K7T266 Pro and Maxtor hd

Could someone please tell me if there are problems between my K7T266 Pro and Maxtor Diamond Max Plus 9 (6Y160P0)?
Thanks 4 answer

There should be no problem.

Similar Messages

Help with mega 865 pro and maxtor sata 6L300S0

i have a mega 865 pro i just install a new HDD model maxtor sata 6L300S0 300 GB and it is very slow on the mega i contact maxtor and they say i have to verify if i have correct SATA driver installed. but everything looks ok on the system. where i can download that driver again? any one can help me?
What im doing wrong?

I'm having the same problem with my Mega 865 pro and my Maxtor 6l200mo (200gb).
Seems to boot up fine, dosn't take any longer to load up startup items than my old system. Though using pretty much any program results in the system pausing and stuttering for a few seconds. I have noticed it most recenltly when watching video files (mpeg/divx). While i'm watching a video, it will keep pausing at random times.....sometimes every 5 seconds....sometimes every 5 mintues. It does the same when i'm not connected to the internet too, and does the same if I am simply playing mp3s or just on the internet! When it seems to do it most is like now! I have an mpeg playing (300mb) in a window, and while I am browsing the internet and even typing this post, it is pausing for a few seconds which is really frustrating! My old system was pretty similar spec to my current Msi system, though it wasn't a barebones system and was slighty lower spec. That worked flawlessly doing the same tasks so my guess is it must be an Ata problem. Another Mega865 gripe that is bugging me!
Any help will be much appreciated. Cheers!
P.s My hd Tach results were pretty much the same as centarlrocks

K7T266 Pro and Tbred cores

Hey everyone,
I have a good ole K7T266 Pro ver. 1 and I just bought a new processor after my old one burned up in an unrelated computer. I check the msi website a few months ago and saw that the Athlon XP was supported. Unfortunately, I didn't know things had changed since then and there was a difference between .18 and a .13. And, of course, I didn't find out there was a difference till after my order shipped. The proc I recieved was a 1.5v 1700+ 266fsb.
I've seen the other posts about the K7t266 Pro2 RU but I don't know if that info can relate to my board anyway. My BOIS does allow for voltages down to 1.55 (or 1.57) and it is a 266 board. It seems like it should be able to run it but no luck so far. I'm hesitant to try anything to the processor because I haven't heard from AMD if they will just trade me a .18 for the .13 that i have. If I knew on that, one way or the other, it would be cool. Of course my motherboard has been out of warranty for some time, so thats free for modifications. When i insert the new processor it doesn't register with the mobo (i.e. the D-LED is in the red, red, red, red state). I don't let it sit for too long but nothing appears to get hot and the proc stays cool.
If anyone has any insight to this it would be greatly appriciated. Thanks alot.

By the way, I have the built in RAID on my board. Also, my PSU is rated at 300W with 3.3v@20A and +5V@30A.

K7T266 Pro and XP200+

I tried to upgrade my K7T266 Pro with an AMD 2000+ CPU and was unsuccesful.
I first upgraded to BIOS version 1.8 (which the MSI site said would allow me to use this CPU) and then installed the CPU. I heard what sounded like the BIOS trying to Post, but no video showed up on the monitor and the system just stopped.
My system worked just fine when I re-installed my old 1.2 GHz processor.
Any suggestions would be welcomed.

Good question. I saw nothing listed on the package and I had trouble trying to track down that information on the AMD web site. I was under the impression that all 2000+ XPs were palaminos, but your question intimates that that may not be the case. If you know of a direct way to determine if the CPU is a palamino or not I would be grateful for the information.
I went through the very thorough checklist that Bas had posted (great effort on his part) and everything cleared, including the power supply unit. I guess all that would be left is an incompatible core.

What is the diffrence between K7T266 Pro and Pro2?

What is the diffrence between the pro and the pro 2, besides the pro2 being red and having the link lights. Upto what CPU and what type can the pro 1.0 handle? Also, can it be moded to fit a better cpu? Anyone know?
-Nick

Pro has the KT266 chipset
Pro2 has the KT266A chipset
KT266A has improvements that increase performance, and the Pro2 can be modified to fit Thoroughbred CPUs.
The Pro (KT266) can only accept up to the Athlon 2000+ palomino. Also, overclocking the FSB disables USB; this was fixed with the KT266A.

