARDWARE WIZARD when able.
In order to install your soundcard properly, I recommend you to ensure
the following for the audio installation and test:
- The card is the only card installed other than the Graphics card.
- The card is at least one empty slot away from the Graphics card.
- Place the soundcard away from all the others.
- That the card is seated properly in the PCI slot.
- Move the PC's internal wires away from the soundcard.
- That the on-board sound on your motherboard is disabled through the
BIOS.
- That the on-board gameport is disabled through the BIOS.
- That your motherboard BIOS is up-to-date.
- That the operating system is up-to-date with the latest service packs
and patches.
- That there are no background applications open when you attempt the
solution.
- That the anti-virus program is disabled.
- That if you are over-clocking your system, return all options to their
recommended settings.
- That you access the PC with administrator rights.
13. Perform an installation via the CTRUN program on the CD
(X:\CTRUN\CTRUN.EXE where X is the drive letter of your CD drive that
has the installation CD).
[note:RE: Item 13 - there was a ctrunx directory with ctrunx.exe and start.exe in it. The ctrunx.exe wouldn't execute, but the start.exe did the job]
14. Reboot if prompted.
15. Please obtain the latest updates for your Audigy 2 card from our
website:- http://us.creative.com//support/downloads/
Under the option 'Select your product': Select 'Sound Blaster'->'24-bit
Advanced HD'->'Sound Blaster Audigy 2'.
Under the option 'Select your operating system': Select 'Windows 2000'.
Click on the 'Go' button just below the Windows selection.
In the next page, click on 'EAX 4.0 ADVANCED HD Driver Update for
Creative Sound Blaster Audigy 2/Audigy 2 ZS' and the download should
begin.
16. Once you are prompted to OPEN FROM CURRENT LOCATION or SAVE TO
DISK, select SAVE TO DISK and download the update to MY DESKTOP.
17. When the file has completed the phase of being transferred to your
computer, locate the file on your desktop and double click the file.

K7T Turbo2(MS-6330 V5) AGP Features FAQ

Hi! I'm using K7T Turbo2(MS-6330 Ver5.0) motherboard and just bought an MSI Geforce4 MX440 64MB DDR (MS-8878 SE).
When I run some benchmarking program (eg. 3D Mark 2001), the status of sideband addressing (SBA) and fastwrite (FW) of both the card and motherboard are shown as follow:
Graphics Card:
SBA: not supported
FW: supported but not enabled
Motherboard:
SBA: supported but not enabled
FW: not supported
I tried very hard to force the SBA features using variety of software (Rivatuner, PowerStrip), but all failed.
Experts here, do you think it is possible to force on either (or both) features? I heard that there are ways to force the features in low-level.
Helps & Advices pls!
TQ!

Hi,
From MSI,
Enabling SBA & FW didnt really add much to the performance. There might be potential compatibility & stability issue when enabling SBA & FW. So we will not let be enabled
After more clarification, this explanation is for both motherboard and display card of yours!

K7T Turbo2 w2k fails after SP4 or 4in1

K7T Turbo2 w/ 1800+
768 mushkin pc133
WD800 80gb ntfs
MSI 52 cd-rw
enermax 350w
Alrighty then.... I just received this mobo back after an RMA on memory problems, and am installing in a whole new box with new ps, hdd, cd-rw. (fyi - never had any problems in the old box)
I boot from cd, format entire drive to ntfs, and install w2k. the ide's are both intitially recognized as PIO (not dma). so I've tried both of the following options first and second:
1. install wk2 sp4. installs fine, goes to reboot and hangs at a black screen right after the w2k white bar goes by.
-or-
2. install the VIA 4in1's (i've tried all different rev') and I get BSOD with "inaccessible_boot_device" errors.
Did MSI send me back a lemon w/ chipset problems?
Please help. I'm on 3 sleepless nights. Thanks in advance!

yep to both replys --> hdd on primary master (no jumpers), cd-rw on secondary master (jumpered to master)
Blue ends to blue mobo plug.
I have lost track how many times I have formatted and installed this thing. I'm nearing my wits end.
What about going backwards on the BIOS? I'm at 3.6, which appears to be the latest. It seems to revolve around this hdd and the ide drivers but I don't know how to solve it. I can't believe how hard this became. It was so easy in the other machine.

MSI K7T turbo2 MS-6330 bios ver 3.6..NEED SERIOUS HELP!!

Anybody plz help me.I own a mobo above running amd athlon xp 2000+. My system run well for one week. After dat, my system started to give me problem. It hangs one day and when i reboot my com, the message "Windows protection error. Please restart your computer" appears. I tried already many times to restarted my com..but still fails. So i think maybe RAM problem..so i try to remove and reinstall the RAM. Then my com succeed to boot into windows. Everything run ok..no problem for few days. Then suddenly my com hang again and I juz reboot my com. Then the same message appears again..May i know wat happened to my com.PLEASE HELP ME...:'(
My spec:
msi K7T turbo2 MS-6330 bios ver 3.6
AMD athlon xp 2000+
Asus v7100 Geforce 2 MX400
2x256 kingston ram(pc133)
2x20g maxtor hdd
1xTV tuner card
1XSb live soundcard

Try uninstalling the sound card and any other nonessential components. Also, when you uninstall click on the "show hidden" items and remove duplicates. Don't remove anything that you do not know exactly what it is including any marked "unknown" but if you see multiple sound cards or cd-roms, etc. remove them. Then see if you boot ok and gradually reinstall items.

K7T Turbo2 ver5.0 won\'t reboot

Similar Messages

Maybe you are looking for