K7T266 Pro and ge force 4 mx 440

Running the above mother, with 512 ram, win xp home, and geforce2 32meg card (AGP). Have a new 64 meg geforce4, mx440 that, when installed gives 2 beeps plus 10 beeps during POST, and monitor, stays in s/by. Will occasionally boot...show 16mg video in boot, then hang...sometimes reset will see 64mg video in boot and starts up fine. A system shutdown then restart, will often lead to POST beeps and no picture.
Running BIOS 3.2, but 32 meg card is fine.
Any ideas??
POST codes are not in manual

http://www.google.com/search?hl=en&ie=UTF-8&oe=UTF-8&q=bios+beep+codes&btnG=Google+Search

MSI K7T266 Pro restart hangup

I am setting up a computer for my sister here are the specs:
1-1.3Ghz Duron CPU
1- MSI K7T266 pro
1- Maxtor 15gb drive
1-40x cd Rom
1-Soundblaster live
1-Savage4 pro AGP 4x
1-350watt Pwr supply
WinXP pro
Problem: works fine and boots from a complete power down but the restart feature locks up the computer and hangs without a feed to the monitor which goes to standby w/no signal. I check the specs on the ram I got and they check out on the recomended parts list. I am stumped? Any clue?? Prompt responses are greatly appreciated, I have to get this comp out of my life!!!
thanks!
-w

same here, comparable setup. The SBLive is notorious because of problems with the bus, but I don't think that is it. I had to flash back to version 3.3 of the bios before I could do a normal restart. All later bioses have this problem for me!

Msi k7t pro and hdd crash

Hi.
I have a problem and i hope some of you can help me.
I have msi k7t pro and maxtor diamond max plus 8. disk crashed before few days after using it 3 months. Before that i had maxtor 540 series and he crached after 18 months of use.
Two disk had spin up and seek time problems. Whell at least siguardian "sad that".
Could this hdd crash be from nonquality disks or the could be caused from some other part of pc.
And now i have option to chance maxtor with seagate.
What do you thing about seagate disks.
thanks

a poor psu is all i can think

K7T266 Pro WENT BOOM!!!!!

:O :O :O :O :O :O :O :O :O :O :O :O :O :O :O :O
Ok, I won this board from AMD a while back. This board was a promo to show off their new Athlon XP cpu's. I'm like, COOL. WRONG. So far this board has FRIED 2 XP 1800+ cpu's. Currently the board is in the hands of the MSI RMA dept., who will take approx 7-10 business days to determine whether the capacitor that EXPLODED, can be considered a board defect. This makes RMA #3. Now by a show of hands, who here thinks this model is defective???
Now MSI has great customer support, but, merely replacing broken products with the same model that is prone to the same problems, is not. All I asked was for MSI to not ship me a replacement K7T266 Pro, and instead ship me a K7T266a Pro. Not an unreasonable request being that both boards are pretty old. But noooooo, MSI can't do that. So far this FREE motherboard has cost me over $300 in CPU replacement costs. And they cant send me a board that costs less than $100???!!! Yea, um, ok , thats the biggest load of crap I've ever come across.
I would love to hear your thoughts on my little perdicament. Oh, and heres a pic of the latest boom:
Blown Capacitor
Electrolyte I'm guessing
And for you Forum admins, if you can do anything to help me out in this, I would really appreciate it.
A pissed off, most likely not gonna be a repeat customer no more,
John Christakos

Hi,
The CPU fan header dies when you put a High-speed-fan to it....
Happens on many boards!
As for the Cap, I also never seen any explode like that....
Most of the time the entire cap goes in the air with only leaving 2 pins behind and somepaper rubbish....
Very strange.....

CPU capacity of K7T266 PRO-R(MS-6380)

I have a motherboard as specified in the header. Now, I am not very good at computers, so I have been unable to find out what is the most powerful CPU this motherboard is able to handle. It says in my user's manual that 1400MHz is max, but someone told me that it can take more. Is there a difference between the k7t266 pro and pro-r? Can anyone please help me? I would be really grateful.
Also, my bios version is AMI v. 1.9 if this is important.
Thanks!

Hi,
This should say it all: link :D

Msi k7t266 pro-RU Spontaneous Restart and win xp install problems

i have the following system:
athlon 1200ghz cpu with thermaltake cooler
msi k7t266 pro ru ver 2 bios ver3.7
nvidia geforce 2 mx400 64mb vcard
1x 128 ddr pc1600
1x 256 ddr pc1600
1x maxtor 7200 rpm 30gb HDD (master)
1x maxtor 5400 rpm 30gb HDD (slave)
1x cd-rom
1x cd-writer
1 conexant pci modem
1 lan card
1 casing fan
1 chipset fan
i have the following problems:
1. i formatted my HDD in my other desktop and installed it in my msi system. i booted from the cd and installed winxp. after installation in windows i proceeded to install updated drivers and such. after installing drivers and win xp sp1 but before being able to install office xp, my pc restarted and its own and when it rebooted i got this messsage: cannot start windows. c:windowssystem32configsystem is corrupted. i was not able to start windows again after this.
2. after the above problem, i proceeded to attemp to install win xp again. i wasnt succesful because i always get a message saying cannot copy whatever.dll file all the time. so the installation wont continue.
i hope u can all help me. i feel that the win xp cd might be busted, but then again i am also concerned about problem #1 above. i feel that if i can install windows again i will have the same "spontanous restart" incident that first started and caused (i think) probelm #2
pls help.
thanks
Anton ;(

Hi!
Really, I don't think this could be a hardware problem since WinXp takes more than few minutes to install, and you did it, then you installed drivers and SP1. Why did you format HD in the other PC ? I would try a new install, taking out all not necesary stuff, leaving only CPU, memory and video card and formatting again the HD. for a clean install; then go adding the other hardware one by one, installing it's drivers and rebooting each time. Finally before connecting to internet enable Firewall to prevent Blaster Worm ( Don't know if still is going around ). One thing: Be sure HD is well connected and configured: Master if is a slave conected to same wire..etc.- If again you get an error, I would look for a faulty HD. 8)

K7T266 Pro R and Geforce 2 GTS problem

Hello everyone. I have been experiencing a problem for some time now regarding lockups and crashes caused by my video card, which vary in severity depending on the driver version used. Since I'm using an MSI K7T266 Pro Raid mobo (version 1) I thought I'd post my question here.
The exact problem depends on the driver version. Using any Nvidia Detonator drivers at version 40 or newer, my system becomes extremely unstable. On first booting everything seems fine, however if I try to open my Geforce display properties the Windows freezes during the redraw of the display properties window, which goes blank. Sometimes I can call up Close Programs Dialog, which shows DDHELP in the list, and [not responding]. I've never actually gotten an error message from DDHELP or any other error message -- perhaps the computer jams too hard for Windows to get one up. I've seen reports around the Net about DDHELP problems from things like DirectX 8.1, but they're never quite like my problem. The problem is identical on DirectX 8.0, 8.1, and on 9.0.
No matter what I try to do in Windows with these drivers installed, the computer will lock up in seconds. For example, if I then open IE 5.5, I might be able to get as far as a page or two before the similar thing happens: during the window redraw the computer locks up (usually with a blank or partially-redrawn window), sometimes causing the mouse to lock and sometimes not, and then if I can get the Close Program Dialog open DDHELP has appeared and is Not Responding.
The most stable driver version I've found so far is 29.42, which does not cause the lockup above and never causes DDHELP to appear. However, it is quite unstable as well, and causes Windows to lock up sporadically during 2D window redraws in various programs. For example, when calling up a Save Document dialog or when opening a pulldown menu the program will lock either before any of the redraw becomes visible on screen or when the new dialog box is "skeletal", only partially drawn. Sometimes the crash is severe enough that I have to do a cold restart on my system.
The other problem is that sporadically garbage blocks will appear in portions of my screen, like old windows and color bands popping up that do not refresh. This often happens to me in Photoshop 6, and happens usually when I'm scrolling down a window or something.
These problems with version 29.42 all appear to be 2d window-drawing related. I do not have any problems with 3d games with 29.42. However, the new reference drivers are so unstable on my system that I can't even try to open them.
With 29.42, the most stable drivers I've found so far, some kind of lockup due to redrawing windows almost always occurs within an hour (sometimes minutes) of booting up.
For what it's worth, dxdiag tests just fine.
I was hoping someone could help me figure out what's causing the trouble, what driver I should use, and how to resolve it. If possible, I'd really like to use the newer drivers as I've been told they're much faster. In any event, I hate having such an unstable system where lockups could occur at any moment!
Here's the lowdown of my system:
-MSI K7T266 Pro Raid [1] mobo (MS-6380)
AMIBIOS date: 5/1/2001
VIA 4in1 drivers version 4.45
ACPI power management disabled
PnP Aware OS enabled
-256 meg PC2100 SDRAM with 266 mhz FSB
2.5 cas latency
-AMD Athlon 1.33 gb with 266 mhz FSB
-Asus AGP-V7700 (Geforce 2 GTS) 32 mb
AGP 4X, Fast Write enabled, Aperture size 128 mb
current drivers: Nvidia reference 29.42 (also 40+)
on IRQ11 (shares with my Ethernet card)
BIOS version 2.15.01.14
-Windows 98SE
-DirectX 9.0 (also tried 8.1 etc)
-Soundblaster Live! 5.1 on slot 3, drivers from 5/2002
-Viewsonic PF790 monitor
-C drive is 30gb Western Digital 7200rpm, FAT32
-D drive is Raid 0 striped array, pair of 40gb 7200rpm
-Network Everywhere Fast Ethernet Adapter on slot 5
-no memory resident programs on loadup except for WinPoET, Explorer, Systray
If there's anything I've left out that could help, let me know!
Thanks to anyone in advance,
Raphael Tehan

Quote
Originally posted by backwoodz
You should post this in the VIA forums........If was me I would first swap the nic card to a differnt slot and try to stop the sharing of videos irq.....secondly try relaxing your memory timings to the most laxed setting
Thanks, I realized after posting this was the incorrect forum. I've put it in the VIA Socket A boards area, and also am trying the Via Arena forums.
Are you talking about my mainboard or graphics card memory?
Here's what I've got set under Advanced Chipset:
Configue SDRAM timing by: SPD
SDRAM Frequency: HCLK
SDRAM CAS# Latency: 2.5
SDRAM Bank Interleave: disabled
SDRAM 1T command: enabled
AGP mode: 4x
AGP comp driving: auto
Manual AGP comp. driving: CB
AGP Fast Write: enabled
AGP Read Synchronization: disabled
AGP aperture size: 128 mb
Do any of these settings seem problematic to you?
Thanks.

K7T266 Pro Raid and Geforce 2 GTS problem

(Originally posted to wrong group)
Hello everyone. I have been experiencing a problem for some time now regarding lockups and crashes caused by my video card, which vary in severity depending on the driver version used. Since I'm using an MSI K7T266 Pro Raid mobo (version 1) I thought I'd post my question here.
The exact problem depends on the driver version. Using any Nvidia Detonator drivers at version 40 or newer, my system becomes extremely unstable. On first booting everything seems fine, however if I try to open my Geforce display properties the Windows freezes during the redraw of the display properties window, which goes blank. Sometimes I can call up Close Programs Dialog, which shows DDHELP in the list, and [not responding]. I've never actually gotten an error message from DDHELP or any other error message -- perhaps the computer jams too hard for Windows to get one up. I've seen reports around the Net about DDHELP problems from things like DirectX 8.1, but they're never quite like my problem. The problem is identical on DirectX 8.0, 8.1, and on 9.0.
No matter what I try to do in Windows with these drivers installed, the computer will lock up in seconds. For example, if I then open IE 5.5, I might be able to get as far as a page or two before the similar thing happens: during the window redraw the computer locks up (usually with a blank or partially-redrawn window), sometimes causing the mouse to lock and sometimes not, and then if I can get the Close Program Dialog open DDHELP has appeared and is Not Responding.
The most stable driver version I've found so far is 29.42, which does not cause the lockup above and never causes DDHELP to appear. However, it is quite unstable as well, and causes Windows to lock up sporadically during 2D window redraws in various programs. For example, when calling up a Save Document dialog or when opening a pulldown menu the program will lock either before any of the redraw becomes visible on screen or when the new dialog box is "skeletal", only partially drawn. Sometimes the crash is severe enough that I have to do a cold restart on my system.
The other problem is that sporadically garbage blocks will appear in portions of my screen, like old windows and color bands popping up that do not refresh. This often happens to me in Photoshop 6, and happens usually when I'm scrolling down a window or something.
These problems with version 29.42 all appear to be 2d window-drawing related. I do not have any problems with 3d games with 29.42. However, the new reference drivers are so unstable on my system that I can't even try to open them.
With 29.42, the most stable drivers I've found so far, some kind of lockup due to redrawing windows almost always occurs within an hour (sometimes minutes) of booting up.
For what it's worth, dxdiag tests just fine.
I was hoping someone could help me figure out what's causing the trouble, what driver I should use, and how to resolve it. If possible, I'd really like to use the newer drivers as I've been told they're much faster. In any event, I hate having such an unstable system where lockups could occur at any moment!
Here's the lowdown of my system:
-MSI K7T266 Pro Raid [1] mobo (MS-6380)
AMIBIOS date: 5/1/2001
VIA 4in1 drivers version 4.45
ACPI power management disabled
PnP Aware OS enabled
-256 meg PC2100 SDRAM with 266 mhz FSB
2.5 cas latency
-AMD Athlon 1.33 gb with 266 mhz FSB
-Asus AGP-V7700 (Geforce 2 GTS) 32 mb
AGP 4X, Fast Write enabled, Aperture size 128 mb
current drivers: Nvidia reference 29.42 (also 40+)
on IRQ11 (shares with my Ethernet card)
BIOS version 2.15.01.14
-Windows 98SE
-DirectX 9.0 (also tried 8.1 etc)
-Soundblaster Live! 5.1 on slot 3, drivers from 5/2002
-Viewsonic PF790 monitor
-C drive is 30gb Western Digital 7200rpm, FAT32
-D drive is Raid 0 striped array, pair of 40gb 7200rpm
-Network Everywhere Fast Ethernet Adapter on slot 5
-no memory resident programs on loadup except for WinPoET, Explorer, Systray
If there's anything I've left out that could help, let me know!
Thanks to anyone in advance,
Raphael Tehan

Quote
Originally posted by backwoodz
You should post this in the VIA forums........If was me I would first swap the nic card to a differnt slot and try to stop the sharing of videos irq.....secondly try relaxing your memory timings to the most laxed setting
Thanks, I realized after posting this was the incorrect forum. I've put it in the VIA Socket A boards area, and also am trying the Via Arena forums.
Are you talking about my mainboard or graphics card memory?
Here's what I've got set under Advanced Chipset:
Configue SDRAM timing by: SPD
SDRAM Frequency: HCLK
SDRAM CAS# Latency: 2.5
SDRAM Bank Interleave: disabled
SDRAM 1T command: enabled
AGP mode: 4x
AGP comp driving: auto
Manual AGP comp. driving: CB
AGP Fast Write: enabled
AGP Read Synchronization: disabled
AGP aperture size: 128 mb
Do any of these settings seem problematic to you?
Thanks.

CoolerMaster CP5-7JD1B and K7T266 PRO

Hi,
The other day I installed a AMD XP2000+ with my K7T266 PRO mainbord (MS-6380). Together with the new cpu I installed a new heatsink/fan; the CoolerMaster CP5-7JD1B. Works perfect but... when starting the computer I'm getting a bios message that the fan isn't detected working and I can choose between shut down or not. But the fan is working.... Anyone any idea why this is happening ?
By the way: PCAlert and Fuzzylogic show the fan working properly and the message isn't displayed when I restart (ctrl-alt-del) the computer.

i should ingnore that.
its safe trust me
the BIOS of your mobo detect a cpu fan that runs minimum of 3000rpm.
your cpu fan is running below the 3000rpm.
thats why.
i should go into BIOS and disable the cpu fan detection at the 'hardware monitor' menu (where you see the temps).
i have that too.

MSI K7T266 Pro(MS-6380) AND Gf4 ti4600

Just recieved a Albatron gf4 ti4600 card. The computer won't boot. The card booted perfectly on a friends expo kt266a motherboard. But the card won't boot on any of my two pc's. We have tried his Enermax psu, we have tried everything. Are there any possible solution? Is there any other who has had problems with MSI K7T266 Pro(MS-6380) and gf4 ti4600 cards? we tried his Point Of View gf4 ti4200 XP card on mine and it worked.

?(
I' have the same problem with a GeForce4 MX440 !
My computer send 8 beeps and...nothing. When I retry 3 ou 4 reset, it boot and all is OK with Windows XP.
It seems there is a voltage problem with AGP slot. I post 2 mails to MSI France but they don't answer at this time...

K7T266 Pro and Maxtor hd

Similar Messages

Maybe you are looking for